Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “suspensions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Method for Selecting Rotor Suspension Design Criteria

A method for selecting rotor suspension design criteria that allow rotors with internal friction to negotiate critical speeds and avoid subsynchronous internal friction instabilities is described. A rotor model of a test rotor with internal friction is created and used to calculate the test rotor’s critical speeds, mode shapes, Campbell plots, and the rotational speed corresponding to the stability boundary for a nominal set of suspension parameters. The test rotor model is then used to demonstrate the suspension design criteria selection method.

Damiano, Brian↗
DOE OSTI2020

Correlating inter-particle forces and particle shape to shear-induced aggregation/fragmentation and rheology for dilute anisotropic particle suspensions: A complementary study via capillary rheometry and in-situ small and ultra-small angle X-ray scattering

Predicting the stability of suspensions composed of anisotropic particles is difficult due to the complexity and interplay of hydrodynamic and colloidal forces. For example, it is not well understood how non-spherical particle shapes affect suspension-rheological responses. This study presents evidence showing how the stacking of boehmite platelets dispersed in aqueous solution leads to moderate shear thinning, even at low boehmite mass fractions. Wide angle X-ray, small angle X-ray, and ultra-small angle X-ray scattering were used to simultaneously monitor changes to the size and fractal dimensions of boehmite aggregates from 6 – 10,000 Å as the sample was recirculated through an in situ capillary rheometer. The latter also provided simultaneous measurements of the viscosity of the suspensions. Computational fluid dynamics modeling of the apparatus was used to provide a more rigorous analysis of the fluid flow. In addition to shear-induced aggregation/fragmentation correlated to a complicated balance between hydrodynamic and colloidal forces, the results indicate that orientationally-dependent interactions, arising from non-spherical boehmite aggregate sub-units, may explain the relatively large experimental viscosity when the hydrodynamic force is small compared to colloidal forces. Ultimately, the results from this study can provide a foundation for future work investigating particle shape effects on colloidal and hydrodynamics forces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Bridging microscopic dynamics and rheology in the yielding of charged colloidal suspensions

The yielding of soft materials is critical to many natural and industrial processes, yet experimental insights into microscopic aspects of yielding are limited. This study combines angle X-ray scattering, X-ray photon correlation spectroscopy, and in situ rheology (Rheo-SAXS-XPCS) with fast lubrication dynamics simulations to examine how interparticle interactions influence yielding in charged colloidal suspensions. By tuning attraction through salt addition, we compare repulsive and attractive systems under deformation. Repulsive suspensions yield uniformly with Andrade-like creep and minimal structural change. In contrast, attractive suspensions show complex behaviors, including shear banding, delayed yielding, and resolidification, governed by transient dynamics at shear band interfaces. These results directly link microscopic particle dynamics to macroscopic flow and demonstrate how interaction potentials control rheological behavior. This work offers a framework for designing soft materials with tailored properties for applications in coatings, food processing, drug delivery, and other technologies requiring precise mechanical control.

Molecular Dynamics Simulation↗
DOE OSTI2023

Rheology of dense fiber suspensions: Origin of yield stress, shear thinning, and normal stress differences

We explain the origins of yield stress, shear thinning, and normal stress differences in rigid fiber suspensions. We investigate the interplay between the hydrodynamic, noncontact attractive and repulsive, and interfiber contact interactions. The shear-thinning viscosity and finite yield stress obtained from the Immerse Boundary Method simulations are in quantitative agreement with experiential results from the literature. In this study, we show that attractive interactions result in yield stress and shear thinning rheology in the suspensions of rigid fibers. This is an important finding, given the ongoing discussion regarding the origin of the yield stress for suspensions of fibers. Finally, the ability of the proposed model to quantitatively predict the rheology is not limited to only shear thinning and yield stress but also extends to normal stresses.

42 ENGINEERING↗
DOE OSTI2020

Control of Vibration Systems with Mechanical Motion Rectifier and their Applications to Vehicle Suspension and Ocean Energy Harvester

