Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “systems simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2016

Evaluation of fuel-borne sodium effects on a DOC-DPF-SCR heavy-duty engine emission control system: Simulation of full-useful life

Here we report that for renewable fuels to displace petroleum, they must be compatible with emissions control devices. Pure biodiesel contains up to 5 ppm Na + K and 5 ppm Ca + Mg metals, which have the potential to degrade diesel emissions control systems. This study aims to address these concerns, identify deactivation mechanisms, and determine if a lower limit is needed. Accelerated aging of a production exhaust system was conducted on an engine test stand over 1001 h using 20% biodiesel blended into ultra-low sulfur diesel (B20) doped with 14 ppm Na. This Na level is equivalent to exposure to Na at the uppermost expected B100 value in a B20 blend for the system full-useful life. During the study, NOx emissions exceeded the engine certification limit of 0.33 g/bhp-hr before the 435,000-mile requirement. Replacing aged diesel oxidation catalyst (DOC), diesel particulate filter (DPF), and selective catalytic reduction (SCR) devices with new degreened parts showed that each device contributed equally to the NOx increase. Following this systems-based evaluation, a detailed investigation of the individual components was completed. Na was determined to have minimal impact on DOC activity. For this system, it is estimated that B20-Na resulted in 50% more ash into the DPF. However, the Na did not diffuse into the cordierite DPF nor degrade its mechanical properties. The SCR degradation was found to be caused by a small amount of precious group metals (PGM) contamination that increased NH3 oxidation, and lowered NOx reduction. Therefore, we determined that the primary effect of Na in this study is through increased ash in the DPF rather than deactivation of the catalytic activity.

42 ENGINEERING↗
NASA NTRS1972

Systems simulation for an airport trailing vortex warning system

The approach, development, and limited system studies associated with a system simulation for an Airport Trailing Vortex Warning System are documented. The usefulness is shown of a systems engineering approach to the problem of developing a system, as dictated by aircraft vortices, which will increase air-traffic flow in the takeoff/landing corridors of busy airports while maintaining the required safety factor for each operation. The simulation program has been developed in a modular form which permits new, more sophisticated component models, when they become available and are required, to be incorporated into the program with a minimum of program modifications. This report documents a limited system study that has been performed using this Total System Simulation Model. The resulting preliminary system requirements, conclusions, and recommendations are given.

Jeffreys, H. B.↗
NASA NTRS1981

A Nonlinear Propulsion System Simulation Technique for Piloted Simulators

In the past, propulsion system simulations used in flight simulators have been extremely simple. This resulted in a loss of simulation realism since significant engine and aircraft interactions were neglected and important internal engine parameters were not computed. More detailed propulsion system simulators are needed to permit evaluations of modern aircraft propulsion systems in a simulated flight environment. A real time digital simulation technique has been developed which provides the capabilities needed to evaluate propulsion system performance and aircraft system interaction on manned flight simulators. A parameter correlation technique is used with real and pseudo dynamics in a stable integration convergence loop. The technique has been applied to a multivariable propulsion system for use in a piloted NASA flight simulator program. Cycle time is 2.0 ms on a Univac 1110 computer and 5.7 ms on the simulator computer, a Xerox Sigma 8. The model is stable and accurate with time steps up to 50 ms. The program evaluated the simulation technique and the propulsion system digital control. The simulation technique and model used in that program are described and results from the simulation are presented.

Mihaloew, J. R.↗
NASA NTRS1973

A unique high intensity solar simulation system

This simulator is unique in that it is capable of producing intensities up to 16.0 solar constants (25 solar constants without spectral filters) and closely simulates the solar spectrum over a 12 inch diameter area. The simulator is described and the capabilities, calibration, operational experiences, data collection, and safety considerations associated with this simulator are discussed.

