SEARCH · Engineering Papers

Results for “slots”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

NASA NTRSDate not supplied

Transonic Cruise Slotted Wing Design for Commercial Transport Aircraft using CDISC

A knowledge-based aerodynamic design method, CDISC, has been extended to enable the computational design of transonic cruise slotted wings for commercial transport aircraft. The cruise slotted wing is a multielement wing concept with a forward main element and an aft flap element, separated to form an intermediate slot. This slot favorably redirects airflow from the main element lower surface toward the low-momentum, upper-surface boundary layer of the flap. Relative to the supercritical wing, the cruise slotted wing enables greater aft loading that helps to reduce shock strength and transonic pressure drag. The cruise slotted wing may be considered a passive drag-reduction technology with potential fuel burn savings and increased vehicle range for next-generation aircraft. The current paper seeks to quantify the drag-saving benefits of cruise slotted wing technology in application to single-aisle commercial transport aircraft. A series of multielement design constraints were developed within CDISC for the design of a partial-span, cruise slotted wing for a Mach-0.8 variant of the Common Research Model. To mitigate the skin-friction drag penalty associated with cruise slotted wings, the design features a flap with natural laminar flow over approximately 75% of the flap surface area. Cruise drag estimates from the NASA USM3D flow solver between a supercritical wing and the partial-span, cruise slotted wing design were within one drag count. Near-cruise, off-design analyses showed limited laminar flow sensitivity to angle of attack and a more gradual drag rise compared to a supercritical wing. Based on this demonstrated benefit, future work is motivated to design a cruise slotted wing with natural laminar flow on both wing elements to achieve a significant reduction in cruise drag while providing delayed drag divergence.

CDISC↗

NASA NTRS1941

Wind-tunnel investigation of an NACA 23012 airfoil with several arrangements of slotted flaps with extended lips

An investigation was made in the NACA 7- by 10-foot wind tunnel to determine the effect of slot-lip location on the aerodynamic section characteristics of an NACA 23012 airfoil with a 30-percent-chord slotted flap. Tests were made with slot lips located at 90 and 100 percent of the airfoil chord and with two different flap shapes. The results are compared with a slotted flap previously developed by the National advisory Committee for Aeronautics with a slot lip located at 83 percent of the airfoil chord. The extension of the slot lip to the rear increased the section lift and pitching-moment coefficients. Comparisons made on a basis of pitching moment for a given tail length show that the Fowler type flap, lip extended to trailing edge of the airfoil, has the greatest section lift coefficient. For moderate tail lengths, 2 to 3 chord lengths, there was only a slight difference between the previously developed slotted flap and the slotted flap with slot lip extended to 90 percent of the airfoil chord. Of the three flaps tested, the Fowler flap had the lowest drag coefficient at high lift coefficients. The extension of the lower surface at the leading edge of the slot had a negligible effect on the profile drag of the airfoil-flap arrangement with the flap deflected when the lip terminated at 90 percent of the airfoil chord.

WING FLAPS, SLOTTED - FULL-SPAN(30%-CHORD)↗

NASA NTRS1977

Meteorological radar facility (MRF) slot conductance investigations

A preliminary meteorological radar facility (MRF) array design was completed in support of the slot conductance measurement program. Three different slot measurement techniques were evaluated. The selection of the probe comparison measurement technique was selected as the principal experimental method with the impedance measurement technique chosen to measure a few higher conductance slots to be used as reference slots. The impedance of 43 slots in 0.9 x 0.4 inch standard waveguide and of 40 slots in 0.835 x 0.4 inch waveguide was measured. Also, impedance measurements were made of a few slots using image planes to simulate mutual coupling effects. The measured and theoretical conductance, susceptance, and radiation phase data are presented in graphic form as a function of slot displacement for constant slot length, and of slot length for constant slot displacement. It is concluded that the proposed MRF array design approach is a feasible one.

Ratkevich, A. E.↗

NASA NTRSDate not supplied

Cruise Slotted Wing Design with Natural Laminar Flow for Transonic Commercial Transport Aircraft

