Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELASTIC PROPERTY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Modeling and characterization of through-the-thickness properties of 3D woven composites

The through-the-thickness properties of three-dimensionally (3D) woven carbon/epoxy composites have been studied. The investigation aimed at the evaluation and development of test methodologies for the property characterization in the thickness direction, and the establishment of fiber architectures were studied: layer-to-layer Angle Interlock, through-the-thickness Orthogonal woven preform with surface pile was also designed and manufactured for the fabrication of tensile test coupons with integrated grips. All the preforms were infiltrated by the resin transfer molding technique. The microstructures of the composites were characterized along the warp and fill (weft) directions to determine the degree of yarn undulations, yarn cross-sectional shapes, and microstructural dimensions. These parameters were correlated to the fiber architecture. Specimens were designed and tested for the direct measurement of the through-the-thickness tensile, compressive and shear properties of the composites. Design optimization was conducted through the analysis of the stress fields within the specimen coupled with experimental verification. The experimentally-derived elastic properties in the thickness direction compared well with analytical predictions obtained from a volume averaging model.

Hartranft, Dru↗

Multi-Scale Analysis of Effective Mechanical Properties of Porous 3D Woven Composite Materials

This work aims to compute and analyze the mechanical properties of 3D woven composite materials that share the same yarn structure but differ in their matrix porosity and yarn's fiber volume fraction. Assuming linear elastic behavior, NASA's PuMA software was used to characterize the different composites from their constituents' data, averaging their elastic properties in three main directions to obtain their effective orthotropic mechanical properties. This was performed in three steps: firstly, the porous matrix phase was analyzed at the micro-scale; then, these results were used, along with the mechanical properties of the fibers, to model the yarns at the meso-scale; finally, results from the constituents were homogenized and used to model the mechanical behavior of the unit cell at the macro-scale. The 3D woven composite materials selected for this study are made of a mixture of phenolic resin with porosity values between 0 and 0.6, and infiltrated carbon fiber yarns with fiber volume fractions between 0.5 and 0.8. Results from this study show the effect of different matrix porosities and fiber volume fractions on the macro-scale mechanical properties, and were validated through theoretical and semi-empirical expressions found in the literature.

3D woven materials↗

Lattice model calculation of elastic and thermodynamic properties at high pressure and temperature

The elastic constants and the entire frequency spectrum were calculated up to high pressure for the alkali halides in the NaCl lattice, based on an assumed functional form of the inter-atomic potential. The quasiharmonic approximation is used to calculate the vibrational contribution to the pressure and the elastic constants at arbitrary temperature. By explicitly accounting for the effect of thermal and zero point motion, the adjustable parameters in the potential are determined to a high degree of accuracy from the elastic constants and their pressure derivatives measured at zero pressure. The calculated Gruneisen parameter, the elastic constants and their pressure derivatives are in good agreement with experimental results up to about 600 K. The model predicts that for some alkali halides the Grunesen parameter may decrease monotonically with pressure, while for others it may increase with pressure, after an initial decrease.

Demarest, H. H., Jr.↗

Formation of scandium carbides and scandium oxycarbide from the elements at high-(P, T) conditions

Synchrotron diffraction experiments with in situ laser heated diamond anvil cells and multi-anvil press synthesis experiments have been performed in order to investigate the reaction of scandium and carbon from the elements at high-(P,T) conditions. It is shown that the reaction is very sensitive to the presence of oxygen. In an oxygen-rich environment the most stable phase is ScO{sub x}C{sub y}, where for these experiments x=0.39 and y=0.50-0.56. If only a small oxygen contamination is present, we have observed the formation of Sc{sub 3}C{sub 4}, Sc{sub 4}C{sub 3} and a new orthorhombic ScC{sub x} phase. All the phases formed at high pressures and temperatures are quenchable. Experimentally determined elastic properties of the scandium carbides are compared to values obtained by density functional theory based calculations. - Graphical Abstract Legend (TOC Figure): Table of Contents Figure Selected images recorded with a MAR345 image plate detector show the reaction of alpha-Sc and graphite at high-(P,T) conditions. Left: mixture of alpha-Sc and graphite. Right: recovered sample after laser heated the diamond anvil cell.

