Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “stagnant”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Simple device modification simultaneously enhances indoor passive evaporative cooling power and duration

Passive evaporative cooling from a damp cloth or vessel can be used for localized cooling of perishables such as food and medicine, drinking water, and even people. Such applications have two key objectives, which are normally in tension with each other: minimizing the water consumption rate and maximizing the cooling (steady-state temperature swing between the cool cloth and the warm surroundings). Here, we present a simple device that delivers higher performance in both metrics simultaneously by adding a perforated aluminum foil sheet suspended over a stagnant air layer to thermally shield the evaporating surface while also facilitating mass transfer. Experimental results demonstrate a simultaneous 10%–25% increase in temperature swing and 2–3× reduction in water consumption rate as compared to conventional evaporative cooling. This improvement is achieved through careful modeling to optimize the coupled heat and mass transfer through the airgap (thermally insulating and vapor permeable) and perforated foil (infrared reflective and vapor permeable).

Chen, Sarah Mizuno↗
DOE OSTI2023

Impact of Flow Configurations on Response Time and Data Quality in Real-Time, In-Line Fourier Transform Infrared (FTIR) Monitoring of Viscous Flows

The real-time, in-line monitoring of continuous flow concentrations is widely conducted via infrared (IR) spectrometry by using a flow cell connected to a reactive flow stream. For protective purposes, the IR sensor tip is typically offset from the flow. This offset can cause the formation of a stagnant boundary layer above the sensor, especially when dealing with high-viscosity fluids. As a result, the IR signal response time is often controlled by the slow diffusional exchange of fluid in the boundary layer, as confirmed via 2D computational fluid dynamics (CFD) simulations. We evaluated several flow configuration modifications in a typical IR flow cell in order to identify the changes to the flow dynamics that enable improved response times with minimal changes to the cell configuration: the use of (i) vertical flow, where the standard horizontal flow over the sensor is redirected to contact vertically with the sensor, (ii) a static mixer to create radial flow momentum above the IR sensor, and (iii) horizontal or vertical nozzles to direct the flow toward the IR sensor. The vertical flow configuration did not show any significant improvement over the standard horizontal flow configuration. However, the static mixer, horizontal nozzle, and vertical nozzle configurations all resulted in markedly improved response times and signal quality, albeit at the expense of a higher pressure drop across the flow cell. These results point toward straightforward, user-accessible modifications of in-line IR flow cells that result in significant improvements in signal stability and acquisition times.

42 ENGINEERING↗
DOE OSTI2025

Bridging the Gap in Carbon Free Iron Making: How Hydrogen Affects the Reduction of Iron Ore between 900 and 1590 °C

Hydrogen-based reduction of iron ore for iron and steel production has emerged as a promising alternative to coal and natural gas. Unlike other hydrogen-based iron ore reduction studies, this research focuses on a wide temperature range across 900–1590 °C, encompassing reduction in solid, mixed, and liquid (slag) phases. For a 20 min exposure to hydrogen, the reduction degree increased monotonically from ∼35% at 900 °C to >90% at 1550 °C, except between 1100 °C and 1400 °C, where it stagnated ∼60%. This experimental work challenges the widely accepted notion that higher temperatures enhance the reduction process. Instead, it reveals an overlooked kinetic bottleneck, suggesting complex thermodynamic and mass transfer limitations influenced by phase transformations, diffusion barriers, and microstructural changes. Density functional theory-based molecular dynamics simulations indicate that oxygen diffusivity in BCC iron is 3.88 × 10 –5 cm 2 /s which is ∼5–10 times higher than that in FCC iron. This study reports that this stagnant reduction degree in the mixed solid–liquid phase is due to competition of multiple mechanisms, such as surface- and bulk-diffusion, pore collapse mechanisms, and crystallographic transitions.