The present computational study investigates the aerodynamic design and analysis of cruise slotted wings with natural laminar flow for transonic transport aircraft. The cruise slotted wing is a multielement wing concept that features an intermediate slot to achieve greater aft loading relative to supercritical wings for the potential benefit of reduced shock strength and pressure drag. Transonic near-cruise, off-design assessments have also shown improved drag rise characteristics due to the ability of the slot to mitigate boundary layer separation on the aft flap component. However, due to the decreased Reynolds number of the flap, the cruise slotted wing has historically incurred a skin-friction drag penalty relative to a conventional supercritical wing. To offset this penalty, a cruise slotted wing with the forward main element and aft flap element shaped to achieve natural laminar flow is desired. Toward this effort, a knowledge-based aerodynamic design method, CDISC, has been leveraged to design a partial-span cruise slotted wing with natural laminar flow for a Mach-0.8 variant of the Common Research Model. Drag comparisons will be provided at cruise and near-cruise, off-design conditions relative to both fully turbulent and natural laminar flow conventional wing designs. It is anticipated that pairing natural laminar flow technology with the cruise slotted wing architecture will allow for cruise drag performance similar to conventional laminar flow wings with improved drag rise characteristics and more limited laminar-flow sensitivity at off-design conditions. Preliminary results for a cruise slotted wing with laminar flow on the outboard wing section only have shown a 10-ct cruise drag reduction relative to a conventional supercritical wing, but a 8-ct penalty relative to the conventional NLF wing. The final paper will include results for a cruise slotted wing design with laminar flow on both the inboard and outboard wing sections.

CFD↗

NASA NTRSDate not supplied

Cruise Slotted Wing Design with Natural Laminar Flow for Transonic Commercial Transport Aircraft

Natural Laminar Flow↗

NASA NTRS1976

Effect of geometry modifications on effectiveness of slot injection in hypersonic flow

The study presents wind-tunnel measurements of surface static pressures, equilibrium temperatures, and skin friction downstream of tangential slot injection into a thick turbulent hypersonic boundary layer from two modified slot configurations. The data are compared with results obtained for baseline configurations reported by Cary and Hefner (1970, 1972) to determine whether simple modifications to the slot configuration can produce improved cooling effectiveness and skin friction reduction. The baseline slot configurations are simply modified by thickening the slot lip and by elevating the location of the slot exit above the flat plate. Although the results indicate that simple modifications of the baseline slot configurations can enhance the skin friction reductions obtained with tangential slot injection, slot base drag estimates show that neither of the modifications will lessen the impact of the systems penalties for collecting, ducting, and injecting the slot air.

Hefner, J. N.↗

NASA NTRS1973

An experimental study of slot injection into a supersonic stream

An experimental investigation of two-dimensional tangential-slot injection into a turbulent boundary layer at a freestream Mach number of 2.4 has been conducted. Nearly adiabatic surface temperatures were maintained during all tests. Static and pitot pressure profiles at four stations downstream of the slot were obtained. Skin friction was measured at the last three stations with a self-nulling balance. Schlieren photographs of the flow field were also obtained. Most of the data were obtained with slot Mach numbers of 0.31 and 0.66 corresponding to slot pressure less than and equal to stream static pressure, respectively. For the latter matched-pressure case, tangential slot injection reduced the surface shear at the three measuring stations by about 60 to 20 percent for increasing downstream distances from the slot of 12 to 28 slot heights. However, for the other case where slot pressure was less than stream static pressure, the effect of injection was to increase the shear by about 90 percent at the last downstream station of 28 slot heights. This increase in shear is attributed to the rapid acceleration of the low speed injectant stream by the high speed main stream and the increasing pressure through the recompression zone which is absent for the matched pressure case.

Kenworthy, M.↗

NASA NTRS1976

Skin friction reduction by slot injection at Mach 0.8

Surface skin friction, boundary layer profiles and turbulent intensity due to axially symmetric tangential slot injection into a transonic boundary layer were measured. Effects of slot height, multiple slot injection, and injection mass flow rate on the surface skin friction downstream of the the slot have been investigated. Surface skin friction was a function of the injection mass flow rate for x/s 40. Large normal pressure gradient and relatively large turbulent intensity were found near the slot with small injection mass flow rate; the region the high turbulent intensity moved downstream with increasing injection mass flow rate. The results with two slot injections indicated that the distance between slots should be less than 30 slot heights in order to achieve some benefits from the first slot. Of significant importance in the present investigation is that the skin friction reduction obtained at transonic speed is of the same order as obtained in the hypersonic regime. Additional work is required in order to formulate a correlation between the turbulent intensity and the injection mass flow rate that may be used in future analysis.

Zakkay, V.↗

NASA NTRS1985

The effect of slots on the buckling and postbuckling behavior of laminated plates

An experimental study was conducted to evaluate the effect of lateral slots on the buckling response, the postbuckling response, and the failure characteristics of flat rectangular graphite-epoxy plates loaded in compression. The slots did not significantly affect the prebuckling and buckling behavior of the plates. The slots caused local changes in the strain distribution and out-of-plane deformations near the slot. Failure loads and modes were strongly affected by slot location. Centrally located slots did not affect the failure loads or failure modes of the plates. Slots located close to an unloaded edge of a plate reduced the postbuckling strength of the plate and affected the failure mode. For one slightly offset slot location, interaction of out-of-plane deformations with the slot tip was observed to affect the failure mode significantly without affecting the failure load.

