Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface wetting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Computational Thermal Hydraulics of a High-Performance Low-Enriched-Uranium Annular Target for HFIR Irradiation

Molybdenum-99 has historically been generated via isolation from fissioned highly enriched uranium (HEU) targets. Here, this isotope is in high demand due to its daily use across the world in radiopharmaceutical medical procedures. The primary objective of this work was to design and analyze an experimental target assembly containing one low-enriched-uranium (LEU) annular target for irradiation at the High Flux Isotope Reactor (HFIR). Efforts included incorporating spatially dependent energy sources from neutron and gamma interactions, quantifying thermal contact conductance at material interfaces, performing grid-independent studies, comparing turbulence models, and simulating various steady-state and transient scenarios relevant for irradiation qualification and eventual insertion. These models provide velocity, pressure, and temperature distributions in both space and time. Such results enable the selection of an appropriate irradiation location, fission rate density, and flow-limiting orifice size and demonstrate compliance with HFIR safety requirements such that insertion into the reactor can be approved. This analysis shows that across all scenarios, wetted surface temperatures remain below the coolant saturation temperature with no net vapor formation in the coolant. In every scenario, all components stay below 30% of the aluminum 6061 melting temperature. Computational fluid dynamics and system-level models predict peak target temperatures that agree within 4%, though the predicted axial location of the peak differs by about 10% of the heated length due to differences in flow development length. These results de-risk the irradiation of LEU (annular targets) and strengthen a domestic, HEU-independent 99 Mo supply by providing important fuel performance data to form the foundation for a robust licensing basis.

Molybdenum-99↗
DOE OSTI2025

Continued Testing and Modeling of the AirSquared All-Metal Tritium Scroll Pump

The implementation of fusion energy requires the processing of the deuterium-tritium mixture used to fuel the reaction. Many gas processing operations require either a gas-motive force or a pressure gradient across a system; both are achieved using vacuum pumps. However, because of the material challenges of working with tritium, specialized pumps are required that use only metal on wetted surfaces. This prevents tritium retention and degradation of materials such as oils and polymers and reduces the generation of tritiated waste. Typical gas handling systems for tritium operations involve metal bellows pumps, all-metal scroll pumps, and metal turbomolecular pumps, depending on the pressure requirements. With the industry standard Normetex Type 15 m 3 /h (typically referred to as the Normetex 15) pump no longer available, the fusion market requires viable alternatives. In this study, we test an American-made pump, the AirSquared V16H034A-C01, and compare its performance to the Normetex. A performance model of the AirSquared pump is also produced, which can be applied to general process models to generate an accurate description of pressures and flows through various unit operations.

08 HYDROGEN↗
DOE OSTI2026

OC7 Project Phase II: Code Comparison and Experimental Validation of Hydroelastic Effects and Member-Level Loads in Floating Structures

This paper presents results from Phase II of the OC7 project, focusing on hydroelastic modeling and member-level load prediction for a flexible floating offshore structure. Numerical predictions from 11 academic and industrial partners are validated against experimental measurements obtained from a 1:70-scale test of the VolturnUS-S semisubmersible platform. A comprehensive set of verification and validation cases is examined. The results demonstrate that hydrodynamic added mass has a significant impact on predicted elastic natural frequencies. Under regular wave excitation, the numerical models reproduce platform motions and mooring line tensions with good accuracy. Member-level loads are also predicted with reasonable accuracy. Some discrepancies are observed for potential-flow models not accounting for higher-order effects associated with the instantaneous wetted surface.

