Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Direct simulation Monte Carlo”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Cloud Thickness from Diffusion of Lidar Pulses in Clouds

Measurements of the distribution of reflected light from a laser beam incident on an aqueous suspension of particles or "cloud" with known thickness and particle size distribution are reported. The distribution is referred to as the "cloud radiative Green's function", G. In the diffusion domain, G is sensitive to cloud thickness, allowing that important quantity to be retrieved. The goal of the laboratory simulation is to provide preliminary estimates of sensitivity of G to cloud thickness,for use in the optimal design of an offbeam Lidar instrument for remote sensing of cloud thickness (THOR, Thickness from Offbeam Returns). These clouds of polystyrene microspheres suspended in water are analogous to real clouds of water droplets suspended in air. The microsphere size distribution is roughly lognormal, from 0.5 microns to 25 microns, similar to real clouds. Density of suspended spheres is adjusted so mean-free-path of visible photons is about 10 cm, approximately 1000 times smaller than in real clouds. The light source is a ND:YAG laser at 530 nm. Detectors are flux and photon-counting Photomultiplier Tube (PMTS), with a glass probe for precise positioning. A Labview 5 VI controls positioning, and data acquisition, via an NI Motion Control board connected to a stepper motor driving an Edmund linear slider, and a 16-channel 16-bit NI-DAQ board. The stepper motor is accurate to 10 microns, and step size is selectable from the VI software. Far from the incident beam, the rate of exponential increase as the direction of the incident beam is approached scales as expected from diffusion theory, linearly with the cloud thickness, and inversely as the square root of the reduced optical thickness, and is independent of particle size. Near the beam the signal begins to increase faster than exponential, due to single and low-order scattering near the backward direction, and here the distribution depends on particle size. Results are being used to verify 3D Monte Carlo radiative transfer simulations, used to estimate signal-to-noise ratios for remotely sensed off beam returns, for both homogeneous and inhomogeneous clouds. Signal-to-noise estimates show that unfiltered observations are straight forward at night, while narrow band pass filters are being studied for day.

Cahalan, Robert F.↗
DOE OSTI2025

Estimating ionization states and continuum lowering from ab initio path integral Monte Carlo simulations for warm dense hydrogen

Warm dense matter (WDM) is an active field of research, with applications ranging from astrophysics to inertial confinement fusion. Ionization degree and continuum lowering are important quantities to understand how materials behave under these conditions, but can be difficult to diagnose since experimental campaigns are limited and often require model-dependent analysis. This is especially true for hydrogen, which has a comparably low scattering cross section, making high-quality data particularly difficult to obtain. Consequently, building equation of state tables often relies on simulations in combination with untested approximations to extract properties from experiments. Here, we investigate an approach for extracting the ionization potential depression and ionization degree—quantities which are otherwise not directly accessible from the physical model—from first-principles path integral Monte Carlo (PIMC) simulations utilizing a chemical model. In contrast to experimental measurements, where noise and nonequilibrium effects add to the uncertainty of the inferred parameters, PIMC simulations provide a clean signal with well-defined thermodynamic conditions. Comparisons against commonly used models show a qualitative agreement, but we find deviations primarily for the high-density and high-temperature cases. We also demonstrate the decreasing sensitivity of the dynamic structure factor with respect to both ionization and continuum lowering for increasing scattering angles in x-ray Thomson scattering experiments. Our work has important implications for the design of future experiments, but also offers qualitative understanding of structure factors and the imaginary-time correlation function obtained from first-principles quantum Monte Carlo simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1988

Modelling of SAR polarisation phase difference from trees

The data for polarization phase difference Delta Phi between the HH- and VV-polarized backscattered waves from tree-covered fields were obtained with an airborne synthetic aperture radar at 1.225 GHz. The mean values over tree-covered fields were derived from the images of the phase difference and were examined as a function of incident beam angle from 15 to 55 deg. A theoretical model for simulating these data, based on the electromagnetic wave scatterings from the tree trunk and its branches, both of which are assumed as very long dielectric cylinders was developed. The radius and direction of a tree branch are taken as random variables and are chosen by a Monte Carlo method to encounter the incident waves in producing the scattering events. The Monte Carlo simulated results are in good agreement with the observations within experimental uncertainty.

