Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solution deposition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Quick Look Report of Godiva U233 shot March 2022 Data Collection Activities

This report discussing the March 2022 irradiation of U233 on the Godiva critical assembly using burst mode and subsequent analysis of the fission products starting at 65 minutes post irradiation, and ending 12 days later. The Short-Lived Fission Product Yield (SLFPY) project is one of many efforts under the Nuclear Physics Multi-Lab and related Venture Project. The objective of the SLFPY project is to provide improved measurements of fission product yields for select nuclides. The SLFPY project consists of measurement and analysis campaigns. To produce fission data, samples of actinide material are irradiated in a high-flux neutron environment. These samples are quickly placed in front of a detection system where both gamma singles and coincidence spectra are collected as a function of time. Gamma spectroscopy is performed on the irradiated material on site near the irradiation facility, starting as soon as feasible after the irradiation and continuing for 7 days or longer. Following the data collection, time-dependent fission yield analyses are performed using gamma-ray spectroscopy. This document summarizes the measurement campaign performed March 21 - April 4, 2022 where sub-gram quantities of 233 U nitrate (UO 2 (NO 3 ) 2 ) were irradiated in the Godiva reactor. The Godiva burst #2076 conducted under experiment IER 504 had a temperature change of +156 degrees Celsius, lasted 13.32 microseconds, and had a reactivity of $\$$1.089. The targets consisted of uranium oxide solution deposited in a quartz tube and packed with quartz wool. The flame-sealed quartz ampoules were used to contain the uranium samples for the irradiation and count activities. On March 22, 2022, at 10:27:00 a.m. the three uranium ampoules, along with a witness foil pack, were irradiated in the Godiva critical assembly using burst mode operations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Fabricating Silver Nanowire–IZO Composite Transparent Conducting Electrodes at Roll-to-Roll Speed for Perovskite Solar Cells

This study addresses the challenges of efficient, large-scale production of flexible transparent conducting electrodes (TCEs). We fabricate TCEs on polyethylene terephthalate (PET) substrates using a high-speed roll-to-roll (R2R) compatible method that combines gravure printing and photonic curing. The hybrid TCEs consist of Ag metal bus lines (Ag MBLs) coated with silver nanowires (AgNWs) and indium zinc oxide (IZO) layers. All materials are solutions deposited at speeds exceeding 10 m/min using gravure printing. We conduct a systematic study to optimize coating parameters and tune solvent composition to achieve a uniform AgNW network. The entire stack undergoes photonic curing, a low-energy annealing method that can be completed at high speeds and will not damage the plastic substrates. The resulting hybrid TCEs exhibit a transmittance of 92% averaged from 400 nm to 1100 nm and a sheet resistance of 11 Ω/sq. Mechanical durability is tested by bending the hybrid TCEs to a strain of 1% for 2000 cycles. The results show a minimal increase (<5%) in resistance. The high-throughput potential is established by showing that each hybrid TCE fabrication step can be completed at 30 m/min. We further fabricate methylammonium lead iodide solar cells to demonstrate the practical use of these TCEs, achieving an average power conversion efficiency (PCE) of 13%. The high-performance hybrid TCEs produced using R2R-compatible processes show potential as a viable choice for replacing vacuum-deposited indium tin oxide films on PET.

14 SOLAR ENERGY↗
DOE OSTI2025

Tuning 3-D Nanomaterial Architectures Using Atomic Layer Deposition to Direct Solution Synthesis

