Results for “virtual field testing” — Page 3

NASA NTRS2002

Small Particle Response to Fluid Motion using Tethered Particles to Simulate Microgravity

This paper reports on ground based work conducted to support the Spaceflight Definition project SHIVA (Spaceflight Holography Investigation in a Virtual Apparatus). SHIVA will advance our understanding of the movement of a particle in a fluid. Gravity usually dominates the equations of motion, but in microgravity as well as on earth other terms can become important. Before two members of our team found an analytical solution of the equations, numerical methods and/or neglecting terms were required. The general solution predicts that the usually neglected history term becomes important when the characteristic viscous time is in the same order as the vibration period and peaks when the two times are equal. In this case three force terms, the Stokes drag, the added mass, and the history drag must all be included in predicting particle movement. We also developed diagnostic recording methods using holography to save all of the particle field data, allowing the experiment to essentially be transferred from space back to earth in what we call the "virtual apparatus". Using state-of-the-art methods in holography we will quantify the three-dimensional motion of sets of particles, allowing us to test and apply the new analytical solutions. The motion of particles up to 4 mm in diameter in a fluid that oscillates at frequencies up to 100 Hz with amplitudes up to 200 microns is being examined. Ground studies to support the flight development program have employed various schemes to simulate microgravity. One of the most reliable and meaningful methods uses spheres tethered to a fine hair suspended in the fluid. We have also investigated particles with nearly neutral buoyancy. Recordings are made at the peak amplitudes of vibration of the cell providing a measure of the ratio of fluid to particle amplitude. The experiment requires precise location of the particle at the time of recording. The hologram of the particle provides microscopic images of the particle that are used for finding the position with an accuracy of a few microns. To make the experiment more versatile, the spaceflight system will record holograms both on film and electronically. The electronic holograms can be downlinked providing real time data. Results of the ground experiments, the flight experiment design, and data analysis procedures are reported.

Trolinger, J. D.↗

NASA NTRS2002

Small Particle Response to Fluid Motion using Tethered Particles to Simulate Microgravity

This paper reports on ground based work conducted to support the Spaceflight Definition project SHIVA (Spaceflight Holography Investigation in a Virtual Apparatus). SHIVA will advance our understanding of the movement of a particle in a fluid. Gravity usually dominates the equations of motion, but in microgravity as well as on earth other terms can become important. Before two members of our team found an analytical solution of the equations, numerical methods and/or neglecting terms were required. The general solution predicts that the usually neglected history term becomes important when the characteristic viscous time is in the same order as the vibration period and peaks when the two times are equal. In this case three force terms, the Stokes drag, the added mass, and the history drag must all be included in predicting particle movement. We also developed diagnostic recording methods using holography to save all of the particle field data, allowing the experiment to essentially be transferred from space back to earth in what we call the "virtual apparatus". Using state-of-the-art methods in holography we will quantify the three-dimensional motion of sets of particles, allowing us to test and apply the new analytical solutions. The motion of particles up to 4 mm in diameter in a fluid that oscillates at frequencies up to 100 Hz with amplitudes up to 200 microns is being examined. Ground studies to support the flight development program have employed various schemes to simulate microgravity. One of the most reliable and meaningful methods uses spheres tethered to a fine hair suspended in the fluid. We have also investigated particles with nearly neutral buoyancy. Recordings are made at the peak amplitudes of vibration of the cell providing a measure of the ratio of fluid to particle amplitude. The experiment requires precise location of the particle at the time of recording. The hologram of the particle provides microscopic images of the particle that are used for finding the position with an accuracy of a few microns. To make the experiment more versatile, the spaceflight system will record holograms both on film and electronically. The electronic holograms can be downlinked providing real time data. Results of the ground experiments, the flight experiment design, and data analysis procedures are reported.

