Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELASTIC MODULUS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Influence of the - phase separation on the tensile properties of Fe-base ODS PM 2000 alloy

The yield and ultimate tensile strengths of an ultrafine grained, oxide dispersion strengthened (ODS) PM 2000 alloy increased during aging at 475 C. Atom probe tomography and X-ray diffraction analysis revealed that the decrease in lattice parameter and the increases in the yield and ultimate tensile strengths were correlated with phase separation into Fe-rich {alpha} and Cr-enriched {alpha}{prime} phases. The lattice misfit between the emerging {alpha} and {alpha}{prime} domains and the resulting elastic strain, and the increment of the elastic modulus with aging time due to the corresponding decrease of lattice parameter during {alpha}-{alpha}{prime} phase separation, can be regarded as the main causes of hardening.

36 MATERIALS SCIENCE↗

Residual stress within nanoscale metallic multilayer systems during thermal cycling

Projected applications for nanoscale metallic multilayers will include wide temperature ranges. Since film residual stress has been known to alter system reliability, stress development within new film structures with high interfacial densities should be characterized to identify potential long-term performance barriers. To understand factors contributing to thermal stress evolution within nanoscale metallic multilayers, stress in Cu/Nb systems adhered to Si substrates was calculated from curvature measurements collected during cycling between 25 °C and 400 °C. Additionally, stress within each type of component layers was calculated from shifts in the primary peak position from in-situ heated X-ray diffraction. The effects of both film architecture (layer thickness) and layer order in metallic multilayers were tracked and compared with monolithic Cu and Nb films. Analysis indicated that the thermoelastic slope of nanoscale metallic multilayer films depends on thermal expansion mismatch, elastic modulus of the components, and also interfacial density. The layer thickness (i.e. interfacial density) affected thermoelastic slope magnitude while layer order had minimal impact on stress responses after the initial thermal cycle. When comparing stress responses of monolithic Cu and Nb films to those of the Cu/Nb systems, the nanoscale metallic multilayers show a similar increase in stress above 200 °C to the Nb monolithic films, indicating that Nb components play a larger role in stress development than Cu. Local stress calculations from X-ray diffraction peak shifts collected during heating reveal that the component layers within a multilayer film respond similarly to their monolithic counterparts.

36 MATERIALS SCIENCE↗

Investigation of specimen size effects by in-situ microcompression of equal channel angular pressed copper

Here, micropillar compression testing was implemented on Equal Channel Angular Pressed copper samples ranging from 200 nm to 10 µm in side length in order to measure the mechanical properties yield strength, first load drop during plastic deformation at which there was a subsequent stress decrease with increasing strain, work hardening, and strain hardening exponent. Several micropillars containing multiple grains were investigated in a 200 nm grain sample. The effective pillar diameter to grain size ratios, D/d , were measured to be between 1.9 and 27.2. Specimens having D/d ratios between 0.2 and 5 were investigated in a second sample that was annealed at 200 °C for 2 h with an average grain size of 1.3 µm. No yield strength or elastic modulus size effects were observed in specimens in the 200 nm grain size sample. However work hardening increases with a decrease in critical ratios and first stress drops occur at much lower stresses for specimens with D/d ratios less than 5. For comparison, bulk tensile testing of both samples was performed, and the yield strength values of all micropillar compression tests for the 200 nm grained sample are in good agreement with the yield strength values of the tensile tests.

36 MATERIALS SCIENCE↗

Deformation mechanisms in single crystal Ni-based concentrated solid solution alloys by nanoindentation