The ability to synthesize nanoarchitected materials with tunable geometries provides a means to control their functional properties, with applications in biological, environmental, and energy fields. To this end, various bottom-up and top-down synthesis processes have been developed. However, many of these processes require prepatterning or etching steps, making them challenging to scale-up to complex, nonplanar substrates. Furthermore, the ability to integrate nanomaterials into hierarchical arrays with precise control of feature spacing and orientation remains a challenge. One approach to overcome these patterning challenges is the use of surface modification layers to guide the resulting geometry of nanomaterial architectures grown from the substrate. A powerful strategy to accomplish this is what we will refer to as “surface-directed assembly,” where the resulting geometric parameters (feature size, shape, orientation) are predetermined by the initial surface layer. In particular, the use of Atomic Layer Deposition (ALD) to form a surface layer, followed by solution-based growth processes, has the ability to synthesize architected structures with tunable geometries on complex, nonplanar surfaces. Over the past decade, we have reported a series of studies where surface-directed assembly is used to synthesize ZnO nanowires (NWs) on top of a variety of substrates. In this case, a thin film of ZnO is deposited onto the substrate using ALD, which can guide the NW diameter, spacing, and angular orientation with respect to the substrate by controlling epitaxial relationships. Furthermore, we have shown that by depositing a submonolayer overcoat of a secondary material (e.g., amorphous TiO 2 ), nucleation sites are partially blocked, which can further tune the spacing between nanowires while minimizing changes to their other geometric properties. This approach can be used to generate multilevel hierarchical structures, such as hyperbranched NW arrays with tunable control of each level of hierarchy using ALD. Finally, we have demonstrated that the tunable control of geometric parameters can be scaled-up to curved, nonplanar substrates. This highlights the power of ALD to conformally and uniformly deposit the seed layers on complex substrates with subnanometer precision. To complement these seeded hydrothermal approaches, we expanded this strategy to include conversion chemistry of the initial ALD seed layers. For example, by replacing ZnO with Al 2 O 3 as the seed layer without changing the hydrothermal growth conditions, Al–Zn layered-double hydroxide nanosheets can be formed instead of nanowires. In another example of conversion chemistry, a solution anion-exchange process was used to incorporate sulfur into ALD metal oxide films. In both of these conversion processes, the properties of the initial ALD film enabled tuning of the resulting nanostructure geometry. In this Account, we describe the use of ALD to guide the growth of diverse nanomaterial systems, with tunable control over their geometry and composition. We further show how these approaches can be used to tune functional properties for a range of applications, including superomniphobic surfaces, antibiofouling coatings, and photocatalysis. In conclusion, we conclude with an outlook on how the combination of ALD and solution synthesis can enable future directions in scalable nanomanufacturing to overcome the limitations of traditional top-down and bottom-up approaches.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

The critical role of configurational flexibility in facilitating reversible reactive metal deposition from borohydride solutions

Development of calcium metal batteries has been historically frustrated by a lack of electrolytes capable of supporting reversible calcium electrodeposition. In this paper, we report the study of an electrolyte consisting of Ca(BH 4 ) 2 in tetrahydrofuran (THF) to gain important insight into the role of the liquid solvation environment in facilitating the reversible electrodeposition of this highly reactive, divalent metal. Through interrogation of the Ca 2+ solvation environment and comparison with Mg 2+ analogs, we show that an ability to reversibly electrodeposit metal at reasonable rates is strongly regulated by dication charge density and polarizability. Our results indicate that the greater polarizability of Ca 2+ over Mg 2+ confers greater configurational flexibility, enabling ionic cluster formation via neutral multimer intermediates. Increased concentration of the proposed electroactive species, CaBH 4 + , enables rapid and stable delivery of Ca 2+ to the electrode interface. Finally, this work helps set the stage for future progress in the development of electrolytes for calcium and other divalent metal batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Method of making a photovoltaic device on a substrate at high speed with perovskite solution

A continuous inline method for production of photovoltaic devices at high speed includes: providing a substrate; depositing a first carrier transport solution layer with a first carrier transport deposition device to form a first carrier transport layer on the substrate; depositing a Perovskite solution comprising solvent and perovskite precursor materials with a Perovskite solution deposition device on the first carrier transport layer; drying the deposited Perovskite solution to form a Perovskite absorber layer; and depositing a second carrier transport solution with a second carrier transport deposition device to form a second carrier transport layer on the Perovskite absorber layer, wherein the deposited Perovskite solution is dried at least partially with a fast drying device which causes a conversion reaction and the Perovskite solution to change in optical density by at least a factor of 2 in less than 0.5 seconds after the fast drying device first acts on the Perovskite solution.

Christensen, Scott Kenneth↗
DOE OSTI2021

Method of making a perovskite layer at high speed

A method of making a perovskite layer includes providing a flexible substrate; providing a perovskite solution comprising an initial amount of solvent and perovskite precursor materials and a total solids concentration between 30 percent and 70 percent by weight of its saturation concentration; depositing the perovskite solution on the flexible substrate; removing a first portion of the solvent from the deposited perovskite solution and increasing the total solids concentration of the perovskite solution to at least 75 percent of its saturation concentration with a first drying step; and removing a second portion of the solvent from the deposited perovskite solution with a second drying step having a higher rate of solvent evaporation that causes saturation and a conversion reaction in the deposited perovskite solution resulting in perovskite crystal formation or formation of a perovskite intermediate phase, wherein the first drying step dwell time is at least 5 times longer than the second drying step dwell time.

