Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solid state battery”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

In Situ Li Seed Formation Enables Uniform Plating in Anode-Free Solid-State Batteries

Anode-free solid-state batteries (AFSSBs) are a promising route toward achieving high energy density. In these cells, the anode contains no pre-stored lithium (Li). Instead, all Li inventory originates from the cathode and is freshly deposited onto a bare current collector during charging. However, achieving uniform and defect-free Li plating on this bare current collector remains a major challenging, often resulting in low Li plating/stripping efficiency and rapid capacity decay. Here, for the first time, operando neutron imaging is employed to visualize Li plating/stripping behavior in an anode-free full cell with LiNi 0.82 Mn 0.07 Co 0.11 O 2 (NMC) as the cathode. Operando measurements reveal that complete stripping of Li leaves isolated Li residues on the current collector, which degrades interfacial contact between the current collector and solid-state electrolyte. To mitigate this interfacial issue and promote more uniform Li deposition, we implement a discharge cutoff voltage strategy that intentionally retains a thin residual Li layer after stripping. This thin Li layer, serving as an in situ–formed seed layer, not only enables more homogeneous subsequent Li plating but also improves interfacial contact. As a result, the anode-free cell with a controlled discharge voltage of 3.5 V exhibits excellent long-term cycling stability, maintaining a discharge capacity of 116 mAh g -1 with a retention rate of 83.4% and an average Coulombic efficiency of approximately 99.9% after 430 cycles at 0.25 C. In contrast, the cell with a conventional discharge cutoff voltage of 2.8 V exhibits rapid capacity decay, retaining only 59.7 mAh g -1 after 50 cycles with a capacity retention of 40.7%. This work offers a practical strategy to unlock the long-term viability of anode-free solid-state batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

All Solid State Batteries Enabled by Multifunctional Electrolyte Materials

Solid Power has teamed with University of California San Diego to develop a high energy, long life, low cost, and safe all-solid-state-battery (ASSB). The battery is enabled by a multifunctional solid state electrolyte (SSE). The project enables scalable production of large format solid state batteries required by the vehicle market and building domestic battery manufacturers as leaders in the global vehicle ASSB production. In the project, the multifunctional SSE materials have been developed and optimized with ionic conductivity ≥ 5 mS/cm and electrochemical stability 0 – 4.5V. SSE separator films have been coated by using a roll-to-roll process with thickness ≤ 40 µm. All-solid-state NMC-Li pouch cells containing the developed SSE have been assembled. A cycle life of > 750 at 100% DOD and 45 °C has been demonstrated in a full pouch cell.

25 ENERGY STORAGE↗
DOE OSTI2025

Solvent-Free Melt-Processed Cathode Mitigates Li Anode Instability in Polymer-Based Solid-State Batteries

Solvent-free manufacturing of battery components is a promising alternative to traditional slurry processing for reducing the cost and environmental impact. In this work, we used twin-screw melt extrusion to fabricate a polymer-based high voltage composite cathode. The melt-processed cathode is dense (near zero porosity) and thick (65 μm) and has high active material loading (80 wt %). The active particles are distributed uniformly throughout the melt-processed cathode, unlike the traditional slurry-cast cathode, which exhibits inhomogeneous particle distribution. In the melt-processed cathode, polymer and carbon form separate phases, whereas in the slurry-cast cathode they blend into a single phase. Due to these structural differences, the melt-processed cathode shows smooth charge–discharge profiles, while the slurry-cast cathode shows noisy charging and soft-shorting behavior. In conclusion, this work highlights that twin-screw extrusion as a scalable, solvent-free manufacturing method is advantageous in producing uniform cathodes, which mitigates anode instability.

25 ENERGY STORAGE↗
DOE OSTI2023

Solvent-free and low temperature synthesis of chalcogenide Na superionic conductors for solid-state batteries