Nanoindentation is a critical technique to probe mechanical properties at the micrometer and sub-micrometer scales, accompanied by challenges from indentation size effect, pile-up/sink-in effect, and strain rate sensitivity. In this work, different nanoindentation techniques have been employed to explore Ni-based concentrated solid solution alloys (CSAs) with the addition of 3d transition metal elements including Co, Cr, Mn, and Fe, including unique single-crystal Ni, NiCo, NiFe, Ni 80 Cr 20 , and NiCoFeCr samples with (100) surfaces. A procedure of nanoindentation tests and data analysis/correction have been developed, and a data set of hardness, elastic modulus, strain rate sensitivity, and activation volume for Ni-based CSAs are provided, including the less explored binary alloys such as Ni 80 Cr 20 and Ni 80 Mn 20 . The results show that the type of alloying elements is more critical than the number of elements in strengthening: Co does not provide strengthening in NiCo, while Cr, Mn, and Fe are effective strengthening elements. Cr is the most effective among all the 3d transition metal elements. Furthermore, atomic-level lattice distortion is responsible for the strengthening and the role of stacking fault energy is insignificant in Ni-based CSAs at room temperature. In summary, nanoindentation shows increasing promise as a reliable and fast tool to provide comprehensive mechanical information for new alloy design and development.

36 MATERIALS SCIENCE↗

Diamond under extremes

Diamond is, by virtue of the covalent bonding between atoms and the very strong carbon to carbon bonds, the hardest natural material. It has been a fascinating material since its discovery, first as a decorative gem and more recently, for its numerous industrial uses because of its extreme hardness, elastic modulus, and optical transparency. In recent years, it has become a preferred ablator for laser shock experiments, and this has led to its choice as the capsule material for fusion experiments at the National Ignition Facility. Further, this review covers both experimental and computational (including machine learning) advancements in research on diamond subjected extreme conditions of temperature and pressure. The synergy between shock and ramp loading experiments and atomic level simulations is proving to be powerful in advancing our understanding of diamond under extremes.

36 MATERIALS SCIENCE↗

Modeling the interfacial failure and resulting mechanical properties of z-pinned additively manufactured composites

The mechanical properties of Fused Filament Fabrication (FFF) parts are limited in the build direction, albeit advantages such as design flexibility and in-house customization. Here, in this paper, a novel z-pinning approach that enhances mechanical properties in the build direction by depositing material across multiple layers within the part was investigated through numerical simulations and validated experimentally. A finite element model for z-pinned composite structures was developed by assigning fiber-orientation dependent material properties obtained using a micromechanics approach to beads and pins. The bead-to-bead and pin-to-pin adhesions within the z-pinned structures were modeled using a cohesive traction separation law. The properties of cohesive elements for carbon fiber-reinforced polylactic acid (CF-PLA) z-pinned composites were calibrated using tensile experiments. The elastic modulus and tensile strength of CF-PLA z-pinned composites in the build direction were predicted with the developed numerical model. The numerical investigation on various geometrical parameters revealed that the largest pin volume increases the stiffness and tensile strength by 40% and thus, has the greatest influence on the mechanical properties of the z-pinned composites. The effect of z-pin geometrical parameters on the mechanical properties was summarized to aid in the design of z-pinned additively manufactured composite structures.

36 MATERIALS SCIENCE↗

Degradation of different elastomeric polymers in simulated geothermal environments at 300°C

This study evaluates the degradation of six different elastomeric polymers used for O-rings: EPDM, FEPM, type I- and II-FKM, FFKM, and FSR, in five different simulated geothermal environments at 300 °C: 1) non-aerated steam/cooling cycles, 2) aerated steam/cooling cycles, 3) water-based drilling fluid, 4) CO 2 -rich geo-brine fluid, and, 5) heat–cool water quenching cycles. The factors assessed included the extent of oxidation, changes in thermal behavior, micro-defects, permeation of ionic species from the test environments into the O-rings, silicate-related scale-deposition, and changes in the O-rings' elastic modulus. The reliability of the O-rings to maintain their integrity depended on the elastomeric polymer composition and the exposure environment. FSR disintegrated while EPDM was oxidized only to some degree in all the environments, FKM withstood heat-water quenching but underwent chemical degradation, FEPM survived in all the environments with the exception of heat-water quenching where it underwent severe oxidation-induced degradation, and FFKM displayed outstanding compatibility with all the tested environments. This study discusses the degradation mechanisms of the polymers under the aforementioned conditions.

