Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “suspensions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Properties of silicon suspensions and slip-cast bodies

The effect of varying pH, sonication times, and solid loading of silicon powder suspensions on the properties of powder/water suspensions and on the resulting pore characteristics of slip-cast bodies was studied. Aqueous suspensions of ground an aged silicon powder (of 0.3 micron median Stokes diameter and containing 1.3 vol pct Fe2O3 powder) were prepared, with solids loading in the range of 30-56 vol pct, and were adjusted to varying pH values by addition of either HCl or NH4OH or NaOH. Suspension aliquots were sonicated for 0, 15, 30, or 60 min. Suspensions were characterized by zeta potentials, ionic strength, and viscosity. Pore characteristics of cast bodies were determined by mercury porosimetry. It was found that intermediate pH values (pH 7-9), long sonication (60 min), and high solid loadings (56 vol pct) produced samples with highest green densities and smallest median pore radius.

Sacks, M. D.↗
NASA NTRS1991

Low-Frequency Suspension System For Large Space Structures

Simple system enables vibration testing of space structures on ground. Suspension system includes number of suspension stations attached by cables to space structure (such as truss beam) along its length. Suspension stations fixed to ceiling or other rigid support. Disk and cable adjustments lower frequency of oscillatory motion of suspension system to enable accurate measurements of frequencies of vibration of space structure. Designed to alleviate coupling between suspension system and torsional vibrational modes of structure.

Reed, Wilmer H., III↗
NASA NTRS1991

Nonlinear compensation techniques for magnetic suspension systems

In aerospace applications, magnetic suspension systems may be required to operate over large variations in air-gap. Thus the nonlinearities inherent in most types of suspensions have a significant effect. Specifically, large variations in operating point may make it difficult to design a linear controller which gives satisfactory stability and performance over a large range of operating points. One way to address this problem is through the use of nonlinear compensation techniques such as feedback linearization. Nonlinear compensators have received limited attention in the magnetic suspension literature. In recent years, progress has been made in the theory of nonlinear control systems, and in the sub-area of feedback linearization. The idea is demonstrated of feedback linearization using a second order suspension system. In the context of the second order suspension, sampling rate issues in the implementation of feedback linearization are examined through simulation.

Trumper, David L.↗
NASA NTRS1992

Space applications of diamagnetic suspensions

Conventional noncontact magnetic suspensions require power and sensor feedback to maintain stability of the levitated object. Magnetic suspensions using superconductors require neither power nor feedback for stability but must be maintained at low temperatures. This paper discusses a little known type of magnetic bearing that does not require power, sensor feedback, or cooling: diamagnetic suspension. While the bearing pressure for diamagnetic suspensions is typically limited to 1 g/sq cm, their simplicity, environmental tolerances, and wide range of material choices suggest that they may be useful for a number of space applications. This paper discusses the fundamentals of diamagnetic suspensions as well as their potential space applications.

Pelrine, Ronald E.↗
NASA NTRS1994

Spring- And Air-Suspension Mechanism For Testing Structures

Spring-and air-suspension mechanism supports weight of one end of test structure, yet allows that end to move almost completely unhindered as though it were weightless and not attached to suspension. Mechanisms of this type called "zero-spring-rate mechanisms" (ZSRM's) because they support structure in manner of spring suspension exhibiting approximately zero stiffness (zero spring rate) within some range of motion about nominal equilibrium or central support position. This suspension mechanism does not include overhead cables, which necessitate large amounts of overhead clearance and overhead support structures: suspension mechanism more compact (much smaller than structure) and supports structure from below.

Woodard, Stanley E.↗
NASA NTRS1996

Computational Analysis of Static and Dynamic Behaviour of Magnetic Suspensions and Magnetic Bearings