Sodium chalcogenide ionic conductors are attractive candidates as solid electrolytes (SEs) in solid-state Na metal batteries. They show the advantages of high ionic conductivity of 10 –4 –10 –2 S cm –1 at room temperature and great chemical stability in air. However, simple, efficient, and scalable approaches for the synthesis of chalcogenide solid electrolytes (SEs) are required. In this work, we report a solvent-free mixing to form dry intermediate products, which are subjected to different treatments (electron-beam assisted method or low temperature heating (≤150 °C)) to produce pure phase of Na 3 SbS 4-y Se y (0 ≤ y < 2) chalcogenides. Heavy Se-doping in Na 3 SbS 4 results in the tetragonal-to-cubic phase transition as well as a significant change of Sb-S bonding in Raman spectra. Among all chalcogenide SEs, Na 3 SbS 3 Se showed the highest ionic conductivity of 3.75 × 10 –4 S cm –1 at room temperature, 47% higher than that of pristine Na 3 SbS 4 . Moreover, the Se-dopant also enhanced the electrochemical stability towards Na metal in solid-state batteries. The solid-state Na||FeS 2 battery with Na 3 SbS 3 Se SE displayed long-term cycling ability up to 1,000 cycles within the voltage window of 1.0–2.7 V and retained a specific capacity of 105 mAh g –1 after 600 cycles. As a result, this technique promotes the practical applications of chalcogenide SEs in solid-state batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

High‐Entropy Lithium Argyrodite Solid Electrolytes Enabling Stable All‐Solid‐State Batteries

Abstract Superionic solid electrolytes (SEs) are essential for bulk‐type solid‐state battery (SSB) applications. Multicomponent SEs are recently attracting attention for their favorable charge‐transport properties, however a thorough understanding of how configurational entropy (ΔS conf ) affects ionic conductivity is lacking. Here, we successfully synthesized a series of halogen‐rich lithium argyrodites with the general formula Li 5.5 PS 4.5 Cl x Br 1.5‐x (0≤x≤1.5). Using neutron powder diffraction and 31 P magic‐angle spinning nuclear magnetic resonance spectroscopy, the S 2− /Cl − /Br − occupancy on the anion sublattice was quantitatively analyzed. We show that disorder positively affects Li‐ion dynamics, leading to a room‐temperature ionic conductivity of 22.7 mS cm −1 (9.6 mS cm −1 in cold‐pressed state) for Li 5.5 PS 4.5 Cl 0.8 Br 0.7 (ΔS conf =1.98R). To the best of our knowledge, this is the first experimental evidence that configurational entropy of the anion sublattice correlates with ion mobility. Our results indicate the possibility of improving ionic conductivity in ceramic ion conductors by tailoring the degree of compositional complexity. Moreover, the Li 5.5 PS 4.5 Cl 0.8 Br 0.7 SE allowed for stable cycling of single‐crystal LiNi 0.9 Co 0.06 Mn 0.04 O 2 (s‐NCM90) composite cathodes in SSB cells, emphasizing that dual‐substituted lithium argyrodites hold great promise in enabling high‐performance electrochemical energy storage.

Chemistry↗
DOE OSTI2021

Amphipathic Binder Integrating Ultrathin and Highly Ion-Conductive Sulfide Membrane for Cell-Level High-Energy-Density All-Solid-State Batteries

Current sulfide solid-state electrolyte (SE) membranes utilized in all-solid-state lithium batteries (ASLBs) have a high thickness (0.5–1.0 mm) and low ion conductance (<25 mS), which limit the cell-level energy and power densities. Therefore, based on ethyl cellulose's unique amphipathic molecular structure, superior thermal stability, and excellent binding capability, this work fabricates a freestanding SE membrane with an ultralow thickness of 47 µm. With ethyl cellulose as an effective disperser and a binder, the Li 6 PS 5 Cl is uniformly dispersed in toluene and possesses superior film formability. In addition, an ultralow areal resistance of 4.32 Ω cm -2 and a remarkable ion conductance of 291 mS (one order higher than the state-of-the-art sulfide SE membrane) are achieved. The ASLBs assembled with this SE membrane deliver cell-level high gravimetric and volumetric energy densities of 175 Wh kg -1 and 675 Wh L -1 , individually.

25 ENERGY STORAGE↗
DOE OSTI2023

Structural and electrochemical evolution of alloy interfacial layers in anode-free solid-state batteries

“Anode-free” solid-state batteries feature high energy density since there is no anode active material. Although the beneficial effects of interfacial layers at the anode-solid electrolyte interface have been demonstrated, the mechanisms through which they influence lithium plating/stripping are unclear. Here, in this study, we reveal the evolution of 100-nm silver and gold interfacial layers during lithium plating/stripping using electrochemical methods, electron microscopy, X-ray microcomputed tomography, and modeling. The alloy layers improve Coulombic efficiency and resistance to short circuiting, even though the alloys form solute regions or particulates that detach from the current collector during plating. In situ electrochemical impedance spectroscopy shows that the alloys return to the interface and mitigate contact loss at the end of stripping, avoiding a critical vulnerability of anode-free cells. Contact retention is driven by even Li thickness that promotes spatially uniform stripping, as well as local alloy delithiation in response to current concentrations that homogenizes current and diminishes voiding.

