Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DRAG”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Flight and wind tunnel investigation of the effects of Reynolds number on installed boattail drag at subsonic speeds

A flight and wind tunnel investigation was conducted to determine the effects of Reynolds number on the installed boattail drag of an underwing nacelle. Tests were run on a modified F-106B aircraft and 0.05 and 0.22 scale wind tunnel models. Tests were conducted at Mach numbers of 0.6 and 0.9 and over a 16 to 1 range of Reynolds numbers. Highest drag was obtained at intermediate Reynolds numbers corresponding to about the lowest flight values and that of the 0.22 scale model. Significantly lower drag was obtained at both higher and lower Reynolds numbers.

Chamberlin, R.↗
NASA NTRS1973

The effects on cruise drag of installing refan-engine nacelles on the McDonnell-Douglas DC-9

A high speed wind tunnel test has been conducted to determine the effect on cruise drag for installing larger JT8D Refan engine nacelles on the Douglas DC-9. Drag data and wing- and nacelle/pylon/fuselage-channel pressure data are presented. Reduced pylon spares, required to minimize effects of the nacelle installation on low-speed deep stall, were investigated. The reduce span pylons resulted in no adverse interference effects. At typical cruise Mach numbers the measured penalty for the Refan installation was less than estimated due to a favorable effect of the larger entering engine stream tube suppressing the wing upper-surface velocities with subsequent wing compressibility drag reduction. Channel pressures show no shock waves or boundary layer separations.

Callaghan, J. T.↗
NASA NTRS1973

Flight and wind tunnel investigation of the effects of Reynolds number on installed boattail drag at subsonic speeds.

A flight and wind tunnel investigation was conducted to determine the effects of Reynolds number on the installed boattail drag of an underwing nacelle. Tests were run on a modified F-106B aircraft and 0.05 and 0.22 scale wind tunnel models. Tests were conducted at Mach numbers of 0.6 and 0.9 and over a 16 to 1 range of Reynolds numbers. Highest drag was obtained at intermediate Reynolds numbers corresponding to about the lowest flight values and that of the 0.22 scale model. Significantly lower drag was obtained at both higher and lower Reynolds numbers.

Chamberlin, R.↗
NASA NTRS1974

Drag reduction obtained by rounding vertical corners on a box-shaped ground vehicle

A box-shaped ground vehicle was used to simulate the aerodynamic drag of delivery vans, trucks, and motor homes. A coast-down method was used to define the drag of this vehicle in a configuration with all square corners and a modified configuration with the four vertical corners rounded. The tests ranged in velocity from 30 miles per hour to 65 miles per hour, and Reynolds numbers ranged from 4.4 x 1,000,000 to 1.0 x 10 to the 7th power based on vehicle length. The modified configuration showed a reduction in aerodynamic drag of about 40 percent as compared to the square cornered configuration.

Saltzman, E. J.↗
NASA NTRS1974

Drag and distribution measurements of single-element fuel injectors for supersonic combustors

The drag caused by several vortex generating fuel injectors for scramjet combustors was measured in a Mach 2 to 3.5 airstream. Injector drag was found to be strongly dependent on injector thickness ratio. The distribution of helium injected into the stream was measured both in the near field and the far field of the injectors for a variety of pressure ratios. The far field results differed appreciably from measurements in the near field. Injection pressure ratio was found to profoundly influence the penetration. One of the aerowing configurations tested yielded low drag consistent with desirable penetration and spreading characteristics.

Povinelli, L. A.↗
NASA NTRS1974

Reynolds number effects on boattail drag of exhaust nozzles from wind tunnel and flight tests

A family of nacelle mounted high angle boattail nozzles was tested to investigate Reynolds number effects on drag. The nozzles were flown on a modified F-106B and mounted on scale models of a F-106 in a wind tunnel. A 19- to 1-range of Reynolds number was covered as a result of the large size differences between models and by flying over a range of altitude. In flight, the nozzles were mounted behind J-85 turbojet engines. Jet boundary simulators and a powered turbojet engine simulator were used on the wind tunnel models. Data were taken at Mach numbers of 0.6 and 0.9. Boattail drag was found to be affected by boattail number. The effect is a complex relationship dependent upon boundary layer thickness and nozzle boattail shape. As Reynolds number was increased from the lowest values obtained with scale models, boattail drag first increased to a maximum at the lowest flight Reynolds number and then decreased.

Wilcox, F. A.↗
NASA NTRS1974

Erosion in radial inflow turbines. Volume 2: Balance of centrifugal and radial drag forces on erosive particles

The particle motion in two-dimensional free and forced inward flowing vortices is considered. A particle in such a flow field experiences a balance between the aerodynamic drag forces that tend to drive erosive particles toward the axis, and centrifugal forces that prevent these particles from traveling toward the axis. Results predict that certain sizes of particles will achieve a stable orbit about the turbine axis in the inward flowing free vortex. In this condition, the radial drag force is equal to the centrifugal force. The sizes of particles that will achieve a stable orbit is shown to be related to the gas flow velocity diagram at a particular radius. A second analysis yields a description of particle sizes that will experience a centrifugal force that is greater than the radial component of the aerodynamic drag force for a more general type of particle motion.

Clevenger, W. B., Jr.↗
NASA NTRS1974

Drag reductions obtained by modifying a box-shaped ground vehicle

A box-shaped ground vehicle was used to simulate the aerodynamic drag of high volume transports, that is, delivery vans, trucks, or motor homes. The coast-down technique was used to define the drag of the original vehicle, having all square corners, and several modifications of the vehicle. Test velocities ranged up to 65 miles per hour, which provided maximum Reynolds numbers of 1 times 10 to the 7th power based on vehicle length. One combination of modifications produced a reduction in aerodynamic drag of 61 percent as compared with the original square-cornered vehicle.