Static modelling of magnetic bearings is often carried out using magnetic circuit theory. This theory cannot easily include nonlinear effects such as magnetic saturation or the fringing of flux in air-gaps. Modern computational tools are able to accurately model complex magnetic bearing geometries, provided some care is exercised. In magnetic suspension applications, the magnetic fields are highly three-dimensional and require computational tools for the solution of most problems of interest. The dynamics of a magnetic bearing or magnetic suspension system can be strongly affected by eddy currents. Eddy currents are present whenever a time-varying magnetic flux penetrates a conducting medium. The direction of flow of the eddy current is such as to reduce the rate-of-change of flux. Analytic solutions for eddy currents are available for some simplified geometries, but complex geometries must be solved by computation. It is only in recent years that such computations have been considered truly practical. At NASA Langley Research Center, state-of-the-art finite-element computer codes, 'OPERA', 'TOSCA' and 'ELEKTRA' have recently been installed and applied to the magnetostatic and eddy current problems. This paper reviews results of theoretical analyses which suggest general forms of mathematical models for eddy currents, together with computational results. A simplified circuit-based eddy current model proposed appears to predict the observed trends in the case of large eddy current circuits in conducting non-magnetic material. A much more difficult case is seen to be that of eddy currents in magnetic material, or in non-magnetic material at higher frequencies, due to the lower skin depths. Even here, the dissipative behavior has been shown to yield at least somewhat to linear modelling. Magnetostatic and eddy current computations have been carried out relating to the Annular Suspension and Pointing System, a prototype for a space payload pointing and vibration isolation system, where the magnetic actuator geometry resembles a conventional magnetic bearing. Magnetostatic computations provide estimates of flux density within airgaps and the iron core material, fringing at the pole faces and the net force generated. Eddy current computations provide coil inductance, power dissipation and the phase lag in the magnetic field, all as functions of excitation frequency. Here, the dynamics of the magnetic bearings, notably the rise time of forces with changing currents, are found to be very strongly affected by eddy currents, even at quite low frequencies. Results are also compared to experimental measurements of the performance of a large-gap magnetic suspension system, the Large Angle Magnetic Suspension Test Fixture (LAMSTF). Eddy current effects are again shown to significantly affect the dynamics of the system. Some consideration is given to the ease and accuracy of computation, specifically relating to OPERA/TOSCA/ELEKTRA.

Britcher, Colin P.↗
NASA NTRS1997

Research Related to Multi Degree of Freedom Magnetic Suspensions

This thesis covers the activities associated with (1) recommissioning of the 6-inch Magnetic Suspension and Balance System (MSBS) and (2) enhancing the Annular Suspension and Pointing System (ASPS). These activities continue the program of research in the multi degree of freedom magnetic suspension program at Old Dominion University. The 6-inch MSBS is a large gap magnetic suspension system used as a model support and balance system in wind tunnels. The first stage of recommissioning of the 6-inch MSBS for the 6-inch subsonic wind tunnel is performed. Experimental data and computational results for the magnetic field distribution of the MSBS are given and compared with the estimated magnetic field strength. The comparison indicates that the magnet system is still operating as designed. The Electromagnetic Position Sensor used in the 6-inch MSBS is analyzed before its find reinstatement. The ASPS is a small gap magnetic suspension system providing orientation, mechanical isolation and fine pointing of space payloads. The control system of the ASPS is improved by designing a new code to realize red time control over the system. The original Proportional-Derivative controller is upgraded to a Proportional-Integral-Derivative controller. This progress leads to a system which is more stable and robust with less noise. This new controller is generic and can be adapted to the 6-inch MSBS. Finally, future work on these two systems is proposed.

Britcher, Colin↗
NASA NTRS1991

Effects of suspension-induced osteopenia on the mechanical behaviour of mouse long bones

Whereas most studies of tail-suspension induced osteopenia have utilized rat femora, the present study investigated the effects of a 14 day tail-suspension on the mechanical behaviour of mice femora, tibiae and humeri. Force-deflection properties were obtained via three-point bending for long bones from suspended and control mice. Whole bone behaviour was characterized by converting the force-deflection values to stiffness, strength, ductility and energy parameters which were not normalized for specimen geometry. The effects of a systematic variation in the deflection rate over the range 0.1-10 mm min-1 were also evaluated. Statistical analysis indicated that the primary effect of the tail-suspension period was lowered bone mass which was manifested mechanically through lower values of the bone strength parameters. These effects were similar in the bones of both the fore and hind limbs. The results also demonstrated that the stiffness, ductility and energy characteristics were much less influenced by the tail-suspension. Whereas a significant dependence of the bone strength values upon deflection rate was observed for the femora and humeri, the other mechanical parameters were less sensitive. Based upon the nature of the physical and mechanical changes observed in the long bones following tail-suspension, the mouse appears to be a suitable animal model for the study of osteopenia.