Trolinger, J. D.↗

NASA NTRS2009

NASA Tech Briefs, February 2009

Tech Briefs are short announcements of innovations originating from research and development activities of the National Aeronautics and Space Administration. They emphasize information considered likely to be transferable across industrial, regional, or disciplinary lines and are issued to encourage commercial application. Topics covered include: Measuring Low Concentrations of Liquid Water in Soil; The Mars Science Laboratory Touchdown Test Facility; Non-Contact Measurement of Density and Thickness Variation in Dielectric Materials; Compact Microwave Fourier Spectrum Analyzer; InP Heterojunction Bipolar Transistor Amplifiers to 255 GHz; Combinatorial Generation of Test Suites; In-Phase Power-Combined Frequency Tripler at 300 GHz; Electronic System for Preventing Airport Runway Incursions; Smaller but Fully Functional Backshell for Cable Connector; Glove-Box or Desktop Virtual-Reality System; Composite Layer Manufacturing with Fewer Interruptions; Improved Photoresist Coating for Making CNT Field Emitters; A Simplified Diagnostic Method for Elastomer Bond Durability; Complex Multifunctional Polymer/Carbon-Nanotube Composites; Very High Output Thermoelectric Devices Based on ITO Nanocomposites; Reducing Unsteady Loads on a Piggyback Miniature Submarine; Ultrasonic/Sonic Anchor; Grooved Fuel Rings for Nuclear Thermal Rocket Engines; Pulsed Operation of an Ion Accelerator; Autonomous Instrument Placement for Mars Exploration Rovers; Mission and Assets Database; TCP/IP Interface for the Satellite Orbit Analysis Program (SOAP); Trajectory Calculator for Finite-Radius Cutter on a Lathe; Integrated System Health Management Development Toolkit.

Source record↗

NASA NTRSDate not supplied

Galactic Cosmic Ray Simulation at the NASA Space Radiation Laboratory – 2021 Update

For missions beyond low Earth orbit to the Moon or Mars, astronauts will encounter a complex space radiation field composed of various ion species with a broad range of energies. Such missions pose significant radiation protection challenges that need to be managed to minimize astronaut exposures and associated health risks. An innovative galactic cosmic ray simulator (GCRsim) was recently developed for the NASA Space Radiation Laboratory at Brookhaven National Laboratory. The GCRsim technology is intended to recapitulate major components of the space radiation environment in a ground-analog laboratory setting. It is used for experimental studies to improve the understanding of biological risks and act as a test bed for counter measure development and validation. Currently, the GCRsim consists of 33 energetic ion beams that collectively simulate the primary and secondary GCR field encountered by astronauts over the broad range of particle types, energies, and linear energy transfer (LET) of interest to human health effects. A virtual workshop was held in December 2020 to assess the status of NASA's GCRsim and attendees examined various aspects of simulator design, with an emphasis on beam selection strategies. Modeling approaches, experimental constraints, areas of consensus, and questions of concern were also discussed in detail. An overview of the workshop considerations and discussion for research strategies that are important for future advancements and applications in space radio biology are presented.

Nafisah Khan↗

NASA NTRS2011

High-Performance 3D Articulated Robot Display

In the domain of telerobotic operations, the primary challenge facing the operator is to understand the state of the robotic platform. One key aspect of understanding the state is to visualize the physical location and configuration of the platform. As there is a wide variety of mobile robots, the requirements for visualizing their configurations vary diversely across different platforms. There can also be diversity in the mechanical mobility, such as wheeled, tracked, or legged mobility over surfaces. Adaptable 3D articulated robot visualization software can accommodate a wide variety of robotic platforms and environments. The visualization has been used for surface, aerial, space, and water robotic vehicle visualization during field testing. It has been used to enable operations of wheeled and legged surface vehicles, and can be readily adapted to facilitate other mechanical mobility solutions. The 3D visualization can render an articulated 3D model of a robotic platform for any environment. Given the model, the software receives real-time telemetry from the avionics system onboard the vehicle and animates the robot visualization to reflect the telemetered physical state. This is used to track the position and attitude in real time to monitor the progress of the vehicle as it traverses its environment. It is also used to monitor the state of any or all articulated elements of the vehicle, such as arms, legs, or control surfaces. The visualization can also render other sorts of telemetered states visually, such as stress or strains that are measured by the avionics. Such data can be used to color or annotate the virtual vehicle to indicate nominal or off-nominal states during operation. The visualization is also able to render the simulated environment where the vehicle is operating. For surface and aerial vehicles, it can render the terrain under the vehicle as the avionics sends it location information (GPS, odometry, or star tracking), and locate the vehicle over or on the terrain correctly. For long traverses over terrain, the visualization can stream in terrain piecewise in order to maintain the current area of interest for the operator without incurring unreasonable resource constraints on the computing platform. The visualization software is designed to run on laptops that can operate in field-testing environments without Internet access, which is a frequently encountered situation when testing in remote locations that simulate planetary environments such as Mars and other planetary bodies.

