SEARCH · Engineering Papers

Results for “transducer error”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Sonic spark chambers for cosmic-ray experiments

The sonic spark chamber provides an attractive high resolution hodoscope for low flux cosmic ray experiments. Spark position is determined by measurement of the time of flight of the sonic shock front from the spark position to a number of piezoelectric transducers placed at the periphery of the chamber. For each spark, four quantities must be determined: the spark coordinates, the sound velocity, and the spark 'size'. By over-determining the four parameters, high accuracy is possible. With eight sonic transducers, air-gap spark positions were measured with an error of less than 100 microns everywhere over a 1 sq m region.

Ahlen, S. P.↗

NASA NTRS1993

Modelling, calibration, and error analysis of seven-hole pressure probes

This report describes the calibration of a nonnulling, conical, seven-hole pressure probe over a large range of flow onset angles. The calibration procedure is based on the use of differential pressures to determine the three components of velocity. The method allows determination of the flow angle and velocity magnitude to within an average error of 1.0 deg and 1.0 percent, respectively. Greater accuracy can be achieved by using high-quality pressure transducers. Also included is an examination of the factors which limit the use of the probe, a description of the measurement chain, an error analysis, and a typical experimental result. In addition, a new general analytical model of pressure probe behavior is described, and the validity of the model is demonstrated by comparing it with experimentally measured calibration data for a three-hole yaw meter and a seven-hole probe.

Zillac, G. G.↗

NASA NTRS1981

Image motion compensation on the Spacelab 2 Solar Optical Universal Polarimeter /SL2 SOUP/

The SOUP experiment on Spacelab 2 includes a 30 cm visible light telescope and focal plane package mounted on the Instrument Pointing System (IPS). Scientific goals of the experiment dictate pointing stability requirements of less than 0.05 arcsecond jitter over periods of 5-20 seconds. Quantitative derivations of these requirements from two different aspects are presented: (1) avoidance of motion blurring of diffraction-limited images; (2) precise coalignment of consecutive frames to allow measurement of small image differences. To achieve this stability, a fine guider system capable of removing residual jitter of the IPS and image motions generated on the IPS cruciform instrument support structure has been constructed. This system uses solar limb detectors in the prime focal plane to derive an error signal. Image motion due to pointing errors is compensated by the agile secondary mirror mounted on piezoelectric transducers, controlled by a closed-loop servo system.

Tarbell, T. D.↗

NASA NTRS1989

Digital to synchro converter

A digital-to-synchro converter is provided where a binary input code specifies a desired shaft angle and where an resolver type position transducer is employed with additional circuitry to generate a shaft position error signal indicative of the angular difference between the desired shaft angle and the actual shaft angle. The additional circuitry corrects for known and calculated errors in the shaft position detection process and equipment.

Predina, Joseph P.↗

NASA NTRS1990

Shock-tube calibration of a fast-response pressure transducer

The sensitivity of a miniature fast-response piezoresistive pressure transducer determined dynamically was found to be slightly higher than that determined statically. Thus, mean pressures in a turbulent or unsteady flowfield that are measured using statically-calibrated pressure transducers would be slightly above true values. Unsteady pressure measurements to obtain space-time correlations and spectra can, however, be properly performed if the slight error is acceptable. These measurements are, obviously, subjected to limitations imposed by the bandwidth and the spatial resolution of the transducer. The noise spectrum revealed that the noise is predominantly above the transducer's resonant frequency. Filtering to improve the signal-to-noise ratio is particularly necessary when using the transducers at their low range. Transducer drift increases the signal-to-noise ratio and can adversely affect mean measurements.

Chung, Kung-Ming↗

NASA NTRS1974

Ultrasonic dispersion (delta V/V) determined from mechanical resonance frequency shifts

With standing wave ultrasonic techniques, small changes in phase velocity which result from changes in some external parameter (e.g., temperature or magnetic field) have traditionally been determined by observing shifts in the mechanical resonance frequency of a composite resonator. Some previous investigators have assumed that the fractional change in velocity is equal to the fractional change in frequency. Substantially improved formulas for determining the dispersion are presented and one of these is shown to be much more accurate than all previous approximations. The results of simulated and actual experiments over wide ranges of dispersion, transducer loading parameter, and frequency are analyzed in order to compare the errors inherent in the various approximations.

