Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wettability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Designing carbon wetting layers with inorganic salts as additives for enhanced adhesion and molten sodium wettability in electrochemical application

ß” alumina solid-state electrolyte (BASE) is considered one of the most promising materials for sodium batteries due to its high ionic conductivity and exceptional stability with molten sodium. However, at lower operating temperatures, the poor physical contact at the liquid-solid interface between molten sodium and BASE results in high interfacial resistance. In this study, we explore the optimization of carbon wetting layers with various salt additives to enhance adhesion and improve molten sodium wettability. Using a spray-coating method, carbon layers incorporating sodium hexametaphosphate (Na6(PO3)6, SHMP) as an additive demonstrate superior adhesion, mechanical stability, and enhanced wettability with molten sodium. Scanning Electron Microscopy (SEM) analysis reveals that SHMP preserves the porous carbon network required for efficient sodium transport while minimizing structural defects such as cracks and voids. Electrochemical testing using Na symmetric cells confirms that SHMP-modified layers significantly reduce interfacial resistance and overpotential, outperforming No salts counterparts. These findings highlight that the strategic incorporation of suitable additives, such as SHMP, in the design of microscale carbon layers could significantly enhance the performance of molten sodium batteries at lower operating temperatures.

Han, Henry H.↗
NASA NTRS1997

The Wettability of LaRC Colorless Polyimide Resins on Casting Surfaces

Two colorless polyimides developed at NASA Langley Research Center, LaRC -CP1 and LaRC -CP2, are noted for being optically transparent, resistant to radiation, and soluble in the imide form. These materials may be used to make transparent, thin polymer films for building large space reflector/collector inflatable antennas, solar arrays, radiometers, etc. Structures such as these require large area, seamless films produced via spin casting or spray coating the soluble imide on a variety of substrates. The ability of the soluble imide to wet and spread over the mandrel or casting substrate is needed information for processing these structures with minimum waste and reprocessing, thereby, reducing the production costs. The wettability of a liquid is reported as the contact angle of the solid/liquid system. This fairly simple measurement is complicated by the porosity and the amount of contamination of the solid substrate. This work investigates the effect of inherent viscosity, concentration of polyimide solids, and solvent type on the wettability of various curing surfaces.

Miner, Gilda A.↗
NASA NTRS2007

A Process for Producing Highly Wettable Aluminum 6061 Surfaces Compatible with Hydrazine

NASA's Global Precipitation Measurement (GPM) mission is an ongoing Goddard Space Flight Center (GSFC) project whose basic objective is to improve global precipitation measurements. The space-based portion of the mission architecture consists of a primary or core spacecraft and a constellation of NASA and contributed spacecrafts. The efforts described in this paper refer to the core spacecraft (hereafter referred to as simply GPM) which is to be fabricated at GSFC. It has been decided that the GPM spacecraft is to be a "design-for-demise-spacecraft." This requirement resulted in the need for a propellant tank that would also demise or ablate to an appropriate degree upon re-entry. Composite overwrapped aluminum lined propellant tanks with aluminum propellant management devices (PMD) were shown by analyses to demise and thus became the baseline configuration for GPM. As part of the GPM tank development effort, long term compatibility and wettability testing with hydrazine was performed on Al6061 and 2219 coupons fabricated and cleaned by conventional processes. Long term compatibility was confirmed. However, the wettability of the aluminum as measured by contact angle produced higher than desired angles (greater than 30 deg.) with excessive scatter. The availability of PMD materials exhibiting consistently low contact angles aids in the design of simple PMDs. Two efforts performed by Angeles Crest Engineering and funded by GSFC were undertaken to reduce the risk of using aluminum for the GPM PMD. The goal of the first effort was to develop a cleaning or treatment process to produce consistently low contact angles. The goal of the second effort was to prove via testing that the processed aluminum would retain compatibility with hydrazine and retain low contact angle after long term exposure to hydrazine. Both goals were achieved. This paper describes both efforts and the results achieved.