17 WIND ENERGY↗
DOE OSTI2020

Status Update: Deposition Modeling For SNF Canister CISCC

This report fulfills the M3 milestones M3SF-21PN010207025 & M3SF-20PN0102070412. During fiscal year (FY) 2020, Pacific Northwest National Laboratory (PNNL) worked to further develop the FY 2019 deposition and particle tracking models. This status report outlines these efforts and presents the progress made so far. Model development work is ongoing and is planned to continue in FY 2021. The FY 2020 model development included work on: Wind Effects. Model development and sensitivity studies, investigated how wind direction and speed affect deposition; Brownian Motion. Implementing Brownian Motion into existing models; Particle Size Variability. Depending on the particle composition, the diameter of the particle may vary with changes in relative humidity. Models were developed to analyze this; Multiphase and Fluid Film Modeling. Investigating canister surface wetting and drying, and how this effects overall deposition. Models were developed to analyze this; Difusophoresis. Performing initial work to implement diffusiophoresis into the existing models; Turbophoresis. Performing initial work to implement turbophoresis into the existing models. Much of this work will continue into FY21. The authors present initial results and discus current and future work.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Laser Driven Hydrothermal Processing (LDHP) for Rapid Dissolution of Glassy Nuclear Debris

Discovered in 2009 on the SLAB laser system at LLNL, Laser-Driven Hydrothermal Processing (LDHP) both spalls and transiently dissolves a wetted surface (e.g., rock, concrete, paint) when that surface is struck by a laser beam pulse under specific conditions. Previous projects have explored the application of LDHP to expediting sample dissolution for post-detonation nuclear forensics. Early results were very promising, indicating that this method could decrease material dissolution time by a factor of 10 or more. However, the large and complicated lasers previously used are impractical for this application. Under the R^3 venture we aimed to benchmark the LDHP capabilities of turn-key commercial off-the-shelf (COTS) lasers, and to establish how this process could be integrated into an analytical workflow for nuclear forensic analysis. We demonstrated that geological rock standards could be quickly processed into fine powder by LDHP followed by complete acid digestion in 15 minutes, without elemental fractionation that would skew analytical results. We determined that the COTS laser can be used for LDHP that could potentially reduce dissolution time for solid nuclear debris samples in post detonation nuclear forensics. One downside to this approach, however, is that the laser interactions are different with every material, so extensive method validation would be required for all likely material compositions. The LDHP processing rates of several materials were tested and determined to be favorable in the beginning with significant slowdown due to particulate scattering. This could be mitigated either by stopping and centrifuging the sample at specific intervals, or through design of a continuous solvent flow through mechanism.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A comparative study of mechanical and chemical durability of non-wetting superhydrophobic and lubricant-infused surfaces

Fabrication of bioinspired non-wetting superhydrophobic surfaces (SHS) and lubricant-infused surfaces (LIS) has been studied extensively on a variety of materials. In contrast, durability of the surfaces exposed to harsh mechanical and chemical environments has been the subject of little attention. This study considers the mechanical and chemical durability of SHS and LIS copper surfaces fabricated via facile electrodeposition and chemical etching methods. The as-fabricated surfaces demonstrate excellent non-wetting characteristics with water contact angle of 160° and sliding angle below 5°. The surfaces are subject to mechanical wear through scratch test and water jet impingement at 15 psi and 20 psi as well as accelerated corrosion following the ASTM-E407 standard. The performance of the electrodeposited and etched non-wetting surfaces is systematically assessed in terms of contact and sliding angles and corrosion rate in a simulated marine environment. All surfaces are shown to be robust to mechanical wear after scratch test, with excellent stability of contact and sliding angles, and up to two orders of magnitude reduced corrosion rate compared to bare copper surface. SHS retained steadfast non-wetting characteristics under high-pressure water jet tests compared to the other surfaces while LIS, regardless of texturing method, showed one to two orders of magnitude reduced corrosion rate compared to bare copper surface throughout water jet impingement and chemical durability tests. The study presents for the first time a systematic comparison of durability of SHS and LIS through a common set of fabrication and testing protocol and helps identify appropriate non-wetting surfaces and fabrication methods based on the use environment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Enhanced Laplace Pressures for Functional Surfaces: Wicking, Switchability, and Selectivity