08 HYDROGEN↗
DOE OSTI2024

The Abundance and Sources of Ice Nucleating Particles Within Alaskan Ice Fog

Abstract The Alaskan Layered Pollution and Chemical Analysis (ALPACA) field campaign included deployment of a suite of atmospheric measurements in January–February 2022 with the goal of better understanding atmospheric processes and pollution under cold and dark conditions in Fairbanks, Alaska. We report on measurements of particle composition, particle size, ice nucleating particle (INP) composition, and INP size during an ice fog period (29 January–3 February). During this period, coarse particulate matter (PM 10 ) concentrations increased by 150% in association with a decrease in air temperature, a stronger temperature inversion, and relatively stagnant conditions. Results also show a 18%–78% decrease in INPs during the ice fog period, indicating that particles had activated into the ice fog via nucleation. Peroxide and heat treatments performed on INPs indicated that, on average, the largest contributions to the INP population were heat‐labile (potentially biological, 63%), organic (31%), then inorganic (likely dust, 6%). Measurements of levoglucosan and bulk and single‐particle composition corroborate the presence of dust and aerosols from combustion sources. Heat‐labile and organic INPs decreased during the peak period of the ice fog, indicating those were preferentially activated, while inorganic INPs increased, suggesting they remained as interstitial INPs. In general, INP concentrations were unexpectedly high in Fairbanks compared to other locations in the Arctic during winter. The fact that these INPs likely facilitated ice fog formation in Fairbanks has implications for other high latitude locations subject to the hazards associated with ice fog.

Meteorology & Atmospheric Sciences↗
DOE OSTI2021

Global relationships between crop diversity and nutritional stability

Nutritional stability – a food system’s capacity to provide sufficient nutrients despite disturbance – is an important, yet challenging to measure outcome of diversified agriculture. Using 55 years of data across 184 countries, we assemble 22,000 bipartite crop-nutrient networks to quantify nutritional stability by simulating crop and nutrient loss in a country, and assess its relationship to crop diversity across regions, over time and between imports versus in country production. We find a positive, saturating relationship between crop diversity and nutritional stability across countries, but also show that over time nutritional stability remained stagnant or decreased in all regions except Asia. These results are attributable to diminishing returns on crop diversity, with recent gains in crop diversity among crops with fewer nutrients, or with nutrients already in a country’s food system. Finally, imports are positively associated with crop diversity and nutritional stability, indicating that many countries’ nutritional stability is market exposed.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Human TRPV1 structure and inhibition by the analgesic SB-366791

Pain therapy has remained conceptually stagnant since the opioid crisis, which highlighted the dangers of treating pain with opioids. An alternative addiction-free strategy to conventional painkiller-based treatment is targeting receptors at the origin of the pain pathway, such as transient receptor potential (TRP) ion channels. Thus, a founding member of the vanilloid subfamily of TRP channels, TRPV1, represents one of the most sought-after pain therapy targets. The need for selective TRPV1 inhibitors extends beyond pain treatment, to other diseases associated with this channel, including psychiatric disorders. Here we report the cryo-electron microscopy structures of human TRPV1 in the apo state and in complex with the TRPV1-specific nanomolar-affinity analgesic antagonist SB-366791. SB-366791 binds to the vanilloid site and acts as an allosteric hTRPV1 inhibitor. SB-366791 binding site is supported by mutagenesis combined with electrophysiological recordings and can be further explored to design new drugs targeting TRPV1 in disease conditions.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Persistent meanders and eddies lead to quasi-steady Lagrangian transport patterns in a weak western boundary current

The Brazil Current (BC) is a weak western boundary current flowing along the Southwestern Atlantic Ocean. It is frequently described as a flow with intense mesoscale activity and relatively low volume transport between 5.0 and 10.0 Sv. We use a 13-year eddy-resolving primitive-equation simulation to show that the presence of persistent meanders and eddies leads to characteristic quasi-steady Lagrangian transport patterns, aptly extracted through climatological Lagrangian Coherent Structures (cLCS). The cLCS position the surface expression of the BC core along the 2000-m isobath, in excellent visual agreement with high resolution satellite sea-surface temperature and the model Eulerian mean velocity. The cLCS deformation pattern also responds to zonally persistent cross-shelf SSH transition from positive (high) values near coastline to low (negative) values between 200- and 2000-m and back to positive (high) offshore from the 2000-m isobath. Zonally-paired cyclonic and anticyclonic structures are embedded in this transition, also causing the cLCS to deform into chevrons. An efficient transport barrier is identified close to the 200-m isobath confirmed by limited inshore movement of drogued drifters and accurately indicated by an along slope maxima of climatological strength of attraction. We also show that the persistent cyclonic and anticyclonic structures may induce localized cross-shelf transport. Regions of low climatological strength of attraction coincide with large shelves and with stagnant synthetic trajectories. We also show that cLCS accurately depict trajectories initiated at the location of Chevron’s spill (November 2011) as compared to synthetic and satellite-tracked trajectories, and the outline of the oil from that accident. There is also an agreement between the large-scale oil slicks reaching the Brazilian beaches (from August 2019 to February 2020) and the strength of climatological attraction at the coast. Our work also clarifies the influence of persistent mesoscale structures on the regional circulation. The identification and quantitative description of climatological Lagrangian coherent structures is expected to improve the effectiveness of future emergency response to oil spills, contingency planning, rescue operations, larval and fish connectivity assessment, drifter launch strategies, waste pollutant and marine debris dispersion and destination.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Fluid structure interaction of a subaqueous pendulum: Analyzing the effect of wake correction via large eddy simulations

