Results for “standoff” — Page 3

NASA NTRS1991

Solar cycle variations in the size and shape of the magnetopause

The 10 years of the ISEE 1 and 2 mission covering much of solar cycle 21 and the beginning of solar cycle 22 make it possible to study the position, shape, and motion of the magnetopause throughout the course of changing solar activity. The size and shape of the magnetopause were determined for each observing season using the ISEE 1 and 2 magnetometer data IMP 8 data were used to monitor the solar wind changes with the solar cycle. During the 1979-1980 season, at solar maximum, the solar wind dynamic pressure was at its lowest values, and, at solar minimum, the solar wind pressure was at its largest values, more than double the value in the 1979-1980 season. During this solar cycle, the magnetopause was about 0.5 R(E) farther when the interplanetary magnetic field (IMF) was strongly northward, than when strongly southward. Both standoff distance values are fround to be smaller than the value found by Fairfield (1971). The standoff distance of the magnetopause for northward IMF is anticorrelated with the solar wind pressure. However, the standoff distance for southward IMF seems relatively insensitive to solar wind dynamic pressure.

Petrinec, S. P.↗

NASA NTRSDate not supplied

Simultaneous Ice Water Content Measurements at Multiple Locations on the NASA DC-8 Aircraft during the 2018 HIWC RADAR Flight Campaign

Ice water content measurements were made simultaneously at three locations on the NASA DC-8 in natural, glaciated conditions during the 2018 High Ice Water Content RADAR flight campaign. The purpose of these measurements was to further evaluate efficiency factors of hot-wire total water content probes in glaciated conditions and investigate the enhancement of ice crystal concentrations near fuselage surfaces due to flow field inertial effects, and ice crystals impacting the nose, breaking up, and flowing downstream. The total water content measurements were made using either Science Engineering Associates Ice Crystal Detectors or Robust Probes. Three common sensors were mounted on an underwing canister considered to be in near free-flow conditions, a standoff from a fuselage window, and the nose of the fuselage near the pitot probes. The Ice Crystal Detector total water content sensor and Robust Probe sensor collection and retention efficiencies were evaluated through comparisons with the underwing Ice Crystal Detector and Robust Probe measurements to the IKP2 isokinetic evaporator probe, which provided the reference ice water content measurement. Local ice water content at the nose position was evaluated by comparing ratios of the nose and underwing ice crystal detectors to the IKP2. Local ice water content at the window-standoff location was also evaluated by comparing total water content sensor measurements from the window ice crystal detector to the measurements made with the underwing and nose Ice Crystal Detectors The key findings were: 1) the Ice Crystal Detector total water content sensor ice water content efficiency factor was similar to previous estimates, but reduced with increased ice crystal median mass diameter; 2) the ice water content at the fuselage nose location near the DC-8 pitot probes was approximately 2.5 times the freestream values – although this estimate is affected by a higher probe efficiency factor due to smaller particles in the debris cloud from impacts upstream of the probe; and 3) the ice water content at the 17” standoff from the port window varied from about 50% to 3 times freestream values in a complicated manner. Similar measurement locations are not uncommon on cloud research aircraft, where ice particle measurements may be subject to similar uncertainties.

Aircraft Icing↗

NASA NTRSDate not supplied

Simultaneous Ice Water Content Measurements at Multiple Locations on the NASA DC-8 Aircraft during the 2018 HIWC RADAR Flight Campaign