Abstract Wetting functionalities of rough surfaces are largely determined by the Laplace pressure generated across liquid–gas interfaces formed within surface structures. Typically, rough wetting surfaces create negative Laplace pressures, enabling capillary wicking, while rough non‐wetting surfaces create positive Laplace pressures, exhibiting fluid repellency. Here, with microfabricated reentrant structures, it is shown that the same surface can exhibit either a negative or positive Laplace pressure, regardless of its intrinsic wettability. This material‐independent Laplace pressure duality enables or enhances a range of wetting functionalities including wicking, switchability, and selectivity. On the same surface, capillary rise, capillary dip, and the combination of the two which leads to further enhancement of the total sustainable capillary height and Laplace pressure, the driving force for wicking is demonstrated. Further, active switching of wetting states between the hemiwicking and the repellent Cassie state on reentrant structures is shown. Moreover, with a water‐hexane mixture system, selective wetting of reentrant structures are demonstrated, that is, water can be selectively wicked or repelled in the presence of hexane, and vice versa. These functionalities are achieved, which would typically require complex chemical coatings, solely using surface structures, thus largely expanding the design space for a wide range of thermofluidic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Molecular Dynamics Investigation of Nanoscale Hydrophobicity of Polymer Surfaces: What Makes Water Wet?

The wettability of a polymer surface–related to its hydrophobicity or tendency to repel water–can be crucial for determining its utility, such as for a coating or a purification membrane. While wettability is commonly associated with the macroscopic measurement of a contact angle between surface, water, and air, the molecular physics that underlie these macroscopic observations are not fully known, and anticipating relative behavior of different polymers is challenging. To address this gap in molecular-level understanding, we use molecular dynamics simulations to investigate and contrast interactions of water with six chemically distinct polymers: polytetrafluoroethylene, polyethylene, polyvinyl chloride, poly(methyl methacrylate), Nylon 66, and polyvinyl alcohol. We show that several prospective quantitative metrics for hydrophobicity agree well with experimental contact angles. Moreover, the behavior of water in proximity to these polymer surfaces can be distinguished with analysis of interfacial water dynamics, extent of hydrogen bonding, and molecular orientation–even when macroscopic measures of hydrophobicity are similar. The predominant factor dictating wettability is found to be the extent of hydrogen bonding between polymer and water, but the precise manifestation of hydrogen bonding and its impact on surface-water structure varies. In the absence of hydrogen bonding, other molecular interactions and polymer mechanics control hydrophobic ordering. Furthermore, these results provide new insights into how polymer chemistry specifically impacts water-polymer interactions and translates to surface hydrophobicity. Such factors may facilitate the design or processing of polymer surfaces to achieve targeted wetting behavior, and presented analyses can be useful in studying the interfacial physics of other systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Toward controlling wetting hysteresis with nanostructured surfaces derived from block copolymer self-assembly

The synthesis of nanostructured surfaces via block copolymer (BCP) self-assembly enables a precise control of the surface feature shape within a range of dimensions of the order of tens of nanometers. Herein, this work studies how to exploit this ability to control the wetting hysteresis and liquid adhesion forces as the substrate undergoes chemical aging and changes in its intrinsic wettability. Via BCP self-assembly we fabricate nanostructured surfaces on silicon substrates with a hexagonal array of regular conical pillars having a fixed period (52 nm) and two different heights (60 and 200 nm), which results in substantially different lateral and top surface areas of the nanostructure. The wetting hysteresis of the fabricated surfaces is characterized using force–displacement measurements under quasistaic conditions and over sufficiently long periods of time for which the substrate chemistry and surface energy, characterized by the Young contact angle, varies significantly. The experimental results and theoretical analysis indicate that controlling the lateral and top area of the nanostructure not only controls the degree of wetting hysteresis but can also make the advancing and receding contact angles less susceptible to chemical aging. These results can help rationalize the design of nanostructured surfaces for different applications such as self-cleaning, enhanced heat transfer, and drag reduction in micro/nanofluidic devices.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