Powell, Mark W.↗

NASA NTRS1991

Numerical, experimental, and theoretical study of convective instability of flows over pointed bodies at incidence

A study is conducted to investigate whether the behavior of the asymmetric mean flow observed on pointed bodies of revolution at incidence remains consistent with the presence of a convective instability of an original symmetric flow, even in the incidence range where virtually bistable behavior of the asymmetric flow is observed. By means of a retractable wire located near the tip, it is determined experimentally that for all angles of attack tested (30 to 60 degs), changing the size or location of the controlled disturbance results in a finite change in the asymmetric flow field, even to the extent of reversing the sign of the side force or becoming almost symmetric. The process is reversible; returning the wire to an original position likewise restores the corresponding flow field and mean side force. The effect of wire location (roll angle and distance from the tip) as well as angle of attack and flow conditions are evaluated experimentally by means of flow visualization and side-force measurements for a generic ogive-cylinder model in a low-speed wind tunnel. Evaluation of the results in the light of computational observations and theoretical considerations yields an affirmative answer to the question posed.

Degani, David↗

NASA NTRS2015

Carbon Structure Hazard Control

Carbon composite structures are widely used in virtually all advanced technology industries for a multitude of applications. The high strength-to-weight ratio and resistance to aggressive service environments make them highly desirable. Automotive, aerospace, and petroleum industries extensively use, and will continue to use, this enabling technology. As a result of this broad range of use, field and test personnel are increasingly exposed to hazards associated with these structures. No single published document exists to address the hazards and make recommendations for the hazard controls required for the different exposure possibilities from damaged structures including airborne fibers, fly, and dust. The potential for personnel exposure varies depending on the application or manipulation of the structure. The effect of exposure to carbon hazards is not limited to personnel, protection of electronics and mechanical equipment must be considered as well. The various exposure opportunities defined in this document include pre-manufacturing fly and dust, the cured structure, manufacturing/machining, post-event cleanup, and post-event test and/or evaluation. Hazard control is defined as it is applicable or applied for the specific exposure opportunity. The carbon exposure hazard includes fly, dust, fiber (cured/uncured), and matrix vapor/thermal decomposition products. By using the recommendations in this document, a high level of confidence can be assured for the protection of personnel and equipment.

Yoder, Tommy↗

NASA NTRS2001

High Frequency, Long Time Series Measurements from the Bermuda Testbed Mooring in Support of SIMBIOS

It has been recognized that optical moorings are important platforms for the validation of Sea-Viewing Wide Field-of-view Sensor (SeaWiFS). It was recommended that optical moorings be maintained in order to: (1) provide long-term time series comparisons between in situ and SeaWIFS measurements of normalized water-leaving radiance; (2) develop and test algorithms for pigment biomass and phytoplankton primary productivity; and (3) provide long-term, virtually continuous in situ observations which can be used to determine and optimize the accuracy of derived satellite products. These applications require the use of in situ radiometers for long periods of time to evaluate and correct for inherent satellite undersampling (aliasing and biasing) and degradation of satellite color sensors (e.g., drifts as experienced by the Coastal Zone Color Scanner). The Bermuda Testbed Mooring (BTM) program was initiated in 1994 at a site located about 80km southeast of Bermuda in waters of about 4530 m depth. In August 1997, with NASA's support, we started to provide the Sensor Intercomparison and Merger for Biological and Interdisciplinary Oceanic Studies (SIMBIOS) program with large volumes of high frequency, long-term time-series bio-optical data from the BTM for SeaWiFS satellite ocean color groundtruthing and algorithm development. This NASA supported portion of the BTM activity spanned three years and covered five BTM deployments. During these three years, the quality of radiometric data has improved dramatically. Excellent agreement between BTM moored data and both SeaWiFS and nearby ship profile radiometric data demonstrate that technical advances in the moored optical observations have reduced the major difficulties that moored platforms face: biofouling and less frequent calibration.