Christensen, Scott Kenneth↗
DOE OSTI2024

Comparing the MELCOR Aerosol Deposition Model with Exact Analytical Solutions

Exact analytical solutions are presented for the evolution of the aerosol particle mass density function in a control volume for particle deposition due to gravitational settling, thermophoresis, and diffusion. The solutions are for arbitrary initial mass density functions and are applied for an initial lognormal density function. Integration of these solutions provides the suspended mass in the control volume as a function of time. These solutions serve as an exact benchmark to assess the accuracy of numerical methods. For the numerical algorithm used in MELCOR, excellent agreement is obtained for gravitational settling, diffusive deposition, and thermophoretic deposition for the suspended aerosol mass. In all cases, the default number of discrete particle size bins of 10 is shown to converge, with hardly any advantage to using 20 size bins.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Directed energy deposition of Haynes 282 nickel superalloy

Laser powder directed energy deposition was employed to fabricate Haynes® 282 Ni-based superalloy for high temperature creep testing. Material was heat treated using a single-step aging heat treatment of 800 °C for 4 h. Microstructural analysis was conducted in the as-deposited, solution-annealed, and age-hardened conditions. γ′ precipitates were absent in the as-deposited and annealed condition but formed during aging with an average size of 48.5 ± 12 nm. γ’ denuded zones ranging in thickness from 73 to 469 nm were observed adjacent to an effectively continuous grain boundary carbide film that covered 72.5% of the measured boundary length. The heat-treated material contained a high-volume fraction of TiC carbides ranging in size from 38 to 457 nm. Electron backscatter diffraction showed partial recrystallization, with 77-83% recrystallized area and a heterogeneous grain-size distribution. Creep testing at 750 °C at 300, 320, and 350 MPa revealed significantly inferior performance compared to wrought material, with higher strain rates, earlier tertiary onset, and shorter rupture lives. Fractography shows that failure was dominated by intergranular rupture. Post rupture microstructural analysis results suggest that the creep behavior was primarily governed by the non-equilibrium interface network rather than the bulk γ/γ’ matrix. In conclusion, the findings indicate that achieving wrought-like creep performance necessitates substantial improvements in the additive process, specifically focusing on enhanced homogenization, full recrystallization, and precise control over the morphology and distribution of carbides.

36 - MATERIALS SCIENCE↗
DOE OSTI2023

H 2 generation by the 10 B(n,α) 7 Li reaction in high temperature water

H 2 produced in water from the 10 B(n,α) 7 Li fission reaction has been measured up to 300 °C. Thermal energy neutrons from the Rhode Island Nuclear Science Center's 2 MW reactor interact with boric acid-containing water in temperature-controlled high-pressure cells made from tubing of either titanium or zirconium alloy. After exposure for a minimum of 1 h, the solution sample is extracted and sparged with argon. The H 2 entrained by the sparging gas is sampled with a small mass spectrometer. A small amount of sodium is included in the boric acid solution so that after sparging, samples can be collected for 24 Na activation measurements in a gamma spectrometer to determine the neutron exposure and thus the total energy deposited in solution. The G-value (μmol/J) for H 2 production is obtained for water at a pressure of 25 MPa, over a temperature range from 20 °C to 300 °C. The weak temperature dependence of this yield between 150 °C and 200 °C demonstrates that the bimolecular reaction of pairs of e$^{–}_{aq}$ is a very minor source of H 2 in high LET tracks.