The dynamic behavior of a subaqueous cylindrical pendulum and corresponding flow dynamics are investigated. The objectives were twofold: (i) to examine whether the two-dimensional model equations sufficiently capture the three-dimensional dynamics and (ii) to investigate the emerging three-dimensional vortical flow structures. Large eddy simulations with two-way coupling fluid structure interaction were carried out using the immersed boundary method to simulate the motion of the pendulum and its interactions with the initially stagnant water. The resulting pendulum motion is compared against measured data obtained in a series of experimental tests to validate the simulation results and the model equations with and without wake corrections. An analysis of the flow vorticity revealed the development of a vortex ring during the first swing and the formation of tip vortices. The evolution of the vortex rings emerging from the motion of the subaqueous cylindrical pendulum was visualized using Q-criteria showing a reasonable agreement with vortical structures observed in the experiment using particle imaging velocimetry. The hydrodynamic moments acting on the simulated pendulum and the moments calculated from the model equations are analyzed. Using the insights from these numerical simulations, a modification of the wake correction is proposed to enhance the accuracy of the rate of decay and period. The transient effect of coherent flow on pendulum dynamics, especially the added mass effect, is discussed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Lagrangian dynamics of particle transport in oral and nasal breathing

Here, we present a large-eddy simulation (LES) of saliva particle transport during normal human breathing through the nose and mouth. The flow of the air–saliva mixture is modeled using an Eulerian LES that is coupled with a Lagrangian particle tracking module to obtain trajectories of saliva particles in a room with stagnant air conditions. The coupled Eulerian–Lagrangian simulation yields novel insights into the intricate dynamics of Lagrangian coherent structures (LCS) and fundamental material lines that emerge from the saliva particles' trajectories during several breathing cycles. Further, we systematically compare the quantitative LCS diagnostics of mouth breathing with those of mouth and nose normal breathing. Analyzing the simulation results of human breathing from the mouth and nose, we show that, soon after the first breathing cycle, saliva particles form a series of roll-up vortex rings that propagate forward. The forward propagation of these vortex rings leads to the formation of an asymmetrical primary forefront vortex. The individual vortex rings continuously propagate forward, merging with the forefront vortex, and ascending along the limb of the leading vortex.

42 ENGINEERING↗
DOE OSTI2024

Electrical and thermal characteristics of LaB6 thermionic hollow cathodes operating in He, D2, Ar, and Xe at 4–200 Pa and 0.25–5 A cm−2

We report characteristics of lanthanum hexaboride (LaB6) cathodes for conditions relevant to a high-voltage, high-current switching device. LaB6 is selected because of its relatively low work function, stability in the presence of many common gas impurities, and a low evaporation rate (long life) at operating temperatures. We have investigated the effect of cathode geometry, gas type, pressure, and current on a LaB6 hollow cathode in a diode configuration with an opposing planar anode. The gas is stagnant at a relatively low pressure of 4–200 Pa (0.03–1.5 Torr) because of device high-voltage standoff requirements. In all cases, the plasma voltage decreases to a plateau value with increasing current where a practical device would operate. The plateau voltage aligns with the fill gas excitation or ionization voltage, depending on conditions. At high current, the cathode temperature exceeds that required for thermionic emission to supply the total current, a behavior that is understood by accounting for back-diffusing bulk electrons.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Incorporating the molecular-scale into a hydrodynamic description of confined aqueous systems

