Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Camber”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

The influence of leading-edge load alleviation on supersonic wing design

A theoretical and experimental program to assess the effect of leading-edge load constraints on wing design and performance was conducted. For a planform characterized by a highly swept leading edge on the inboard region, linear theory was used to design camber surfaces which produced minimum drag-due-to-lift at the design lift coefficient of 0.08 and a design Mach number of 2.4. In an effort to delay the formation of leading edge vortices which often occur on highly swept wings, two approaches were used in the design criteria to limit the loadings on the leading edge. One wing was constrained to have the normal Mach number less than one everywhere along the leading edge and the second wing was constrained to have a pressure coefficient of zero on the leading edge. Force tests were run on the two constrained wings, on a flat reference wing and on an optimized wing with no leading edge constraints. All wings had identical planforms and thicknesses and were tested over a range of Mach numbers from 1.8 to 2.8 and a range in angles of attack from -5 deg to 8 deg. A comparison of the experimental performance of these four models is shown. Correlations of these results with theoretical predictions and flow visualization photographs are also included.

Darden, C. M.↗
NASA NTRS1984

Numerical simulation of the tip vortex off a low-aspect-ratio wing at transonic speed

The viscous transonic flow around a low-aspect-ratio wing has been computed using an implicit, three-dimensional, 'thin-layer' Navier-Stokes solver. The grid around the geometry of interest is obtained numerically as a solution to a Dirichlet problem for the cube. The geometry chosen for this study is a low-aspect-ratio wing with large sweep, twist, taper, and camber. The topology chosen to wrap the mesh around the wing with good tip resolution is a C-O type mesh. Using this grid, the flow around the wing was computed for a free-stream Mach number of 0.82 at an angle of attack of 5 deg. At this Mach number, an oblique shock forms on the upper surface of the wing, and a tip vortex and three-dimensional flow separation off the wing surface are observed. Particle path lines indicate that the three-dimensional flow separation on the wing surface is part of the roots of the tip-vortex formation. The lifting of the tip vortex before the wing trailing edge is clearly observed by following the trajectory of particles released around the wing tip.

Mansour, N. N.↗
NASA NTRS1984

Engineering analysis of drooped leading-edge wings near stall

Numerical results obtained with a three-dimensional vortex panel computer program for the calculation of inviscid, incompressible (potential) flow over infinitely thin finite wings with camber are presented. The program, which is designed for wings with drooped leading edge discontinuities, is essentially a numerical representation of lifting surface theory, involving both spanwise and chordwise distributions of vorticity. The results also include two engineering approximations. First, the effect of the leading-edge discontinuities is modeled by assuming that the vortices emanating from the discontinuities aerodynamically divide the wing into three distinct sections of lower aspect ratio. Secondly, the effect of the separated flow at high angle of attack is modeled by applying rectangular vortex panels with a varying vortex strength over the portions of the wing with attached flow.

Anderson, J. D., Jr.↗
NASA NTRS1984

Wing design with attainable thrust considerations

A CAD process that includes leading-edge thrust considerations for wings with high aerodynamic efficiencies is outlined. Rectangular grids are used for evaluation of both subsonic and supersonic pressure loadings. Account is taken of the Mach number, Re, the wing planform, the presence of camber, the airfoil geometry and the locations and forces induced by shed vortices. Optimization techniques are applied to the candidate surfaces in order to consider the attainable thrust. Inclusion of the optimization techniques permits analyses of mission-adaptive wings and various flap systems and the elimination of singularities in the flight envelope.

Carlson, H. W.↗
NASA NTRS1984

Application of an optimization method to high performance propeller designs

The application of an optimization method to determine the propeller blade twist distribution which maximizes propeller efficiency is presented. The optimization employs a previously developed method which has been improved to include the effects of blade drag, camber and thickness. Before the optimization portion of the computer code is used, comparisons of calculated propeller efficiencies and power coefficients are made with experimental data for one NACA propeller at Mach numbers in the range of 0.24 to 0.50 and another NACA propeller at a Mach number of 0.71 to validate the propeller aerodynamic analysis portion of the computer code. Then comparisons of calculated propeller efficiencies for the optimized and the original propellers show the benefits of the optimization method in improving propeller performance. This method can be applied to the aerodynamic design of propellers having straight, swept, or nonplanar propeller blades.