25 ENERGY STORAGE↗
DOE OSTI2024

Advances in solid-state batteries: Materials, interfaces, characterizations, and devices

Solid-state batteries with features of high potential for high energy density and improved safety have gained considerable attention and witnessed fast growing interests in the past decade. Significant progress and numerous efforts have been made on materials discovery, interface characterizations, and device fabrication. Further, this issue of MRS Bulletin focuses on the current state of the art of solid-state batteries with the most important topics related to the interface issues, advanced characterizations, and electrode chemistries, aiming to provide a comprehensive perspective for the interface and characterization challenges for high-performance solid-state battery devices.

25 ENERGY STORAGE↗
DOE OSTI2025

Promising performance of sulfide catholytes compared to halide alternatives in NMC811 cathodes for sheet-type sulfide solid-state batteries

Sulfide-based solid-state batteries (SSBs) show promise in achieving energy densities over 350 Wh/kg, yet challenges persist with their incorporation of high-voltage, nickel-rich layered oxide cathodes, such as LiNi₀.₈Mn₀.₁Co₀.₁O₂ (NMC811), due to the poor oxidation stability of sulfide solid-state electrolytes (SSEs) like Li₆PS₅Cl (LPSCl). Although halide SSEs such as Li₃InCl₆ (LIC) and Li₃YCl₆ (LYC) have previously shown promise in stabilizing high-voltage NMC cathodes, our research reveals that sulfide SSE catholytes, particularly when combined with surface-coated NMC cathodes, deliver superior performance. Here, this investigation assesses the cycling stability of various catholytes—LPSCl, LIC, Li₁₀GeP₂S₁₂ (LGPS), combined LIC-LPSCl, and LYC-LPSCl—in SSBs with LiNbO₃-coated NMC811 cathodes against sheet-type LPSCl separators. Findings indicate that while LGPS-based cathodes maintain higher capacity retention, they yield lower deliverable capacity, and LIC cathodes experience significant electrochemical degradation. Importantly, our results underscore that sulfide SSE catholytes, in conjunction with LiNbO₃-coated cathodes, optimize the cathode-electrolyte interphase (CEI), enhancing both kinetics and mass transport. These insights provide a strategic direction for optimizing catholyte composition in the development of sheet-type sulfide-based SSBs.

Catholyte↗
DOE OSTI2021

Spatially Resolved Potential and Li-Ion Distributions Reveal Performance-Limiting Regions in Solid-State Batteries

The performance of solid-state electrochemical systems is intimately tied to the potential and lithium distributions across electrolyte–electrode junctions that give rise to interface impedance. Here, we combine two operando methods, Kelvin probe force microscopy (KPFM) and neutron depth profiling (NDP), to identify the rate-limiting interface in operating Si-LiPON-LiCoO 2 solid-state batteries by mapping the contact potential difference (CPD) and the corresponding Li distributions. The contributions from ions, electrons, and interfaces are deconvolved by correlating the CPD profiles with Li-concentration profiles and by comparisons with first-principles-informed modeling. Furthermore, we find that the largest potential drop and variation in the Li concentration occur at the anode–electrolyte interface, with a smaller drop at the cathode–electrolyte interface and a shallow gradient within the bulk electrolyte. Correlating these results with electrochemical impedance spectroscopy following battery cycling at low and high rates confirms a long-standing conjecture linking large potential drops with a rate-limiting interfacial process.