Ice water content measurements were made simultaneously at three locations on the NASA DC-8 in natural, glaciated conditions during the 2018 High Ice Water Content RADAR flight campaign. The purpose of these measurements was to further evaluate efficiency factors of hot-wire total water content probes in glaciated conditions and investigate the enhancement of ice crystal concentrations near fuselage surfaces due to flow field inertial effects, and ice crystals impacting the nose, breaking up, and flowing downstream. The total water content measurements were made using either Science Engineering Associates Ice Crystal Detectors or Robust Probes. Three common sensors were mounted on an underwing canister considered to be in near free-flow conditions, a standoff from a fuselage window, and the nose of the fuselage near the pitot probes. The Ice Crystal Detector total water content sensor and Robust Probe sensor collection and retention efficiencies were evaluated through comparisons with the underwing Ice Crystal Detector and Robust Probe measurements to the IKP2 isokinetic evaporator probe, which provided the reference ice water content measurement. Local ice water content at the nose position was evaluated by comparing ratios of the nose and underwing ice crystal detectors to the IKP2. Local ice water content at the window-standoff location was also evaluated by comparing total water content sensor measurements from the window ice crystal detector to the measurements made with the underwing and nose Ice Crystal Detectors The key findings were: 1) the Ice Crystal Detector total water content sensor ice water content efficiency factor was similar to previous estimates, but reduced with increased ice crystal median mass diameter; 2) the ice water content at the fuselage nose location near the DC-8 pitot probes was approximately 2.5 times the freestream values – although this estimate is affected by a higher probe efficiency factor due to smaller particles in the debris cloud from impacts upstream of the probe; and 3) the ice water content at the 17” standoff from the port window varied from about 50% to 3 times freestream values in a complicated manner. Similar measurement locations are not uncommon on cloud research aircraft, where ice particle measurements may be subject to similar uncertainties.

o Aircraft Icing↗

NASA NTRSDate not supplied

The Effect of Reduced Pressure on the Characteristics of Spreading Flames

Flame spread over solid fuels is a canonical problem in fire science, due to its direct implications on material flammability and importance in fire development. In a microgravity environment, such as onboard a spacecraft, flames can behave very differently than on Earth. This is concerning for spaceflight life safety, especially in higher-oxygen environments. Due to the difficulties associated with microgravity testing, low-pressure environments have been proposed as an alternative to approximately replicate the burning behavior of solid fuels observed in reduced gravity conditions because of similar diffusion and heat transfer mechanisms. However, the roles played by gravity and pressure on flame length, standoff distance, and flame spread rate vary with the burning configuration. In concurrent flame spread, the buoyant flow enhances the spread rate by bringing the flame closer to the fuel surface and increasing the heating of the solid fuel. In opposed flame spread, the sample is preheated by the flame ahead of the flame leading edge, which is strongly affected by the surrounding flow field. In this work, we consider flames spreading over thin cotton samples in both downward (opposed) and upward (concurrent) configurations to investigate the effect of pressure (30-100 kPa) on flame characteristics, such as spread rate and standoff distance. A small forced flow is induced upward so that the flames are exposed to a mixed (forced and free) flow. By reducing pressure, flames become less bright, their standoff distance increases, and their spread rates decrease similar to what is observed in low-gravity environments. These results could in help understanding the differences between flames spreading at low pressure and low gravity environments for these similar, yet very different, spreading configurations. They could also provide more information about potential Earth-based flammability testing of materials for spacecraft applications.

fire safety↗

NASA NTRSDate not supplied

The effect of reduced pressure on the characteristics of spreading flames

Flame spread over solid fuels is a canonical problem in fire science, due to its direct implications on material flammability and importance in fire development. In a microgravity environment, such as onboard a spacecraft, flames can behave very differently than on Earth. This is concerning for spaceflight life safety, especially in higher-oxygen environments. Due to the difficulties associated with microgravity testing, low-pressure environments have been proposed as an alternative to approximately replicate the burning behavior of solid fuels observed in reduced gravity conditions because of similar diffusion and heat transfer mechanisms. However, the roles played by gravity and pressure on flame length, standoff distance, and flame spread rate vary with the burning configuration. In concurrent flame spread, the buoyant flow enhances the spread rate by bringing the flame closer to the fuel surface and increasing the heating of the solid fuel. In opposed flame spread, the sample is preheated by the flame ahead of the flame leading edge, which is strongly affected by the surrounding flow field. In this work, we consider flames spreading over thin cotton samples in both downward (opposed) and upward (concurrent) configurations to investigate the effect of pressure (30-100 kPa) on flame characteristics, such as spread rate and standoff distance. A small forced flow is induced upward so that the flames are exposed to a mixed (forced and free) flow. By reducing pressure, flames become less bright, their standoff distance increases, and their spread rates decrease similar to what is observed in low-gravity environments. These results could in help understanding the differences between flames spreading at low pressure and low gravity environments for these similar, yet very different, spreading configurations. They could also provide more information about potential Earth-based flammability testing of materials for spacecraft applications.

fire safety↗

NASA NTRS2021

Simultaneous Ice Water Content Measurements at Multiple Locations on the NASA DC-8 Aircraft during the 2018 HIWC RADAR Flight Campaign

