Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “turbulence optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Bearings: Technology and needs

A brief status report on bearing technology and present and near-term future problems that warrant research support is presented. For rolling element bearings a material with improved fracture toughness, life data in the low Lambda region, a comprehensive failure theory verified by life data and incorporated into dynamic analyses, and an improved corrosion resistant alloy are perceived as important needs. For hydrodynamic bearings better definition of cavitation boundaries and pressure distributions for squeeze film dampers, and geometry optimization for minimum power loss in turbulent film bearings are needed. For gas film bearings, foil bearing geometries that form more nearly optimum film shapes for maximum load capacity, and more effective surface protective coatings for high temperature operation are needed.

Anderson, W. J.↗
NASA NTRS1982

Turbulent boundary layer drag reduction using riblets

An experimental study of low-speed turbulent boundary layer flow over longitudinally grooved surfaces (i.e., riblets) is discussed. Results obtained with a highly accurate drag balance indicate that v-groove riblet surfaces can produce consistent net drag reductions as large as 8 percent provided the height and spacing of the grooves in terms of law of the wall variables are less than 25 wall units. Momentum balances confirmed these direct drag measurements. Conditionally sampled data indicate that the burst frequency for riblets is approximately the same as that for a flat plate but turbulence intensity is reduced. Attempts to optimize the net drag reduction by varying riblet cross-sectional geometry and alignment are also discussed.

Walsh, M. J.↗
NASA NTRS1987

Computational mechanics and physics at NASA Langley Research Center

An overview is given of computational mechanics and physics at NASA Langley Research Center. Computational analysis is a major component and tool in many of Langley's diverse research disciplines, as well as in the interdisciplinary research. Examples are given for algorithm development and advanced applications in aerodynamics, transition to turbulence and turbulence simulation, hypersonics, structures, and interdisciplinary optimization.

South, Jerry C., Jr.↗
NASA NTRS1997

Low-leakage and low-instability labyrinth seal

Improved labyrinth seal designs are disclosed. The present invention relates to labyrinth seal systems with selected sealing surfaces and seal geometry to optimize flow deflection and produce maximum turbulent action. Optimum seal performance is generally accomplished by providing sealing surfaces and fluid cavities formed to dissipate fluid energy as a function of the geometry of the sealing surfaces along with the position and size of the fluid cavities formed between members of the labyrinth seal system. Improved convex surfaces, annular flow reversal grooves, flow deflection blocks and rough, machined surfaces cooperate to enhance the performance of the labyrinth seal systems. For some labyrinth seal systems a mid-cavity throttle and either rigid teeth or flexible spring teeth may be included.

Rhode, David L.↗
NASA NTRSDate not supplied

AI-Enhanced Computational Tools for Entry Systems Modeling

To advance the understanding of complex atmospheric entry phenomena, NASA’s Entry Systems Modeling (ESM) team [1] has developed high-fidelity computational tools addressing multiscale challenges, from material microstructures to full-scale heatshield response. This abstract highlights a subset of ESM tools, focusing on AI integration to enhance workflows and predictive modeling. - PuMA [2] computes effective material properties from high-resolution micro-CT scans, supporting TPS analysis for NASA missions. - TomoSAM [3] automates 3D tomography dataset segmentation for PuMA using the Segment Anything Model, reducing manual effort and improving accuracy. - PATO [4] models porous reactive materials under extreme conditions, with advancements such as unified solvers, mechanical erosion, and TPS coatings for NASA missions. - arcjetCV [5] employs deep learning to analyze arc jet test footage, measuring recession rates, shape changes, and shock standoff distances, bridging simulations, and experiments to reveal TPS ablation behavior. - ARCHeS [6] simulates arc heater plasma flows, modeling turbulence, radiation, and electromagnetic interactions to optimize arc heater performance, validate TPS under extreme conditions, and serve as a foundation for developing digital twins of arc heater facilities. - SPARTA [7] simulates rarefied hypersonic flows and gas-surface interactions for planetary entry missions, leveraging GPU architectures for scalable and efficient aerothermal and ablation analyses. AI-driven solutions, such as deep learning segmentation, have streamlined workflows in ESM tools and still hold significant potential to further accelerate processes and enhance automation in entry systems modeling. [1] Haskins, J.B. (2023), [2] Ferguson, J.C. (2018), [3] Meurisse, J.B.E. (2018), [4] Semeraro, F. (2023), [5] Quintart, A. (2024) [6] Meurisse, J.B.E. (2022), [7] Plimpton, S.J. (2019)

