Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “stereolithography”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Experimental characterization of a triply periodic minimal surface PCM-to-air thermal energy storage device

Here, the expansion of energy production has intensified research into thermal energy storage (TES) to manage variability and improve system efficiency. Heat exchanger design is critical to achieving high power densities in TES systems. This study presents a high-surface-area phase change material (PCM)-to-air heat exchanger fabricated via resin-based stereolithography with a novel gyroid-based geometry tailored for enhanced performance. Material properties of the commercial PCM and resin were characterized using analytical techniques. A controlled air loop was used to evaluate heat transfer and pressure drop at various flow rates and inlet temperatures. Results show a strong dependence on the inlet temperature difference (ΔT) relative to the PCM melting point. During charging at the highest flow rate, increasing the inlet air temperature from ΔT = 5 °C to 20 °C above the melting point increased the average heat transfer rate by 187%. During discharging, decreasing the inlet temperature by the same ΔT below the melting point led to a 232% increase. Notably, the high-surface-area design enabled nearly symmetric charging and discharging behavior, a novel result for PCM-based TES systems which are often restricted by natural convection and other effects. The overall heat transfer coefficient was calculated and compared to values from standard design correlations. The maximum thermal effectiveness reached 95% at ΔT = 20 °C and a moderate flow rate of 34 m 3 /h. Peak coefficients of performance (COP) of 7 during charging and 6.4 during discharging were observed at ΔT = 20 °C and a low flow rate of 20 m 3 /h. These results demonstrate the viability of additively manufactured geometries for advanced TES applications.

25 ENERGY STORAGE↗
DOE OSTI2025

Scalable phononic metamaterials: Tunable bandgap design and multi-scale experimental validation

Phononic metamaterials offer unprecedented control over wave propagation, making them essential for applications such as vibration isolation, waveguiding, and acoustic filtering. However, achieving scalable and precisely tunable bandgap properties across different length scales remains challenging. This study presents a user-friendly design framework for phononic metamaterials, enabling ultra-wide bandgap tunability (B/ω c ratios up to 172 %) across multiple frequency ranges and scales. Using finite element simulations of a Yablonovite-inspired unit cell, we establish a comprehensive parametric design space that illustrates how geometric parameters, such as sphere size and beam diameter, controls bandgap width and frequency. The scalability and robustness of the framework are validated through experimental testing on additively manufactured structures at both macro (10 mm) and micro (80 µm) scales, fabricated using Stereolithography and Two-Photon Polymerization. Transmission loss measurements, conducted with piezoelectric transducers and laser vibrometry, closely match simulations in the kHz and MHz frequency ranges, confirming the reliability and consistency of the bandgap behavior across scales. This work bridges theory and experiments at multiple scales, offering a practical methodology for the rapid design of phononic metamaterials and expanding their potential for diverse applications across a broad range of frequencies.

36 MATERIALS SCIENCE↗
DOE OSTI2020

3D-Printed Membranes with a Zwitterionic Hydrogel Coating for More Robust Oil–Water Separation

Three-dimensional (3D)-printed membranes via stereolithography (SLA) are promising in oil–water separation, which is the key in the purification of industrial oily wastewater. To achieve gravity-driven oil–water separation, the membrane material needs to be simultaneously hydrophilic/oleophobic. However, most of the state-of-the-art materials for SLA do not meet the requirement. While water-adsorbing hydrogel is simultaneously hydrophilic/oleophobic and there have been reports on 3D printing of hydrogels in biomedical applications, the hydrogel is too soft for membrane application. Here, we report a simple approach to tackle the issue: a hydrogel coating on SLA-based plastic membranes. The coating is fabricated, using [2-(methacryloyloxy) ethyl] dimethyl-(3-sulfopropyl) ammonium hydroxide as the zwitterionic monomer and acrylamide as the comonomer, via in situ polymerization on SLA-based plastic membranes. The contact angle tests and Fourier transform infrared spectrum show that such a membrane readily adsorbs water and becomes simultaneously hydrophilic/oleophobic. The oil–water separation tests indicate that the water-adsorbed membrane is highly efficient in gravity-driven oil–water separation in 31 repeating cycles. Our results indicate the great potential of 3D-printed membranes in oil–water separation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Photoinitiated Olefin Metathesis and Stereolithographic Printing of Polydicyclopentadiene