Vibration control is a large branch in control research, because all moving systems may induce desired or undesired vibration. Due to the limitation of passive system’s adaptability and changing excitation input, vibration control brings the solution to change system dynamic with desired behavior to fulfill control targets. According to preference, vibration control can be separated into two categories: vibration reduction and vibration amplification. Lots of research papers only examine one aspect in vibration control. The thesis investigates the control development for both control targets with two different control applications: vehicle suspension and ocean wave energy converter. It develops control methods for both systems with simplified modeling setup, then followed by the application of a novel mechanical motion rectifier (MMR) gearbox that uses mechanical one-way clutches in both systems. The flow is from the control for common system to the control design for a specifically designed system. In the thesis, active (model predictive control: MPC), semi-active (Skyhook, skyhook-power driven damper: SHPDD, hybrid model predictive control: HMPC), and passive control (Latching Control) methods are developed for different applications or control performance comparison on single system. The thesis also studies about new type of system with switching mechanism, in which other papers do not talk too much and possible control research direction to deal with such complicated system in vibration control. The state-space modeling for both systems are provided in the thesis with detailed model of the MMR gearbox. From the simulation, it can be shown that in the vehicle suspension application, the controlled MMR gearbox can be effective in improving vehicle ride comfort by 29.2% compared to that of the traditional hydraulic suspension. In the ocean wave energy converter, the controlled MMR WEC with simple latching control can improve the power generation by 57% compared to the passive MMR WEC. Besides, the passive MMR WEC also shows its advantage on the passive direct drive WEC in power generation improvement. From the control development flow for the MMR system, the limitation of the MMR gearbox is also identified, which introduces the future work in developing active-MMR gearbox by using an electromagnetic clutch. Some possible control development directions on the active-MMR is also mentioned at the end of the thesis to provide reference for future works.

16 TIDAL AND WAVE POWER↗
DOE OSTI2022

Designing Stress-Adaptive Dense Suspensions Using Dynamic Covalent Chemistry

The non-Newtonian behaviors of dense suspensions are central to their use in technological and industrial applications and arise from a network of particle–particle contacts that dynamically adapt to imposed shear. Reported herein are studies aimed at exploring how dynamic covalent chemistry between particles and the polymeric solvent can be used to tailor such stress-adaptive contact networks, leading to their unusual rheological behaviors. Specifically, a room temperature dynamic thia-Michael bond is employed to rationally tune the equilibrium constant (K eq ) of the polymeric solvent to the particle interface. It is demonstrated that low Keq leads to shear thinning, while high K eq produces antithixotropy, a rare phenomenon where the viscosity increases with shearing time. It is proposed that an increase in K eq increases the polymer graft density at the particle surface and that antithixotropy primarily arises from partial debonding of the polymeric graft/solvent from the particle surface and the formation of polymer bridges between particles. Thus, the implementation of dynamic covalent chemistry provides a new molecular handle with which to tailor the macroscopic rheology of suspensions by introducing programmable time dependence. These studies open the door to energy-absorbing materials that not only sense mechanical inputs and adjust their dissipation as a function of time or shear rate but also can switch between these two modalities on demand.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Shape effects on the local dynamics of suspensions of spheroidal particles

The effect of shape on the dynamics of suspensions of non-spherical heavy particles is examined by fully resolved numerical simulations of oblate and prolate spheroids, as well as spheres, for a density ratio of ten, volume fractions ranging from 0.5% to 5%, and Reynolds numbers between 20 and 30. The dynamics is determined both by the interactions of the particles with the fluid as well as by collisions, with the number and importance of collisions increasing with volume fractions. A single isolated oblate or prolate spheroid falling under gravity generally falls broadside on, for the governing parameters examined here, and at low-volume fractions, the majority of particles in a suspension fall that way. At higher-volume fractions, the orientation is more random. The slip velocity decreases as the volume fraction increases for all shapes, as expected, but the effect of the shape is much less than seen for a single particle. Furthermore, this seems to be due to two effects. For all volume fractions, the most deformed particles cluster more than spheres and less deformed particles, which increases their slip velocity. As the concentration increases, the increased particle interactions also causes more particles to fall short side-on, which reduces the frontal area and the resulting drag, increasing the slip velocity. This second effect is, of course, absent for spherical particles.

42 ENGINEERING↗
DOE OSTI2020

Amphiphilic Block Copolymers for Flocculation and Hydrophobization of Legacy Waste Suspensions in Flotation Driven Dewatering Operations - 20162

