Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “zinc oxide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Impact of cobalt doping on structural and magnetic properties of zinc oxide nanocomposites synthesized by mechanical ball-milling method

A series of zinc oxide (ZnO) semiconductor nanocomposite samples doped with different concentrations of cobalt (Co) were successfully synthesized via simple and highly effective mechanical ball-milling method using suitable precursors. All doped nanocomposites crystallized in hexagonal wurtzite formation of ZnO. No alteration in the wurtzite structure, with no evidence of any segregated secondary phase(s) was detected with increasing doping concentrations. This result unambiguously verified the substitution of Zn 2+ sites by Co 2+ ions in the ZnO host lattice for different doping concentrations. Moreover, room temperature ferromagnetic behavior was observed in all doped nanocomposite samples in the reported work. Present study clearly shows that mechanical ball-milling is a facile, inexpensive, eco-friendly method to synthesize crystalline and magnetic Co doped ZnO nanocomposites for next generation spin-based devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Stable magnesium zinc oxide by reactive Co-Sputtering for CdTe-based solar cells

Magnesium zinc oxide (MZO) is a promising front contact material for CdTe solar cells. Due to its higher band gap than traditional CdS, MZO can reduce parasitic absorption to significantly increase short-circuit current density while also providing a benefit of conduction band offset tuning through Mg:Zn ratio optimization. MZO has been successfully implemented into CdTe devices, however its stability has been of concern. The MZO stability issue has been attributed to the presence of oxygen in the CdTe device processing ambient, leading to double-diode behavior (S-kink) in the current density-voltage curves. Here we report on MZO thin films deposited by reactive co-sputtering. The reactively co-sputtered MZO thin films have encouraging stability, show no significant variation in work function of the surface over a period of 6 months, as measured by Kelvin probe. Energy conversion efficiencies of around 16% have been achieved both with and without presence of oxygen in device processing ambients across multiple research facilities. Finally, these efficiencies should be possible to increase further by tuning of the thin film deposition and device processing parameters, especially through optimization of the back contact.

14 SOLAR ENERGY↗
DOE OSTI2024

Effect of Solvent Composition on Non-DLVO Forces and Oriented Attachment of Zinc Oxide Nanoparticles

Oriented attachment (OA) occurs when nanoparticles in solution align their crystallographic axes prior to colliding and subsequently fuse into single crystals. Traditional colloidal theories such as DLVO provide a framework for evaluating OA but fail to capture key particle interactions due to the atomistic details of both the crystal structure and the interfacial solution structure. Using zinc oxide as a model system, we investigated the effect of the solvent on short-ranged and long-ranged particle interactions and the resulting OA mechanism. In situ TEM imaging showed that ZnO nanocrystals in toluene undergo long-range attraction comparable to 1kT at separations of 10 nm and 3kT near particle contact. These observations were rationalized by considering non-DLVO interactions, namely dipole-dipole forces and torques between the polar ZnO nanocrystals. Langevin dynamics simulations showed stronger interactions in toluene compared to methanol solvents, consistent with the experimental results. Concurrently, we performed atomic force microscopy measurements using ZnO-coated probes for the short-ranged interaction. Our data provided valuable insights into another type of non-DLVO interaction, namely the repulsive solvation force. Specifically, the solvation force was stronger in water compared to ethanol and methanol, due to the stronger hydrogen bonding and denser packing of water molecules at the interface. In conclusion, our results highlight the importance of non-DLVO forces in a general framework for understanding and predicting particle aggregation and attachment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1973

Bidirectional reflectance of zinc oxide

This investigation was undertaken to determine original and useful information about the bidirection reflectance of zinc oxide. The bidirectional reflectance will be studied for the spectra between .25-2.5 microns and the hemisphere above the specimen. The following factors will be considered: (1) surface conditions; (2) specimen preparation; (3) specimen substrate, (4) polarization; (5) depolarization; (6) wavelength; and (7) angles of incident and reflection. The bidirectional reflectance will be checked by experimentally determined angular hemispherical measurements or hemispherical measurements will be used to obtain absolute bidirectional reflectance.

Scott, R.↗
DOE OSTI2022

Effect of proton irradiation temperature on persistent photoconductivity in zinc oxide metal-semiconductor-metal ultraviolet photodetectors

The electrical and structural characteristics of 50-nm-thick zinc oxide (ZnO) metal-semiconductor-metal ultraviolet (UV) photodetectors subjected to proton irradiation at different temperatures are reported and compared. The devices were irradiated with 200 keV protons to a fluence of 1016 cm−2. Examination of the x-ray diffraction (XRD) rocking curves indicates a preferred (100) orientation prior to irradiation, with decrease in crystal quality afterward. Additionally, peak shifts in XRD and Raman spectra of the control sample relative to well-known theoretical positions are indicative of tensile strain in the as-deposited ZnO films. Shifts toward theoretical unstrained positions are observed in the irradiated films, which indicates partial relaxation. Raman spectra also indicate increase in oxygen vacancies (VO) and zinc interstitial defects (Zni) compared to the control sample. Additionally, transient photocurrent measurements performed on each sample at different temperatures showed up to 2× increase in photocurrent decay time constants for irradiated samples vs the control. This persistent photoconductive behavior is linked to the activation of electron and hole traps near the surface, and to the desorption and reabsorption of O2 molecules on the ZnO surface under the influence of UV light. Using an Arrhenius model, trap activation energies were extracted and, by comparing with known energies from the literature, the dominant defects contributing to persistent photoconductivity for each irradiation condition were identified. The persistence of differences in photocurrent transients between different samples months after irradiation indicates that the defects introduced by the suppression of thermally activated dynamic annealing processes have a long-term deleterious effect on device performance.