Mo, Tsan↗
DOE OSTI2022

A Framework to Analyze the Requirements of a Multiport Megawatt-Level Charging Station for Heavy-Duty Electric Vehicles

Widespread adoption of heavy-duty (HD) electric vehicles (EVs) will soon necessitate the use of megawatt (MW)-scale charging stations to charge high-capacity HD EV battery packs. Such a station design needs to anticipate possible station traffic, average and peak power demand, and charging/wait time targets to improve throughput and maximize revenue-generating operations. High-power direct current charging is an attractive candidate for MW-scale charging stations at the time of this study, but there are no precedents for such a station design for HD vehicles. We present a modeling and data analysis framework to elucidate the dependencies of a MW-scale station operation on vehicle traffic data and station design parameters and how that impacts vehicle electrification. This framework integrates an agent-based charging station model with vehicle schedules obtained through real-world vehicle telemetry data analysis to explore the station design and operation space. A case study applies this framework to a Class 8 vehicle telemetry dataset and uses Monte Carlo simulations to explore various design considerations for MW-scale charging stations and EV battery technologies. The results show a direct correlation between optimal charging station placement and major traffic corridors such as cities with ports, e.g., Los Angeles and Oakland. Corresponding parametric sweeps reveal that while good quality of service can be achieved with a mix of 1.2-megawatt and 100-kilowatt chargers, the resultant fast charging time of 35–40 min will need higher charging power to reach parity with refueling times.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRSDate not supplied

CFD2030 Grand Challenge: CFD-in-the-Loop Monte Carlo Simulation for Space Vehicle Design

Space vehicle design and certification differs widely from aircraft design relying more on probabilistic approaches than deterministic. Monte Carlo simulation plays an important role in the probabilistic design of space vehicles to ensure robust and reliable operation. Today, Monte Carlo flight simulation requires 1000’s of trajectory simulations that use databases to provide aerosciences models. These databases can be extremely expensive and time consuming to develop. Replacing these databases with unsteady computational fluid dynamics directly in the simulation loop has potential to significantly reduce the time required to analyze space vehicle concepts, improve simulation accuracy, and reduce the cost of space vehicle development. The CFD Vision 2030 Study outlined gaps and roadblocks to meeting the vision described in the study. The geometric, physical, and computational challenges associated with CFD-in-the-loop Monte Carlo simulation for space vehicle design are substantial and serve as an excellent grand challenge to advance the CFD 2030 vision.

CFD2030↗
NASA NTRS2011

Optimizing Muscle Parameters in Musculoskeletal Modeling Using Monte Carlo Simulations

Astronauts assigned to long-duration missions experience bone and muscle atrophy in the lower limbs. The use of musculoskeletal simulation software has become a useful tool for modeling joint and muscle forces during human activity in reduced gravity as access to direct experimentation is limited. Knowledge of muscle and joint loads can better inform the design of exercise protocols and exercise countermeasure equipment. In this study, the LifeModeler(TM) (San Clemente, CA) biomechanics simulation software was used to model a squat exercise. The initial model using default parameters yielded physiologically reasonable hip-joint forces. However, no activation was predicted in some large muscles such as rectus femoris, which have been shown to be active in 1-g performance of the activity. Parametric testing was conducted using Monte Carlo methods and combinatorial reduction to find a muscle parameter set that more closely matched physiologically observed activation patterns during the squat exercise. Peak hip joint force using the default parameters was 2.96 times body weight (BW) and increased to 3.21 BW in an optimized, feature-selected test case. The rectus femoris was predicted to peak at 60.1% activation following muscle recruitment optimization, compared to 19.2% activation with default parameters. These results indicate the critical role that muscle parameters play in joint force estimation and the need for exploration of the solution space to achieve physiologically realistic muscle activation.

Hanson, Andrea↗
DOE OSTI2025

Prediction of neutron production and energy spectrum by the inverse kinematic reaction between an incident 7 Li 3+ beam and a proton target in PHITS

A neutron source using the inverse kinematic reaction between lithium and proton, p( 7 Li, n) 7 Be, achieves forward-directed neutrons, potentially enhancing neutron yield in the forward direction. Despite the advantage, no evaluated-cross-section data for this reaction can be used in Monte Carlo simulation codes, such as PHITS. To solve this problem, this study aims to evaluate the applicability of the user-defined cross-section data, Frag data, for p ( 7 Li, n) 7 Be in PHITS. The simulations reproduced collisions between 7 Li 3+ ions and polypropylene targets. The Frag data was edited based on the JENDL-5 by utilizing the two-body collision kinematics. The neutron yield and angular distribution were investigated in the simulation. As a result, the forward neutron convergence with a reasonable neutron yield and energy spectrum was observed. The expected neutron yield in the forward 1-steradian area is 2.46 × 10 10 n/s when lithium-ion energy and current are 16.45 MeV and 0.1 mA.