NASA Discipline Number 93-10↗
NASA NTRS1994

Influence of antiorthostatic suspension on resistance to murine Listeria monocytogenes infection

The present study was designed to evaluate the influence of antiorthostatic suspension, a ground-based modeling system employed to simulate certain aspects of weightlessness that occur during space flight, on the capacity of mice to resist infection with the facultative intracellular bacterial pathogen Listeria monocytogenes. Female BDF1 mice were suspended by the tail in the orthostatic or antiorthostatic position and were infected with a sublethal dose of virulent L. monocytogenes at various times during the suspension. It was found that suspension did not influence the kinetics of bacterial growth in vivo if the infection was started concurrently with the suspension. However, mice that were antiorthostatically suspended 2, 4, or 7 days before the onset of infection exhibited an enhanced capacity to eliminate the challenge infection. Suspending mice on day 2 of the infection did not alter the kinetics of bacterial growth. Finally, the enhancement of resistance to the primary Listeria infection was accompanied by failure of the mice to generate long-term protective immunological memory to the challenge organism. Collectively, these results indicate that the stress of antiorthostatic suspension can influence the capacity of mice to resist bacterial infection.

NASA Discipline Regulatory Physiology↗
NASA NTRS2004

Novel Optical Diagnostic Techniques for Studying Particle Contact and Deposition Upon a Large Cylinder in a Sheared Suspension

The objectives of this research project were: 1) To study the fluid dynamics of sheared particle-liquid suspensions and the impact of differential particle-fluid inertia; 2) To develop new techniques for observing suspension particle contact and deposition upon solid surfaces. Dr. Yoda was supported by the NASA Office of Biological and Physical Research on a four-year grant from March 2000 through November 2004 for a ground-based study on the fluid dynamics of sheared particle-liquid suspensions and the impact of differential particle-fluid inertia on such flows. Such inertial effects can only be observed in reduced-gravity environments since they are overwhelmed by buoyancy effects on Earth. Moreover, these inertial effects will have a significant impact upon suspension flows in microgravity. Suspension dynamics are of importance in a wide variety of advanced life systems applications, including water reclamation and dust mitigation in confined habitats.

Rashidnia, Nasser↗
DOE OSTI2023

Rheology of concentrated fiber suspensions with a load-dependent friction coefficient

Here we investigate the effects of fiber aspect ratio, roughness, flexibility, and volume fraction on the rheology of concentrated suspensions in a steady shear flow using direct numerical simulations. We model the fibers as inextensible continuous flexible slender bodies with the Euler-Bernoulli beam equation governing their dynamics suspended in an incompressible Newtonian fluid. The fiber dynamics and fluid flow coupling is achieved using the immersed boundary method. In addition, the fiber surface roughness might lead to interfiber contacts, resulting in normal and tangential forces between the fibers, which follow Coulomb’s law of friction. The surface roughness is modeled as hemispherical protrusions on the fiber surfaces. Their deformation results in a normal load-dependent friction coefficient. Our simulations accurately predict the experimentally observed shear thinning in fiber suspensions. Furthermore, we find that the suspension viscosity η increases with increasing the volume fraction, roughness, fiber rigidity, and aspect ratio. The increase in η is the macroscopic manifestation of a similar increase in the microscopic contact contribution to the total stress with these parameters. In addition, we observe positive and negative first N 1 and second N 2 normal stress differences, respectively, with |N 2 | < |N 1 |, in agreement with previous experiments. Last, we propose a modified Maron-Pierce law to quantify the reduction in the jamming volume fraction by increasing the fiber aspect ratio and roughness. Our results and analysis establish the use of fiber surface tribology to tune the suspension flow behavior.

42 ENGINEERING↗
DOE OSTI2020

Unstable Invasion of Sedimenting Granular Suspensions

Here we investigate the development of mobility inversion and fingering when a granular suspension is injected radially between horizontal parallel plates of a cell filled with a miscible fluid. While the suspension spreads uniformly when the suspension and the displaced fluid densities are exactly matched, even a small density difference is found to result in a dense granular front which develops fingers with angular spacing that increase with granular volume fraction and decrease with injection rate. We show that the timescale over which the instability develops is given by the volume fraction dependent settling timescale of the grains in the cell. We then show that the mobility inversion and the nonequilibrium Korteweg surface tension due to granular volume fraction gradients determine the number of fingers at the onset of the instability in these miscible suspensions.