Heuser, Thomas A. (ORCID:0000000225642400)↗
DOE OSTI2024

Identifying biochemical constituents involved in the mycosynthesis of zinc oxide nanoparticles

Filamentous fungi are known to secrete biochemicals that drive the synthesis of nanoparticles (NPs) that vary in composition, size, and shape; a process deemed mycosynthesis. Following the introduction of precursor salts directly to the fungal mycelia or their exudates, mycosynthesis proceeds at ambient temperature and pressure, and near neutral pH, presenting significant energy and cost savings over traditional chemical or physical approaches. The mycosynthesis of zinc oxide (ZnO) NPs by various fungi exhibited a species dependent morphological preference for the resulting NPs, suggesting that key differences in the biochemical makeup of their individual exudates may regulate the controlled nucleation and growth of these different morphologies. Metabolomics and proteomics of the various fungal exudates suggest that metal chelators, such as hexamethylenetetramine, present in high concentrations in exudates of Aspergillus versicolor are critical for the production dense, well-formed, spheroid nanoparticles. Further, the results also corroborate that the proteinaceous material in the production of ZnO NPs serves as a surface modifier, or protein corona, preventing excessive coagulation of the NPs. Collectively, these findings suggest that NP morphology is regulated by the small molecule metabolites, and not proteins, present in fungal exudates, establishing a deeper understanding of the factors and mechanism underlying mycosynthesis of NPs.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Mycosynthesis of Zinc Oxide Nanoparticles Exhibits Fungal Species Dependent Morphological Preference

Filamentous fungi can synthesize a variety of nanoparticles (NPs), a process referred to as mycosynthesis that requires little energy input, do not require the use of harsh chemicals, occurs at near neutral pH, and do not produce toxic byproducts. While NP synthesis involves reactions between metal ions and exudates produced by the fungi, the chemical and biochemical parameters underlying this process remain poorly understood. Here, the role of fungal species and precursor salt on the mycosynthesis of zinc oxide (ZnO) NPs is investigated. This data demonstrates that all five fungal species tested are able to produce ZnO structures that can be morphologically classified into i) well-defined NPs, ii) coalesced/dissolving NPs, and iii) micron-sized square plates. Further, species-dependent preferences for these morphologies are observed, suggesting potential differences in the profile or concentration of the biochemical constituents in their individual exudates. This data also demonstrates that mycosynthesis of ZnO NPs is independent of the anion species, with nitrate, sulfate, and chloride showing no effect on NP production. Finally, these results enhance the understanding of factors controlling the mycosynthesis of ceramic NPs, supporting future studies that can enable control over the physical and chemical properties of NPs formed through this “green” synthesis method.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1974

Bidirectional reflectance measurement of zinc oxide in 0.25 to 2.5 microns spectrum

An experimental apparatus was designed and used to measure the bidirectional reflectance of zinc oxide in the spectrum 0.25 to 2.5 microns. The nonspecular reflectance is essentially Lambert for wavelengths above 0.40 microns with the most deviation occuring for large source zenith angles. Below 0.400 microns the nonspecular reflectance is greater than Lambert in all directions and is greatest in the forward and backscatter directions. The ratio of the specular component to the nonspecular component at a zenith of 0 degrees was found to increase with source zenith and wavelength for wavelengths above 0.400 microns. Below 0.400 microns this ratio increases as wavelengths decrease. The variation of bidirectional reflectance with wavelength was found to have the characteristics absorption for Zn0 for wavelength below 0.400 microns.

Scott, R. L., Jr.↗
DOE OSTI2024

Thermomechanical properties of stereolithographic 3D-printed zinc oxide nanocomposites

Stereolithography (SLA) is a highly versatile additive manufacturing technique that utilizes various ink formulations to fabricate 3D-printed nanocomposite structures with desired properties. Zinc oxide (ZnO) is a promising candidate due to its excellent mechanical and thermal stability, and compatibility with various polymeric matrices. Here, in this work, varying ink formulations containing ZnO nanoparticles, along with employing appropriate post-printing curing parameters to fabricate SLA 3D-printed acrylate-based nanocomposites with improved mechanical and thermal properties, were reported. This study can significantly contribute to expanding its potential use in practical applications such as biomedical and structural applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Electro-Optical Stability in Gallium Magnesium Zinc Oxide Layers for CdTe Solar Cells

In CdTe solar cells, the emitter electron density, bandgap, and band alignment can be tuned by adjusting alloy composition and stoichiometry in gallium magnesium zinc oxide (GMZO) layers, thereby allowing for critical front interface engineering. For example, computational modeling indicates efficiency can change from 7% to 25% by adjusting these buffer properties even with fixed CdSeTe and CdTe material properties. However, the GMZO as-deposited electro-optical properties can shift during subsequent CdTe deposition, CdCl 2 annealing, and solar cell operation. Here, we examine these changes by sputtering GMZO films on glass, and measuring the electron density before and after post-deposition treatments over a range of temperatures and different ambients. We then compare GMZO to SnO 2 and MZO. The addition of Ga to MgZnO is found to have profound effects on both the electron density and electro-optical stability that should be advantageous for CdTe solar cells.

41 EE - Solar Energy Technologies Office (EE-4S)↗