Predictive Modeling↗
NASA NTRS2012

Aircraft Dynamic Modeling in Turbulence

A method for accurately identifying aircraft dynamic models in turbulence was developed and demonstrated. The method uses orthogonal optimized multisine excitation inputs and an analytic method for enhancing signal-to-noise ratio for dynamic modeling in turbulence. A turbulence metric was developed to accurately characterize the turbulence level using flight measurements. The modeling technique was demonstrated in simulation, then applied to a subscale twin-engine jet transport aircraft in flight. Comparisons of modeling results obtained in turbulent air to results obtained in smooth air were used to demonstrate the effectiveness of the approach.

Morelli, Eugene A.↗
NASA NTRS2006

Coherent optical array receiver experiment : design, implementation and BER performance of a multichannel coherent optical receiver for PPM signals under atmospheric turbulence

The performance of a coherent free-space optical communication system operating in the presence of turbulence is investigated. Maximum Likelihood Detection techniques are employed to optimally detect Pulse Position Modulated signals with a focal-plane detector array, and reconstruct the turbulence-degraded signals. The experimental demonstration of this project and results may be divided in three parts; two of which have already been explained in previous publications (1,2). This latest paper shows the final experimental results, including investigation of performance of the Coherent Optical Receiver Experiment (CORE) performed at the laboratory facilities at JPL. Bit Error Rate (BER) is presented for single and multichannel optical receivers, where quasi-shot noise limited performance is achieved, under simulated turbulence conditions using non-coherent post-detection processing techniques.

Hassibi, Babak↗
NASA NTRS2003

Constrained Aeroacoustic Shape Optimization Using the Surrogate Management Framework

Reduction of noise generated by turbulent flow past the trailing-edge of a lifting surface is a challenge in many aeronautical and naval applications. Numerical predictions of trailing-edge noise necessitate the use of advanced simulation techniques such as large-eddy simulation (LES) in order to capture a wide range of turbulence scales which are the source of broadband noise. Aeroacoustic calculations of the flow over a model airfoil trailing edge using LES and aeroacoustic theory have been presented in Wang and Moin and were shown to agree favorably with experiments. The goal of the present work is to apply shape optimization to the trailing edge flow previously studied, in order to control aerodynamic noise.

Marsden, Alison L.↗
NASA NTRS1976

Estimation of characteristics and stochastic control of an aircraft flying in atmospheric turbulence

An adaptive control technique to improve the flying qualities of an aircraft in turbulence was investigated. The approach taken was to obtain maximum likelihood estimates of the unknown coefficients of the aircraft system and then, using these estimates along with the separation principle, to define the stochastic optimal control. The maximum likelihood estimation technique that accounted for the effects of turbulence provided good estimates of the unknown coefficients and of the turbulence. The assessment of the stochastic optimal control based on the maximum likelihood estimates showed that the desired effects were attained for the regulator problem of minimizing pitch angle and the tracking problem of requiring normal acceleration to follow the pilot input.

Iliff, K. W.↗
NASA NTRS1993

Characteristics of vertical and lateral tunnel turbulence measured in air in the Langley Transonic Dynamics Tunnel

Preliminary measurements of the vertical and lateral velocity components of tunnel turbulence were obtained in the Langley Transonic Dynamics Tunnel test section using a constant-temperature anemometer equipped with a hot-film X-probe. For these tests air was the test medium. Test conditions included tunnel velocities ranging from 100 to 500 fps at atmospheric pressure. Standard deviations of turbulence velocities were determined and power spectra were computed. Unconstrained optimization was employed to determine parameter values of a general spectral model of a form similar to that used to describe atmospheric turbulence. These parameters, and others (notably break frequency and integral scale length), were determined at each test condition and compared with those of Dryden and Von Karman atmospheric turbulence spectra. When the data were discovered to be aliased, the spectral model was modified to account for and 'eliminate' the aliasing.