Multiscale water drop contact angles at selected silica surfaces

In this paper, multiscale advancing contact angles for glycerol/water drops at silica surfaces are reported for millidrops, submicron-drops, and nanodrops. Selected silica surfaces were muscovite, silicon, and talc. The contact angles for millidrops (1–2 mm) were determined by the traditional sessile drop technique. For submicron-drops (0.1–1.0 μm), a hollow tip Atomic Force Microscope (AFM) procedure was used. The contact angles for nanodrops (~7 nm) were examined from Molecular Dynamics (MD) simulation. The results were compared to evaluate the effect of drop size on the contact angle. In the case of the hydrophobic talc surface, the 75° advancing contact angle did not vary significantly with drop size. For the hydrophilic muscovite surface, the water drop wet the surface and an advancing contact angle of about 10° was found for the millidrops and submicron-drops. However, for the MD simulated nanodrops, attachment and spreading of the ~7 nm drop created a 2D film of molecular dimensions, the contact angle of which was difficult to define and varied from 0° to 17°. Perhaps of equal interest from the MD simulation results was that the spreading of the glycerol/water nanodrop at the muscovite surface resulted in crystallographic directional transport of water molecules to the extremities of the 2D film. Such separation and segregation left the center of the film with an increased concentration of glycerol. Based on these results, the line tension, which has been found in other investigations to account for contact angle decrease with a decrease in drop size, does not seem to be a significant factor in this study.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Wetting of a Hydrophobic Surface: Far-IR Action Spectroscopy and Dynamics of Microhydrated Naphthalene

The interaction of water and polycyclic aromatic hydrocarbons is of fundamental importance in areas as diverse as materials science and atmospheric and interstellar chemistry. The interplay between hydrogen bonding and dipole–π interactions results in subtle dynamics that are challenging to describe from first principles. Here, we employ far-IR action vibrational spectroscopy with the infrared free-electron laser FELIX to investigate naphthalene with one to three water molecules. We observe diffuse bands associated with intermolecular vibrational modes that serve as direct probes of the loose binding of water to the naphthalene surface. These signatures are poorly reproduced by static DFT or Møller–Plesset computations. Instead, a rationalization is achieved through Born–Oppenheimer Molecular Dynamics simulations, revealing the active mobility of water over the surface, even at low temperatures. Therefore, our work provides direct insights into the wetting interactions associated with shallow potential energy surfaces while simultaneously demonstrating a solid experimental–computational framework for their investigation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Role of underlying surface, rainstorm and antecedent wetness condition on flood responses in small and medium sized watersheds in the Yangtze River Delta region, China

Floods are becoming more frequent and are hard to control due to the shortage of water conservancy projects in small and medium sized basins, especially in developing regions. Understanding the hydrologic responses and estimated flood characteristics to storm events can help to predict flood disasters and form better effective mitigation and adaptation strategies. Here, using observations of several representative watersheds and Artificial Neural Networks (ANN) and Principal Component Regression (PCR) models, we conducted data-driven analyses to examine the flood responding characteristics. We quantified the relative contributions of the influencing factors to the variation of each flood characteristic. Statistical analysis of the observations shows that the drainage area plays a key role in determining the distribution of lag time and peak discharge. Rainstorm variability has direct influence on floods, and typhoon-induced rainstorms with high total rainfall and rainfall intensity generate higher lag time, flood peak, unit discharge and runoff depth, but lower runoff coefficient. The ANN and PCR models accurately predicted the variations of flood features using the driving factors including physical geographical characteristics, rainstorm features, and antecedent condition. Physical geographic characteristics are key influential factors of lag time, flood peak and runoff coefficient, while the rainstorm features control the magnitude of unit discharge and runoff depth. These results indicate that floods are mainly affected by rainstorm features and physical geographic characteristics in the Yangtze River delta, and it might become more damaging with the increasing rainfall extremes and sprawling impervious surfaces in a changing environment.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Engineering surface segregation of perovskite oxide through wet exsolution for CO catalytic oxidation