Flotation has been effectively demonstrated as a low footprint, high efficiency separation process when utilising simple anionic surface modifying agents such as sodium dodecyl sulphate (SDS). These agents increase hydrophobicity to remove suspended cationic surface charged particulates such as Mg(OH){sub 2} from waste suspensions similar to those at British nuclear fuel management sites- where corrosion processes have degraded fuel cladding. The technology is advantageous as it could effectively be retrofitted into existing waste management facilities at nuclear waste management sites such Sellafield and Hanford as the simplicity (no moving parts) and size of this technology coupled with low cost of construction could be rapidly deployed to aid in risk and hazard reduction decommissioning operations with minimum impact to secondary waste generation. Previously, sodium dodecyl sulphate has been deployed as a collector agent to increase the hydrophobicity of Mg(OH){sub 2} suspended particles, achieving a maximum particulate extraction percentage of 93%. To achieve further particulate extraction, flotation performance has been determined to be a function of the hydrodynamic limitations extracting fine material (>20 μm). Fine particulates have been shown in the minerals industry to have an inability to overcome slipstreams created from rising bubbles in flotation cells, likely due to the low mass and thus momentum of the colloidal material, preventing interaction between the hydrophobized particles and air-water interfaces (bubbles). To combat this mass transfer resistance poly(acrylic acid)-block-poly(n-butyl acrylate) amphiphilic diblock copolymers were synthesised via reversible addition-fragmentation chain-transfer (RAFT) polymerisation. The anticipated mode of action of these polymers involves the hydrophilic poly(acrylic acid) block polymer acting as a flocculation agent to increase the mass of the aggregates, and the hydrophobic poly(n-butyl acrylate) modifies the hydrophobicity of the resulting flocs. The concentration of this polymer (termed a macro-collector) was varied and the change in particle size distribution of the particulate suspension was analysed using static light scattering. The flotation performance was then characterised by several methods including percentage particulate recovery, volume reduction factor and residual bulk particulate concentration. This was then benchmarked against the traditional surfactant collector agent SDS. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Effect of particle size on the capture of uranium oxide colloidal particles from aqueous suspensions via high-gradient magnetic filtration

The effectiveness of High Gradient Magnetic Filtration (HGMF) in capturing uranium oxide particles from suspensions was investigated in this study. Two sets of experiments were performed to evaluate the importance of size on the capture of uranium oxide particles. The first considered two batches sieved into size bins of< 5, 5–10, 10–15, and 15–20 µm, while the second was performed using two suspensions with diameters smaller than 1.0 µm and between 1.0 and 1.5 µm. Iron oxide experiments, with particles between 0.3 and 0.8 µm, were performed for calibration purposes. In all experiments, a surfactant (Triton-X100 or sodium dodecyl sulfate) was used to prevent particle aggregation and limit the influence of non-magnetic capture mechanisms. A magnetic field of approximately 1.1 Tesla was generated using a water cooled electromagnet. HGMF was performed using tubular filters packed with ferromagnetic stainless-steel wool. Of the initial four uranium oxide particle sizes, magnetic capture was only observed for particles with a diameter of less than 5 µm, while larger particles experienced no magnetic and minimal total capture. For particles with diameters smaller than 1.0 µm and between 1.0 and 1.5 µm, capture efficiencies increased by 39 ± 9% and 34 ± 6% respectively, solely due to the magnetic field. Although the magnetic force is proportional to particle diameter, the capture efficiency decreased as diameter increased. So these results suggest that Brownian diffusion, which is influential for micron sized particles and increases with decreasing particle size, is acting in conjunction with the magnetic force to influence the efficacy of HGMF for uranium oxide. This important finding underscores the effectiveness of Brownian diffusion in increasing the rate of collision between particles and collector fibers. A stochastic trajectory model was developed to incorporate the influence of Brownian motion on particle behavior and filter removal efficiency. Modeling results are discussed and compared for uranium and iron oxide particles.

42 ENGINEERING↗
DOE OSTI2023

High-gradient magnetic separation of colloidal uranium oxide particles from soil components in aqueous suspensions

The separation of uranium oxide (UO 2 ) particles from soil-surrogate particles in aqueous suspensions was achieved using filtration enhanced by a magnetic field. Enhanced attraction of paramagnetic UO 2 colloids to a ferromagnetic stainless-steel filter placed in a strong magnetic field arises because of the positive magnetic susceptibility of the particles and the high-gradient field generated near ferromagnetic fibers. Enhanced uptake of smaller particles over larger ones occurs through Brownian motion that promotes the collision of particles with the ferromagnetic fibers of the filter. Hence, this work focused on UO 2 particles in the colloidal size range. Experiments used a water-cooled electromagnet and an array of permanent magnets. Chemical analysis showed that the magnetic field increased the capture efficiency of uranium particles from a range of 27–53% with the magnet off up to 98% with the magnet on after a single pass of the suspension through the filter. Further, the recovery of the UO 2 particles from the filter, however, was more difficult to achieve. Small amounts of UO 2 , together with significant amounts of background SiO 2 particles, were removed from the filter during a first flush with the magnetic field on. A much larger recovery of UO 2 was not observed until a second out-of-field flush was performed, which also released some SiO 2 . The degree to which particle separation was enhanced through the use of multi-stage filtration compared to single pass-through filtration was also examined. A design was suggested that could be used to optimize the separation efficiency for a continuous process.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2020