Sleeper, Robert K.↗
NASA NTRS2014

Conceptual Design Optimization of an Augmented Stability Aircraft Incorporating Dynamic Response Performance Constraints

This research focused on incorporating stability and control into a multidisciplinary de- sign optimization on a Boeing 737-class advanced concept called the D8.2b. A new method of evaluating the aircraft handling performance using quantitative evaluation of the sys- tem to disturbances, including perturbations, continuous turbulence, and discrete gusts, is presented. A multidisciplinary design optimization was performed using the D8.2b transport air- craft concept. The con guration was optimized for minimum fuel burn using a design range of 3,000 nautical miles. Optimization cases were run using xed tail volume coecients, static trim constraints, and static trim and dynamic response constraints. A Cessna 182T model was used to test the various dynamic analysis components, ensuring the analysis was behaving as expected. Results of the optimizations show that including stability and con- trol in the design process drastically alters the optimal design, indicating that stability and control should be included in conceptual design to avoid system level penalties later in the design process.

Welstead, Jason↗
NASA NTRS2003

Optimal Disturbances in Boundary Layers Subject to Streamwise Pressure Gradient

Laminar-turbulent transition in shear flows is still an enigma in the area of fluid mechanics. The conventional explanation of the phenomenon is based on the instability of the shear flow with respect to infinitesimal disturbances. The conventional hydrodynamic stability theory deals with the analysis of normal modes that might be unstable. The latter circumstance is accompanied by an exponential growth of the disturbances that might lead to laminar-turbulent transition. Nevertheless, in many cases, the transition scenario bypasses the exponential growth stage associated with the normal modes. This type of transition is called bypass transition. An understanding of the phenomenon has eluded us to this day. One possibility is that bypass transition is associated with so-called algebraic (non-modal) growth of disturbances in shear flows. In the present work, an analysis of the optimal disturbances/streamwise vortices associated with the transient growth mechanism is performed for boundary layers in the presence of a streamwise pressure gradient. The theory will provide the optimal spacing of the control elements in the spanwise direction and their placement in the streamwise direction.

Tumin, Anatoli↗
NASA NTRSDate not supplied

Numerical Investigation of Flow Over Periodic Hill

Hybrid turbulence modeling strategies that blend between large-eddy simulation and Reynolds-averaged Navier-Stokes promise to make optimal use of the available grid resolution. A delayed detached eddy simulation hybrid turbulence modeling strategy, based on the shear-stress transport turbulence model, was implemented into a finite-volume compressible Navier-Stokes code. Then the flow through a two-dimensional periodic hill channel was simulated. This geometry is a widely accepted benchmark test case for validating hybrid turbulence modeling strategies. The computational grid for the simulation was downloaded from a hybrid turbulence model validation website. The present hybrid turbulence model simulation predicts the size of the separated flow region as well as velocity and Reynolds stress profiles in good agreement with large-eddy simulation reference data.

Computational Fluid Dynamics↗
NASA NTRS1987

Numerical optimization of conical flow waveriders including detailed viscous effects

A family of optimized hypersonic waveriders is generated and studied wherein detailed viscous effects are included within the optimization process itself. This is in contrast to previous optimized waverider work, wherein purely inviscid flow is used to obtain the waverider shapes. For the present waveriders, the undersurface is a streamsurface of an inviscid conical flowfield, the upper surface is a streamsurface of the inviscid flow over a tapered cylinder (calculated by the axisymmetric method of characteristics), and the viscous effects are treated by integral solutions of the boundary layer equations. Transition from laminar to turbulent flow is included within the viscous calculations. The optimization is carried out using a nonlinear simplex method. The resulting family of viscous hypersonic waveriders yields predicted high values of lift/drag, high enough to break the L/D barrier based on experience with other hypersonic configurations. Moreover, the numerical optimization process for the viscous waveriders results in distinctly different shapes compared to previous work with inviscid-designed waveriders. Also, the fine details of the viscous solution, such as how the shear stress is distributed over the surface, and the location of transition, are crucial to the details of the resulting waverider geometry. Finally, the moment coefficient variations and heat transfer distributions associated with the viscous optimized waveriders are studied.