Hydrodynamics provides a continuum-level description of fluid motion, but its applicability at the nanoscale becomes uncertain due to the emerging importance of molecular-level effects such as spatial heterogeneity. Hydrodynamic boundary conditions that incorporate molecular details allow us to partition the system into a near-wall region and a bulk fluid region. We identify a hydrodynamic wall located inside the fluid that determines where slip begins. By extending the hydrodynamic wall with the slip length, the position of the extrapolated wall is established. This offers a unified description of both slip and stagnant flow behaviors, with wall hydrophobicity characterized by the relative location of the extrapolated wall with respect to the physical wall. Employing this concept in analyses of equilibrium molecular dynamics (MD) and non-equilibrium MD simulations of Couette and Poiseuille flows, our results demonstrate consistency between equilibrium and non-equilibrium approaches across different flow types and confinement levels. This demonstrates the robust nature of linear response theory. We then explore the effects of fluid-wall and bulk fluid interactions on the hydrodynamic properties. These findings enhance the effectiveness of molecular-based simulations for investigating complex confined systems in nanofluidics, biology, and colloidal science, offering a complementary molecular-scale perspective to traditional continuum approaches.

flow simulations↗
DOE OSTI2020

The internal structure and geodynamics of Mars inferred from a 4.2-Gyr zircon record

Combining U–Pb ages with Lu–Hf data in zircon provides insights into the magmatic history of rocky planets. The Northwest Africa (NWA) 7034/7533 meteorites are samples of the southern highlands of Mars containing zircon with ages as old as 4476.3 ± 0.9 Ma, interpreted to reflect reworking of the primordial Martian crust by impacts. We extracted a statistically significant zircon population (n= 57) from NWA 7533 that defines a temporal record spanning 4.2 Gyr. Ancient zircons record ages from 4485.5 ± 2.2 Ma to 4331.0 ± 1.4 Ma, defining a bimodal distribution with groupings at 4474 ± 10 Ma and 4442 ± 17 Ma. We interpret these to represent intense bombardment episodes at the planet’s surface, possibly triggered by the early migration of gas giant planets. The unradiogenic initial Hf-isotope composition of these zircons establishes that Mars’s igneous activity prior to ~4.3 Ga was limited to impact-related reworking of a chemically enriched, primordial crust. A group of younger detrital zircons record ages from 1548.0 ± 8.8 Ma to 299.5 ± 0.6 Ma. The only plausible sources for these grains are the temporally associated Elysium and Tharsis volcanic provinces that are the expressions of deep-seated mantle plumes. The chondritic-like Hf-isotope compositions of these zircons require the existence of a primitive and convecting mantle reservoir, indicating that Mars has been in a stagnant-lid tectonic regime for most of its history. Our results imply that zircon is ubiquitous on the Martian surface, providing a faithful record of the planet’s magmatic history.

58 GEOSCIENCES↗
DOE OSTI2025

The glass-ceiling convective regime and the origin and diversity of coronae on Venus

Venus and Earth are rocky planets of roughly the same size and bulk density, yet their surface volcanic and tectonic features appear substantially different. On Venus, the coexistence of large volcanic highlands—interpreted as the surface expression of long-lived mantle plumes—alongside coronae, smaller features thought to be caused by transient thermal diapirs, remains enigmatic. Using two-dimensional numerical models of mantle convection with sharp and broad mineral phase transitions for pyrolite, we show that both scales of upwellings can be generated in a stagnant lid planet with an interior temperature 250 to 400 K warmer than Earth’s. The smaller plumes originate from a ~600 km deep internal layer that exists as a consequence of the different sequence of mineral phase transitions that occur in warmer mantles less processed and differentiated by partial melting and volcanism. Future models that include melting will provide further tests of our hypothesis.