43 PARTICLE ACCELERATORS↗
DOE OSTI2020

Effect of Confinement of SIA Cluster Diffusion by Impurities on Radiation Defect Accumulation due to 14MeV neutrons in Tungsten

Impurities acting as traps, reduce the self-interstitial atom (SIA) cluster mobility, thereby increasing recombination and in turn enhancing radiation-resistance of polycrystalline materials. However, at elevated temperatures, depending on SIA-trap (impurity) binding energy, SIA clusters may trap and detrap (detach) numerous times. In tungsten, SIA clusters of all sizes glide one-dimensionally (1D) along their Burgers vector direction. Hence, detrapped SIAs would retrace their path, confining their 1D-glide between traps. However, small SIA clusters can change the direction of their 1D-glide by overcoming a rotation barrier. In addition, impurities or solutes are known to reduce this barrier. A lower rotation barrier can result in detrapped SIA clusters that diffuse in a random 1D direction, effectively leading to 3D (net-3D) diffusion. Here we investigate the effect of two cases of SIA diffusion, namely confined-1D diffusion and net-3D diffusion, on the damage accumulation in polycrystalline tungsten under 14 MeV neutron irradiation using the object kinetic Monte Carlo method. Simulations were performed using cascade debris obtained from molecular dynamics simulations with primary knock-on atom (PKA) energies corresponding to 14 MeV neutrons. In the simulations with net-3D diffusion, SIA clusters of all sizes diffuse in a random 1D direction after the clusters detrap. While for the confined 1D diffusion case, SIA clusters larger than size 5 retain their original direction of 1D-glide. In both types of simulations, trapped vacancies are assumed to be permanently immobilized. Unexpectedly, the damage accumulation was lower with confined 1D diffusion than that with net-3D. We present a systematic comparison of the influence of the two cases of SIA diffusion on the radiation damage accumulation as a function of dose rate, detrapping barrier, and impurity concentration at 1025 K.

Accumulation and recovery of lattice damage, tungs↗
DOE OSTI2022

Modulation of intensity emerging from zero effort (MIEZE) with extended Fourier time at large scattering angle

Modulation of Intensity Emerging from Zero Effort (MIEZE) is a neutron resonant spin echo technique that allows one to measure time correlation scattering functions in materials by implementing radio-frequency (RF) intensity modulation at the sample and the detector. The technique avoids neutron spin manipulation between the sample and the detector and, thus, could find applications in cases where the sample depolarizes the neutron beam. However, the finite sample size creates a variance in the path length between the locations where scattering and detection happen, which limits the contrast in intensity modulation that one can detect, in particular, toward long correlation times or large scattering angles. We propose a modification to the MIEZE setup that will enable one to extend those detection limits to longer times and larger angles. Furthermore, we use Monte Carlo simulations of a neutron scattering beamline to show that by tilting the RF flippers in the primary spectrometer with respect to the beam direction, one can shape the wave front of the intensity modulation at the sample to compensate for the path variance from the sample and the detector. The simulation results indicate that this change enables one to operate a MIEZE instrument at much increased RF frequencies, thus improving the effective energy resolution of the technique. For the MIEZE instrument simulated, it shows that for an incident beam with the maximum divergence of 0.33°, the maximum Fourier time can be increased by a factor of 3.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Steady-state properties of multi-orbital systems using quantum Monte Carlo

A precise dynamical characterization of quantum impurity models with multiple interacting orbitals is challenging. In quantum Monte Carlo methods, this is embodied by sign problems. A dynamical sign problem makes it exponentially difficult to simulate long times. A multi-orbital sign problem generally results in a prohibitive computational cost for systems with multiple impurity degrees of freedom even in static equilibrium calculations. Here, we present a numerically exact inchworm method that simultaneously alleviates both sign problems, enabling simulation of multi-orbital systems directly in the equilibrium or nonequilibrium steady-state. The method combines ideas from the recently developed steady-state inchworm Monte Carlo framework [Erpenbeck et al., Phys. Rev. Lett. 130, 186301 (2023)] with other ideas from the equilibrium multi-orbital inchworm algorithm [Eidelstein et al., Phys. Rev. Lett. 124, 206405 (2020)]. We verify our method by comparison with analytical limits and numerical results from previous methods.