Gurdal, Z.↗

NASA NTRS1990

Investigation of transonic flow over segmented slotted wind tunnel wall with mass transfer

The flowfield on a segmented multi-slotted wind tunnel wall was studied at transonic speeds by measurements in and near the wall layer using five port cone probes. The slotted wall flowfield was observed to be three-dimensional in nature for a relatively significant distance above the slot. The boundary layer characteristics measured on the single slotted wall were found to be very sensitive to the applied suction through the slot. The perturbation in the velocity components generated due to the flow through the slot decay rapidly in the transverse direction. A vortex-like flow existed on the single slotted wall for natural ventilation but diminished with increased suction flow rate. For flow on a segmented multi-slotted wall, the normal velocity component changes were found to be maximum for measurement points located between the segmented slots atop the active chamber. The lateral influence due to applied suction and blowing, through a compartment, exceeded only slightly that in the downstream direction. Limited upstream influence was observed. Influence coefficients were determined from the data in the least-square sense for blowing and suction applied through one and two compartments. This was found to be an adequate determination of the influence coefficients for the range of mass flows considered.

Bhat, M. K.↗

NASA NTRS1994

Wind Tunnel Results of Pneumatic Forebody Vortex Control Using Rectangular Slots a Chined Forebody

A subsonic wind tunnel investigation of pneumatic vortex flow control on a chined forebody using slots was accomplished at a dynamic pressure of 50 psf resulting in a R(n)/ft of 1.3 x 10(exp 6). Data were acquired from angles of attack ranging from -4deg to +34deg at side slips of +0.4deg and +10.4deg. The test article used in this study was the 10% scale Fighter Lift and Control (FLAC) advanced diamond winged, vee-tailed fighter configuration. Three different slot blowing concepts were evaluated; outward, downward, and tangential with ail blowing accomplished asymmetrically. The results of three different mass flows (0.067, 0.13, and 0.26 lbm/s; C(sub mu)'s of less than or equal to 0.006, 0.011. and 0.022 respectively) were analyzed and reported. Test data are presented on the effects of mass flows, slot lengths and positions and blowing concepts on yawing moment and side force generation. Results from this study indicate that the outward and downward blowing slots developed yawing moment and side force increments in the direction opposite of the blowing side while the tangential blowing slots generated yawing moment and side force increments in the direction towards the blowing side. The outward and downward blowing slots typically produced positive pitching moment increments while the tangential blowing slots typically generated negative pitching moment increments. The slot blowing nearest the forebody apex was most effective at generating the largest increments and as the slot was moved aft or increased in length, its effectiveness at generating forces and moments diminished.

Alexander, Michael↗

NASA NTRS2011

Higher Order Mode Coupling in Feed Waveguide of a Planar Slot Array Antenna

A simple technique was developed to account for the higher order mode coupling between adjacent coupling slots in the feed waveguide of a planar slot array. The method uses an equation relating the slot impedance to the slot voltage and a reaction integral involving the equivalent magnetic current of the slot aperture and the magnetic field coupled from an adjacent slot. In the proposed method, one uses the Elliott s design technique to determine tilt angles and lengths of the coupling slots. The radiating slots are modeled as shunt admittances, and the coupling slots are modeled as series impedances.

Rengarajan, Sembiam↗

NASA NTRS2022

Properties of EUV Imaging Spectrometer (EIS) Slot Observations

The Extreme ultraviolet Imaging Spectrometer (EIS) on board the Hinode spacecraft has been operating since 2006, returning high-resolution data in the 170 – 212 and 246 – 292 Å wavelength regions. EIS has four slit options, with the narrow 1′′ and 2′′ slits used for spectroscopy and the wide 40′′ and 266′′ slits used for monochromatic imaging. In this article several properties of the 40′′ slit (or slot) are measured using the Fe XII 195.12 Å line, which is formed at 1.5 MK. The projected width of the slot on the detector shows a small variation along the slit with an average value of 40.949′′. The slot image is tilted on the detector and a quadratic formula is provided to describe the tilt. The tilt corresponds to four pixels on the detector and the slot centroid is offset mostly to the right (longer wavelengths) of the 1′′ slit by up to four pixels. Measurement of the intensity decrease at the edge of the slot leads to an estimate of the spatial resolution of the images in the x-direction. The resolution varies quadratically along the slot, with a minimum value of 2.9′′ close to the detector center. Intensities measured from the slot images are found to be on average 14% higher than those measured from the 1′′ slit at the same spatial location. Background subtraction is necessary to derive accurate intensities in quiet-Sun and coronal-hole regions. Prescriptions for deriving accurate slot intensities for different types of slot datasets are presented.

corona↗

NASA NTRS1933

The Effects of Slots and Flaps on Lateral Control of a Low-wing Monoplane as Determined in Flight