Science & Technology - Other Topics↗
DOE OSTI2022

Influence of Heat Treatments on the Near-Surface Tritium Concentration Profiles

Austenitic stainless steel, type 316, absorbs significant quantities of tritium into the near surface (<1 μm) on exposure to tritium containing gases at room temperature. The tritium concentrations that develop in the near-surface region (<1 μm) are shown to persist for several years without changing. The current work shows the effect of heat treatments on the near-surface tritium-concentration profiles in stainless steel. Identical stainless-steel samples were exposed to tritium at room temperature and then were heated to different temperatures between 100 and 300°C for two hours under a stagnant argon atmosphere. After this initial preheating, the concentration profiles in the first 10 μm were measured by using a combination of a ZnCl2 wash and an etching procedure. Tritium was thermally released by heating the samples to 550°C to measure the residual tritium present in the bulk of the sample. The data show two dominant features. First, preheating causes tritium to migrate both out of the sample and deeper than >1 μm into the bulk. Furthermore, this effect increases with increasing temperature. Second, depletion of tritium from the near surface does not occur until a temperature of 200°C.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Experimental and Numerical Investigation of Flow Boiling in Additive Manufactured Foam Structures With Vapor Pathways

Abstract The unique properties of metal foams make them potential candidates for a range of applications, including microsystem thermal management. Using additive manufacturing to create foam-type structures can improve upon prior thermal solutions by eliminating thermal interface materials and allowing for customization/local control of parameters. In the present investigation, flow boiling in additive-manufactured metal foams is investigated both experimentally and numerically. Two test samples, one with uniform structure and the other with pathways for vapor removal, are compared both experimentally and numerically. A conjugate computational fluid dynamics and heat transfer (CFD-HT) model utilizing a three-dimensional volume of fluid (VOF) model with accompanying evaporation/condensation model provided in-depth visualization of the boiling flow phenomena. The experiments generated the thermohydraulic performance over a range of heat fluxes, demonstrating that the sample incorporating dedicated vapor pathways performed better in both pressure and heat transfer performance metrics compared to the uniform foam. Additionally, negative system-level effects (i.e., hydraulic oscillations) were shown to be abated using the vapor removal structures. The numerical model yielded further insight into the factors contributing to the improved performance. Results indicated the pathways functioned as vapor removal channels, allowing the generated vapor to vent from the foam structure into the lanes. Further computational investigations demonstrated changes in flow regimes, where the addition of vapor channels caused the flow to change from churn to annular. Bubble behavior unique to the vapor pathway structure was studied, showing stagnant regions that eject vapor into the channel.

Engineering↗
DOE OSTI2021

Feasibility of Lead Fast Reactor Heat Exchanger Tube Online Monitoring

Within virtually all reactor systems with heat exchangers, the thinnest barriers between primary and secondary fluids are the heat exchanger tubes. Consistent with light water reactor experience, the advanced reactor heat exchangers are the most susceptible regions for corrosion and leakage (NRC, 2019). Moreover, traditional inspections and repairs using robotics will be expensive or impractical. On-line structural health corrosion monitoring (OLSHM) is therefore desirable to detect tube degradation prior to leaks that may allow mixing of heat exchanger fluids. Rhetorically many molten salt reactor (MSR) designers plan for on-line monitoring of critical reactor components including heat exchangers but there are no proven OLSHM sensors or systems for MSR heat exchangers. Guided wave ultrasound from the tube-end or ID using conventional low-temperature piezoelectric sensors has been shown to be sensitive to pits and cracks less than 50% through-wall in long pipes and tubes (Narayanan M.M., 2019) . Mode and frequency selection are important for practical sensor design decisions and ultimate performance. The L-0 wave-mode is easily excited by L-mode transducers but they have surface normal wave motion that will be sensitive to and more attenuative because of fluid interaction with the tube surface (Rose J.L., 1994). Shear Horizontal (SH) wave modes have material motion parallel to the tube surface therefore are virtually unaffected by fluid interaction. For SH-0 to be nondispersive in steel, the frequency-thickness product (MHz-mm) must be less than approximately 1.5. SH mode transducers must be coupled by a material that can support shear stress; a thin layer of honey works well for temporary sensors and an adhesive or a brazed metallurgical bond for permanent sensors. If sensors are incorporated into the fabrication process, the same kinds of SH-0 waves can be generated from the stagnant flow area of the tube OD without compromising the heat-exchange tube function. Piezoelectric materials are also available that can withstand harsh temperatures of molten salt heat exchangers (Stevenson T., 2015) (Machura et al., 2008). Though they may not have as high-performance characteristics, their performance only needs to be good enough to detect flaws of interest. This project attempts to demonstrate feasibility to develop a sensor that can be sensitive to flaws of interest and perform long-term monitoring of a molten salt reactor heat exchanger. Benefits to the advanced reactor system include: • Minimizing the expense of a reactor shut down for periodic inspection—only shutdown for cause. • Reduce risk of unexpected tube rupture by detecting flaws before they grow to through-wall leaks. • Cost reduction by minimizing need to design for manual/robotic inspectability. Transducer design, characterization of the beam profile, wedges vs. direct application of piezoelectric sensors, and ultrasonic pulse-echo responses from a representative heat exchange tube with fabricated flaw types are discussed.