Moerner, W. E.↗

NASA NTRS1989

Ultrasonic pulsed phase locked loop interferometer for bolt load measurements

The pulsed phase-locked-loop bolt monitor (P2L2) that uses ultrasonic waves to measure bolt preload with accuracies ranging from 1 to 3 percent (depending on the specific bolt) is described. To remeasure bolt load after installation, a thermal calibration factor compensates for bolt temperature changes, and a standard reference block allows correction for acoustic phase errors due to measurement equipment configuration such as utilization of a different transducer, couplant, or cable. Some examples of critical applications including Space Shuttle landing-gear wheels and NASA wind-tunnel fan blades are discussed.

Allison, S. G.↗

NASA NTRSDate not supplied

Methodology for Validation of Unsteady Pressure-Sensitive Paint Measurements using Pressure Transducers

Unsteady Pressure-Sensitive Paint (uPSP) technology provides simultaneously high-frequency and high-spatial resolution surface pressure fluctuation measurements. It has demonstrated value in wind tunnel test facilities to evaluate aerospace vehicle unsteady aerodynamics. The calibration of measurements from digital pixel counts into corresponding physical units relies on both lab-based and in-situ calibration steps, and its validation is both challenging and critical to adoption of the technology. We present a rigorous methodology for direct comparison of uPSP-derived surface pressure measurements to reference pressure transducer data based on a model of the camera-based measurement error, a model of the flow field pressure signal, and their propagation through the uPSP data reduction algorithm. The methodology is demonstrated on data collected in a small-scale, subsonic wind tunnel test as well as data collected from a Space Launch System unsteady aerodynamics characterization test at the NASA Ames Research Center Unitary Plan Wind Tunnel Complex.

Pressure-Sensitive Paint↗

NASA NTRSDate not supplied

Validating uPSP with Transducers

Pressure-Sensitive Paint↗

NASA NTRS1990

Update on results of SPRE testing at NASA

The space power research engine (SPRE I), a free-piston Stirling engine with a linear alternator, was tested as a candidate for high-capacity space power. A portion of the test data from the SPRE I, essentially in its baseline configuration while operating with helium at heat exchanger metal temperature ratios ranging from 1.6 to 2.4 and mean cycle pressures of 7.5 and 15.0 Mpa, are presented. HFAST computer code predictions are presented for comparison. The measured results at 7.5 and 15 MPa, from the first day, from the first day of testing, at temperature ratios from 1.6 to 2.0 agreed fairly well with the HFAST code predictions; within -8.8 percent to +11.9 percent for PV power and -2.7 to +1.07 percentage points for PV efficiency. Measured compression-space pressure amplitude was 5.1 to 11.1 percent below predictions; although these results were within the error bands, there was poorer agreement than observed for previous tests, and the transducer calibration is suspect. All of the dynamic pressure transducer calibrations will be verified before testing is resumed. Measured pressure phase angles were within -1.95 percent to +5.37 percent of the predictions, which is much closer than previously observed. The poor agreement of the measured heat flow to the heater with the code appears to be due to thermocouple degradation.

Cairelli, James E.↗

NASA NTRS1991

Active isolation of vibrations with adaptive structures

Vibration transmission in structures is controlled by means of a technique which employs distributed arrays of piezoelectric transducers bonded to the supporting structure. Distributed PVDF piezoelectric strips are employed as error sensors, and a two-channel feedforward adaptive LMS algorithm is used for minimizing error signals and thereby controlling the structure. A harmonic force input excites a thick plate, and a receiving plate is configured with three pairs of piezoelectric actuators. Modal analyses are performed to determine the resonant frequencies of the system, and a scanning laser vibrometer is used to study the shape of the response of the receiving plate during excitation with and without the control algorithm. Efficient active isolation of the vibrations is achieved with modal suppression, and good control is noted in the on-resonance cases in which increased numbers of PVDF sensors and piezoelectric actuators are employed.