Moore, N. R.↗
DOE OSTI2022

A Study on Surface Texture and Wettability of Femtosecond Laser Treated Aluminum Alloys

This research aims to study the effects of femtosecond laser treatment on surface texture and wettability properties. The first portion of this research studies 2024-T3 aluminum alloy concerning surface texture (e.g., roughness), wettability, and surface free energy. SEM images help aid the researchers in detecting minuscule changes in surface texture. Profilometry extracts topographical data from the surface. A contact angle goniometer measures contact angle, which follows the sessile drop method. Owens, Wendt, Rabel, and Kaelble's method calculates the surface free energy in conjunction with the contact angle. Femtosecond laser modification produces relatively uniform surface morphology at the macroscale. When looking at the microscale, surface morphology differs depending on the interplay between material melting and self-assembly, where the surface becomes rougher after laser treatment. Contact angle results show that all but the control sample and sample 7 exhibit hydrophobic behavior, i.e., contact angle >90°, with Sample 1 having the most significant angle of 115°. The effects of laser parameters on surface energy is apparent. More work is needed to establish correlations among these three quantities: contact angle, surface energy, and laser parameters. The second portion of this research studies aluminum alloy 6061 as the subject material with the primary goal of creating a superhydrophobic surface. A central composite design creates the laser surface texturing design of experiments. SEM images help aid the researchers in detecting minuscule changes in surface texture. A 3D optical profiler extracts topographical data from the surface. The sessile drop method incorporates a contact angle goniometer to measure the contact angle. The response surface method builds a second-order polynomial model for the contact angle and obtains optimized parameters to maximize the contact angle. This research shows that laser surface texturing can generate a wide range of surface profiles and roughness values with geometric features ranging from hundreds of μm to submicron. All three laser parameters (pulse energy, pulse duration, repetition rate) affect surface roughness and contact angle to some degree. To quantify the relationship between the contact angle, pulse energy, and pulse repetition rate, a response surface model for Al 6061 is identified and used to find the optimal conditions of E=214 μJ, tp=10 ps, and fp=2427 Hz with a predicted maximum contact angle of 161°. A confirmation experiment produces a contact angle of 168°, in good agreement with the predicted value.

Angell, Dakota↗
DOE OSTI2022

Transferring Liquid Metal to form a Hybrid Solid Electrolyte via a Wettability-Tuning Technology for Lithium-Metal Anodes

Integrating solid-state electrolyte (SSE) into Li-metal anodes has demonstrated great promise to unleash the high energy density of rechargeable Li-metal batteries. However, fabricating a highly cyclable SSE/Li-metal anode remains a major challenge because the densification of the SSE is usually incompatible with the reactive Li metal. Here, a liquid-metal-derived hybrid solid electrolyte (HSE) is proposed, and a facile transfer technology to construct an artificial HSE on the Li metal is reported. By tuning the wettability of the transfer substrates, electron- and ion-conductive liquid metal is sandwiched between electron-insulating and ion-conductive LiF and oxides to form the HSE. The transfer technology renders the HSE continuous, dense, and uniform. The HSE, having high ion transport, electron shut-off, and mechanical strength, makes the composite anode deliver excellent cyclability for over 4000 h at 0.5 mA cm(-2) and 1 mAh cm(-2) in a symmetrical cell. When pairing with LiFePO4 and sulfur cathodes, the HSE-coated Li metal dramatically enhances the performance of full cells. Therefore, this work demonstrates that tuning the interfacial wetting properties provides an alternate approach to build a robust solid electrolyte, which enables highly efficient Li-metal anodes.

li-metal anodes↗
DOE OSTI2026

Continuous Counter‐Current Microfluidic Liquid–Liquid Extraction Achieved Using a Pair of Wettable Screen Meshes

