Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “structured liquid”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Acoustic Emission Monitoring of the DC-XA Composite Liquid Hydrogen Tank During Structural Testing

The results of acoustic emission (AE) monitoring of the DC-XA composite liquid hydrogen tank are presented in this report. The tank was subjected to pressurization, tensile, and compressive loads at ambient temperatures and also while full of liquid nitrogen. The tank was also pressurized with liquid hydrogen. AE was used to monitor the tank for signs of structural defects developing during the test.

Wilkerson, C.↗
NASA NTRS1974

Strain-cycling fatigue behavior of ten structural metals tested in liquid helium (4 K), in liquid nitrogen (78 K), and in ambient air (300 K)

Strain-cycling fatigue behavior of 10 different structural alloys and metals was investigated in liquid helium (4 K), in liquid nitrogen (78 K), and in ambient air (300 K). At high cyclic lives, fatigue resistance increased with decreasing temperature for all the materials investigated. At low cyclic lives, fatigue resistance generally decreased with decreasing temperature for the materials investigated. Only for Inconel 718 did fatigue resistance increase with decreasing temperature over the entire life range investigated. Comparison of the experimental fatigue behavior with that predicted by the Manson method of universal slopes showed that the fatigue behavior of these materials can be predicted for cryogenic temperatures by using material tensile properties obtained at those same temperatures.

Nachtigall, A. J.↗
NASA NTRS1987

Liquid phase epitaxy growth of GaAs/GaAlAs multi-quantum well structures

Experiments in liquid phase epitaxial fabrication of thin GaAs/GaAlAs layers over a planar substrates have been carried out. Layer thicknesses smaller than 300 A were routinely obtained, with the best result being 120 A. Interface sharpness between the layers is approximately 10 A, which is comparable to OMCVD results, but the layers' thicknesses are usually not uniform. Of the experimental parameters, the growth time and the cooling rate seem to have the largest effect on the obtained layer thickness, while the growth temperature and the substrate crystallographic orientation produce less noticeable effects. Quantum effects in the grown layers were observed by photoluminescence measurements.

Cser, J.↗
NASA NTRS1999

The Three-D Flow Structures of Gas and Liquid Generated by a Spreading Flame Over Liquid Fuel

We developed a new experimental technique called: Combined laser sheet particle tracking (LSPT) and laser holographic interferometry (HI), which is capable of measuring the transient behavior of three dimensional structures of temperature and flow both in liquid and gas phases. We applied this technique to a pulsating flame spread over n-butanol. We found a twin vortex flow both on the liquid surface and deep in the liquid a few mm below the surface and a twin vortex flow in the gas phase. The first twin vortex flow at the liquid surface was observed previously by NASA Lewis researchers, while the last two observations are new. These observations revealed that the convective flow structure ahead of the flame leading edge is three dimensional in nature and the pulsating spread is controlled by the convective flow of both liquid and gas.

Tashtoush, G.↗
NASA NTRS1983

Effect of Liquid Droplets on Turbulence Structure in a Round Gaseous Jet

A second-order model which predicts the modulation of turbulence in jets laden with uniform size solid particles or liquid droplets is discussed. The approach followed is to start from the separate momentum and continuity equations of each phase and derive two new conservation equations. The first is for the carrier fluid's kinetic energy of turbulence and the second for the dissipation rate of that energy. Closure of the set of transport equations is achieved by modeling the turbulence correlations up to a third order. The coefficients (or constants) appearing in the modeled equations are then evaluated by comparing the predictions with LDA-measurements obtained recently in a turbulent jet laden with 200 microns solid particles. This set of constants is then used to predict the same jet flow but laden with 50 microns solid particles. The agreement with the measurement in this case is very good.

Elghobashi, S. E.↗
NASA NTRS1984

Effect of liquid droplets on turbulence structure in a round gaseous jet

A proposed two equation turbulence model for incompressible dilute two phase flows was validated and extended for steady incompressible two phase flow including phase change. The model was tested for the flow of a turbulent axisymmetric gaseous jet laden with multisize evaporating liquid droplets. Predicted results include distributions of the mean velocity; volume fractions of different phases concentration of the evaporated material in the carrier phase; turbulence intensity and shear stress of the carrier phase; droplet diameter distribution; and the jet spreading rate. Results are analyzed based on a qualitative comparison with the corresponding single phase jet flow.

Mostafa, A. M.↗
NASA NTRS2002

Studies of Nucleation and Growth, Specific Heat and Viscosity of Undercooled Melts of Quasicrystals and Polytetrahedral-Phase-Forming Alloys

The local atomic structures of undercooled liquid metals are presumed to be icosahedral; this order is incompatible with translational periodicity, constituting a barrier to the nucleation of the crystal phase. The extended atomic structure of the icosahedral quasicrystal (i-phase) is similar to that presumed in the undercooled liquid. Therefore, a comparison of the maximum undercooling in alloys that form the i-phase with those that form crystal phases provides a probe of the liquid structure.