Ice water content measurements were made simultaneously at three locations on the NASA DC-8 in natural, glaciated conditions during the 2018 High Ice Water Content RADAR flight campaign. The purpose of these measurements was to further evaluate efficiency factors of hot-wire total water content probes in glaciated conditions and investigate the enhancement of ice crystal concentrations near fuselage surfaces due to flow field inertial effects, and ice crystals impacting the nose, breaking up, and flowing downstream. The total water content measurements were made using either Science Engineering Associates Ice Crystal Detectors or Robust Probes. Three common sensors were mounted on an underwing canister considered to be in near free-flow conditions, a standoff from a fuselage window, and the nose of the fuselage near the pitot probes. The Ice Crystal Detector concave total water content sensor and Robust Probe sensor collection and retention efficiencies were evaluated through comparisons with the underwing Ice Crystal Detector and Robust Probe measurements to the Isokinetic Probe version 2 (IKP2), which provided the reference ice water content measurement. Local ice water content at the nose position was evaluated by comparing ratios of the nose and underwing ice crystal detectors to the IKP2. Local ice water content at the window-standoff location was also evaluated by comparing total water content sensor measurements from the window probes to the measurements made with the underwing and nose probes. The key findings were: (1) the Ice Crystal Detector concave water content sensor efficiency factor to glaciated conditions was similar to previous estimates, but reduced with increased ice crystal median mass diameter; (2) the ice water content at the fuselage nose location near the DC-8 pitot probes was approximately 2.5 times the freestream values—although this estimate is affected by a higher probe efficiency factor due to smaller particles in the debris cloud from impacts upstream of the probe; and (3) the ice water content at the 17 in. standoff from the port window varied from about 50 percent to nearly three times freestream values in a complicated manner. Similar measurement locations are not uncommon on cloud research aircraft, where ice particle measurements may be subject to similar uncertainties.

Aircraft Icing↗

NASA NTRSDate not supplied

A Wall-Modeled LES Perspective for the High Lift Common Research Model Using LAVA

A new immersed boundary Wall-Modelled Large Eddy Simulation (WMLES) formulation is developed to study high-lift aerodynamics on the NASA High-Lift Common Research Model (HL-CRM). A sequence of Cartesian Octree grids with sizes ranging from 100 Million through 2.02 Billion grid points is utilized to systematically assess grid-sensitivity and convergence for the in-tunnel (QinetiQ) configuration of the model, and remarkable agreement between the immersed boundary and the curvilinear body-aligned WMLES formulations is reported on grids with comparable resolutions. In the free-air configuration of the model, consistent predictions between the Curvilinear Overset and the Cartesian Octree formulations are reported for angles of attack up to C(L,max) at a=19.57. However, some differences in the onset of stall are seen between the two methods for a>20°: while the curvilinear WMLES experiences wing-root separation with increasing angle of attack (Topology A), the Cartesian Octree formulation shows a different flow topology characterized by boundary layer weakness on the main element, emanating from the pylon-wing attachment (Topology B). In order to obtain further insight into the two-distinct topologies, carefully designed numerical experiments to isolate effects of the model standoff and the tunnel wall-boundary layers are conducted using the immersed boundary WMLES formulation. The increased incidence angle-of-attack on the inboard portion of the wing due to the standoff is shown to be sufficient for triggering a switch from Topology B to Topology A in Cartesian WMLES. The role of the floor boundary layer is further examined in detail by identification of additional corner-flow vorticity generated by the viscous juncture flow interactions between the floor boundary layer and the standoff leading to formation of a strong coherent and persistent vortex on the belly-side of the fuselage. The intensity of this vortex is shown to increase with the thickness of the floor boundary layer. A further increase in the incidence angle of attack near the leading-edge strake caused by the presence of this belly-side vortex is quantified for two-distinct floor boundary layers. Both of the floor boundary layers considered result in the onset of large scale wing-root separation at a=21.47in non-confined (free-air) configurations.