Dickey, Tommy↗

NASA NTRS2003

Evaluation of Human vs. Teleoperated Robotic Performance in Field Geology Tasks at a Mars Analog Site

Exploration mission designers and planners have costing models used to assess the affordability of given missions - but very little data exists on the relative science return produced by different ways of exploring a given region. Doing cost-benefit analyses for future missions requires a way to compare the relative field science productivity of spacesuited humans vs. virtual presence/teleoperation from a nearby habitat or orbital station, vs. traditional terrestrial-controlled rover operations. The goal of this study was to define science-return metrics for comparing human and robotic fieldwork, and then obtain quantifiable science-return performance comparisons between teleoperated rovers and spacesuited humans. Test runs with a simulated 2015-class rover and with spacesuited geologists were conducted at Haughton Crater in the Canadian Arctic in July 2002. Early results imply that humans will be 1-2 orders of magnitude more productive per unit time in exploration than future terrestrially-controlled robots.

Glass, B.↗

NASA NTRS2003

Spaceflight Holography Investigation in a Virtual Apparatus

The movement of a particle in a fluid is one of the most fundamental processes in physics and plays an important role in materials science. For example, the physics of crystal growth from a nucleation site in solution can be dominated by movement of the solution over the crystal surface. Gravity usually dominates the equations of motion, but in microgravity other terms can dominate, making the equation much more complex. Until recently, the equations were solved only by numerical methods and/or by neglecting terms. During this study, we discovered an exact solution to the equations, which shows that the usually neglected terms become extremely important in microgravity. We also developed diagnostic recording methods using holography to save all of the particle field data, allowing the experiment to essentially be transferred from space back to earth in what we call the virtual apparatus . We will record holograms of particle distributions in motion in microgravity and bring them back to earth for analysis, allowing the study of the full three-dimensional motion of sets of particles, allowing us to test the new analytical solutions. The experiment will also provide accurate measurements of the quasi-steady acceleration of the space platform and other interesting microgravity and g-jitter effects. This program will produce the flight definition for an experiment in the microgravity environment of space to validate the theoretical model. We will design an experiment with the help of the theoretical model that is optimized for testing the model, measuring g, g-jitter, and other microgravity phenomena.

Source record↗

NASA NTRS1972

Crop identification and acreage measurement utilizing ERTS imagery

There are no author-identified significant results in this report. The microdensitometer will be used to analyze data acquired by ERTS-1 imagery. The classification programs and software packages have been acquired and are being prepared for use with the information as it is received. Photo and digital tapes have been acquired for coverage of virtually 100 percent of the test site areas. These areas are located in South Dakota, Idaho, Missouri, and Kansas. Hass 70mm color infrared, infrared, black and white high altitude aerial photography of the test sites is available. Collection of ground truth for updating the data base has been completed and a computer program written to count the number of fields and give total acres by size group for the segments in each test site. Results are given of data analysis performed on digitized data from densitometer measurements of fields of corn, sugar, beets, and alfalfa in Kansas.