Cation segregation occurring near the surface or interfaces of solid catalysts plays an important role in catalytic reactions. Unfortunately, the native surface of perovskite oxides is dominated by passivated A-site segregation, which severely hampers the catalytic activity and durability of the system. To address this issue, we present a wet exsolution method to reconstruct surface segregation in perovskite cobalt oxide. Here, under reduction etching treatment of glycol solution, inert surface Sr segregation was transformed into active Co 3 O 4 segregation. By varying the reaction time, we achieved differing coverage of the active Co 3 O 4 segregation on the La 0.5 Sr 0.5 CoO 3-δ (LSCO) perovskite oxide surface. This study reveals that CO oxidation activity exhibits a volcano-shaped dependence on the coverage of Co 3 O 4 segregation at the surface of a perovskite cobalt oxide. Furthermore, we find that a suitable coverage of Co 3 O 4 segregation can dramatically improve the catalytic activity of the perovskite catalyst by enhancing interface interactions. Co K-edge, Co L-edge, and O K-edge X-ray absorption spectra confirm that the synergistic effect optimizes the covalence of the metal-oxygen bond at the surface and interface. This work not only contributes to the design of perovskite-type catalysts, but also provides important insight into the relationship between surface segregation and catalytic activity.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Alternative All-Metal Scroll Pump Design

In tritium process systems, vacuum pumps are typically used to evacuate volumes and piping, as well as transfer gas to other parts of the process. This was done using the combination of an all-metal scroll pump with a metal bellows backing pump. The all-metal scroll pump, manufactured by Normetex, has been unavailable since 2012, and efforts continue to find a suitable replacement. The main obstacle is finding a pump that has no oils or polymer components, which degrade when exposed to tritium and introduce corrosive and/or hazardous impurities into the process. There have been development efforts to design an all-metal scroll pump design alternative to the Normetex style. The first generation was fabricated out of machined stainless steel, but the thermal management and increased weight were not ideal. To mitigate the weight, an aluminum version was designed. The tritium holdup on untreated aluminum surfaces can be greater than stainless steel, so the wetted aluminum surfaces were electroless plated in nickel and then electroplated in gold. The development effort outlined in this report details the design of an improved version of the stainless steel version.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Enhanced superconducting qubit performance through ammonium fluoride etch

The performance of superconducting qubits is often limited by dissipation and two-level systems (TLS) losses. The dominant sources of these losses are believed to originate from amorphous materials and defects at interfaces and surfaces, likely as a result of fabrication processes or ambient exposure. Here, we explore a novel wet chemical surface treatment at the Josephson junction-substrate and the substrate-air interfaces by replacing a buffered oxide etch (BOE) cleaning process with one that uses hydrofluoric acid followed by aqueous ammonium fluoride. We show that the ammonium fluoride etch process results in a statistically significant improvement in median $\text{T}_1$ by $\sim22\%$ (p = 0.002), and a reduction in the number of strongly-coupled TLS in the tunable frequency range. Microwave resonator measurements on samples treated with the ammonium fluoride etch after niobium deposition and etching also show $\sim33\%$ lower TLS-induced loss tangent compared to the BOE treated samples. As the chemical treatment primarily modifies the Josephson junction-substrate interface and substrate-air interface, we perform targeted chemical and structural characterizations to examine materials differences at these interfaces and identify multiple microscopic changes that could contribute to decreased TLS losses.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Observational Evidence of State‐Dependent Positive and Negative Land Surface Feedback on Afternoon Deep Convection Over the Southern Great Plains