36 MATERIALS SCIENCE↗

Elastic moduli reduction in SiC-SiC tubular specimen after high heat flux neutron irradiation measured by resonant ultrasound spectroscopy

The initial results of a post-irradiation examination study conducted on a SiC-SiC tubular specimen irradiated under a high radial heat flux are presented herein. The elastic properties of the specimen were evaluated before and after the irradiation using the resonant ultrasound spectroscopy (RUS) technique. The composite tubular specimen was considered as an orthotropic elastic with nine elastic constants (Young's moduli, shear moduli and Poisson's ratios—three components of each) for representing its full elastic deformation behavior. All the elastic moduli decreased after irradiation; the reduction was as high as 35% in one of the moduli. The significant decrease in the moduli indicates the presence of microcracks. The results from a computational study show significant stress development in the specimen due to irradiation, primarily caused by differential swelling across the thickness of the specimen. The evaluated stresses exceed the proportional limit stress of the material, indicating the likelihood of matrix microcracking, and thus corroborating the results obtained from RUS. X-ray Computed Tomography (XCT) study confirmed the presence of cracks in the irradiated specimen. These cracks occurred at the inner region of the specimen and propagated in axial and hoop directions. Finally, these XCT results are in agreement with the RUS results and stress distribution results from the computational study.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Ab-initio calculation of ZnGeAs{sub 2} semiconductor

The structural, electronic, optical and elastic properties of ZnGeAs{sub 2} semiconductor have been investigated using pseudopotential plane wave method within the density functional theory (DFT). The optimized lattice constants, energy gap and crystal field splitting parameter are calculated. The optical properties such as dielectric function, optical reflectivity,, extinction coefficient, absorption spectra, refractive index and electron energy loss spectrum have been studied. The values of bulk modulus (B), elastic constants (C{sub ij}), Young’s modulus (Y), Zener anisotropic factor (A), Poisson’s ratio (ν) and Debye temperature (Θ{sub D}) have been calculated. The calculated values of all these parameters are compared with the available experimental values and the values reported by different workers. A fairly good agreement has been found between them.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Rippled metamaterials with scale-dependent tailorable elasticity

Thermally induced ripples are intrinsic features of nanometer-thick films, atomically thin materials, and cell membranes, significantly affecting their elastic properties. Despite decades of theoretical studies on the mechanics of suspended thermalized sheets, controversy still exists over the impact of these ripples, with conflicting predictions about whether elasticity is scale-dependent or scale-independent. Experimental progress has been hindered so far by the inability to have a platform capable of fully isolating and characterizing the effects of ripples. This knowledge gap limits the fundamental understanding of thin materials and their practical applications. Here, we show that thermal-like static ripples shape thin films into a class of metamaterials with scale-dependent, customizable elasticity. Utilizing a scalable semiconductor manufacturing process, we engineered nanometer-thick films with precisely controlled frozen random ripples, resembling snapshots of thermally fluctuating membranes. Resonant frequency measurements of rippled cantilevers reveal that random ripples effectively renormalize and enhance the average bending rigidity and sample-to-sample variations in a scale-dependent manner, consistent with recent theoretical estimations. The predictive power of the theoretical model, combined with the scalability of the fabrication process, was further exploited to create kirigami architectures with tailored bending rigidity and mechanical metamaterials with delayed buckling instability.

Applied Physical Sciences↗

Elastic geothermobarometry: Corrections for the geometry of the host-inclusion system

Elastic geothermobarometry on inclusions is a method to determine pressure-temperature conditions of mineral growth independent of chemical equilibrium. Because of the difference in their elastic properties, an inclusion completely entrapped inside a host mineral will develop a residual stress upon exhumation, from which one can back-calculate the entrapment pressure. Current elastic geobarometric models assume that both host and inclusion are elastically isotropic and have an ideal geometry (the inclusion is spherical and isolated at the center of an infinite host). These conditions do not commonly occur in natural rocks, and the consequences for inclusion pressures can only be quantified with numerical approaches. In this paper, we report the results of numerical simulations of inclusions with the finite element method on elastically isotropic systems. We define and determine a geometrical factor (Γ) that allows measured residual pressures to be corrected for the effects of non-ideal geometry. We provide simple guidelines as to which geometries can safely be used for elastic geobarometry without correcting for the geometry. We also show that the discrepancies between elastic and conventional geobarometry reported in literature are not due to geometrical effects, and therefore result from other factors not yet included in current models.