Continuous counter‐current microfluidic liquid–liquid extraction performs separations by flowing immiscible liquids in opposing directions within a single flow channel. In principle, this flow arrangement enables a large number of theoretical separation units in a small footprint, without using interstage valving, pumping, and phase separation. Despite its potential for excellent separation performance, this microfluidic scheme rarely appears in literature due to the requirement for capillary forces to be greater than hydrodynamic forces for stable flow. We present a novel microfluidic device and flow approaches that overcome this force‐balance challenge, enabling stable, long‐duration continuous counter‐current flow. Additionally, we cover a suite of methodologies for quantifying the performance of the microfluidic device, revealing the number of theoretical equilibrium stages achieved. The enabling technologies include a woven mesh screen‐based microfluidic device architecture that is easily fabricated outside of a clean room, surface functionalization strategies to promote conjugate (organic/aqueous) wettability, flow approaches to eliminate bubbles and carryover, and computer‐aided flow automation with optical measurement of extraction performance. The reported experiments lasted for over 36 h, terminated only at experiment conclusion, where the device still exhibited good performance. Automated Raman spectroscopy was used for solute quantitation of the ternary system tert‐butanol in a toluene/water matrix, a ternary system that was specifically chosen to analyze the device's performance with a small solute partition ratio and to enable in‐line Raman measurements of solute concentrations in both phases. The microfluidic device possessed a 55 mm contact length and a 38.5 µL internal volume. During counter‐current flow, we observed approximately 37 equilibrium stages (37 ± 13) based on a best‐fit of the solute fraction remaining in the aqueous phase using a Kremser Group Method analysis.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Experimental studies on the effects of sheet resistance and wettability of catalyst layer on electro-catalytic activities for oxygen evolution reaction in proton exchange membrane electrolysis cells

As the most important part of electrochemical reaction in proton exchange membrane electrolysis cells (PEMECs) for water splitting, oxygen evolution reaction (OER) occurs at the anode catalyst layer (CL). The distribution of the OER site is affected by many factors, such as properties of CL, operation parameters, procedures, etc. To study the effects of properties of CLs on the distribution of OER site on the CL, and consequently affect the performance of PEMECs, CLs with different sheet resistances are tested under different operation conditions. Furthermore, the phenomena of OER on CLs are captured by a high-speed and micro-scale visualization system in-situ and analysed coupled with electrochemical results. The results in this work show that both sheet resistance and wettability of CLs have significant impact on the distribution of the OER site, which can help optimize the design of membrane electrode assembly and improve the operating parameters for electrochemical devices.

08 HYDROGEN↗
DOE OSTI2021

Nonequilibrium Physics of Multiphase Flow in Porous Media: Wettability and Disorder

Carbon capture and geologic storage, dissociation of methane hydrates in permafrost, enhanced oil recovery, and water dropout in low-temperature fuel cells, all have something in common: two or more fluids flow simultaneously through a porous medium; and the displacement of one fluid by another is often unstable (either due to gravity or viscous forces). Yet, our ability to model multiphase flow in porous media has remained a challenge. The traditional equations are unable to predict, explain, or even reproduce, the formation of the complex patterns observed in experiments. The overarching goal of the project is to develop new physical understanding of the role of wettability and disorder in multiphase flow through permeable media, and to develop new mathematical and computational models at the pore scale and at the continuum scale.

58 GEOSCIENCES↗
DOE OSTI2022

Superhydrophobic to superhydrophilic wettability transition of functionalized SiO 2 nanoparticles