Recent progress in photoinitiated ring-opening metathesis polymerization (photoROMP) has enabled the lithographic production of patterned films from olefinic resins. Recently, we reported the use of a latent ruthenium catalyst (HeatMet) in combination with a photosensitizer (2-isopropylthioxanthone) to rapidly photopolymerize dicyclopentadiene (DCPD) formulations upon irradiation with UV light. While this prior work was limited in terms of catalyst and photosensitizer scope, a variety of alternative catalysts and photosensitizers are commercially available that could allow for tuning of thermomechanical properties, potlifes, activation rates, and irradiation wavelengths. Herein, 14 catalysts and 8 photosensitizers are surveyed for the photoROMP of DCPD and the structure–activity relationships of the catalysts examined. Properties relevant to stereolithography additive manufacturing (SLA AM)-potlife, irradiation dose required to gel, conversion-are characterized to develop catalyst and photosensitizer libraries to inform development of SLA AM resin systems. Two optimized catalyst/photosensitizer systems are demonstrated in the rapid SLA printing of complex, multidimensional pDCPD structures with microscale features under ambient conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

3D Printed Nanoporous Separators Based on Polymerization-Induced Phase Separation for Fast-Charging, High Cycling Stability Li-Ion Batteries

Fast charging and stable lithium-ion batteries (LIBs) require prompt Li ion transport between electrodes. 3D porous separators can potentially improve ion transport at both the microscale and macroscale levels. Additive manufacturing (AM) is an ideal tool to produce and study 3D porous separators of LIBs, although little work has been reported in this area. Here, we demonstrate porous structural control in layer-by-layer printed hexanediol diacrylate (HDDA) separators using a projection micro stereolithography (PμSL) AM technology and present their corresponding battery performance in lithium nickel manganese cobalt oxide (NMC)/graphite full cells. The composition of photocurable resin determines the porous morphology (e.g., bicontinuous and droplet-like), while the settings of printing layer thickness and number of exposures can be used to adjust the porosity (e.g., from 27% to 63%). Optimal resin and print conditions are determined, and the resulting separator exhibits superior Li ion conductivity and therefore higher rate performance and longer cycling life. Compared with a Celgard 2325 separator, the optimized porous HDDA separator increases the 10C-rate capacity by 34% and decreases the capacity degradation rate at the 1C-rate by 4.9%. In conclusion, this work paves the way for future AM of 3D separators for high-energy, high-power, and long-cycling-life LIBs.

25 ENERGY STORAGE↗
DOE OSTI2024

Viability of Additively Manufactured Electrodes for Lithium-Ion Batteries

As the global economy becomes increasingly electrified, the demand for batteries and energy storage is expected to rise significantly, particularly in the transportation and electricity sectors. Lithium-ion batteries (LIBs) are currently the most advanced and widely used technology in this field. Traditionally, LIBs are manufactured using simple 2D planar geometries to maximize production efficiency and minimize costs. However, this approach limits energy density due to the restricted design flexibility of the electrodes. Additive manufacturing (AM) offers a promising solution to enhance the energy density and efficiency of LIBs by enabling the design of architectures that reduce diffusive losses and allow for a greater amount of active material to be incorporated within the same device footprint, thereby minimizing the use of inactive materials. Different AM techniques come with their own set of limitations, including printing speed, material compatibility, and scale, which must be considered when designing electrodes. Scalable and cost-effective methods are particularly important for electric vehicle batteries, while achieving higher energy densities in microbatteries is crucial for the miniaturization of wearable electronics and medical devices. Here, in this study, we simulate various 3D porous electrode designs for LIBs using graphite and nickel manganese cobalt oxide (NMC) electrodes. These designs are selected to represent structures that could be produced using different AM techniques, such as direct ink writing, fused deposition modeling, and stereolithography. Our results indicate that at higher charging rates and increased areal mass loading, 3D structures can outperform traditional 2D electrodes, although the benefits may diminish with more complex designs that are harder to manufacture. The observed gains in energy density are attributed to improved electrode utilization and reduced diffusive energy losses. This comprehensive analysis of structure–performance relationships will provide valuable insights to guide future research on 3D designs, material selection, and AM techniques for additively manufactured battery electrodes.

25 ENERGY STORAGE↗
DOE OSTI2020

Cryogenic goniometer for measurements in pulsed magnetic fields fabricated via additive manufacturing technique

Complex high-precision mechanical devices can be fabricated using 3-dimensional printing technology with the help of computer-aided design. Using 3D stereolithography, we have constructed a cryogenic goniometer for measurements in pulsed magnetic fields of up to 100 T, at temperatures as low as 0.5 K. We review the properties of several materials tested in developing the goniometer and report on its design and performance. The goniometer allows samples to be rotated in situ to a precision of 0.2 deg, so that the field can be applied at many different angles to the samples’ symmetry directions. Following its success, we establish that 3D printing is now a viable technology for pulsed-field and other cryogenic probes.