Vonsteen, D. H.↗

NASA NTRS2000

SHIVA (Spaceflight Holography Investigation in a Virtual Apparatus)

This paper provides the description and results of a ground-based experiment designed to support the spaceflight program SHIVA, which started its flight definition in 1998. SHIVA will apply new diagnostic tools and experimental techniques to test the validity of a newly discovered analytical solution to the general equation of motion of a particle in a fluid. We have designed a spaceflight experiment with the help of the theoretical model that is optimized for testing the model, and for measuring g, g-jitter, and other microgravity phenomena. Our ongoing, ground-based particle/fluid experiment supports both the experimental and theoretical aspects of the project. The ultimate spaceflight experiment will be similar to the ground-based experiment. The "virtual spaceflight chamber" concept asserts that certain spaceflight experiments can be recorded in holograms in such a manner that having the holograms on earth is optically equivalent to being back in space with unlimited time to conduct the experiment. Properly exploited, this concept can save a significant amount of experiment time in space by effectively bringing the. experiment optically back to earth. SHIVA will accomplish the following: record a large number of holograms of particle fields in space under controlled conditions, extract the precise, three-dimensional position of all of the particles as a function of time, examine the effects of all parameters on the motion of the particles, and test these against predictions of the Coimbra-Range1 solution to the general equation of motion. Particle sizes will range from hundreds of microns up to about 2 mm in diameter and will cover a range of densities and fluid viscosities. Forcing functions will be introduced onto the particle field, including at least the following: a) No isolation in the Spacelab vibration environment. b) Isolation from Spacelab. c) Oscillatory motion from 1 to 100 Hz with amplitudes of a few millimeters. d) Convective fields to be introduced mechanically. The first objective of this research is to understand the physics of particle interactions with fluids and other particles in low Reynolds number flows in microgravity. Secondary objectives are to: (1) observe and quantify g-jitter effects and microconvection on particles in fluids, (2) validate an exact solution to the general equation of motion of a particle in a fluid, and (3) to characterize'the ability of isolating platforms to isolate experiments containing particles in liquids.

Trolinger, James D.↗

NASA NTRS2019

NASA Centennial Challenge: 3D Printed Habitat, Phase 3 Final Results

NASA's Centennial Challenges program uses prize competitions with the goal of accelerating innovation in the aerospace industry. Competitions in the Centennial Challenges portfolio have previously focused on advancements in space robotics, regolith excavation, bio-printing, astronaut suit design, small satellites, and solar-powered vehicles. NASA's Three Dimensional (3D) Printed Habitat Centennial Challenge represents a partnership between NASA and the non-profit partner: Bradley University, with co-sponsors Caterpillar, Bechtel, Brick and Mortar Ventures, the American Concrete Institute, and the United States Army Corps of Engineers (USACE) Engineer Research and Development Center (ERDC) to spur development in automated additive construction technologies. The challenge asks teams to design and construct a scaled and simulated Martian habitat using indigenous materials and large scale 3D automated printing systems. Phase 1 of the competition, held in 2015, was an architectural design competition for habitat concepts that could be 3D printed. Phase 2, completed in 2017, asked teams to develop feedstocks from indigenous materials and hydrocarbon polymer recyclables, and demonstrate automated printing systems to manufacture these feedstocks into test specimens to assess mechanical strength. This paper will discuss the Phase 3 competition, focusing on technology outcomes that can potentially be infused into both terrestrial and planetary construction applications. The Phase 3 competition was divided into two sub-competitions: 1) virtual construction, where teams created a high fidelity building information model (BIM) of their 3D-printed habitat design and 2) the construction competition, which required teams to 3D print a structural foundation and subject materials samples to freeze/thaw testing and impact testing (level 1), produce a habitat element and complete a hydrostatic test (level 2), and additively manufacture a 1:3 scale habitat onsite in a head to head competition at Caterpillar, inc.'s Edwards Demonstration & Learning Center near Peoria, Illinois over the course of three days (level 3). While the Phase 2 competition focused primarily on the development of novel feedstocks and robotic printing systems, Phase 3 emphasized the scale-up of these systems and autonomous operation (demonstrating the capability to operate systems on precursor missions prior to the arrival of crew, or terrestrially in field operation settings where human tending of a manufacturing system may be limited). The Phase 3 virtual construction levels yielded a number of novel habitat designs, including both modular habitats and vertically-oriented habitat concepts. The Phase 3 construction competition also challenged teams to autonomously place penetrations and interfacing elements in additively manufactured structures. The paper will emphasize potential applications for the new materials and technologies developed under the umbrella of the competition within NASA's portfolio and in Earth-based applications such as disaster response and infrastructure improvement.