Bowcutt, Kevin G.↗
NASA NTRS1989

Further Improvements to Nozzle Boundary Layer Calculations in BLIMPJ

Further improvements made to advance the current Boundary Layer Integral Matrix Procedure - Version J (BLIMPJ) containing previously modeled simplified calculation methods by accounting for condensed phase, thick boundary layer and free stream turbulence effects are discussed. The condensed phase effects were included through species composition effect considered via input to the code and through particle damping effect considered via a turbulence model. The thrust loss calculation procedure for thick boundary layer effects was improved and the optimization of net thrust with respect to nozzle length was performed. The effects of free stream turbulence were approximately modeled in the turbulence model.

Praharaj, S. C.↗
NASA NTRS1992

On the complexity of turbulence near a wall

Some measures of the intrinsic complexity of the near wall turbulence are reviewed. The number of modes required in an 'optimal' eigenfunction expansion is compared with the dimension obtained from the calculation of Liapunov exponents. These measures are of the same order, but they are very large. It is argued that the basic building block element of the near wall turbulence can be isolated in a small region of space (minimal flow unit). When the size of the domain is taken into account, the dimension becomes more manageable.

Moin, Parviz↗
NASA NTRS1996

Toward a Turbulence Constitutive Relation for Rotating Flows

In rapidly rotating turbulent flows the largest scales of the motion are in approximate geostrophic balance. Single-point turbulence closures, in general, cannot attain a geostrophic balance. This article addresses and resolves the possibility of constitutive relation procedures for single-point second order closures for a specific class of rotating or stratified flows. Physical situations in which the geostrophic balance is attained are described. Closely related issues of frame-indifference, horizontal nondivergence, Taylor-Proudman theorem and two-dimensionality are, in the context of both the instantaneous and averaged equations, discussed. It is shown, in the absence of vortex stretching along the axis of rotation, that turbulence is frame-indifferent. A derivation and discussion of a geostrophic constraint which the prognostic equations for second-order statistics must satisfy for turbulence approaching a frame-indifferent limit is given. These flow situations, which include rotating and nonrotating stratified flows, are slowly evolving flows in which the constitutive relation procedures are useful. A nonlinear non-constant coefficient representation for the rapid-pressure strain covariance appearing in the Reynolds stress and heat flux equations consistent with the geostrophic balance is described. The rapid-pressure strain model coefficients are not constants determined by numerical optimization but are functions of the state of the turbulence as parameterized by the Reynolds stresses and the turbulent heat fluxes. The functions are valid for all states of the turbulence attaining their limiting values only when a limit state is achieved. These issues are relevant to strongly vortical flows as well as flows such as the planetary boundary layers, in which there is a transition from a three-dimensional shear driven turbulence to a geostrophic or horizontal turbulence.

Ristorcelli, J. R.↗
NASA NTRS2001

Accuracy Assessment of Response Surface Approximations for Supersonic Turbine Design

There is a growing trend to employ CFD tools to supply the necessary information for design optimization of fluid dynamics components/systems. Such results are prone to uncertainties due to reasons including discretization. errors, incomplete convergence of computational procedures, and errors associated with physical models such as turbulence closures. Based on this type of information, gradient-based optimization algorithms often suffer from the noisy calculations, which can seriously compromise the outcome. Similar problems arise from the experimental measurements. Global optimization techniques, such as those based on the response surface (RS) concept are becoming popular in part because they can overcome some of these barriers. However, there are also fundamental issues related to such global optimization technique such as RS. For example, in high dimensional design spaces, typically only a small number of function evaluations are available due to computational and experimental costs. On the other hand, complex features of the design variables do not allow one to model the global characteristics of the design space with simple quadratic polynomials. Consequently a main challenge is to reduce the size of the region where we fit the RS, or make it more accurate in the regions where the optimum is likely to reside. Response Surface techniques using either polynomials or and Neural Network (NN) methods offer designers alternatives to conduct design optimization. The RS technique employs statistical and numerical techniques to establish the relationship between design variables and objective/constraint functions, typically using polynomials. In this study, we aim at addressing issues related to the following questions: (1) How to identify outliers associated with a given RS representation and improve the RS model via appropriate treatments? (2) How to focus on selected design data so that RS can give better performance in regions critical to design optimization? (3) How to combine NN and polynomial techniques for improving the accuracy of the RS model?

Papila, Nilay↗