Chemistry↗
NASA NTRS1983

Gamma rays of 1-30 MeV from the Galactic Center Region

Preliminary results are reported for gamma rays from the Galactic Center Region at 1-30 MeV made with a balloon-borne double Compton scatter gamma ray telescope. The Compton scatter angle, energy, and arrival time of the incident gamma ray and direction of the Compton scattered secondary for downward-moving gamma rays were measured. The handling of the data is described, and the results of Monte Carlo simulation angular resolutions and absolute efficiencies for different zenith angles of incident gamma rays are given. A contour sky map of the weighted fluxes for a southern sky region is shown whose primary feature is a significant enhancement in the Galactic Center Region. It is concluded that several discrete sources contribute to broaden the maximum in the horizontal or RA direction. Less broadening is indicated along the galactic plane.

Oneill, T.↗
DOE OSTI2026

Modeling and Experimental Demonstration of Flux Spreading in Light Trapping Planar-Cavity Solar Enclosed Particle Receivers

This study experimentally validates and numerically models the flux-spreading effect in a light-trapping planar-cavity solar receiver) for particle-based concentrating solar power systems. The receiver's shallow cavity with vertical planar walls redistributes concentrated solar flux, reducing peak intensity and achieving uniform heat flux. On-sun tests at National Renewable Energy Laboratory's High-Flux Solar Furnace under flux up to 1500 kW/m2 measured cavity wall temperatures, which were compared with Monte Carlo ray-tracing (SolTrace) and computational numerical simulations. Three angular absorptance models were evaluated: constant absorptance, a Pyromark-based directional model, and a Fresnel-based Cr2O3 model. The Fresnel-derived model showed the best agreement with experiments, achieving high correlation (PC > 0.85), structural similarity (SSIM > 0.98), and signal-to-noise ratios (PSNR > 40 dB), with temperature prediction errors of 1-11%. Results confirm that flux spreading mitigates local overheating and validate the integrated modeling approach, supporting the solar receiver scalability for high-efficiency, high-temperature concentrating solar power applications.

14 SOLAR ENERGY↗
DOE OSTI2026

CADIS and FW-CADIS Variance Reduction in Gamma Transport for Predicting Prompt Forensics Signatures

The goal of prompt nuclear forensics is to determine the characteristics of a nuclear detonation based on the signatures available almost immediately after the explosion. An important characteristic is the reaction time history (RTH), a measure of the device’s rate of neutron multiplication. The RTH can be estimated by observation of the gamma radiation emitted from the detonation, which can be detected directly or observed indirectly as Teller light. Gamma transport simulations used to predict these radiation fields are often modeled stochastically using the Monte Carlo N-Particle (MCNP) code, which can be a computationally demanding task due to the number of particle histories needed to achieve statistical convergence. In an attempt to improve the efficiency of these calculations, we evaluate two variance reduction techniques: Consistent Adjoint-Driven Importance Sampling (CADIS) and Forward-Weighted Consistent Adjoint-Driven Importance Sampling (FW-CADIS). These methods use a deterministically calculated adjoint flux to create weight windows and source biasing that guide MCNP sampling. We study the utility of CADIS and FW-CADIS for their use in MCNP gamma transport for nuclear forensics prediction simulations. Furthermore, the results demonstrate that both CADIS and FW-CADIS improve the accuracy for forensics-focused simulations, with CADIS being most beneficial in direct detection and FW-CADIS being ideal for computing a global Teller light source.

CADIS↗
DOE OSTI2022

Induced seismicity potential based on probabilistic geomechanics for the San Juan Basin CarbonSAFE project

Although geologic carbon sequestration projects have yet to induce — or may never induce — a damaging earthquake, experiences from other deep injection industries such as hydraulic fracturing, enhanced geothermal systems, and saltwater disposal suggest that effective quantitative seismic risk assessment is necessary for deep saline carbon capture and sequestration (CCS) projects. One such imminent CCS project is the San Juan Basin CarbonSAFE Phase III program. We use Monte Carlo probabilistic geomechanical analyses combined with observations of the geologic and operational parameters of the San Juan Basin site and suggest that this project is of low-induced seismic risk. The primary analysis is split into four sections. First, we assess the literature for faults and past seismicity, and at least five faulting scenarios are directly relevant. Second, we develop and calibrate an integrated earth model for the project site. Third, we perform Monte Carlo simulations that consider reasonable uncertainties of the geomechanical parameters. Of five tested faulting scenarios, only one presents high Coulomb failure functions, but fourth, we determine the risk to be low based on the combined lack of historical seismicity, the geologic framework of the faulting scenario, and the presence of saltwater injection at the same depth as the proposed supercritical carbon dioxide injection. The most sensitive parameters in the geomechanical calculations are the fault dip and the coefficient of friction. The least sensitive are the fault strike and the orientation of the maximum horizontal principal stress.