58 GEOSCIENCES↗

High Throughput Computational Framework of Materials Properties for Extreme Environments

This project aims to establish a framework capable of efficiently predicting the properties of structural materials for service in harsh environments over a wide range of temperatures and over long periods of time. The approach is to develop and integrate high throughput first-principles calculations in combination with machine learning (ML) methods, perform high throughput CALPHAD (calculations of phase diagrams) modeling, and carry out finite element method (FEM) simulations. Relevant to high temperature service in fossil power system, nickel-based superalloys such as Inconel 740 and Haynes 282 as well as the associated (Ni-Cr-Co)-Al-C-Fe-Mn-Mo-Nb-Si-Ti system, were investigated. The present framework was built on the concept of phase-based property data, in which properties of individual phases are modeled as a function of internal and external independent variables. This project established an open-source infrastructure with the following capabilities: (1) High throughput implementation of first-principles calculations at finite temperatures and variable compositions using both accurate phonon calculations and the efficient Debye model for thermodynamic properties, elastic constants, diffusion coefficients, vacancy formation, stacking and twin faults, and dislocation mobility; i.e., using the developed code DFTTK; (2) Machine learning capabilities to predict the above properties so that the number of first-principles calculations can be significantly reduced; e.g., using the developed code SIPFENN; (3) High throughput CALPHAD modeling of the above properties as a function of temperature and composition using our unique capability based on ESPEI and PyCalphad; (4) New capabilities to predict the stress-strain behavior of individual phases; and (5) New models for tensile strength prediction in common FEM software with the crystal plasticity finite element simulations (CPFEM).

, Ni-based superalloys↗

Microtubules soften due to cross-sectional flattening

We use optical trapping to continuously bend an isolated microtubule while simultaneously measuring the applied force and the resulting filament strain, thus allowing us to determine its elastic properties over a wide range of applied strains. We find that, while in the low-strain regime, microtubules may be quantitatively described in terms of the classical Euler-Bernoulli elastic filament, above a critical strain they deviate from this simple elastic model, showing a softening response with increasing deformations. A three-dimensional thin-shell model, in which the increased mechanical compliance is caused by flattening and eventual buckling of the filament cross-section, captures this softening effect in the high strain regime and yields quantitative values of the effective mechanical properties of microtubules. Our results demonstrate that properties of microtubules are highly dependent on the magnitude of the applied strain and offer a new interpretation for the large variety in microtubule mechanical data measured by different methods.

59 BASIC BIOLOGICAL SCIENCES↗

Pressure effect on structural, elastic, and thermodynamic properties of tetragonal B{sub 4}C{sub 4}

The compressibility, elastic anisotropy, and thermodynamic properties of the recently proposed tetragonal B{sub 4}C{sub 4} (t-B{sub 4}C{sub 4}) are investigated under high temperature and high pressure by using of first-principles calculations method. The elastic constants, bulk modulus, shear modulus, Young’s modulus, Vickers hardness, Pugh’s modulus ratio, and Poisson’s ratio for t-B{sub 4}C{sub 4} under various pressures are systematically explored, the obtained results indicate that t-B{sub 4}C{sub 4} is a stiffer material. The elastic anisotropies of t-B{sub 4}C{sub 4} are discussed in detail under pressure from 0 GPa to 100 GPa. The thermodynamic properties of t-B{sub 4}C{sub 4}, such as Debye temperature, heat capacity, and thermal expansion coefficient are investigated by the quasi-harmonic Debye model.

36 MATERIALS SCIENCE↗

Electronic, elastic, and optical properties of monolayer BC{sub 2}N

The structural stability, electronic structure, elasticity, and optical properties of four types of monolayer BC{sub 2}N have been investigated from first principles using calculation based on density functional theory. The results show that the structural stability of BC{sub 2}N increases with the number of C–C and B–N bonds. By calculating the two-dimensional Young's modulus, shear modulus, Poisson's ratio, and shear anisotropic factors in different directions, four structures present various anisotropies and the most stable structure is almost isotropic. For C-type BC{sub 2}N, the values of two-dimensional Young's modulus, shear modulus, and bulk modulus (309, 128, 195 GPa m{sup −1}), are smaller than those of graphene (343, 151, 208) but bigger than those of h-BN (286, 185, 116). Furthermore, the dielectric function, refractive index, reflectivity, absorption coefficient, and energy loss spectrum are also calculated to investigate the mechanism underpinning the optical transitions in BC{sub 2}N, revealing monolayer BC{sub 2}N as a candidate window material. - Graphical abstract: Schematic diagram of BC{sub 2}N under the biaxial tensile strain. Changes in the valence-band top and the conduction-band bottom of BC{sub 2}N with increasing strain.