Romanowski, L., Jr.↗
NASA NTRS1995

Development of a Prototype Simulation Executive with Zooming in the Numerical Propulsion System Simulation

A major difficulty in designing aeropropulsion systems is that of identifying and understanding the interactions between the separate engine components and disciplines (e.g., fluid mechanics, structural mechanics, heat transfer, material properties, etc.). The traditional analysis approach is to decompose the system into separate components with the interaction between components being evaluated by the application of each of the single disciplines in a sequential manner. Here, one discipline uses information from the calculation of another discipline to determine the effects of component coupling. This approach, however, may not properly identify the consequences of these effects during the design phase, leaving the interactions to be discovered and evaluated during engine testing. This contributes to the time and cost of developing new propulsion systems as, typically, several design-build-test cycles are needed to fully identify multidisciplinary effects and reach the desired system performance. The alternative to sequential isolated component analysis is to use multidisciplinary coupling at a more fundamental level. This approach has been made more plausible due to recent advancements in computation simulation along with application of concurrent engineering concepts. Computer simulation systems designed to provide an environment which is capable of integrating the various disciplines into a single simulation system have been proposed and are currently being developed. One such system is being developed by the Numerical Propulsion System Simulation (NPSS) project. The NPSS project, being developed at the Interdisciplinary Technology Office at the NASA Lewis Research Center is a 'numerical test cell' designed to provide for comprehensive computational design and analysis of aerospace propulsion systems. It will provide multi-disciplinary analyses on a variety of computational platforms, and a user-interface consisting of expert systems, data base management and visualization tools, to allow the designer to investigate the complex interactions inherent in these systems. An interactive programming software system, known as the Application Visualization System (AVS), was utilized for the development of the propulsion system simulation. The modularity of this system provides the ability to couple propulsion system components, as well as disciplines, and provides for the ability to integrate existing, well established analysis codes into the overall system simulation. This feature allows the user to customize the simulation model by inserting desired analysis codes. The prototypical simulation environment for multidisciplinary analysis, called Turbofan Engine System Simulation (TESS), which incorporates many of the characteristics of the simulation environment proposed herein, is detailed.

Reed, John A.↗
NASA NTRS1983

Development of a persistent chemical agent simulation system

A Persistent Chemical Agent Simulation System was developed (PCASS) to simulate, for force-on-force training exercises, the field environment produced by the presence of persistent chemical agents. Such a simulant system must satisfy several requirements to be of value as a training aid. Specifically, it must provide for realistic training which will generate competency in at least the following areas: (1) detection of the persistent agent presence; (2) proper use of protective equipment and procedures; (3) determination of the extent of contamination; and (4) decontamination of equipment and personnel.

Source record↗
NASA NTRS2013

A Cryogenic Fluid System Simulation in Support of Integrated Systems Health Management

Simulations serve as important tools throughout the design and operation of engineering systems. In the context of sys-tems health management, simulations serve many uses. For one, the underlying physical models can be used by model-based health management tools to develop diagnostic and prognostic models. These simulations should incorporate both nominal and faulty behavior with the ability to inject various faults into the system. Such simulations can there-fore be used for operator training, for both nominal and faulty situations, as well as for developing and prototyping health management algorithms. In this paper, we describe a methodology for building such simulations. We discuss the design decisions and tools used to build a simulation of a cryogenic fluid test bed, and how it serves as a core technology for systems health management development and maturation.

cryogenics↗
NASA NTRS1991

Simulating thin cirrus clouds in Observing System Simulation Experiments (OSSE) for LAWS

It was previously shown (Wood and Emmitt, 1990, 1991) that, by omitting the contribution of thin cirrus by the Observing System Simulation Experiments, will result in severe misrepresentation of both the frequency and the accuracy of wind observations in the upper troposphere. This paper estimates the presence of optically thin (tau less than 1.0) cirrus clouds by using model soundings in a cirrus cloud model. An example is presented showing the location of cirrus cloud profiles over North America for November 10, 1979, which were generated by the LAWS Simulation Model.