Guigou, C.↗

NASA NTRS1968

Miniature pressure transducer for stressed member application

Miniature pressure transducer responds to static or dynamic pressures acting against a structural surface without introducing errors caused by stresses in the structural surface. This is accomplished by a thin stainless steel pressure sensing diaphragm with an attached foil strain gage.

Walker, R. R.↗

NASA NTRS1972

An investigation of compressor noise by use of a spinning mode synthesizer.

Use of the Spinning Mode Synthesizer (SMS) as a tool for studying the properties of such complex waves as those generated by fan engines. This has greatly reduced the amount of trial and error techniques used for optimizing duct liners. The SMS was designed by using simple transducer theory and properly controlling the phasing to each of 8 loudspeakers. It provides a means for making in-duct measurements of the radial, axial, and circumferential modal distributions. Results are presented which show that the device is of value for investigation of the highly complex nature of compressor radiated noise.

Oslac, M. J.↗

NASA NTRS1983

An evaluation of Space Shuttle Orbiter forward fuselage surface pressures - Comparison with wind tunnel and theoretical predictions

In order for ground-based pressure distribution techniques to be verified by the actual performance of the Space Shuttle Orbiter in flight, a comparative study of flight pressure data and both wind tunnel and computational data is presented. The flight pressure data, obtained from measurements on the Orbiter's surface during atmospheric reentry, are part of the overall Orbiter flight data system designated Development Flight Instrumentation. Also given is an analysis of the Orbiter pressure data system, including its transducers, their behavior, and their calibration. The two analyses are the bases of an error assessment calculation for the flight data, as well as an explanation of any discrepancies between flight and ground-based data.

Bradley, P. F.↗

NASA NTRS1994

System Measures Loads In Bolts

Improved technique for ultrasonic nondestructive measurement of loads in bolts involves use of pulsed phase-locked loop interferometer. Provides for correction of errors and for automatic readout of loads in bolts. Actual bolt load measured, using transducers rebonded after bolts tightened. Calibration block and thermometer added. Technique applicable to critical fasteners in aerospace applications, nuclear reactors, petroleum and other chemical processing plants, steel bridges, and other structures.

Allison, Sidney G.↗

NASA NTRS1983

Flexible Coupling Corrects Shaft Misalinements

Proposed flexible coupling provides nearly error free measurements of shaft rotation in presence of misalinements between shaft and position sensing transducer. Intended to be used in situations in which input or output shaft is mounted on flexible joint. Its function is to insure equal input and output angular velocities by forcing input and output shafts to remain parallel.

Mayo, R. A.↗

DOE OSTI2020

Full circle mechanical dynamic characterization including experimental modal analysis and finite element analysis

During operation, it was observed that a specific mechanical system experienced undesirable vibration and it became necessary to understand and mitigate this phenomenon. This document investigates the tools, methodology, and results of the dynamic characterization of the system. The characterization makes use of the experimental modal analysis (EMA) methods of single input multiple output (SIMO) and single input single output (SISO). The validity of the theory of reciprocity is confirmed to minimize measurement error, cost, and time of repeat testing. Finite element analysis (FEA) is used in choosing transducer and modal impact locations to adequately characterize the system. Single degree of freedom (SDOF) and multiple degree of freedom (MDOF) curve fitting is used to fully characterize the system’s mode shapes and natural frequencies. The EMA characterization results are used to modify and validate the FEA model so that FEA can be used to model potential structural modifications to the system to mitigate the undesirable vibration. Structural modifications are chosen, implemented, and their effectiveness is quantified using EMA. Finally, a qualitative evaluation of the methodology of FEA validation by EMA and tuning of the model to match the experimental results is discussed.

42 ENGINEERING↗

NASA NTRS1982

Matching of Apparent-Strain Characteristics

Strain gages are temporarily bonded to surface of test block. Apparent strain is recorded in excursion to -190 degrees C, and gages are disbonded following heating to elevated temperature. Matching strain gages for cryogenic use has several advantages. Initial accuracy for cryogenic transducers is greatly improved, less apparent-strain correction wire is required and there are smaller errors due to loop data caused by long pieces of correction wire.

Moore, T. C.↗