The superhydrophobic and superhydrophilic surfaces and their transitions are of great interest for the production of self-cleaning, anti-biofouling, or corrosion-resistant materials. This research reports the wettability transition from superhydrophobic to superhydrophilic SiO 2 nanoparticles functionalized with 1H, 1H, 2H, 2H-perfluorooctyltriethoxysilane (POTS) and induced by temperature. The functionalization of these nanoparticles was confirmed by Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy (XPS), and transmission electron microscopy. The functionalization of SiO 2 nanoparticles with POTS resulted in superhydrophobic surfaces with water contact angles up to 157°. A sudden transition to superhydrophilic behavior with water contact angles (WCA) below 5° was observed when the sample was heat-treated at 500 °C, despite the presence of fluorine on the surface of these nanoparticles, as confirmed by XPS and transmission electron microscopy. XPS suggested that the transition was caused by the change in orientation of the fluoroalkyl molecules and its partial decomposition due to the loss of the –CF 3 group, resulting in shorter chains with a tail-end group with C–O bonds, which promoted the superhydrophilicity.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Influence of Clay Wettability Alteration on Relative Permeability

Abstract Understanding the wettability of porous materials is important to model fluid flow in the subsurface. One of the critical factors that influences wetting in real reservoirs is the composition of geologic materials. The wetting properties for clay minerals can have a particularly strong impact on flow and transport. In this work, we analyze the chemical composition of a Mt. Simon sandstone core to resolve the microscopic structure of clay regions and assess how alterations to the local wetting properties influence multiphase transport based on core flooding experiments and relative permeability simulations. We show that whichever fluid has greater affinity toward clay minerals will tend to accumulate within these high surface area regions, leading to dramatic shifts in the relative permeability. This work establishes the essential importance of the mineral composition and associated wetting properties in the modeling of flow and transport in reservoir‐scale systems.

Fan, Ming↗
DOE OSTI2020

Two-Phase Fluid Flow Properties of Rough Fractures With Heterogeneous Wettability: Analysis With Lattice Boltzmann Simulations

Fractures are conduits for fluid flow in low-permeability geological formations. Multiphase flow properties of fractures are important in natural processes and in engineering applications such as the evaluation of the sealing capacity of caprocks and productivity of hydrocarbon-bearing tight rocks. Investigations of flow and transport through fractures typically focus on the effects of fracture geometric and mechanical factors such as aperture, roughness, and compressibility. The wettability of the fracture surfaces and its influence on microscale interfacial phenomena and macroscale effective transport properties are seldom studied. In this study, we investigated the effect of heterogeneous wetting properties on the displacement of water by supercritical CO2 through a series of lattice Boltzmann method simulations. The results show the evolution of the CO2 plume within a fracture is controlled by both the roughness of the aperture field and the wetting distribution. We combined these factors into a capillary pressure map that can be related to the macroscopic flow behavior of the fracture. We observed that heterogeneous wetting distributions promote the residual trapping of water where lower capillary pressures allowed for isolated water pockets in higher capillary pressure zones. Analysis of fracture unsteady relative permeability shows the effect of wetting on permeability evolution and provides support for the viscous-coupling relative permeability model. Finally, analysis of the steady-state relative permeability and saturation demonstrates a strong correlation between permeability and the standard deviation of the capillary pressure field. Thus, characterizing the distribution of wetting properties of fractures is crucial to understanding multiphase fracture flow and transport properties.

58 GEOSCIENCES↗
DOE OSTI2020

Molecular-scale origins of wettability at petroleum–brine–carbonate interfaces

Wettability control of carbonates is a central concept for enhanced petroleum recovery, but a mechanistic understanding of the associated molecular-scale chemical processes remains unclear. We directly probe the interface of calcium carbonate (calcite) with natural petroleum oil, synthetic petroleum analogues, and aqueous brines to understand the molecular scale behavior at this interface. The calcite–petroleum interface structure is similar whether or not calcite was previously exposed to an aqueous brine, and is characterized by an adsorbed interfacial layer, significant structural changes within the calcite surface, and increased surface roughness. No evidence for an often-assumed thin-brine wetting layer at the calcite–petroleum interface is observed. These features differ from those observed at the calcite–brine interface, and for parallel measurements using model synthetic petroleum mixtures (consisting of representative components, including dodecane, toluene, and asphaltene). Changes to the interface after petroleum displacement by aqueous brines are also discussed.

02 PETROLEUM↗