3D printing↗
DOE OSTI2020

Experimental Investigation of Sweeping Jet Film Cooling in a Transonic Turbine Cascade

Abstract The sweeping jet (SJ) film cooling hole has shown promising cooling performance compared to the standard shaped hole in low-speed conditions. The present work demonstrates the first attempt of SJ film cooling at an engine relevant Mach number. An experimental investigation was conducted to study the SJ film cooling on a nozzle guide vane suction surface. A well-established additive manufacturing technique commonly known as stereolithography (SLA) was utilized to design a transonic, engine representative vane geometry in which a row of SJ holes was used on the vane suction surface. Experiments were performed in a linear transonic cascade at an exit Mach number of 0.8 and blowing ratios of BR = 0.25–2.23. The measurement of heat transfer was conducted with the transient IR method, and the convective heat transfer coefficient (HTC) and adiabatic film cooling effectiveness were estimated using a dual linear regression technique (DLRT). Aerodynamic loss measurements were also performed with a total pressure Kiel probe at 0.25Cax downstream of the exit plane of the vane cascade. Experiments were also conducted for a baseline-shaped hole (777-hole) for a direct comparison. Results showed that the SJ hole has a wider coolant spreading in the lateral direction near the hole exit due to its sweeping motion that improves the overall cooling performance particularly at high blowing ratios (BR > 1). Aerodynamic loss measurement suggested that the SJ hole has a comparable total pressure loss to the 777-shaped hole.

Engineering↗
DOE OSTI2023

Biomimetic tissue phantoms for neurosurgical near-infrared fluorescence imaging

Neurosurgical fluorescence imaging is a well-established clinical approach with a growing range of indications for use. However, this technology lacks effective phantom-based tools for development, performance testing, and clinician training. Our primary aim was to develop and evaluate 3D-printed phantoms capable of optically and morphologically simulating neurovasculature under fluorescence angiography. Volumetric digital maps of the circle of Willis with basilar and posterior communicator artery aneurysms, along with surrounding cerebral tissue, were generated. Phantoms were fabricated with a stereolithography printer using custom photopolymer composites, then visualized under white light and near-infrared fluorescence imaging. Feature sizes of printed components were found to be within 13% of digital models. Phantoms exhibited realistic optical properties and convincingly recapitulated fluorescence angiography scenes. Methods identified in this study can facilitate the development of realistic phantoms as powerful new tools for fluorescence imaging.

3D modeling↗
DOE OSTI2025

Rheological Properties of Enzymatically Hydrolyzed Corn Stover Pretreated via Deacetylation and Mechanical Refining

Lignocellulosic biomass is a feedstock for fuels and chemicals that does not compete with food resources and has less contaminants than refuse-derived biomass feedstocks. To convert lignocellulosics to biofuels or value-added products, multiple processing steps are typically necessary. One method of producing biofuels from lignocellulosic biomass utilizes a deacetylation and mechanical refining pretreatment and an enzymatic hydrolysis reaction to produce fermentable sugars from cellulose and hemicellulose. The rheological properties of biomass, such as yield stress and plastic viscosity, change during enzymatic hydrolysis and alter the energy requirements for pumping and mixing, an important consideration for the design of processing equipment. The dynamic changes in rheological properties that occur in a corn stover feedstock undergoing enzymatic hydrolysis are characterized in this work, and the influence on pressure losses in piping systems is estimated. Two rheometer geometries were fabricated with stereolithography 3D printing to reduce wall slip and sample ejection. The slurries have complex rheological behaviors that include shear-thinning behavior. Shear stress ramps were performed on samples at 20 and 50 degrees C using the custom geometries, and the Herschel-Bulkley model was fit to the data. The dynamic nature of the rheological properties is correlated with changes in the average fiber length at various extents of reaction, and the influence of solids concentration on the observed rheology and piping pressure losses is discussed.