Emmitt, G. D.↗
NASA NTRS2004

High-Fidelity Full System Simulations

High-fidelity full system simulations have the potential for revolutionizing the way complex systems, such as propulsion systems for aerospace vehicles, are designed, developed, manufactured, and operated. Significant time and cost savings will result from simulations that will resolve deleterious component interactions early in the design process. In addition, innovative new system configurations will result from the use of new tools that enable designers to challenge traditional rules and practices. The major challenges to developing and implementing high-fidelity systems simulations are in reducing the time and effort required to build, execute, and analyze data for the high complex simulations. In addition, large scale testing with unique instrumentation is required to validate the simulations. The solution to these problems reside in the application of advanced information technologies to assist the user to effectively manage, process, and synthesize the vast amount of data. The following presentation describes in more detail the benefits of high-fidelity full system simulations, the challenges to developing and implementing large scale simulations, and one approach that is being followed by the NASA Glenn Research Center to overcome these challenges. In addition, topics for discussion by the panel and audience are suggested.

Lytle, John K.↗
NASA NTRS1996

An Integrated Approach To Payload System Simulation

This paper describes a payload system simulation implemented at JPL as part of a comprehensive mission simulation facility. The flight software function includes communication with other process modules, instrument control, and data management. The payload system simulation software consists of: a camera subsystem, a virtual world, and a mission visualization toolset.

dynamics model photometric model geological model ↗
NASA NTRS2002

A Novel Approach for Modeling Chemical Reaction in Generalized Fluid System Simulation Program

The Generalized Fluid System Simulation Program (GFSSP) is a computer code developed at NASA Marshall Space Flight Center for analyzing steady state and transient flow rates, pressures, temperatures, and concentrations in a complex flow network. The code, which performs system level simulation, can handle compressible and incompressible flows as well as phase change and mixture thermodynamics. Thermodynamic and thermophysical property programs, GASP, WASP and GASPAK provide the necessary data for fluids such as helium, methane, neon, nitrogen, carbon monoxide, oxygen, argon, carbon dioxide, fluorine, hydrogen, water, a hydrogen, isobutane, butane, deuterium, ethane, ethylene, hydrogen sulfide, krypton, propane, xenon, several refrigerants, nitrogen trifluoride and ammonia. The program which was developed out of need for an easy to use system level simulation tool for complex flow networks, has been used for the following purposes to name a few: Space Shuttle Main Engine (SSME) High Pressure Oxidizer Turbopump Secondary Flow Circuits, Axial Thrust Balance of the Fastrac Engine Turbopump, Pressurized Propellant Feed System for the Propulsion Test Article at Stennis Space Center, X-34 Main Propulsion System, X-33 Reaction Control System and Thermal Protection System, and International Space Station Environmental Control and Life Support System design. There has been an increasing demand for implementing a combustion simulation capability into GFSSP in order to increase its system level simulation capability of a liquid rocket propulsion system starting from the propellant tanks up to the thruster nozzle for spacecraft as well as launch vehicles. The present work was undertaken for addressing this need. The chemical equilibrium equations derived from the second law of thermodynamics and the energy conservation equation derived from the first law of thermodynamics are solved simultaneously by a Newton-Raphson method. The numerical scheme was implemented as a User Subroutine in GFSSP.

Sozen, Mehmet↗
NASA NTRS1990

Documentation for the token ring network simulation system

A manual is presented which describes the language features of the Token Ring Network Simulation System. The simulation system is a powerful simulation tool for token ring networks which allows the specification of various Medium Access Control (MAC) layer protocols as well as the specification of various features of upper layer ISO protocols. In addition to these features, it also allows the user to specify message and station classes virtually to any degree of detail desired. The choice of a language instead of an interactive system to specify network parameters was dictated by both flexibility and time considerations. The language was developed specifically for the simulation system, and is very simple. It is also user friendly in that language elements which do not apply to the case at hand are ignored rather than treated as errors.

Peden, Jeffery H.↗
NASA NTRS1973

Active optics simulation system

The active optics simulation system (AOSS) is a set of computer programs and associated software to be used in the development, design, and evaluation of a primary mirror control system for a large space telescope, (e.g., the tentatively proposed 3-meter telescope). The mathematical models of component subsystems and the solution of the physical processes that occur within the mirror surface control system were obtained, and based on these models AOSS simulates the behavior of the entire mirror surface control system as well as the behavior of the component subsystems. The program has a modular structure so that any subsystem module can be replaced or modified with minimum disruption of the rest of the simulation program.

Chi, C. H.↗