Abstract The detection of soil moisture‐precipitation feedback is complicated by the dependence of feedback sign on atmospheric state and cloud types. We evaluated responses of convective clouds to changes in surface evaporative fraction (EF) from satellite and ground‐based measurements over the Southern Great Plains in summer months. Strong responses to EF were inferred only after accounting for tropospheric states supporting systematically positive or negative responses. State dependence (inferred from controlled model experiments) explains the weak response found in previous studies. The probability of transitions from shallow to deep cumulus, and subsequent precipitation onset, increases by 58% over drier surfaces in weakly stratified environments having deeper boundary layers. Boundary layer dynamics play a more important role than low‐level relative humidity in these environments. Wetter surfaces yield increased deep convection in moist and thermally stratified environments. The distinct pathways of convective initiation over dry and wet land surfaces can play important roles in drought onset and termination.

Qiu, Shaoyue↗
DOE OSTI2025

Compatibility of molten plutonium with wrought and additively manufactured metal crucibles

Understanding plutonium’s interaction with metals is crucial for optimizing pyrochemical operations, nuclear fuel containment, and various actinide processing techniques. Traditionally, tantalum crucibles are employed for plutonium processing due to their high durability, excellent temperature stability, and low solubility in plutonium. However, tantalum faces challenges such as plutonium wetting and diffusion, making surface coatings particularly important for crucibles in pyrochemical applications to enhance corrosion resistance against plutonium. Tantalum is also expensive and difficult to machine, prompting the need for advanced manufacturing techniques to address these challenges. Here, in this work, we investigate the interaction of Pu with tantalum and titanium crucibles fabricated using both traditional machining methods and laser powder bed fusion (LPBF) additive manufacturing (AM). LPBF-AM is an advanced technique that allows for the creation of complex geometries from traditionally difficult-to-machine metals by using a high-powered laser to build parts. Previous studies of conventional manufactured tantalum have utilized oxidation and carburization of the surface to mitigate plutonium wetting; however, no studies of surface modified LPBF-AM material have been undertaken. These studies are crucial, given the typical differences in the grain structure between conventional and LPBF-AM materials. All crucibles underwent differential scanning calorimetry to confirm the melting of plutonium. Subsequently, the crucibles were sectioned and mounted in epoxy for microstructural analysis using optical microscopy and scanning electron microscopy. This investigation, comparing the performance of wrought vs AM metal crucibles, provides a basis for future tooling applications in actinide processing techniques and can address the challenges associated with traditional machining, particularly in pyrochemical applications.

Actinides↗
DOE OSTI2020

Tailored PEDOT:PSS hole transport layer for higher performance in perovskite solar cells: Enhancement of electrical and optical properties with improved morphology

Precise control over the charge carrier dynamics throughout the device can result in outstanding performance of perovskite solar cells (PSCs). Poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) is the most actively studied hole transport material in p-i-n structured PSCs. However, charge transport in the PEDOT:PSS is limited and inefficient because of its low conductivity with the presence of the weak ionic conductor PSS. In addition, morphology of the underlying PEDOT:PSS layer in PSCs plays a crucial role in determining the optoelectronic quality of the active perovskite absorber layer. This work is focused on realization of a non-wetting conductive surface of hole transport layer suitable for the growth of larger perovskite crystalline domains. This is accomplished by employing a facile solvent-engineered (ethylene glycol and methanol) approach resulting in removal of the predominant PSS in PEDOT:PSS. The consequence of acquiring larger perovskite crystalline domains was observed in the charge carrier dynamics studies, with the achievement of higher charge carrier lifetime, lower charge transport time and lower transfer impedance in the solvent-engineered PEDOT:PSS-based PSCs. Use of this solvent-engineered treatment for the fabrication of MAPbI3 PSCs greatly increased the device stability witnessing a power conversion efficiency of 18.18%, which corresponds to ~37% improvement compared to the untreated PEDOT:PSS based devices.

14 SOLAR ENERGY↗