09 BIOMASS FUELS↗
DOE OSTI2023

A review of materials used in tomographic volumetric additive manufacturing

Abstract Volumetric additive manufacturing is a novel fabrication method allowing rapid, freeform, layer-less 3D printing. Analogous to computer tomography (CT), the method projects dynamic light patterns into a rotating vat of photosensitive resin. These light patterns build up a three-dimensional energy dose within the photosensitive resin, solidifying the volume of the desired object within seconds. Departing from established sequential fabrication methods like stereolithography or digital light printing, volumetric additive manufacturing offers new opportunities for the materials that can be used for printing. These include viscous acrylates and elastomers, epoxies (and orthogonal epoxy-acrylate formulations with spatially controlled stiffness) formulations, tunable stiffness thiol-enes and shape memory foams, polymer derived ceramics, silica-nanocomposite based glass, and gelatin-based hydrogels for cell-laden biofabrication. Here we review these materials, highlight the challenges to adapt them to volumetric additive manufacturing, and discuss the perspectives they present. Graphical abstract

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermomechanical properties of stereolithographic 3D-printed zinc oxide nanocomposites

Stereolithography (SLA) is a highly versatile additive manufacturing technique that utilizes various ink formulations to fabricate 3D-printed nanocomposite structures with desired properties. Zinc oxide (ZnO) is a promising candidate due to its excellent mechanical and thermal stability, and compatibility with various polymeric matrices. Here, in this work, varying ink formulations containing ZnO nanoparticles, along with employing appropriate post-printing curing parameters to fabricate SLA 3D-printed acrylate-based nanocomposites with improved mechanical and thermal properties, were reported. This study can significantly contribute to expanding its potential use in practical applications such as biomedical and structural applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Metamaterials for Mechanically Directing Cell Phenotype

Recently, abundant research has begun to reveal how microscale surface topography can influence a wide range of cell phenotypes in vitro, such as cell mobility, cell size and cell viability (Flemming et al. 1999, Nikkhah et al. 2012, Wang et al. 2016). However, while these studies shed some light on cell interactions with 2D surfaces of different length scales, cells in vivo experience their surroundings in 3D. Therefore, investigations into cell interactions with varying 3D microstructures are needed to gain biologically relevant insight into how microarchitecture and feature size influences cell behavior. Understanding this relationship between 3D microstructure and cell behavior will have a huge impact on tissue engineering and mechanobiology. Until now, the ability to fabricate complex 3D microstructures for cell behavior studies has been limited. This study harnessed LLNL’s Projection Micro-Stereolithography (PμSL) capability to probe the effects of micron-scale changes in 3D architecture on cell phenotype. Furthermore, our studies explored the application of external forces—such as cyclic loading and flow-induced shear stress—to cell-seeded 3D microstructures to further examine cell behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Swab Testing Results Summary

Swabs Tested: 1. FAST Spiral NP Swab, designed and supplied by Abiogenix, printed from polyamide 11 (Nylon) using HP Multi Jet Fusion printers. 2. NP Swab designed by USF Health and Northwell Health in collaboration with Formlabs. Printed at LLNL using the Form 3B stereolithography printer in Formlabs Surgical Guide resin.

42 ENGINEERING↗
DOE OSTI2025

Experimental Characterization of High-Surface Area Thermal Energy Storage

There is growing interest in energy storage technologies due to the expansion of renewable energy sources that are inherently intermittent and the increasing frequency of extreme weather events that disturb the power grid. Power consumption in buildings makes up approximately 76% of all electricity usage on the grid and is primarily used for thermal applications such as space conditioning, hot water, and cooking. This makes thermal energy storage (TES) an ideal solution for many of these applications. Many TES technologies rely on latent energy storage, which utilizes the melting/solidification of phase change materials (PCM) to store energy. Typically, TES designs suffer from low power density due to their low inherent thermal conductivity. This limitation makes the deployment of TES in active applications difficult as the ease of access to energy is essential for effective use. Common routes for improving power density include high thermal conductivity additives or extended features such as fins that increase cost. This study presents an alternative approach to improving performance through increasing the overall surface area to volume ratio of the device, to increase the available area for convection to occur between the working fluid and PCM. In the study a commercial PCM was selected with a transition temperature ideal for space heating applications. The heat exchanger design utilizes a unique application of triply periodic minimal surfaces (TPMS) for macro-encapsulation of the PCM. The use of TPMS for heat exchangers has been growing in interest due to their high-surface area to volume ratios, which were previously unmanufacturable until the development of additive manufacturing. A modular system was designed and manufactured with a stereolithography resin printing system that is then backfilled with PCM. An experiment test set-up is designed to test the charge and discharge performance of the thermal storage using a conditioned air stream. The pressure drop of the design is tested across a variety of flow rates. When compared to existing experimental data within literature, there is excellent agreement based on the Reynolds number at similar hydraulic diameters. Several inlet temperatures are tested at consistent temperature differences from the phase change temperature for both charging and discharging. Additionally, the volumetric flow rate is varied for each temperature set point. It was found that increasing flow rate had diminishing returns in reducing the overall charge time of the TES. The temperature delta from the melting temperature was the primary contributor to the change in average heat flux with limited variation in average heat transfer rate between charging and discharging at similar inlet temperatures and flow rates. The TPMS heat exchanger design has a high air-side pressure drop but it provides high heat transfer rates. This helps maintain a high outlet temperature during discharge, which is important to thermal comfort applications. The design, manufacturing, and experimental characterization of the TES device will be presented as part of this study.