TTT↗

NASA NTRS2010

Fast, High-Resolution Terahertz Radar Imaging at 25 Meters

We report improvements in the scanning speed and standoff range of an ultra-wide bandwidth terahertz (THz) imaging radar for person-borne concealed object detection. Fast beam scanning of the single-transceiver radar is accomplished by rapidly deflecting a flat, light-weight subreflector in a confocal Gregorian optical geometry. With RF back-end improvements also implemented, the radar imaging rate has increased by a factor of about 30 compared to that achieved previously in a 4 m standoff prototype instrument. In addition, a new 100 cm diameter ellipsoidal aluminum reflector yields beam spot diameters of approximately 1 cm over a 50x50 cm field of view at a range of 25 m, although some aberrations are observed that probably arise from misaligned optics. Through-clothes images of a concealed threat at 25 m range, acquired in 5 seconds, are presented, and the impact of reduced signal-to-noise from an even faster frame rate is analyzed. These results inform the system requirements for eventually achieving sub-second or video-rate THz radar imaging.

standoff concealed weapons detection↗

NASA NTRS1972

Thermal design of composite material high temperature attachments

An evaluation has been made of the thermal aspects of utilizing advanced filamentary composite materials as primary structures on the shuttle vehicle. The technical objectives of this study are to: (1) establish and design concepts for maintaining material temperatures within allowable limits at TPS attachments and or penetrations applicable to the space shuttle; and (2) verify the thermal design analysis by testing selected concepts. Specific composite materials being evaluated are boron epoxy, graphite/epoxy, boron polyimide, and boron aluminum; graphite/polyimide has been added to this list for property data identification and preliminary evaluation of thermal design problems. The TPS standoff to composite structure attachment over-temperature problem is directly related to TPS maximum surface temperature. To provide a thermally comprehensive evaluation of attachment temperature characteristics, maximum surface temperatures of 900 F, 1200 F, 1800 F, 2500 F and 3000 F are considered in this study. This range of surface temperatures and the high and low maximum temperature capability of the selected composite materials will result in a wide range of thermal requirements for composite/TPS standoff attachments.

Source record↗

NASA NTRS1976

Some anomalies observed in wind-tunnel tests of a blunt body at transonic and supersonic speeds

An investigation of anomalies observed in wind tunnel force tests of a blunt body configuration was conducted at Mach numbers from 0.20 to 1.35 in the Langley 8-foot transonic pressure tunnel and at Mach numbers of 1.50, 1,80, and 2.16 in the Langley Unitary Plan wind tunnel. At a Mach number of 1.35, large variations occurred in axial force coefficient at a given angle of attack. At transonic and low supersonic speeds, the total drag measured in the wind tunnel was much lower than that measured during earlier ballistic range tests. Accurate measurements of total drag for blunt bodies will require the use of models smaller than those tested thus far; however, it appears that accurate forebody drag results can be obtained by using relatively large models. Shock standoff distance is presented from experimental data over the Mach number range from 1.05 to 4.34. Theory accurately predicts the shock standoff distance at Mach numbers up to 1.75.

Brooks, J. D.↗

NASA NTRS1979

Vapour phase details in the oscillatory combustion of propellants A porous plate analogue

A perforated porous plate burner is designed to scale up the vapor phase details in composite propellant combustion. A fuel vapor is passed through the pores and an oxidizer vapor is passed through the discrete perforations drilled in the plate. Discussion of the scale modeling of the vapor phase details in oscillatory combustion of composite propellants leads to the following conclusions: (1) the concept of a perforated porous plate analog for the composite propellant vapor phase combustion appears to be valid during oscillatory combustion as well; (2) the flame standoff distance can be conveniently determined with motion picture photography; (3) the flame standoff distance varies with the flow velocity during oscillatory combustion much the same way as during time-independent combustion; and (4) the overall structure of the combustion zone (flame) does not appear to vary too much from its time-independent structure during oscillatory combustion

Ramohalli, K.↗

NASA NTRS1981

On the development and global oscillations of cometary ionospheres

Representing the cometary ionosphere by a single fluid model characterized by an average ionization time scale, both the ionosphere's development as a comet approaches the sun and its response to sudden changes in solar wind conditions are investigated. Three different nuclear sizes (small, average, very large) and three different modes of energy addition to the atmosphere (adiabatic, isothermal, suprathermal) are considered. It is found that the crucial parameter determining both the nature and the size of the ionosphere is the average ionization time scale within the ionosphere. Two different scales are identified. It is noted that the ionosphere can also be characterized by the relative sizes of three different scale lengths: the neutral standoff distance from the nucleus, the ion standoff distance from the nucleus, and the nuclear distance at which the ions and the neutrals decouple collisionally.