10B↗
DOE OSTI2025

Scalable Solution-Processed Electrolyte Membranes with Optimized Microstructure for High-Performance Protonic Ceramic Electrochemical Cells

Proton-conducting electrochemical cells (PCECs) are promising for efficient hydrogen production, but achieving dense, uniform, thin electrolyte layers remains a key challenge, particularly for scalable fabrication. Here, we present a solution-processed deposition approach with a mechanistically optimized slurry for uniform electrolyte formation. By tailoring particle size distribution, solid loading, and solvent/additive balance, we regulated wetting behavior and evaporation kinetics of the electrolyte slurry to promote homogeneous electrolyte particle packing. These features facilitate tight grain boundary contact and early stage neck growth during sintering, eliminating residual porosity, and improving mechanical integrity. The resulting ∼15 μm thick electrolyte shows high density, strong electrode adhesion, and stable interfaces outperforming the previously reported spray-based fabricated electrolyte by about 31% at 600 °C in FC mode. Single cells deliver 0.962 W cm –2 at 600 °C in fuel cell mode and 1.31 A cm –2 at 1.3 V in electrolysis mode, maintaining robust performance over 100 h with negligible degradation (≤0.02% h –1 ) in each mode. Scale-up to 2.5 cm diameter substrates confirmed reproducible densification and geometric stability. This work demonstrates a cost-effective, scalable route where control over particle-fluid interactions and drying dynamics enables a superior electrolyte microstructure and high PCEC performance.

dense microstructure↗
DOE OSTI2021

Large-Scale Synthesis of Semiconducting Cu(In,Ga)Se2 Nanoparticles for Screen Printing Application

During the last few decades, the interest over chalcopyrite and related photovoltaics has been growing due the outstanding structural and electrical properties of the thin-film Cu(In,Ga)Se2 photoabsorber. More recently, thin film deposition through solution processing has gained increasing attention from the industry, due to the potential low-cost and high-throughput production. To this end, the elimination of the selenization procedure in the synthesis of Cu(In,Ga)Se2 nanoparticles with following dispersion into ink formulations for printing/coating deposition processes are of high relevance. However, most of the reported syntheses procedures give access to tetragonal chalcopyrite Cu(In,Ga)Se2 nanoparticles, whereas methods to obtain other structures are scarce. Herein, we report a large-scale synthesis of high-quality Cu(In,Ga)Se2 nanoparticles with wurtzite hexagonal structure, with sizes of 10–70 nm, wide absorption in visible to near-infrared regions, and [Cu]/[In + Ga] ≈ 0.8 and [Ga]/[Ga + In] ≈ 0.3 metal ratios. The inclusion of the synthesized NPs into a water-based ink formulation for screen printing deposition results in thin films with homogenous thickness of ≈4.5 µm, paving the way towards environmentally friendly roll-to-roll production of photovoltaic systems.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Dynamic processes in transient phases during self-assembly of organic semiconductor thin films

Understanding and manipulating crystallization processes has been an important challenge for solution-processed organic thin films, both for fundamental studies and for fabricating thin films with near-intrinsic charge transport properties. We report an in situ X-ray scattering study of the crystallization of 2-decyl-7-phenyl-[1]benzothieno[3,2-b][1]benzothiophene (Ph-BTBT-C 10 ) during its deposition from solution. At temperatures modestly below the smectic-E/crystalline phase boundary, the crystallization goes through a transient liquid crystal state before reaching the final stable crystalline phase. Significant dynamics occur in the first few seconds of the transition, which are observed through fluctuations in the X-ray scattering intensity, and are correlated with the time interval that the transient thin film coexists with the evaporating solvent. The transition to the stable crystalline phase takes minutes or even hours under these conditions, which may be a result of the asymmetry of the molecule. Transient phases are of potential interest for applications, since they can act as a route to self-assembly of organic thin films. However, our observations show that the long-lived monolayer-stacked intermediate state does not act as a template for the bilayer-stacked crystalline phase. Rather, the grain structure is replaced through nucleation, where the nucleation free-energy barrier is related to a potential barrier that prevents molecules to flip their long axis by 180°.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Comparison of the Mechanical Properties of a Conjugated Polymer Deposited Using Spin Coating, Interfacial Spreading, Solution Shearing, and Spray Coating