25 ENERGY STORAGE↗
DOE OSTI2026

Development of large-scale, 3D Printed high temperature ceramic material

Through this collaborative effort, a new 3D printing platform for ceramics called laser-induced slip casting (LIS) was explored and developed for improving the processing and manufacture of silicon carbide (SiC), a high temperature ceramic material. This method prints layers of ceramic slips/slurries with subsequent selective-laser heating to dry each layer to build a 3D structure. The completed and dried part is then sintered. This manufacturing process is inherently lower cost than alternative ceramic printing methods such as binder jet technology or stereolithography when it comes to the feedstock material but is more expensive than robocasting or direct ink writing. However, it has the potential to make more controlled parts with less defects compared to robocasting. The largest cost is the heating source for the printer. With this technique, there is potential to make large ceramic parts in a near-net shape. Further, there is no known commercial manufacturing of 3D printed ceramics that creates a large range of different high-density ceramics at large scale. The goals and outcomes for the development of the new printing technology were: 1) assessing the technology with alumina by characterizing coupons, 2) printing and sintering of silicon carbide (SiC), and 3) characterization and properties testing of materials printed and a scale-up of SiC part(s). Through this collaborative project, it was sought to provide the best solution to achieving highly dense and near-net shaped ceramic parts at large scale and reduced cost. The goal was to produce high density sintered materials for applications in defense, energy generating systems, armor, and wear parts using 3D printing methods. Variables including powder particle sizes, dispersant molecular weights (MWs), binders, printing parameters, and post processing were explored as well as the characterization of the physical properties (add specifics here).

36 MATERIALS SCIENCE↗
DOE OSTI2023

Implementation of Smart Materials for Actuation of Traditional Valve Technology for Hybrid Energy Systems

The ever-changing nature of the power industry will require the implementation of hybrid energy systems. Integration of tightly coupled components in hybrids often involves the diversion of exhaust gas flow. An innovative smart material actuation technology is proposed to replace traditional electro-mechanical actuated valve mechanisms with lighter and less expensive actuators. A shape memory alloy (SMA) spring-actuated valve was designed for high-temperature service to demonstrate the promise of smart materials in control valve applications. With SMA springs only generating a maximum force of 3.2 N, an innovative valve design was necessary. To demonstrate the concept, a 3-inch Nominal Pipe Size valve was designed, and 3D printed using the stereolithography technique. Increasing the electrical current to actuate the SMA springs reduced actuation time. The maximum current of 10 A produced the lowest actuation time of 2.85 s, with an observed maximum stroke rate of more than 100 stroke completion %/s (considering actuation open/close as 100% stroke) at the midrange. The final assembly of the valve was estimated to provide a cost reduction of more than 30% and a weight reduction of more than 80% compared to the other available automatic valves in the present market.

36 MATERIALS SCIENCE↗
DOE OSTI2020

An Adaptive-Mesh-Refinement Based Computational Tool for Simulating Catalysis at Mesoscale

In this work, we present a computational tool for mesoscale applications using open-source exascale- computing compatible adaptive-mesh-refinement (AMR) library, AMReX [2]. AMReX is software library that enables development of application solvers with block-structured Cartesian AMR. Our tool has capabilities to include realistic geometry representation, chemical species transport, reactions and thermodynamics that are critical for capturing mesoscale physics. A significant achievement is the ability of our solver to automatically import electron microscopy data in the form of a stereolithography (STL) or pixelated file format (mrc, tiff) without undergoing the tedious task of unstructured mesh generation. This feature allows for rapid simulation of catalyst particles with complex morphologies using an immersed-boundary formulation. The use of AMR allows for higher resolutions at catalyst surface interfaces, which in turn provides an accurate description of surface reactions and transport. Our solver uses a hybrid distributed and shared memory parallelism (OpenMP/GPU-based) with which strong scaling up to 10,000 processors for realistic catalyst particle simulations have been demonstrated.

BIOMASS FUELS,MATHEMATICS AND COMPUTING↗