36 MATERIALS SCIENCE↗

Injection-Molded Long-Fiber Thermoplastic Composites: From Process Modeling to Prediction of Mechanical Properties

This article illustrates the predictive capabilities for long-fiber thermoplastic (LFT) composites that first simulate the injection molding of LFT structures by Autodesk® Simulation Moldflow® Insight (ASMI) to accurately predict fiber orientation and length distributions in these structures. After validating fiber orientation and length predictions against the experimental data, the predicted results are used by ASMI to compute distributions of elastic properties in the molded structures. In addition, local stress-strain responses and damage accumulation under tensile loading are predicted by an elastic-plastic damage model of EMTA-NLA, a nonlinear analysis tool implemented in ABAQUS® via user-subroutines using an incremental Eshelby-Mori-Tanaka approach. Predicted stress-strain responses up to failure and damage accumulations are compared to the experimental results to validate the model.

Injection molding, long fiber thermoplastic, proce↗

Sound speed measurements in shock compressed cemented tungsten carbide: Evolution of elastic moduli with damage at pressures to 100 GPa

The motivation of the present study is to gain insights into the evolution of elastic properties of cemented tungsten carbides (WC) shock compressed to 100 GPa. Seven plate impact experiments—two front surface impact and five release wave overtake—are conducted to make simultaneous measurements of Hugoniot states and longitudinal sound speeds in shocked WC with 3.7wt.% cobalt binder. The sound speeds along with estimates for bulk sound speeds, obtained using the Birch–Murnaghan EoS, are analyzed to determine the elastic moduli—longitudinal, bulk, and shear—as a function of Hugoniot stress. The longitudinal and bulk sound speeds at Hugoniot states of interest are found to increase linearly with longitudinal stress. Consistent with the increase in sound speeds, the longitudinal and bulk moduli also increase with Hugoniot stress; however, the increase in longitudinal modulus is modest when compared to predictions of theoretical models that account for pressure and temperature dependence of elastic moduli, but with no damage. The shear moduli remain nearly constant at ~318 GPa over the range of Hugoniot states investigated. These values are, however, much lower than those predicted by the Steinberg–Guinan model with no damage. Poisson’s ratio decreases initially from its ambient value of 0.208 to ~0.199 for Hugoniot stress ≤10 GPa indicating consolidation of the WC microstructure with low initial stress; however, with an increase in Hugoniot stress to ~100 GPa, Poisson’s ratio increases to ~0.317, indicating degradation of shear moduli with increasing stress. The product of density and Grüneisen parameter (ρΓ), after an initial spike, remains nearly constant for volumetric strains ≥0.07. The maximum average temperature rise is estimated to be ~286°C at the highest Hugoniot stress employed in the study.

36 MATERIALS SCIENCE↗

Exact propagating nonlinear singular disturbances in strongly coupled dusty plasmas

The dynamical response of the strongly coupled dusty plasma medium has recently been described by utilizing the Generalized Hydrodynamic (GHD) model equations. The GHD equations capture the visco-elastic properties of the medium and have been successful in predicting a host of phenomena (e.g., existence of novel transverse shear waves in the fluid medium, modification of longitudinal wave dispersion by elastic effects, etc.) which have found experimental confirmation. In this paper, the nonlinear longitudinal response of the medium governed by GHD equations in strong coupling limit is discussed analytically. The structure of the equations rules out the balance between dispersion and nonlinearity, thereby, forbidding soliton formation. However, a host of new varieties of nonlinear solutions are found to exist, which have singular spatial profiles and yet have conservative properties. For instance, existence of novel conservative shock structures with zero strength is demonstrated, waves whose breaking produces no dissipation in the medium are observed, propagating solutions which produce cusp like singularities can exist and so on. It is suggested that simulations and experiments should look for these novel nonlinear structures in the large amplitude strong coupling limit of longitudinal disturbances in dusty plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Technique development for modulus, microcracking, hermeticity, and coating evaluation capability characterization of SiC/SiC tubes