Controlled 3D nanoparticle deposition by drying of colloidal suspension in designed thin micro-porous architectures

Nanoparticle deposition by drying of colloidal suspension in thin micro-porous architectures has attracted a lot of attention in scientific research as well as industrial applications. However, the underlying mechanisms of such three-dimensional (3D) deposition are not yet fully revealed due to the complexity of the co-occurring processes of two-phase fluid flows, phase change and mass transport. Consequently, the control of 3D nanoparticle deposition remains a challenge. We use a combined experimental and numerical approach to achieve controlled 3D nanoparticle deposition by drying of colloidal suspension in two pillar-based thin micro-porous architectures. By the design of pillar layout, rectangular-spiral and circular-spiral deposition configurations are obtained globally. By varying the surface wettability, vertically symmetric and sloped nanoparticle depositions can be achieved locally. While the numerical modeling reveals the mechanisms of liquid internal flow, as well as the impact of local drying rate on nanoparticle transport, accumulation and final deposition, the experimental results of deposition configurations validate the controlling strategies. This combined experimental and numerical work provides a framework to achieve desired 3D nanoparticle deposition in thin micro-porous architectures, with a thorough understanding of the underlying mechanisms of two-phase fluid flows, phase change and mass transport.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Hydrodynamics of thermally driven chiral suspensions

Considerable effort has been directed towards the characterization of chiral mesoscale structures, as shown in chiral protein assemblies and carbon nanotubes. Here, we establish a thermally driven hydrodynamic description for the actuation and separation of mesoscale chiral structures in a fluid medium. Cross-flow of a Newtonian liquid with a thermal gradient gives rise to an effective torque that propels each particle of a chiral suspension according to its handedness. In turn, the chiral suspension alters the liquid flow, which thus acquires a transverse (chiral) velocity component. Since observation of the predicted effects requires a low degree of sophistication, our work provides an efficient and inexpensive approach to test and calibrate chiral particle propulsion and separation strategies.

Mechanics↗
DOE OSTI2025

Turbulent-like flows in quasi two-dimensional dense suspensions of motile colloids

Dense bacterial suspensions exhibit turbulent-like flows at low Reynolds numbers, driven by the activity of the microswimmers. In this study, we develop a model system to examine these dynamics using motile colloids that mimic bacterial locomotion. The colloids are powered by the Quincke instability, which causes them to spontaneously roll in a random-walk pattern when exposed to a square-wave electric field. We experimentally investigate the flow dynamics in dense suspensions of these Quincke random walkers under quasi two-dimensional conditions, where the particle size is comparable to the gap between the electrodes. The results suggest a scaling regime in the energy spectrum ∼k −4 at high wavenumbers, observed consistently across activity levels and particle concentrations. We observe that velocity time correlations decay within a single period of the square-wave field, yet an anti-correlation appears between successive field applications, indicative of a dynamic structural memory of the ensemble.

Luo, Rui [Northwestern Univ., Evanston, IL (United↗
DOE OSTI2020

Microscopic ergodicity breaking governs the emergence and evolution of elasticity in glass-forming nanoclay suspensions

We report a study combining x-ray photon correlation spectroscopy (XPCS) with in situ rheology to investigate the microscopic dynamics and mechanical properties of aqueous suspensions of the synthetic hectorite clay Laponite, which is composed of charged, nanometer-scale, disk-shaped particles. The suspensions, with particle concentrations ranging from 3.25 to 3.75 wt%, evolve over time from a fluid to a soft glass that displays aging behavior. The XPCS measurements characterize the localization of the particles during the formation and aging of the soft-glass state. The fraction of localized particles f 0 increases rapidly during the early formation stage and grows more slowly during subsequent aging, while the characteristic localization length r loc steadily de- creases. Despite the strongly varying rates of aging at different concentrations, both f 0 and r loc scale with the elastic shear modulus G' in a manner independent of concentration. During the later aging stage, the scaling between r loc and G' agrees quantitatively with a prediction of naive mode coupling theory. Breakdown of agreement with the theory during the early formation stage indi- cates the prevalence of dynamic heterogeneity, suggesting the soft solid forms through precursors of dynamically localized clusters.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Unifying disparate rate-dependent rheological regimes in non-Brownian suspensions