15 GEOTHERMAL ENERGY↗

Synthesis, spinning, and properties of very high molecular weight poly(acrylonitrile- co -methyl acrylate) for high performance precursors for carbon fiber

In this paper, synthesis of very high molecular weight (VHMW) polyacrylonitrile- co -methyl acrylate(PAN-co-MA) polymers with weight average molecular weights of at least 1.7 million g/mole were repeatedly achieved on a laboratory scale using emulsion polymerization. Furthermore, the development of a hybrid dry-jet gel solution spinning technique for the VHMW PAN-co-MA enabled continuous spinning of 100 filament count tows, 100s of meters in length. Single filaments were analyzed and tested for tensile performance. Experimentally, the hybrid spinning method coupled with VHMW polymers produced precursor fibers with excellent tensile properties, averaging 954 MPa in strength and 15.9 GPa in elastic modulus ( N = 296), with small filament diameters (5 μm). Results indicate a strong correlation between decreasing filament diameter, facilitated by high molecular weight polymer, and exponentially increasing tensile properties, using a hybrid dry-jet gel spinning process.

36 MATERIALS SCIENCE↗

The deformation and failure response of closed-cell PMDI foams subjected to dynamic impact loading

The present work aims to investigate the bulk deformation and failure response of closed-cell Polymeric Methylene Diphenyl Diisocyanate (PMDI) foams subjected to dynamic impact loading. First, foam specimens of different initial densities are examined and characterized in quasi-static loading conditions, where the deformation behavior of the samples is quantified in terms of the compressive elastic modulus and effective plastic Poisson's ratio. Then, the deformation response of the foam specimens subjected to direct impact loading is examined by taking into account the effects of material compressibility and inertia stresses developed during deformation, using high speed imaging in conjunction with 3D digital image correlation. The stress-strain response and the energy absorption as a function of strain rate and initial density are presented and the bulk failure mechanisms are discussed. As a result, it is observed that the initial density of the foam and the applied strain rates have a substantial influence on the strength, bulk failure mechanism and the energy dissipation characteristics of the foam specimens.

36 MATERIALS SCIENCE↗

Effects of fabric architectures on mechanical and damage behaviors in carbon/epoxy woven composites under multiaxial stress states

The mechanical properties and damage evolutions of carbon/epoxy woven fabric composites with three different fabric architectures, including one plain weave and two twill weave patterns, are experimentally investigated under multiaxial stress states. In particular, the effects of weave patterns are investigated by monotonic and cyclic off-axis tension tests. Both elastic modulus and strength degrade remarkably with increasing off-axis loading angle, while Poisson's ratio is much higher than that measured from on-axis tests and increases with loading strain gradually. Different fabric architectures show limited effects on the modulus and strength under multiaxial stress states, and they are well predicted by transformation equation and Tsai-Wu failure criteria, respectively. However, significantly different failure behaviors are observed in three fabric composites, and microstructure observation shows that fabric architecture affects the stress concentration and the damage development. Smaller crimp ratio and compacted structure postpone the damage development but result in more abrupt failure under multiaxial stress states.

36 MATERIALS SCIENCE↗

Composite binder, processing, and particle size effects on mechanical properties of non-hazardous high explosive surrogates

Plastic-bonded explosives (PBX) are polymer matrix composites that are highly loaded with micron-scale explosive crystals. The thermal and mechanical properties of these materials must be well-understood so that appropriate engineering models can be developed, but testing such properties under many scenarios can be hazardous and expensive. A non-hazardous PBX surrogate (“mock”) may be used in place of a PBX in many experiments if the thermomechanical properties are well-matched. Our previous research has shown that 5-iodo-2'-deoxyuridine (IDOX) is a promising crystalline filler material for the explosive cyclotetramethylene-tetranitramine (HMX). In this study, we investigate how the binder composition, variations in the IDOX particle size distribution, and pressing temperature affect the compressive strength and elastic modulus. We observe that while the binder system used in the composite dominates the mechanical response, the particle size distribution and pressing conditions do have a measurable effect on the material compliance and strength.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Characterization of hot-pressed von Alpen type NASICON ceramic electrolytes