Driven by the need to enlarge the safety margins of nuclear fission reactors in accident scenarios, research and development of accident-tolerant fuel has become an important topic in the nuclear engineering and materials community. A continuous-fiber SiC/SiC composite is under consideration as a replacement for traditional zirconium alloy cladding owing to its high-temperature stability, chemical inertness, and exceptional irradiation resistance. An important task is the development of characterization techniques for SiC/SiC cladding, since traditional work using rectangular bars or disks cannot directly provide useful information on the properties of SiC/SiC composite tubes for fuel cladding applications. At Oak Ridge National Laboratory, experimental capabilities are under development to characterize the modulus, microcracking, and hermeticity of as-fabricated, as-irradiated SiC/SiC composite tubes. Resonant ultrasound spectroscopy has been validated as a promising technique to evaluate the elastic properties of SiC/SiC composite tubes and microcracking within the material. A similar technique, impulse excitation, is efficient in determining the basic mechanical properties of SiC bars prepared by chemical vapor deposition; it also has potential for application in studying the mechanical properties of SiC/SiC composite tubes. Complete evaluation of the quality of the developed coatings, a major mitigation strategy against gas permeation and hydrothermal corrosion, requires the deployment of various experimental techniques, such as scratch indentation, tensile pulling-off tests, and scanning electron microscopy. In addition, a comprehensive permeation test station is being established to assess the hermeticity of SiC/SiC composite tubes and to determine the H/D/He permeability of SiC/SiC composites. This report summarizes the current status of the development of these experimental capabilities.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Single-crystal elasticity of (Mg[subscript 0.9]Fe[subscript 0.1])O to 81 GPa

Ferropericlase is the second most abundant mineral in Earth's lower mantle and knowledge of its elastic properties at relevant conditions is needed to adequately interpret seismic observations in terms of the mineralogy and thermal state of the deep Earth. Here, we report the complete elastic tensor of (Mg{sub 0.9}Fe{sub 0.1})O ferropericlase to 81.2 GPa at room temperature measured by Brillouin spectroscopy and X-ray diffraction in the diamond-anvil cell. Our data indicate that the spin transition of iron between 45 and 63 GPa dramatically affects the longitudinal and off-diagonal elements of the elastic stiffness tensor c{sub 11} and c{sub 12}, whereas it leaves the shear constant c{sub 44} almost unaffected. Based on our results, the spin transition markedly changes the pressure (and temperature) dependence of the compressional and bulk sound velocities and must be taken into account in any attempt to match average radial seismic velocity profiles with mineral physics observations. The different pressure dependence of compressional (and bulk) and shear sound velocities across the high-spin to low-spin (HS-LS) transition implies that the spin transition might be best observed in the v{sub p}/v{sub s} ratio and its pressure (and temperature) derivative. We also point out the possibility that the spin transition leads to an anti-correlated temperature dependence of shear and compressional wave speeds in certain pressure-temperature regimes in Earth's lower mantle.

58 GEOSCIENCES↗

TU-F-CAMPUS-J-03: Elasticity Functions Based On 4DCT Images to Predict Tumor and Normal Tissue Response to Radiation for Patients with Lung Cancers

Purpose: To investigate radiotherapy outcomes by incorporating 4DCT-based physiological and tumor elasticity functions for lung cancer patients. Methods: 4DCT images were acquired from 28 lung SBRT patients before radiation treatment. Deformable image registration (DIR) was performed from the end-inhale to the end-exhale using a B-Spline-based algorithm (Elastix, an open source software package). The resultant displacement vector fields (DVFs) were used to calculate a relative Jacobian function (RV) for each patient. The computed functions in the lung and tumor regions represent lung ventilation and tumor elasticity properties, respectively. The 28 patients were divided into two groups: 16 with two-year tumor local control (LC) and 12 with local failure (LF). The ventilation and elasticity related RV functions were calculated for each of these patients. Results: The LF patients have larger RV values than the LC patients. The mean RV value in the lung region was 1.15 (±0.67) for the LF patients, higher than 1.06 (±0.59) for the LC patients. In the tumor region, the elasticity-related RV values are 1.2 (±0.97) and 0.86 (±0.64) for the LF and LC patients, respectively. Among the 16 LC patients, 3 have the mean RV values greater than 1.0 in the tumors. These tumors were located near the diaphragm, where the displacements are relatively large.. RV functions calculated in the tumor were better correlated with treatment outcomes than those calculated in the lung. Conclusion: The ventilation and elasticity-related RV functions in the lung and tumor regions were calculated from 4DCT image and the resultant values showed differences between the LC and LF patients. Further investigation of the impact of the displacements on the computed RV is warranted. Results suggest that the RV images might be useful for evaluation of treatment outcome for lung cancer patients.

60 APPLIED LIFE SCIENCES↗