Construction↗

NASA NTRS2019

Nasa Centennial Challenge: Three Dimensional (3d) Printed Habitat, Phase 3

NASA's Centennial Challenges program uses prize competitions with the goal of accelerating innovation in the aerospace industry. Competitions in the Centennial Challenges portfolio have previously focused on advancements in space robotics, regolith excavation, bio-printing, astronaut suit design, small satellites, and solar-powered vehicles. NASA's Three Dimensional (3D) Printed Habitat Centennial Challenge represents a partnership between NASA and the non-profit partner: Bradley University, with co-sponsors Caterpillar, Bechtel, Brick and Mortar Ventures, the American Concrete Institute, and the United States Army Corps of Engineers (USACE) Engineer Research and Development Center (ERDC) to spur development in automated additive construction technologies. The challenge asks teams to design and construct a scaled and simulated Martian habitat using indigenous materials and large scale 3D automated printing systems. Phase 1 of the competition, held in 2015, was an architectural design competition for habitat concepts that could be 3D printed. Phase 2, completed in 2017, asked teams to develop feedstocks from indigenous materials and hydrocarbon polymer recyclables, and demonstrate automated printing systems to manufacture these feedstocks into test specimens to assess mechanical strength. This paper will discuss the Phase 3 competition, focusing on technology outcomes that can potentially be infused into both terrestrial and planetary construction applications. The Phase 3 competition was divided into two sub-competitions: 1) virtual construction, where teams created a high fidelity building information model (BIM) of their 3D-printed habitat design and 2) the construction competition, which required teams to 3D print a structural foundation and subject materials samples to freeze/thaw testing and impact testing (level 1), produce a habitat element and complete a hydrostatic test (level 2), and additively manufacture a 1:3 scale habitat onsite in a head to head competition at Caterpillar, inc.'s Edwards Demonstration & Learning Center near Peoria, Illinois over the course of three days (level 3). While the Phase 2 competition focused primarily on the development of novel feedstocks and robotic printing systems, Phase 3 emphasized the scale-up of these systems and autonomous operation (demonstrating the capability to operate systems on precursor missions prior to the arrival of crew, or terrestrially in field operation settings where human tending of a manufacturing system may be limited). The Phase 3 virtual construction levels yielded a number of novel habitat designs, including both modular habitats and vertically-oriented habitat concepts. The Phase 3 construction competition also challenged teams to autonomously place penetrations and interfacing elements in additively manufactured structures. The paper will emphasize potential applications for the new materials and technologies developed under the umbrella of the competition within NASA's portfolio and in Earth-based applications such as disaster response and infrastructure improvement.