Saltzman, E. J.↗
NASA NTRS1974

Recent improvements in our knowledge of neutral atmosphere structure from satellite drag measurements

Observational results on the density in the thermosphere and lower exosphere (i.e., within the altitude range from about 150 to about 1000 km) are discussed in this paper. Most observational results on total gas density were obtained from orbital drag and more recently also from in-situ drag analysis. The primary parameter measured is atmospheric density, with temperature as a secondary structural parameter deduced with the help of theory and/or atmospheric models. Both the merits and shortcomings of the drag analysis method are outlined in view of a comparison of temperature deduced from total density and kinetic gas temperature measured by incoherent scatter. Recent improvements of our knowledge of the known density variations are presented.

Roemer, M.↗
NASA NTRS1974

Reynolds number effects on boattail drag of exhaust nozzles from wind tunnel and flight tests

A family of nacelle-mounted high-angle boattail nozzles was tested to investigate Reynolds number effects on drag. The nozzles were flown on a modified F-106B and mounted on scale models of an F-106 in a wind tunnel. A 19-to-1 range of Reynolds number was covered as a result of the large size differences between models and by flying over a range of altitude. In flight the nozzles were mounted behind J-85 turbojet engines. Jet boundary simulators and a powered turbojet engine simulator were used on the wind tunnel models. Data were taken at Mach numbers of 0.6 and 0.9. Boattail drag was found to be affected by Reynolds number. The effect is a complex relationship dependent upon boundary layer thickness and nozzle boattail shape. As Reynolds number was increased from the lowest values obtained with scale models, boattail drag first increased to a maximum at the lowest flight Reynolds number and then decreased.

Wilcox, F. A.↗
NASA NTRS1975

Reynolds number effects on boattail drag of exhaust nozzles from wind tunnel and flight tests

A family of nacelle mounted high angle boattail nozzles was tested to investigate Reynolds number effects on drag. The nozzles were flown on a modified F-106B and mounted on scale models of an F-106 in a wind tunnel. A 19- to 1-range of Reynolds number was covered as a result of the large size differences between models and by flying over a range of altitude. In flight the nozzles were mounted behind J-85 turbojet engines. Jet boundary simulators and a powered turbojet engine simulator were used on the wind tunnel models. Data were taken at Mach numbers of 0.6 and 0.9. Boattail drag was found to be affected by Reynolds number. The effect is a complex relationship dependent upon boundary layer thickness and nozzle boattail shape. As Reynolds number was increased from the lowest values obtained with scale models, boattail drag first increased to a maximum at the lowest flight Reynolds number and then decreased.

Wilcox, F. A.↗
NASA NTRS1975

A comprehensive plan for helicopter drag reduction

Current helicopters have parasite drag levels 6 to 10 times as great as fixed wing aircraft. The commensurate poor cruise efficiency results in a substantial degradation of potential mission capability. The paper traces the origins of helicopter drag and shows that the problem (primarily due to bluff body flow separation) can be solved by the adoption of a comprehensive research and development plan. This plan, known as the Fuselage Design Methodology, comprises both nonaerodynamic and aerodynamic aspects. The aerodynamics are discussed in detail and experimental and analytical programs are described which will lead to a solution of the bluff body problem. Some recent results of work conducted at the Naval Ship Research and Development Center (NSRDC) are presented to illustrate these programs. It is concluded that a 75-per cent reduction of helicopter drag is possible by the full implementation of the Fuselage Design Methodology.

Williams, R. M.↗
NASA NTRS1975

Techniques for determining propulsion system forces for accurate high speed vehicle drag measurements in flight

As part of a NASA program to evaluate current methods of predicting the performance of large, supersonic airplanes, the drag of the XB-70 airplane was measured accurately in flight at Mach numbers from 0.75 to 2.5. This paper describes the techniques used to determine engine net thrust and the drag forces charged to the propulsion system that were required for the in-flight drag measurements. The accuracy of the measurements and the application of the measurement techniques to aircraft with different propulsion systems are discussed. Examples of results obtained for the XB-70 airplane are presented.

Arnaiz, H. H.↗
NASA NTRS1975

General overview of drag

The state-of-the-art on aerodynamic drag reduction is briefly reviewed. The various elements making up the total drag of an aircraft include fuselage, wing, nacelles, trim, interference, tail, and cooling drag.

Anderson, S. A.↗
NASA NTRS1975

Summary of drag clean-up tests in NASA Langley full-scale tunnel

This summary of drag results presents tabulations on fighter aircraft and light twin general aviation aircraft wind tunnel tests. The figures show that the friction drag for light twins is larger than that for the fighters because of the greater wetted area and the smaller wing area used for reference. Full scale tunnel tests developed the following design features contributing to excessive drag: cooling flow system, engine exhaust stacks, landing gears, control surface gaps, and wing irregularities and leakages.

Mckinney, M. O.↗
NASA NTRS1975

Some comments on fuselage drag

The following areas relating to fuselage drag are considered: (1) fuselage fineness - ratio and why and how this can be selected during preliminary design; (2) windshield drag; (3) skin roughness; and (4) research needs in the area of fuselage drag.

Roskam, J.↗
NASA NTRS1975

Some methods for reducing wing drag and wing-Nacelle interference

Primary efforts directed toward drag reduction centered on the design of both supercritical and subcritical families of airfoils, the reduction of induced drag through the use of vortex diffusers, and the reduction of interference drag for executive-type aircraft.

Kelly, T. C.↗