58 GEOSCIENCES↗
DOE OSTI2023

High Intensity Gamma Ray Source Scintillation Attenuation Spectrometer and Filter Stack Monoenergetic Calibration

The Laser-Based X-ray Radiographic Imaging team at Los Alamos National Lab is looking for a monoenergetic MeV X-ray source to both verify our Monte Carlo N-particle simulations of detector performance and calibrate the instruments for future measurements. Funded by the Laboratory Directed Research and Development (LDRD) program, our overall goal is to improve the radiographic quality and reliability of laser-based X-ray sources for deployment at both dynamic and static radiography facilities. Laser-based X-ray sources have demonstrated smaller spot sizes to current electron accelerator based sources. The smaller laser spot size leads to significantly improved resolution.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Interaction models and configurational entropies of binary MoTa and the MoNbTaW high entropy alloy

We introduce a simplified method to model the interatomic interactions of high entropy alloys based on a lookup table of cluster energies. Furthermore, these interactions are employed in replica exchange Monte Carlo simulations with histogram analysis to obtain thermodynamic properties across a broad temperature range. Kikuchi's cluster variation method entropy formalism is applied to directly calculate entropy from statistics on short- and long-range chemical order, and we discuss the convergence of the entropy as clusters of differing size are included. A high temperature series expansion aids in our understanding of the convergence. Computer codes implementing these methods, and supporting data, are freely available on the internet.

36 MATERIALS SCIENCE↗
NASA NTRS2012

Multi-Scale Modeling of Liquid Phase Sintering Affected by Gravity: Preliminary Analysis

A multi-scale simulation concept taking into account impact of gravity on liquid phase sintering is described. The gravity influence can be included at both the micro- and macro-scales. At the micro-scale, the diffusion mass-transport is directionally modified in the framework of kinetic Monte-Carlo simulations to include the impact of gravity. The micro-scale simulations can provide the values of the constitutive parameters for macroscopic sintering simulations. At the macro-scale, we are attempting to embed a continuum model of sintering into a finite-element framework that includes the gravity forces and substrate friction. If successful, the finite elements analysis will enable predictions relevant to space-based processing, including size and shape and property predictions. Model experiments are underway to support the models via extraction of viscosity moduli versus composition, particle size, heating rate, temperature and time.

Olevsky, Eugene↗
NASA NTRS1993

A theoretical and numerical study of polarimetric scattering and emission from random rough surfaces with anisotropic directional spectrum

In this paper, theoretical and numerical results of the polarimetric scattering and emission from random rough surfaces with anisotropic directional spectrum are presented for the remote sensing of ocean and soil surfaces. The polarimetric scattered field for rough dielectric surfaces is derived to the second order by the small perturbation method (SPM). It is found that the second-order scattered field is coherent in nature, and its coefficients for different polarizations present the lowest-order corrections to the Fresnel reflection coefficients of the surfaces. In addition, the cross-polarized (HV and VH) components of the coherent fields are reciprocal and not zero for surfaces with anisotropic directional spectrum when the azimuth angle of the incident direction is not aligned with the symmetry directions of surfaces. In order to verify the energy conservation condition of the theoretical results, which is important if the theory is to be applied to the passive polarimetry of rough surfaces, a Monte Carlo simulation is performed to numerically calculate the polarimetric reflectivities of one-dimensional random rough surfaces which are generated with a prescribed power-law spectrum in the spectral domain and transformed to the spatial domain by the FFT. The surfaces simulated by this approach are periodic with the period corresponding to the low-wavenumber cutoff. To calculate the scattering from periodic dielectric surfaces, the authors present a new numerical technique which applies the Floquet theorem to reduce the problem to one period and does not require the evaluation of one-dimensional periodic Green's function used in the conventional method of moment formulation. Once the scattering coefficients are obtained, the polarimetric Stokes vectors for the emission from the random surfaces are then calculated according to the Kirchhoff's law and are illustrated as functions of relative azimuth observation and row directions. The second-order SPM is also reduced to this one-dimensional case, and theoretical results for all four Stokes parameters are in excellent agreement with the numerical results obtained from the Monte Carlo simulation. Moreover, the second order coherent fields are found to be necessary for the theoretical evaluation of the third and fourth Stokes parameters. Without that, the reflectivities of random rough surfaces are significantly over-estimated, and the signs of the third and the fourth Stokes parameters are found to be incorrect, if calculated by using the first-order incoherent fields alone.

Yueh, S. H.↗