The mechanical properties of π-conjugated (semiconducting) polymers are a key determinant of the stability and manufacturability of devices envisioned for applications in energy and healthcare. These properties—including modulus, extensibility, toughness, and strength—are influenced by the morphology of the solid film, which depends on the method of processing. To date, the majority of work done on the mechanical properties of semiconducting polymers has been performed on films deposited by spin coating, a process not amenable to the manufacturing of large-area films. Here, we compare the mechanical properties of thin films of regioregular poly(3-heptylthiophene) (P3HpT) produced by three scalable deposition processes—interfacial spreading, solution shearing, and spray coating—and spin coating (as a reference). Our results lead to four principal conclusions. (1) Spray-coated films have poor mechanical robustness due to defects and inhomogeneous thickness. (2) Sheared films show the highest modulus, strength, and toughness, likely resulting from a decrease in free volume. (3) Interfacially spread films show a lower modulus but greater fracture strain than spin-coated films. (4) The trends observed in the tensile behavior of films cast using different deposition processes held true for both P3HpT and poly(3-butylthiophene) (P3BT), an analogue with a higher glass transition temperature. Grazing incidence X-ray diffraction and ultraviolet–visible spectroscopy reveal many notable differences in the solid structures of P3HpT films generated by all four processes. Herein, while these morphological differences provide possible explanations for differences in the electronic properties (hole mobility), we find that the mechanical properties of the film are dominated by the free volume and surface topography. In field-effect transistors, spread films had mobilities more than 1 magnitude greater than any other films, likely due to a relatively high proportion of edge-on texturing and long coherence length in the crystalline domains. Overall, spread films offer the best combination of deformability and charge-transport properties.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Achieving High Thermoelectric Performance and Metallic Transport in Solvent-Sheared PEDOT:PSS

Polymer-based materials hold great potential for use in thermoelectric applications but are limited by their poor electrical properties. Through a combination of solution-shearing deposition and directionally applied solvent treatments, poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) thin films with metallic-like conductivities can be obtained with high power factors in excess of 800 µW m -1 K -2 . X-ray scattering and absorption data indicate that structural alignment of PEDOT chains and larger-sized domains are responsible for the enhanced electrical conductivity. Overall, it is expected that further enhancements to the power factor can be obtained through device geometry and postdeposition solvent shearing optimization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Advances in Carbon Electrode Integration for Stable and Efficient Perovskite Solar Cells and Modules

Carbon-electrode-based perovskite solar cells (C-PSCs) have emerged as a cost-effective and scalable alternative to noble-metal-based PSCs, addressing critical challenges related to device stability, fabrication complexity, and commercialization potential. This review explores the recent progress in C-PSC development, focusing on the benefits of carbon electrodes (CEs), including their hydrophobicity, chemical inertness to halide corrosion, and compatibility with low-temperature cost-effective solution-based deposition methods. Despite relatively lower power conversion efficiencies (PCEs) than their metal (e.g., Au/Ag) counterparts, recent advances in carbon paste formulation, interfacial contact engineering, and work function modification have elevated C-PSC efficiencies above 22%. This review further examines strategies to enhance electrode conductivity, interfacial properties, and charge selectivity to further increase C-PSC performance. Progress in carbon-electrode-based perovskite solar modules (C-PSMs), particularly within mesoporous and planar architectures, is also analyzed, revealing significant developments in active area scaling and long-term stability. Notably, the limited research in inverted (PIN) C-PSCs is also highlighted as a compelling opportunity for innovation, given the architecture's inherent advantages in flexibility, tandem integration, and low-temperature processing. Collectively, these insights affirm the potential of C-PSCs and C-PSMs to deliver affordable, stable, and high-performance photovoltaics suitable for scalable deployment.

Carbon Electrodes↗
DOE OSTI2021

Techno-economic analysis of roll-to-roll production of perovskite modules using radiation thermal processes

Perovskite solar technology can produce economically viable photovoltaic devices due to low cost of materials and scalable manufacturing. Solution phase deposition of all active layers lends itself to roll-to-roll fabrication methods which are well-established and have production rates of several hundred square meters per minute. In this techno-economic analysis, the opportunity to scale at this production throughput is considered with manufacturing rates exceeding one gigawatt per year in a single plant. Intense pulsed light is used for the post deposition process to minimize costs associated with the footprint, equipment, and operation. The analysis is limited to the operation of a roll-to-roll manufacturing facility producing a perovskite solar film that can be incorporated into photovoltaic modules. Costs associated with materials, labor, and equipment are considered along with utilities determined from the fundamental engineering calculations. Furthermore, the results show that at very large-scale operations of several gigawatts, the costs to produce the solar films range between $0.04-$0.10 per watt.

14 SOLAR ENERGY↗