Houpis, H. L. F.↗

NASA NTRS1981

A low cost maritime control aircraft-ship-weapons system

It is pointed out that the long-range antiship standoff missile is emerging as the foremost threat on the seas. Delivered by high speed bombers, surface ships, and submarines, a missile attack can be mounted against selected targets from any point on the compass. An investigation is conducted regarding the configuration of a system which could most efficiently identify and destroy standoff threats before they launch their weapons. It is found that by using ships for carrying and launching missiles, and employing aircraft with a powerful radar only for search and missile directing operations, aircraft cost and weight can be greatly reduced. The employment of V/STOL aircraft in preference to other types of aircraft makes it possible to use ships of smaller size for carrying the aircraft. However, in order to obtain an all-weather operational capability for the system, ships are selected which are still big enough to display the required stability in heavy seas.

Fluk, H.↗

NASA NTRS1987

The configuration of slow-mode shocks

A simple method for computing blunt-body flows containing slow shocks is presented. The method is based on the solution of a free-boundary problem for the shock configuration that matches a postshock potential flow to a uniform preshock flow. The method is applied to shocks arising from flow about spherical and paraboloidal obstacles. The results of a parametric study of shock formation as a function of sonic and Alfven Mach numbers showed that when either Mach number decreased, the standoff distance increased. The results should give estimates of the location and the configuration of slow shocks, provided that two as yet unverified assumptions are correct: (1) that the standoff distance and the slow-shock configuration along the stagnation streamline are not affected significantly by portions of the shock still forming far upstream of the shock nose, and (2) that fast-mode waves propagating at small angles to the magnetic field do not significantly affect the formation of the slow shock.

Wolfson, Richard↗

NASA NTRS1991

Permanent wire splicing by an explosive joining process

The invention is an apparatus and method for wire splicing using an explosive joining process. The apparatus consists of a prebent, U-shaped strap of metal that slides over prepositioned wires. A standoff means separates the wires from the strap before joining. An adhesive means holds two ribbon explosives in position centered over the U-shaped strap. A detonating means connects to the ribbon explosives. The process involves spreading strands of each wire to be joined into a flat plane. The process then requires alternating each strand in alignment to form a mesh-like arrangement with an overlapped area. The strap slides over the strands of the wires, and the standoff means is positioned between the two surfaces. The detonating means then initiates the ribbon explosives that drive the strap to accomplish a high velocity, angular collision between the mating surfaces. This collision creates surface melts and collision bonding results in electron sharing linkups.

Bement, Laurence J.↗

NASA NTRS1995

Experimental investigation of the inlet detector configuration variation in the flow field at Mach 1.9

In recent years, active research has been conducted to study the technological feasibility of supersonic laminar flow control on the wing of the High Speed Civil Transport (HSCT). For this study, the F-16XL has been chosen due to its highly swept crank wing planform that closely resembles the HSCT configurations. During flights, it is discovered that the shock wave generated from the aircraft inlet introduces disturbances on the wing where the data acquisition is conducted. The flow field about a supersonic inlet is characterized by a complex three dimensional pattern of shock waves generated by the geometrical configuration of a deflector and a cowl lip. Hence, in this study, experimental method is employed to investigate the effects of the variation of deflector configuration on the flow field, and consequently, the possibility of diverting the incoming shock-disturbances away from the test section. In the present experiments, a model composed of a simple circular tube with a triangular deflector is designed to study the deflector length and the deflector base width variation in the flow field. Experimental results indicate that the lowest external pressure ratio is observed at the junction where the deflector lip and the inlet cowl lip merge. Also, it is noted that the external pressure ratio, the internal pressure ratio, the coefficient of spillage drag, and the shock standoff distance decrease as the deflector length increases. In addition, the Redefined Total Pressure Recovery Ratio (RTPRR) increases with an increase in the deflector length. Results from the study of the effect of the deflector's base width variation on the flow field indicate that the lowest external pressure ratio is observed at the junction between the inlet cowl lip and the deflector lip. As the base width of the deflector increases, the external pressure ratio at 0 rotation increases, whereas the external pressure ratio at 180 rotation decreases. In addition, the internal pressure ratio and the coefficient of spillage drag decrease as the base width of the deflector increases. However, RTPRR and shock standoff distance increase as the base width increases. In conclusion, as deflector dimensions vary, distinctive patterns in the pressure variation around the inlet deflector are observed. With an increase in the deflector length and base width, the magnitude of shock-disturbances are weakened due to a decrease in the external pressure ratio. Also, as the deflector length and base width increase, a smaller bow shock angle is formed. Therefore, the inlet shock wave formation would be significantly altered, and consequently, shock disturbances on the wing test section can be avoided through appropriately designing the deflector.