This paper presents the results of flight tests made to determine the effect of slots and flaps on the lateral control of a low-wing monoplane. Maximum angular accelerations in roll and yaw produced by sudden application of the ailerons and maximum accelerations in yaw produced by sudden application of the rudder during gliding flight were recorded for the following wing arrangements: (a) no auxiliary device; (b) full-span slots; (c) plain flaps; (d) flaps and full-span slots; (e) wing-tip slots. Rolling- and yawing-moment coefficients were derived from the accelerations. The full span slots and the flaps each had about the same influence on the aileron rolling moments. At values of the lift coefficient obtainable with the plain wing, the effect of these devices was negligible. At the higher lift coefficients obtainable with these devices, the rolling-moment coefficients increased slightly but, despite this increase, the aileron effectiveness progressively decreased with increasing lift coefficient, owing to the corresponding reduction in air speed. In the range covered by the tests, the effectiveness of the controls was appreciably reduced by the wing-tip slots. The adverse yawing moment of the ailerons experienced at the large lift coefficients obtained with the flaps was appreciably less than at similar lift coefficients obtained with either full-span or wing-tip slots. The yawing moments produced by the rudder were only slightly affected by the use of the auxiliary devices. The airplane was found to be laterally unstable with all combinations tested. Because of the angular velocities acquired in the time taken to deflect the ailerons the rolling moments recorded in flight were only about two thirds the values that would have been obtained with the wing restrained as in wind-tunnel tests.

WING SLOTS↗

NASA NTRS1972

Systematic two-dimensional cascade tests. Volume 3: Slotted double circular-arc hydrofoils

Performance parameters are presented for cascades of slotted double circular-arc hydrofoils tested over a range of systematically introduced variables in a rectilinear cascade tunnel which uses water as the test medium. Cascade configurations included various combinations of an inlet flow angle of 50, 60 and 70 deg; a cascade solidity of 0.75, 1.00 and 1.50; a hydrofoil camber angle of 20, 30, 40 and 45 deg; and angles of incidence between positive and negative stall. The slot was positioned at the 45 percent chord station and the slot exit width was 0.047-in. Tests were also performed with the slot positioned at the 35 percent chord station and with slot widths of 0.63 and 0.094-in. These data were correlated to indicate the effects of slot location and slot width on minimum loss incidence and deviation angles. In addition, a comparison is presented of the performance parameters for cascades of slotted and unslotted hydrofoils.

Columbo, R. M.↗

NASA NTRS1982

Wind tunnel tests of a zero length, slotted-lip engine air inlet for a fixed nacelle V/STOL aircraft

Zero length, slotted lip inlet performance and associated fan blade stresses were determined during model tests using a 20 inch diameter fan simulator in the NASA-LeRC 9 by 15 foot low speed wind tunnel. The model configuration variables consisted of inlet contraction ratio, slot width, circumferential extent of slot fillers, and length of a constant area section between the inlet throat and fan face. The inlet performance was dependent on slot gap width and relatively independent of inlet throat/fan face spacer length and slot flow blockage created by 90 degree slot fillers. Optimum performance was obtained at a slot gap width of 0.36 inch. The zero length, slotted lip inlet satisfied all critical low speed inlet operating requirements for fixed horizontal nacelles subsonic V/STOL aircraft.

Woollett, R. R.↗

NASA NTRS1984

A slotted test section numerical model for interference assessment

A numerical model of a slotted wind tunnel test section, intended for use with sparsely measured wall pressures in a wall interference assessment procedure, is described. The numerical model includes a discrete finite length wall slot representation and accounts for the nonlinear effects of the dynamic pressure of the slot outflow jet and of the low energy of slot inflow air. By using th numerical model in a wall interference prediction mode, it is demonstrated that accounting for slot discreteness is important in interpreting wall pressures measured between slots, and that accounting for finite slot length and nonlinear effects in the slot boundary condition can yield significant departures from the wall interference predicted using the classical linear homogeneous infinite-length wall representation.

Kemp, W. B., Jr.↗

NASA NTRS1986

Radiation pattern analysis of the tapered slot antenna, appendix 1

A theoretical model for the tapered slot antenna is presented. The model is valid for any smooth taper of the slot. The problem is solved by modeling the slot electric field and using the half plane Green's function to compute the far fields. The aperture field is obtained by affecting a stepped approximation to the continuous taper and utilizing the uniform wide slot line data. The uniform wide slot line is solved by the spectral Galerkin's technique and closed form experssions are developed for the slot wave length and the slot characteristic impedance. Numerous comparisons with measurement are made to demonstrate the versatility of the model in treating an arbitrary slot taper.

Janaswamy, Ramakrishna↗