02 PETROLEUM↗
DOE OSTI2023

A review of the shear rheology of carbon black suspensions

The microstructural link to the rheology of carbon black suspensions has recently become clear as a result of advances in computational and experimental methods. This understanding reveals the important role of the restructuring, build-up, and break-up of carbon black agglomerates in simple shear, rationalized by a dimensionless balance of the hydrodynamic forces acting to break the agglomerates apart against the cohesive forces holding them together (i.e., the Mason number). The Mason number not only can predict the origin of reversible thixotropy seen in carbon black suspensions observed at higher shear intensities, but can also be used to rationalize the evolution of microstructure at lower shear intensities. This review focuses on carbon black suspension behavior, but the insights derived from carbon black suspensions are broadly applicable to a diverse class of soft matter including colloidal gels relevant to a variety of applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Tailoring the rheological properties of high protein suspension by thermal-mechanical treatment

The viscoelasticity of concentrated protein suspensions associates closely with the mixing efficiency and cleaning frequency of facility during high-protein food development. This study investigated the effects of thermal-mechanical treatment on the viscoelasticity of milk protein isolate (MPI) suspensions and their underlying mechanisms to develop protein ingredient with low viscoelasticity. MPI suspensions (20%) were treated at 25, 50 and 85°C for 10-60 min under constant shear (100 s -1 ), followed by storage at 4°C. The viscosity (η) of MPI suspension treated at 50°C and 85°C was similar to 1-10% as those treated at 25 ° C. After four days of storage at 4°C, η showed the least value in 50°C-treated samples compared to those at 25 ° C and 85 ° C. The η and storage modulus (G') was decreased with prolonged treatment at 25 and 50°C, whereas opposite trend was found in 85°C treated samples. Differential scanning calorimetry found proteins in 50°C treated samples had smaller enthalpy than those in the control and 25°C treated samples. Protein surface hydrophobicity was increased slightly from 25°C to 50°C, but remarkably in 85°C treated samples. Ultra-small angle x-ray scattering showed the radius of gyration (R-g) of casein micelle was similar to 38 nm at 25°C and 50°C treated samples but increased to similar to 44 nm 85°C treated samples with reduced compactness. A new sphere-like structure with R-g of 18 nm was generated in 85°C treated samples. These findings suggested modulating temperature during thermal-mechanical treatment is essential to alter protein structures and morphology for desirable rheological properties.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Connecting particle interactions to agglomerate morphology and rheology of boehmite nanocrystal suspensions

Rheology imposes significant challenges on processing of complex suspensions such as nuclear waste slurries at the Hanford and Savannah River sites. Understanding rheology connecting to microstructures and underlying particle interactions in complex slurries is therefore important for both fundamental knowledge and practical applications. Here, we use suspensions of aluminum oxyhydroxide minerals in the form of boehmite as an analog of the radioactive waste slurry to gain physical insights on the correlation between particle interactions, microstructures, and slurry rheology. Specifically, we use a combination of Couette rheometry and small-angle scattering techniques (independently and simultaneously) to understand how the slurry microstructure changes under flow and how these structural changes manifest themselves in the bulk rheology of the suspensions. Our experiments show that the boehmite slurries are thixotropic, with the rheology and structure of the suspensions changing with increasing exposure to flow. In the slurries, particle aggregates begin as loose, system-spanning clusters, but exposure to moderate shear rates causes the aggregates to irreversibly consolidate into denser clusters of finite size. The microstructural changes directly influence the rheological properties of the slurries such as viscosity and viscoelasticity. More importantly, our study shows that solution pH affects the amount of structural rearrangement and the kinetics of the rearrangement process, with an increase in pH leading to faster and more dramatic changes in the bulk rheology. Such dynamic microstructural changes and resultant rheology are understood via correlations between particle interactions and strength of particle network, coupled with surface chemistry and anisotropic nature of particle interactions. Nearly identical structural changes are also observed in Poiseuille flow geometries, implying that the observed changes are relevant in the pipe flow conditions present during waste processing.