Centennial challenge↗

NASA NTRS2015

Revisiting the West Clearwater Lake Impact Structure, Canada

The West and East Clearwater Lake impact structures are two of the most distinctive and recognizable impact structures on Earth. Known regionally as the "Clearwater Lake Complex", these structures are located in northern Quebec, Canada (56 deg 10 N, 74 deg 20 W) approximately 125 km east of Hudson Bay. The currently accepted diameters are 36 km and 26 km for the West and East structures, respectively. Long thought to represent a rare example of a double impact, recent age dating has called this into question with ages of approximately 286 Ma and approximately 460-470 Ma being proposed for the West and East structures, respectively. Relatively little is known about the East Clearwater Lake structure. There is no surface exposure and what information there is comes from geophysics and two drill cores obtained in the 1960s. In contrast, the West Clearwater Lake structure is relatively well preserved with large ring of islands in the approximately 30 km diameter lake. Much of the work done on West Clearwater stems from field investigations carried out in 1977 driven by the Apollo program, with a focus on the impact melt rocks and other impactites, which are well exposed on the ring of islands. To our knowledge, the Clearwater Lake impact structures have not been the focus of detailed impact geology field investigations since the 1977 expedition and the only geological map that exists is from the 1960s and is at the reconnaissance level. Our knowledge of impact cratering processes have increased substantially since this time, as have the analytical techniques available for samples. This provided the motivation for a joint Canadian-US-UK expedition to the West Clearwater Lake impact structure in August and September 2015, under the auspices of the FINESSE (Field Investigations to Enable Solar System Science and Exploration) project, part of NASA's Solar System Exploration Research Virtual Institute (SSERVI). We focus here on the impactites of the West Clearwater Lake impact structure. Other ongoing studies, also presented at this conference, focus on central uplift formation, the impact-generated hydrothermal system, xxxx and using WCIS as an analog test site for crew studies of sampling protocols].

West Clearwater Lake↗

NASA NTRS2006

Visualization of a Capsule Entry Vehicle Reaction-Control System (RCS) Thruster

Planar laser-induced fluorescence (PLIF) was used to visualize the reaction control system (RCS) jet flow emanating from the aft-body of an Apollo-geometry capsule test article in the NASA Langley Research Center 31-Inch Mach 10 Air wind tunnel. The RCS jet was oriented normal to the aft surface of the model and had a nominal Mach number of 2.94. The composition of the jet gas by mass was 95% nitrogen (N2) and 5% nitric oxide (NO). The RCS jet flowrate varied between zero and 0.5 standard liters per minute and the angle of attack and tunnel stagnation pressure were also varied. PLIF was used to excite the NO molecules for flow visualization. These flow visualization images were processed to determine the trajectory and to quantify the flapping of the RCS jet. The spatial resolution of the jet trajectory measurement was about 1 mm and the single-shot precision of the measurement was estimated to be 0.02 mm in the far field of the jet plume. The jet flapping, measured by the standard deviation of the jet centerline position was as large as 0.9 mm, while the jet was 1.5-4 mm in diameter (full width at half maximum). Schlieren flow visualization images were obtained for comparison with the PLIF. Surface pressures were also measured and presented. Virtual Diagnostics Interface (VIDI) technology developed at NASA Langley was used to superimpose and visualize the data sets. The measurements demonstrate some of the capabilities of the PLIF method while providing a test case for computational fluid dynamics (CFD) validation.

Danehy, P. M.↗

NASA NTRS2012

Emergent Capabilities Converging into M and S 2.0

The continued operational environment complexity faced by the Department of Defense, despite a restricted resource environment, is a mandate for greater adaptability and availability in joint training. To address these constraints, this paper proposes a model for the potential integration of adaptability training, virtual world capabilities and immersive training into the wider Joint Live Virtual and Constructive (JLVC) Federation, supported by human, social, cultural and behavior modeling, and measurement and assessment. By fusing those capabilities and modeling and simulation enhancements into the JLVC federation, it will create a force who is more apt to arrive at and implement correct decisions, and more able to appropriately seize initiative in the field. The model would allow for the testing and training of capabilities and TTPs that cannot be reasonably explored to their logical conclusions in a 'live' environment, as well as enhance training fidelity for all echelons and tasks.

Reitz, Emilie↗

NASA NTRS2005

Real-Time Aerodynamic Flow and Data Visualization in an Interactive Virtual Environment

Significant advances have been made to non-intrusive flow field diagnostics in the past decade. Camera based techniques are now capable of determining physical qualities such as surface deformation, surface pressure and temperature, flow velocities, and molecular species concentration. In each case, extracting the pertinent information from the large volume of acquired data requires powerful and efficient data visualization tools. The additional requirement for real time visualization is fueled by an increased emphasis on minimizing test time in expensive facilities. This paper will address a capability titled LiveView3D, which is the first step in the development phase of an in depth, real time data visualization and analysis tool for use in aerospace testing facilities.

Schwartz, Richard J.↗