A typical dense non-Brownian particulate suspension exhibits shear thinning (decreasing viscosity) at low shear rate/stress followed by a Newtonian plateau (constant viscosity) at intermediate shear rate/stress values which transitions to shear thickening (increasing viscosity) beyond a critical shear rate/stress value and finally, undergoes a second shear thinning transition at extremely high shear rate/stress values. In this study, we unify and quantitatively reproduce all the disparate rate dependent regimes and the corresponding transitions for a dense non-Brownian suspension with increasing shear rate/stress. Here, we employ discrete particle dynamics simulations based on the proposed mechanism to elucidate its accuracy. We find that a competition between inter-particle interactions of hydrodynamic and non-hydrodynamic origins and the switching in the dominant stress scale with increasing the shear rate/stress lead to each of the above transitions. Inclusion of traditional hydrodynamic interactions, attractive/repulsive DLVO (Derjaguin and Landau, Verwey and Overbeek) interactions, the inter-particle contact interactions and a constant friction (or other constraint mechanism) reproduce the initial thinning as well as the shear thickening transition. However, to quantitatively capture the intermediate Newtonian plateau and the second shear thinning, an additional non-hydrodynamic interaction of non-DLVO origin and a decreasing coefficient of friction, respectively, are essential; thus, providing the first explanation for the presence of the intermediate Newtonian plateau along with reproducing the second shear thinning in a single framework. Expressions utilized for various interactions and friction are determined from experimental measurements and hence, result in an excellent quantitative agreement between the simulations and previous experiments.

42 ENGINEERING↗
DOE OSTI2020

Shear Thickening and Jamming of Dense Suspensions: The "Roll" of Friction.

Particle-based simulations of discontinuous shear thickening (DST) and shear jamming (SJ) suspensions are used to study the role of stress-activated constraints, with an emphasis on resistance to gearlike rolling. Rolling friction decreases the volume fraction required for DST and SJ, in quantitative agreement with real-life suspensions with adhesive surface chemistries and "rough" particle shapes. It sets a distinct structure of the frictional force network compared to only sliding friction, and from a dynamical perspective leads to an increase in the velocity correlation length, in part responsible for the increased viscosity. The physics of rolling friction is thus a key element in achieving a comprehensive understanding of strongly shear-thickening materials.

Singh, Abhinendra↗
DOE OSTI2020

Hyperuniform Structures Formed by Shearing Colloidal Suspensions

In periodically sheared suspensions there is a dynamical phase transition, characterized by a critical strain amplitude $γ_c$, between an absorbing state where particle trajectories are reversible and an active state where trajectories are chaotic and diffusive. Repulsive nonhydrodynamic interactions between “colliding” particles’ surfaces have been proposed as a source of this broken time reversal symmetry. A simple toy model called random organization qualitatively reproduces the dynamical features of this transition. Random organization and other absorbing state models exhibit hyperuniformity, a strong suppression of density fluctuations on long length scales quantified by a structure factor $S(q → 0) ~q^α$ with $\textit{α}$ > 0, at criticality. In this work, we show experimentally that the particles in periodically sheared suspensions organize into structures with anisotropic short-range order but isotropic, long-range hyperuniform order when oscillatory shear amplitudes approach $γ_c$.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Microscopic activated dynamics theory of the shear rheology and stress overshoot in ultradense glass-forming fluids and colloidal suspensions

We formulate a particle and force level, activated dynamics-based statistical mechanical theory for the continuous startup nonlinear shear rheology of ultradense glass-forming hard sphere fluids and colloidal suspensions in the context of the elastically collective nonlinear Langevin equation approach and a generalized Maxwell model constitutive equation. Activated structural relaxation is described as a coupled local-nonlocal event involving caging and longer range collective elasticity which controls the characteristic stress relaxation time. Theoretical predictions for the deformation-induced enhancement of mobility, the onset of relaxation acceleration at remarkably low values of stress, strain, or shear rate, apparent power law thinning of the steady-state structural relaxation time and viscosity, a nonvanishing activation barrier in the shear thinning regime, an apparent Herschel–Buckley form of the shear rate dependence of the steady-state shear stress, exponential growth of different measures of a yield or flow stress with packing fraction, and reduced fragility and dynamic heterogeneity under deformation were previously shown to be in good agreement with experiments. The central new question we address here is the defining feature of the transient response—the stress overshoot. In contrast to the steady-state flow regime, understanding the transient response requires an explicit treatment of the coupled nonequilibrium evolution of structure, elastic modulus, and stress relaxation time. We formulate a new quantitative model for this aspect in a physically motivated and computationally tractable manner. Theoretical predictions for the stress overshoot are shown to be in good agreement with experimental observations in the metastable ultradense regime of hard sphere colloidal suspensions as a function of shear rate and packing fraction, and accounting for deformation-assisted activated motion appears to be crucial for both the transient and steady-state responses.

Mechanics↗