Li, K. C.↗
NASA NTRS1984

An evaluation of the relative merits of wing-canard, wing-tail, and tailless arrangements for advanced fighter applications

Two sets of wind tunnel tests were performed to examine the relative merits of wing-canard, wing-tail and tailless configurations for advanced fighters. Both sessions focused on variable camber using automated, prescheduled leading and trailing edge flap positioning. The trials considered a modified F-16 tail and canard configuration at subsonic, transonic and supersonic speeds, a 60 deg delta wing sweep, a 44 deg leading edge trapezoidal wing at subsonic and supersonic speeds, vortex flow effects, and flow interactions in the canard-wing-tail-tailless variations. The results showed that large negative stabilities would need to be tolerated in wing-canard arrangements to make them competitive with wing-tail arrangements. Subsonic polar shapes for canard and tailless designs were more sensitive to static design margins than were wing-tail arrangements. Canards provided better stability at supersonic speeds. The static margin limits were a critical factor in control surface selection. Finally, a tailless delta wing configuration exhibited the lowest projected gross take-off weight and drag values.

Nicholas, W. U.↗
NASA NTRS1984

Incompressible lifting-surface aerodynamics for a rotor-stator combination

Current literature on the three dimensional flow through compressor cascades deals with a row of rotor blades in isolation. Since the distance between the rotor and stator is usually 10 to 20 percent of the blade chord, the aerodynamic interference between them has to be considered for a proper evaluation of the aerothermodynamic performance of the stage. A unified approach to the aerodynamics of the incompressible flow through a stage is presented that uses the lifting surface theory for a compressor cascade of arbitrary camber and thickness distribution. The effects of rotor stator interference are represented as a linear function of the rotor and stator flows separately. The loading distribution on the rotor and stator flows separately. The loading distribution on the rotor and stator blades and the interference factor are determined concurrently through a matrix iteration process.

Ramachandra, S. M.↗
NASA NTRS1984

Space Shuttle Orbiter trimmed center-of-gravity extension study. Volume 8: Effects of configuration modifications on the aerodynamic characteristics of the 140 A/B Orbiter at a Mach number of 5.97

Aerodynamic characteristics at M=5.97 for the 140 A/B Space Shuttle Orbiter configuration and for the configuration modified by geometric changes in the wing planform fillet region and the fuselage forebody are presented. The modifications, designed to extend the orbiter's longitudinal trim capability to more forward center of gravity locations, include reshaping the baseline wing fillet, changing the fuselage forebody camber, and adding canards. The Langley 20 inch Mach 6 Tunnel at a Reynolds number of approximately 6 million based on fuselage reference length was used. The angle of attack range of the investigation varied from about 15 deg to 35 deg at 0 deg and -5 deg sideslip angles. Data are obtained with the elevators and body flap deflected at appropriate negative and positive conditions to assess the trim limits.

Phillips, W. P.↗
NASA NTRS1985

Downwash in the plane of symmetry of an elliptically loaded wing

A closed-form solution for the downwash in the plane of symmetry of an elliptically loaded line is given. This theoretical result is derived from Prandtl's lifting-line theory and assumes that: (1) a three-dimensional wing can be replaced by a straight lifting line, (2) this line is elliptically loaded, and (3) the trailing wake is a flat-sheet which does not roll up. The first assumption is reasonable for distances greater than about 1 chord from the wing aerodynamic center. The second assumption is satisfied by any combination of wing twist, spanwise camber variation, or planform that approximates elliptic loading. The third assumption is justified only for high-aspect-ratio wings at low lift coefficients and downstream distances less than about 1 span from the aerodynamic center. It is shown, however, that assuming the wake to be fully rolled up gives downwash values reasonably close to those of the flat-sheet solution derived in this paper. The wing can therefore be modeled as a single horseshoe vortex with the same lift and total circulation as the equivalent ellipticity loaded line, and the predicted downwash will be a close approximation independent of aspect ratio and lift coefficient. The flat-sheet equation and the fully rolled up wake equation are both one-line formulas that predict the upwash field in front of the wing, as well as the downwash field behind it. These formulas are useful for preliminary estimates of the complex aerodynamic interaction between two wings (i.e., canard, tandem wing, and conventional aircraft) including the effects of gap and stagger.