Hwang, Kyu C.↗

NASA NTRS1996

Analysis, design and testing of high pressure waterjet nozzles

The Hydroblast Research Cell at MSFC is both a research and a processing facility. The cell is used to investigate fundamental phenomena associated with waterjets as well as to clean hardware for various NASA and contractor projects. In the area of research, investigations are made regarding the use of high pressure waterjets to strip paint, grease, adhesive and thermal spray coatings from various substrates. Current industrial methods of cleaning often use ozone depleting chemicals (ODC) such as chlorinated solvents, and high pressure waterjet cleaning has proven to be a viable alternative. Standard methods of waterjet cleaning use hand held or robotically controlled nozzles. The nozzles used can be single-stream or multijet nozzles, and the multijet nozzles may be mounted in a rotating head or arranged in a fan-type shape. We consider in this paper the use of a rotating, multijet, high pressure water nozzle which is robotically controlled. This method enables rapid cleaning of a large area, but problems such as incomplete coverage (e.g. the formation of 'islands' of material not cleaned) and damage to the substrate from the waterjet have been observed. In addition, current stripping operations require the nozzle to be placed at a standoff distance of approximately 2 inches in order to achieve adequate performance. This close proximity of the nozzle to the target to be cleaned poses risks to the nozzle and the target in the event of robot error or the striking of unanticipated extrusions on the target surface as the nozzle sweeps past. Two key motivations of this research are to eliminate the formation of 'coating islands' and to increase the allowable standoff distance of the nozzle.

Mazzoleni, Andre P.↗

NASA NTRS1995

Analytic MHD Theory for Earth's Bow Shock at Low Mach Numbers

A previous MHD theory for the density jump at the Earth's bow shock, which assumed the Alfven M(A) and sonic M(s) Mach numbers are both much greater than 1, is reanalyzed and generalized. It is shown that the MHD jump equation can be analytically solved much more directly using perturbation theory, with the ordering determined by M(A) and M(s), and that the first-order perturbation solution is identical to the solution found in the earlier theory. The second-order perturbation solution is calculated, whereas the earlier approach cannot be used to obtain it. The second-order terms generally are important over most of the range of M(A) and M(s) in the solar wind when the angle theta between the normal to the bow shock and magnetic field is not close to 0 deg or 180 deg (the solutions are symmetric about 90 deg). This new perturbation solution is generally accurate under most solar wind conditions at 1 AU, with the exception of low Mach numbers when theta is close to 90 deg. In this exceptional case the new solution does not improve on the first-order solutions obtained earlier, and the predicted density ratio can vary by 10-20% from the exact numerical MHD solutions. For theta approx. = 90 deg another perturbation solution is derived that predicts the density ratio much more accurately. This second solution is typically accurate for quasi-perpendicular conditions. Taken together, these two analytical solutions are generally accurate for the Earth's bow shock, except in the rare circumstance that M(A) is less than or = 2. MHD and gasdynamic simulations have produced empirical models in which the shock's standoff distance a(s) is linearly related to the density jump ratio X at the subsolar point. Using an empirical relationship between a(s) and X obtained from MHD simulations, a(s) values predicted using the MHD solutions for X are compared with the predictions of phenomenological models commonly used for modeling observational data, and with the predictions of a modified phenomenological model proposed recently. The similarities and differences between these results are illustrated using plots of X and a(s) predicted for the Earth's bow shock. The plots show that the new analytic solutions agree very well with the exact numerical MHD solutions and that these MHD solutions should replace the corresponding phenomenological relations in comparisons with data. Furthermore, significant differences exist between the standoff distances predicted at low M(A) using the MHD models versus those predicted by the new modified phenomenological model. These differences should be amenable to observational testing.

Grabbe, Crockett L.↗