On-Line Tube Monitor, Guided Wave Ultrasound, SH-0↗
DOE OSTI2022

Improved Representation of Horizontal Variability and Turbulence in Mesoscale Simulations of an Extended Cold-Air Pool Event

Abstract Cold-air pools (CAPs), or stable atmospheric boundary layers that form within topographic basins, are associated with poor air quality, hazardous weather, and low wind energy output. Accurate prediction of CAP dynamics presents a challenge for mesoscale forecast models in part because CAPs occur in regions of complex terrain, where traditional turbulence parameterizations may not be appropriate. This study examines the effects of the planetary boundary layer (PBL) scheme and horizontal diffusion treatment on CAP prediction in the Weather Research and Forecasting (WRF) Model. Model runs with a one-dimensional (1D) PBL scheme and Smagorinsky-like horizontal diffusion are compared with runs that use a new three-dimensional (3D) PBL scheme to calculate turbulent fluxes. Simulations are completed in a nested configuration with 3-km/750-m horizontal grid spacing over a 10-day case study in the Columbia River basin, and results are compared with observations from the Second Wind Forecast Improvement Project. Using event-averaged error metrics, potential temperature and wind speed errors are shown to decrease both with increased horizontal grid resolution and with improved treatment of horizontal diffusion over steep terrain. The 3D PBL scheme further reduces errors relative to a standard 1D PBL approach. Error reduction is accentuated during CAP erosion, when turbulent mixing plays a more dominant role in the dynamics. Last, the 3D PBL scheme is shown to reduce near-surface overestimates of turbulence kinetic energy during the CAP event. The sensitivity of turbulence predictions to the master length-scale formulation in the 3D PBL parameterization is also explored. Significance Statement In this article, we demonstrate how a new framework for modeling atmospheric turbulence improves cold pool predictions, using a case study from January 2017 in the Columbia River basin (U.S. Pacific Northwest). Cold pools are regions of cold, stagnant air that form within valleys or basins, and improved forecasts could help to mitigate the risks they pose to air quality, transportation, and wind energy production. For the chosen case study, our tests show a reduction in temperature and wind speed errors by up to a factor of 2–3 relative to standard model options. These results strongly motivate continued development of the framework as well as its application to other complex weather events.

17 WIND ENERGY↗
DOE OSTI2022

Online Lead/Water Heat Exchanger Sensor/System Feasibility-PNNL (Final Report)

On-line structural health corrosion monitoring in advanced lead fast reactor heat exchangers and molten salt reactor heat exchangers is desirable for detecting tube degradation prior to leaks that may allow mixing of heat exchanger fluids or release of radiological contamination beyond the design containment boundary. This program, On-Line Lead/Water Heat Exchanger Sensor/System Feasibility – PNNL 76092, demonstrates feasibility for an ultrasonic torsional wave mode sensor attached to the outside of a long (30.5-m) heat exchanger tube in the stagnant flow area where the tube joins a heat exchanger plenum and where it is possible to protect a sensor and cable from high-force flows. The sensor must be cable connected to a monitoring instrument near the heat exchanger. The sensor and cable management approach for periodic in-service inspection will be impractical to implement on existing heat exchangers; rather permanently mounted sensors must be installed in conjunction with heat exchanger fabrication. Previous work has shown low-temperature lead zirconate titanate (PZT) piezoceramic sensors are able to detect anomalies of interest in 3.0-m long tubes. These sensors have hereby been extended to a 30.5-m long tube more representative of commercial power heat exchanger designs. The program will continue to investigate higher temperature piezoelectric ceramics and long-term performance of high temperature adhesives and sealants and mechanical pressure coupling for 350-500 °C lead reactor environments and higher temperature (700 °C) molten salt environments.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