Phillips, J. D.↗
NASA NTRS1985

The application of some lifting-body reentry concepts to missile design

The aerodynamic characteristics of some lifting-body concepts are examined with a view to the applicability of such concepts to the design of missiles. A considerable amount of research has been done in past years with vehicle concepts suitable for manned atmospheric-entry and atmospheric flight. Some of the concepts appear to offer some novel design approaches for missiles for a variety of missions and flight profiles, including long-range orbital/reentry with transatmospheric operation for strategic penetration, low altitude penetration, and battlefield tactical. The concepts considered include right triangular pyramidal configurations, a lenticular configuration, and various 75-degree triangular planform configurations with variations in body camber and control systems. The aerodynamic features are emphasized but some observations are also made relative to other factors such as heat transfer, structures, carriage, observability, propulsion, and volumetric efficiency.

Spearman, M. L.↗
NASA NTRS1985

Effect of leading-edge load constraints on the design and performance of supersonic wings

A theoretical and experimental investigation was conducted to assess the effect of leading-edge load constraints on supersonic wing design and performance. In the effort to delay flow separation and the formation of leading-edge vortices, two constrained, linear-theory optimization approaches were used to limit the loadings on the leading edge of a variable-sweep planform design. Experimental force and moment tests were made on two constrained camber wings, a flat uncambered wing, and an optimum design with no constraints. Results indicate that vortex strength and separation regions were mildest on the severely and moderately constrained wings.

Darden, C. M.↗
NASA NTRS1984

Airfoil trailing edge flow measurements and comparison with theory, incorporating open wind tunnel corrections

Trailing edge data for boundary layer-near wake thickness parameters are given for airfoils and flat plates. Reynolds number effects are examined as a function of model size, velocity and boundary layer tripping. These data expand that presented previously by the authors particularly for airfoil non-zero angles of attack. Comparisons are made here with boundary layer calculations using potential flow modeling and a well documented two-dimensional finite-difference method for laminar and turbulent boundary layers. Open wind tunnel corrections to angle of attack and camber are developed and are incorporated in the potential flow modeling to assure correct comparisons for non-zero angles of attack. It was found that although the open tunnel flow turbulence affected boundary layer transition for the higher velocities the theory successfully 'brackets' the data. Comparisons demonstrate the degree of accuracy one might expect for the prediction of boundary layer thickness parameters when given only geometry and nominal flow conditions as input to boundary layer codes.

Brooks, T. F.↗
NASA NTRS1984

Design parameters for flow energizers

One of the most significant uses of flow energizers, which are small highly swept strakes mounted immediately above a lifting surface, is in flow control over regions where a lifting surface is joined to another body, such as a fuselage or nacelle. In the presently reported systematic wind tunnel test study of flow energizers, 14 different geometric configurations using a 75-deg sweep flow energizer were tested on a light twin-engine general aviation aircraft model. It is found that cambered flow energizers perform better than their flat counterparts. All but two of the energizer installations developed lower L/D at cruise angles of attack, lower maximum lift coefficients, and lower stall angles of attack than the baseline model.