The Na-ion conducting solid electrolyte NASICON is a promising solid state electrolyte (SSE) for use in Na based electrochemical systems. The effects of particle morphology and synthesis of von Alpen type NASICON via hot-pressing were investigated. Spray dried particles were shown to improve mechanical and electrochemical properties. X-ray diffraction, scanning electron microscopy, impulse excitation measurements, Vickers hardness, and impedance spectroscopy were used to correlate relationships between phase purity, microstructure, mechanical properties, and electrochemical properties. Scanning electron microscopy showed the presence of a glass phase as between 19.08% and 28.23% area percentage and a ZrO 2 phase between 0.46% and 3.51% area percentage in the hot-pressed samples. Impulse excitation showed elastic modulus varying from 83.65 to 97.65 GPa. The first values of Poisson's ratio and shear modulus of NASICON are reported as between 0.23 and 0.26 and 33.87 to 38.79 GPa, respectively. Vickers hardness and fracture toughness measurements showed Vickers hardness ranging from 4.30 to 4.68 GPa and fracture toughness ranging from 1.05 to 1.09 MPa m ½ . Impedance spectroscopy showed grain conductivities ranging from 1.023 to 1.287 mS/cm, with grain boundary resistance percentages between 73.22 and 47.5%. Total conductivities ranged from 0.292 to 0.596 mS/cm, with 0.596 mS/cm being achieved at room temperature for the spray dried powders with lower grain boundary resistance percentages.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Correlating high temperature mechanical and tribological properties of CrAlN and CrAlSiN hard coatings

CrAlN and CrAlSiN hard coatings deposited by magnetron sputtering were analyzed for their high temperature mechanical and tribological properties. High temperature nanoindentation measurements on both coatings were performed from room temperature up to 700 °C in steps of 100 °C where a reduction in hardness H and elastic modulus E* from their initial values was noticed. In addition, high temperature tribological tests were conducted in inert atmosphere in the same temperature range to obtain information about the coefficient of friction and the wear coefficient. In order to link the tribological behavior to the obtained mechanical properties, the H/E* ratio was calculated and compared to the high temperature wear from the current and other studies with similar coatings. Finally, the evolution of the mechanical and tribological properties at high temperature is discussed based on the current knowledge available in literature.

Drnovšek, Aljaž↗

Strength characterization of solar-synthesized cylindrical graphite carbon–carbon composites

The present work describes a new morphology of cylindrical graphite synthesized in a unique manner by direct solar decomposition of methane and reports the mechanical properties of its manifestation in woven carbon–carbon composites. Whereas traditional carbon–carbon composites are formed via epoxy impregnation, the deposited material in the process presented here conformally follows the existing shape and orientation of individual carbon fibers. Through this process, cylindrical graphite fibers are synthesized that possess superior strength due to their graphitic layers that amalgamate into interlocked pathways between disparate fibers. Here, strength measurements, taken in tandem with Raman, XRD, and SEM, paint a picture of the shift from cloth to composite behavior via graphitization of the original substrate combined with sheets of graphene coalescing into a unified composite, with a notable improvement in elastic modulus from 0.19 to 2.66 GPa.

Carbon–carbon composite↗

Mechanical characterization of Lipon films using nanoindentation

Nanoindentation has been used to characterize the elastic modulus and hardness of LiPON films ranging in thickness from 1 to 10 m. Four fully dense, amorphous films were deposited on glass and sapphire substrates with one film annealed at 200 C for 20 min. The modulus of LiPON is found to be approximately 77 GPa, and argued to be independent of the substrate type, film thickness, and annealing. Based on the numerical analysis of Monroe and Newman, this value may be sufficiently high to mechanically suppress dendrite formation at the lithium/LiPON interface in thin film batteries [1]. Using Sneddon's stiffness equation and assuming the modulus is 77 GPa, the hardness is found to be approximately 3.9 GPa for all but the annealed film. The hardness of the annealed film is approximately 5% higher, at 4.1 GPa. Atomic force microscopy images of the residual hardness impressions confirm the unexpected increase in hardness of the annealed film. Surprisingly, the indentation data also reveal time-dependent behavior in all four films. This indicates that creep may also play a significant role in determining how LiPON responds to complex loading conditions and could be important in relieving stresses as they develop during service.

36 MATERIALS SCIENCE↗