Weston, Javen S.↗
DOE OSTI2023

Hydrodynamic irreversibility of non-Brownian suspensions in highly confined duct flow

The irreversible behaviour of a highly confined non-Brownian suspension of spherical particles at low Reynolds number in a Newtonian fluid is studied experimentally and numerically. In the experiment, the suspension is confined in a thin rectangular channel that prevents complete particle overlap in the narrow dimension and is subjected to an oscillatory pressure-driven flow. In the small cross-sectional dimension, particles rapidly separate to the walls, whereas in the large dimension, features reminiscent of shear-induced migration in bulk suspensions are recovered. Furthermore, as a consequence of the channel geometry and the development and application of a single-camera particle tracking method, three-dimensional particle trajectories are obtained that allow us to directly associate relative particle proximity with the observed migration. Companion simulations of a steadily flowing suspension highly confined between parallel plates are conducted using the force coupling method, which also show rapid migration to the walls as well as other salient features observed in the experiment. While we consider relatively low volume fractions compared to most prior work in the area, we nevertheless observe significant and rapid migration, which we attribute to the high degree of confinement.

42 ENGINEERING↗
DOE OSTI2022

Tailored Mesoporous Microspheres by Polymerization-Induced Microphase Separation in Suspension

We describe the preparation of block polymer beads by aqueous suspension polymerization to create poly(caprolactone) (PCL)-block-poly(styrene-co-divinylbenzene) beads that can be selectively etched under basic conditions to yield mesoporous polymer microspheres with uniform pore size. Polyvinylalcohol was used to stabilize the suspension polymerization in which styrene and divinylbenzene monomers were polymerized from a PCL macrochain transfer agent (macroCTA). The resulting polymerization-induced microphase separation process led to a nanostructured bicontinuous morphology. The particle size and pore size were independently tunable: the particle size was controlled by the stir rate of the suspension polymerization-yielding average diameters ranging from 60 to 300 μm-while the pore size was determined by the molar mass of the PCL block, with the mode pore diameters being 6 nm and 11 nm after etching beads made using 13 and 45 kg/mol PCL blocks, respectively. Based on nitrogen sorption measurements, the surface areas of the beads were ~300 m 2 /g when using a PCL macroCTA of 13 kg/mol. The beads were homogenous throughout on the micron length scale as determined by confocal Raman microscopy and lacked an impermeable skin layer as confirmed by scanning electron microscopy. Furthermore, the scalability of suspension polymerization allows for the simple synthesis of large quantities of thermoset microspheres with uniform pore size. We also demonstrate the ability to incorporate functional pore walls into the beads using multiblock precursor polymers. These functionalized mesoporous polymer beads show high affinity for ionic dyes in aqueous solutions (as a proof of principle) and remove dye from the solution at rates exceeding those of commercial ion-exchange resins. The developed procedure could be used to generate other functional surface chemistries with important applications in heterogeneous catalysis, chromatography, and water remediation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Suspension electrolyte with modified Li + solvation environment for lithium metal batteries

Designing a stable solid–electrolyte interphase on a Li anode is imperative to developing reliable Li metal batteries. In this work, we report a suspension electrolyte design that modifies the Li + solvation environment in liquid electrolytes and creates inorganic-rich solid–electrolyte interphases on Li. Li 2 O nanoparticles suspended in liquid electrolytes were investigated as a proof of concept. Through theoretical and empirical analyses of Li 2 O suspension electrolytes, the roles played by Li 2 O in the liquid electrolyte and solid–electrolyte interphases of the Li anode are elucidated. Also, the suspension electrolyte design is applied in conventional and state-of-the-art high-performance electrolytes to demonstrate its applicability. Based on electrochemical analyses, improved Coulombic efficiency (up to ~99.7%), reduced Li nucleation overpotential, stabilized Li interphases and prolonged cycle life of anode-free cells (~70 cycles at 80% of initial capacity) were achieved with the suspension electrolytes. We expect this design principle and our findings to be expanded into developing electrolytes and solid–electrolyte interphases for Li metal batteries.

25 ENERGY STORAGE↗