Ward, D. T.↗
NASA NTRS1985

A vortex-lattice method for general, unsteady aerodynamics

A general method of calculating unsteady, incompressible, inviscid, three-dimensional flows around arbitrary planforms has been developed. The method is an extension of the vortex-lattice technique. It is not limited by aspect ratio, camber, or angle of attack, as long as vortex breakdown does not occur above the surface of the wing and separation occurs only along sharp edges. As the wing performs arbitrary maneuvers, the position of the wake and the distribution of circulation on the wing and in the wake are obtained as functions of time. One desirable feature of the present method is its ability to treat steady lifting flows very efficiently. Several examples of steady and unsteady flows are presented. These include rectangular wings, with and without flaps, delta, and cropped delta wings.

Konstadinopoulos, P.↗
NASA NTRS1985

Three-dimensional inviscid flow analysis of turbofan forced mixers

A three-dimensional potential analysis has been formulated and applied to the inviscid flow over a turbofan forced mixer. The method uses a unique small disturbance formulation to analytically uncouple the circumferential flow from the radial and axial flow problem, thereby reducing the analysis to the solution of a series of axisymmetric problems. These equations are discretized using a flux volume formulation along a Cartesian grid. The method extends earlier applications of the Cartesian method to complex cambered geometries. The effects of power addition are also included within the potential formulation. Good agreement is obtained with an alternate small disturbance analysis for a symmetric mixer in a planar duct. In addition calculations showing pressure distributions and induced secondary vorticity fields are presented for practical turbofan mixer configurations, and where possible, comparison has been made with available experimental data.

Barber, T. J.↗
NASA NTRS1985

Three dimensional aerodynamics of an annular cascade in a non-uniform inlet flow

Three-dimensional viscous and inviscid numerical analyses are currently being developed to predict the complex flow through turbomachine blade passages. To be of value to the designer, these numerical solutions must be evaluated and subsequent refinements directed by correlating predicted flow fields with data obtained from experiments which model the fundamental three-dimensional flow phenomena inherent in blade rows. This paper describes a series of experiments to provide such data. In particular, the effect of a potential and a rotational inlet flow field on the detailed three-dimensional aerodynamic performance of an extensively instrumented cambered airfoil cascade has been determined at two levels of aerodynamic loading. Data presented quantify the pressure and suction surface static pressure chordwise distributions on the hub, mean, and tip streamlines; the velocity distribution in the cascade aft-passage region; and the cascade exit region flow field. Appropriate data are correlated with predictions.

Manwaring, S. R.↗
NASA NTRS1985

Prediction of HiMAT RPRV component interference effects at transonic speeds

Detailed surface flow field analyses of the NASA Highly Maneuverable Aircraft Technology Remotely Piloted Research Vehicle (HiMAT RPRV) are described. Computational predictions are provided by a nonlinear finite difference transonic wing-body code. Component interference effects are obtained through modifications in lifting surface twist and camber boundary conditions. Complex aircraft interactions created by wing-tip fins, landing gear, and lower surface wing actuator fairings are included. Lifting surface viscous flow effects are modeled using a two-dimensional 'strip' boundary layer method. Correlations with flight test data presented demonstrate the high degree of accuracy achieved for this realistic aircraft configuration. This methodology and approach appears to be generally applicable to other multisurface configurations.

Laiosa, J.↗
NASA NTRS1985

Subsonic pressure distributions near a wing-fin juncture on a supersonic arrow-wing configuration with wing-mounted vertical fins

A generic supersonic arrow-wing configuration has been extensively studied to develop a consistent experimental data base to aid in verifying analytical prediction methods. One of the wing configurations studied was a twisted and cambered wing with wing-mounted vertical fins and trailing-edge flaps. The pressure data obtained on that configuration was limited in the wing-fin juncture region, and no pressures were obtained on the fin itself. However, detailed data in the juncture region and on the fin are essential to check out the analytical prediction methods. Therefore, the model was modified to provide details of the juncture pressure field as well as pressures on the fin. The results of this experimental investigation showed that the addition of a fin helped improve the wing pressure distribution outboard of the fin. Deflection of the trailing-edge flap did not adversely affect this trend. The pressure distributions on the vertical fin were generally affected more by change in angle of attack than by flap deflection. The spanwise pressure distribution on the fin itself indicated a load reversal with angle of attack.

Huffman, J. K.↗