25 ENERGY STORAGE↗
DOE OSTI2024

Fast Kinetics Design for Solid‐State Battery Device

Abstract Fast kinetics of solid‐state batteries at the device level is not adequately explored to achieve fast charging and discharging. In this work, a leap forward is achieved for fast kinetics in full cells with high cathode loading and areal capacity. This kinetic improvement is achieved by designing a hierarchical structure of electrode composites. In the cathode, the authors’ design enables high areal capacities above 3 mAh cm −2 to be stably cycled at high current densities of ≈13–40 mA cm −2 , yielding a C‐rate from 5 to 10 C. In the anode, the authors’ design breaks the common rule of the negative correlation between critical C‐rate and the discharge voltage that is observed in most other anodes. The overall design enables the fast cycling of such batteries for over 4000 cycles at room temperature and 5 C charge‐rate. The design principles unveiled by this work help to understand critical kinetic processes in battery devices that limit the fast cycling at high cathode loading and speed up the design of high‐performance solid‐state batteries.

Wang, Yichao↗
DOE OSTI2023

Solid-state batteries: The critical role of mechanics

Solid-state batteries with lithium metal anodes have the potential for higher energy density, longer lifetime, wider operating temperature, and increased safety. Although the bulk of the research has focused on improving transport kinetics and electrochemical stability of the materials and interfaces, there are also critical challenges that require investigation of the mechanics of materials. In batteries with solid-solid interfaces, mechanical contacts, and the development of stresses during operation of the solid-state batteries, become as critical as the electrochemical stability to keep steady charge transfer at these interfaces. In conclusion, this review will focus on stress and strain that result from normal and extended battery cycling and the associated mechanisms for stress relief, some of which lead to failure of these batteries.

25 ENERGY STORAGE↗
DOE OSTI2026

Conformal hetero-electrolyte interface between soft oxyhalides and garnet enables low-pressure lithium-reservoir-free solid-state batteries

The operation of solid-state batteries with a lithium metal anode and a high voltage cathode requires solid electrolytes (SEs) that are chemically stable with lithium, have a wide electrochemical window, and accommodate volume changes in the electrodes. Unfortunately, no SE has exhibited satisfactory mechanical and electrochemical properties that fit these requirements to date. Dual solid electrolyte systems that use a different SE for the anolyte and catholyte present a viable solution. Here, we focus on oxyhalide SEs that demonstrate superior ionic conductivity and cathode compatibility, where their lithium metal reactivity and poor reduction stability can be resolved using a lithium garnet (Li 6.5 La 3 Zr 1.5 Ta 0.5 O 12 , LLZTO) separator. Nonetheless, this imposes a new hetero-electrolyte (H-E) interface at the anolyte|catholyte contact that defines the ion transport across the boundary. We report its promising properties, which are deconvoluted from the electrical measurements of bilayer symmetric cells, for three representative oxyhalide catholytes, LiNbOCl 4 , LiTaOCl 4 , and Li 3 Al 3 O 2 Cl 8 . Pressure-dependent measurements reveal that the relative softness of the oxyhalides (hardness ≤0.4 GPa) enables H-E resistances lower than 150 Ω cm 2 at 2–3 MPa. Mesoscale modelling reveals that the transfer-active contact area of oxyhalides with LLZTO is about 2–3-fold higher than that of argyrodite, Li 6 PS 5 Cl. The low H-E resistance of the LiNbOCl 4 |Li 6.5 La 3 Zr 1.5 Ta 0.5 O 12 dual electrolyte enables the cycling of a Li|LiNi 0.82 Mn 0.07 Co 0.11 O 2 full cell with a high discharge capacity (200 mA h g −1 ) at 60 °C and ∼7 MPa. Importantly, we demonstrate a Li-reservoir-free full cell with high Coulombic efficiency (>99.5%) and capacity at 1 MPa using this approach coupled with a garnet-silver interlayer.

Palmer, Max [University of California, Santa Barba↗
DOE OSTI2023

The role of ionic liquids in resolving the interfacial chemistry for (quasi-) solid-state batteries

Interfacial issues impede the advancement of current solid state battery technology; thus, interface engineering approaches are necessary to enable solid-state configuration. The advantage of solid-state cells stems from their low flammability and high electrochemical stability. Ionic liquids are viscous and nonflammable compounds that possess the requisite physical properties while optimizing the interface between solid electrodes and solid electrolytes, accelerating interfacial ion transport and enabling the fabrication of engineered interphases via the supply of robust chemical building blocks. In conclusion, this review summarizes the roles of ionic liquids in solid-state batteries focusing on the interface, with insights into their functionality as well as highlighting their applicability in the next generation battery systems.