Kelton, K. F.↗
NASA NTRS2017

Characterization of the Modal Characteristics of Structures Operating in Dense Liquid Oxygen Turbopumps

A number of valuable conclusions can be drawn from this study. First, knockdown factors for a specific fluid are not constant but instead are dependent on the mode shape, although the largest this variability gets is about 10% for LOX, the densest fluid. The factors decrease the most for lower frequency shapes and less for higher ones. It follows, therefore, that mode number mismatch between air and fluid operation becomes not only possible, but common, as a knockdown factor for a particular mode shape may be higher than for another mode shape. Since this is a function of added mass, the mismatch is more prevalent for higher density fluids, but it initiates even for very low density ones. Another important conclusion reached is that it appears that the basic mode shapes of a structure do not change if it is fully symmetric, which includes its geometry and boundary conditions. There is some indication of small changes in the relative magnitudes within the mode shape. This conclusion is evident in the results from the cantilever rectangular plate and the inducer, which are not symmetric, and the fixed-fixed plate and the annular disk, which are. For non-symmetric structures, though, the mode shapes almost universally change for dense fluids, as shown by the very low MAC calculations. For the inducer in particular, the changes follow a trend of reduced parabolic and sine wavelengths with increasing density. It is critical to recognize the change in mode shape for several reasons. First, model updating with modal test becomes problematic if the shapes change. Second, design to avoid resonance is highly critical on the mode shape for modes other than the primary ones, as resonance is only a factor when the excitation shape matches the mode shape. Finally, application of the modal superposition method of forced response analysis is dependent on the use of accurate mode shapes. A more-refined assessment of the "knockdown" factor values and ranges than any previously reported in the literature for a realistic engineering structure is also presented in this paper. This data is of tremendous benefit for preliminary analysis and design, where a quick estimate is necessary. These results are important not just for rocket engine turbomachinery, but for water pumps and turbines, propellers, and any other structure operating in a heavy fluid with dynamic excitation. The clear avenue for future work for this endeavor is to expand the analytical techniques discussed in the literature to develop analytical expressions and justification for the mode shape changes and associated frequency knockdowns. These expressions must be able to accurately predict the functional relationship to the shapes, which will enable accurate tracing of the mode number from vacuum analysis (or testing in air) to analysis and operation in the intended fluid environment.

Chiu, Joseph↗
NASA NTRS1972

Application of Rochrome liquid crystal tapes for thermographic testing of bonded structures

The use of ROCHROME liquid crystal tape for thermographic testing of bonded structures for aircraft is described. The techniques for applying the tape, heating the test panels, and photographing the resulting thermal patterns are described and discussed. The results obtained are compared with those reported previously for the same test panels coated directly with liquid crystals applied by spraying. Other panels previously examined by various nondestructive techniques, both by thermography, were also tested. Results for these latter panels are presented and discussed. For both sets of panels good correlation with previous work was obtained. Deficiencies associated with present ROCHROME tape are described. In general, these stem from the lack of optimization for materials testing of the ROCHROME tape, particularly with respect to the adhesive system and supporting film.

Source record↗
NASA NTRS2006

Review of Current State of the Art and Key Design Issues With Potential Solutions for Liquid Hydrogen Cryogenic Storage Tank Structures for Aircraft Applications

Due to its high specific energy content, liquid hydrogen (LH2) is emerging as an alternative fuel for future aircraft. As a result, there is a need for hydrogen tank storage systems, for these aircraft applications, that are expected to provide sufficient capacity for flight durations ranging from a few minutes to several days. It is understood that the development of a large, lightweight, reusable cryogenic liquid storage tank is crucial to meet the goals of and supply power to hydrogen-fueled aircraft, especially for long flight durations. This report provides an annotated review (including the results of an extensive literature review) of the current state of the art of cryogenic tank materials, structural designs, and insulation systems along with the identification of key challenges with the intent of developing a lightweight and long-term storage system for LH2. The broad classes of insulation systems reviewed include foams (including advanced aerogels) and multilayer insulation (MLI) systems with vacuum. The MLI systems show promise for long-term applications. Structural configurations evaluated include single- and double-wall constructions, including sandwich construction. Potential wall material candidates are monolithic metals as well as polymer matrix composites and discontinuously reinforced metal matrix composites. For short-duration flight applications, simple tank designs may suffice. Alternatively, for longer duration flight applications, a double-wall construction with a vacuum-based insulation system appears to be the most optimum design. The current trends in liner material development are reviewed in the case that a liner is required to minimize or eliminate the loss of hydrogen fuel through permeation.

Mital, Subodh K.↗
NASA NTRS1991

A surface-based cloud observing system

The paper describes a surface-based system, called the Cloud Observing System (COS), that was developed for measurements of the dynamical and thermodynamical properties of clouds and of their interaction with the large-scale environment, by combining several remote sensors and in situ systems. The atmospheric parameters that will be measured by COS include precipitation, the velocity and direction of wind, the cloud liquid water, the low-level winds and turbulence structure, integrated liquid and vapor quantities, the temperature and water profiles, the cloud radiance and the cloud base temperature, irradiances at the surface, the low-level temperature profile, the cloud-base height, and the cloud fraction; video cameras will provide visual records of clouds.

Albrecht, B. A.↗