25 ENERGY STORAGE↗
DOE OSTI2026

Controlled lithium stripping enables a stable interface for long-cycling anode-free solid-state batteries

Anode-free solid-state batteries (AFSSBs) are a promising route toward achieving high energy density. In these cells, the anode contains no pre-stored lithium (Li). Instead, the entire Li inventory originates from the cathode and is freshly deposited onto a bare current collector during charging. However, achieving uniform and defect-free Li plating on this bare current collector remains a major challenge, often resulting in low Li plating/stripping efficiency and rapid capacity decay. Here, for the first time, operando neutron imaging is employed to visualize Li plating/stripping behavior in an anode-free full cell with LiNi0.82Mn0.07Co0.11O2 (NMC) as the cathode. Operando measurements reveal that complete stripping of Li leaves isolated Li residues on the current collector, which degrades the interfacial contact between the current collector and the solid-state electrolyte. To mitigate this interfacial issue and promote more uniform Li deposition, we implement a discharge-cutoff-voltage strategy that intentionally retains a thin residual Li layer after stripping. This preserved Li-containing interfacial reservoir not only improves interfacial contact but also serves as an in situ formed seed layer that enables more homogeneous subsequent Li plating. As a result, the optimized anode-free cell with limited stripping depth exhibits excellent long-term cycling stability, maintaining a discharge capacity of 112.1 mAh g−1 with a capacity retention of 80.6% and an average coulombic efficiency of approximately 99.9% after 500 cycles at 0.25 C. In contrast, the cell with a conventional discharge cutoff voltage of 2.8 V exhibits rapid capacity decay, retaining only 59.7 mAh g−1 after 50 cycles with a capacity retention of 40.7%. This work demonstrates that limiting deep stripping to preserve a thin Li-containing interfacial layer can effectively improve the cycling stability of sulfide-based AFSSBs.

Wang, Jiwei [Northeastern University, Boston]↗
DOE OSTI2023

Impact of fabrication methods on binder distribution and charge transport in composite cathodes of all-solid-state batteries

Abstract The manufacturing process of all-solid-state batteries necessitates the use of polymer binders. However, these binders, being ionic insulators by nature, can adversely affect charge transport within composite cathodes, thereby impacting the rate performance of the batteries. In this work, we aim to investigate the impact of fabrication methods, specifically the solvent-free dry process versus the slurry-cast wet process, on binder distribution and charge transport in composite cathodes of solid-state batteries. In the dry process, the binder forms a fibrous network, while the wet process results in binder coverage on the surface of cathode active materials. The difference in microstructure leads to a notable 20-fold increase in ionic conductivity in the dry-processed cathode. Consequently, the cells processed via the dry method exhibit higher capacity retention of 89% and 83% at C/3 and C/2 rates, respectively, in comparison to 68% and 58% for the wet-processed cells at the same rate. These findings provide valuable insights into the influence of fabrication methods on binder distribution and charge transport, contributing to a better understanding of the binder’s role in manufacturing of all-solid-state batteries.

Emley, Benjamin↗
DOE OSTI2025

A Diffuse-Interface Model for Predicting the Evolution of Metallic Negative Electrodes and Interfacial Voids in Solid-State Batteries with Homogeneous and Polycrystalline Solid Electrolyte Separators

Here, this paper presents a novel diffuse-interface electrochemical model that simultaneously simulates the evolution of the metallic negative electrode and interfacial voids during the stripping and plating processes in solid-state batteries. The utility and validity of this model are demonstrated for the first time on a cell with a sodium (Na) negative electrode and a Na-β″-alumina ceramic solid electrolyte (SE) separator. Three examples are simulated. First, stripping and plating with a perfect electrode/electrolyte interface; second, stripping and plating with a single interfacial void at the electrode/electrolyte interface; third, stripping with multiple interfacial voids. Both homogeneous and polycrystalline SEs with low and high-conductivity grain boundaries (GBs) are considered for all three examples. Heterogeneous GB conductivity marginally impacts the thickness of the Na electrode in cases with a perfect electrode/electrolyte interface. Moreover, it results in local changes to void growth due to the interactions between the void edge and the GBs. The void growth rate is a linear function of the flux of Na atoms at the void edge, which in turn depends on the applied current density. We also show that the void coalescence rate increases with applied current density and can be marginally influenced by GB conductivity.

batteries↗