Research Achievements Review, volume II
Thermophysics, emissivity physics, thermal similitude, ultraviolet interactions with control surface materials, Pegasus satellite measurements, and infrared instrumentation
INFRARED INSTRUMENT↗
SEARCH · Engineering Papers
Results for “similitude”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Dynamic stability of space vehicles. Structural dynamics model testing
Dimensional analysis, and similitude and scaling laws for structural dynamics model testing of spacecraft dynamic stability
Wissmann, J. W.↗
Aspects of investigating STOL noise using large scale wind tunnel models
The applicability of the NASA Ames 40- by 80-ft wind tunnel for acoustic research on STOL concepts has been investigated. The acoustic characteristics of the wind tunnel test section has been studied with calibrated acoustic sources. Acoustic characteristics of several large-scale STOL models have been studied both in the free-field and wind tunnel acoustic environments. The results indicate that the acoustic characteristics of large-scale STOL models can be measured in the wind tunnel if the test section acoustic environment and model acoustic similitude are taken into consideration. The reverberant field of the test section must be determined with an acoustically similar noise source. Directional microphone and extrapolation of near-field data to far-field are some of the techniques being explored as possible solutions to the directivity loss in a reverberant field. The model sound pressure levels must be of sufficient magnitude to be discernable from the wind tunnel background noise.
Falarski, M. D.↗
Aspects of investigating STOL noise using large-scale wind-tunnel models.
The applicability of the NASA Ames 40- by 80-foot wind tunnel for acoustic research on STOL concepts has been investigated. The acoustic characteristics of the wind-tunnel test section have been studied with calibrated acoustic sources. Acoustic characteristics of several large-scale STOL models have been studied in both the free-field and wind-tunnel acoustic environments. The results of these studies indicate that the acoustic characteristics of large-scale STOL models can be measured in the wind tunnel if the test section acoustic environment and model acoustic similitude are taken into consideration. The reverberant field of the test section must be determined with an acoustically similar noise source. A directional microphone, a phased array of microphones, and extrapolation of near-field data to far-field are some of the techniques being explored as possible solutions to the directivity loss in a reverberant field. The model sound pressure levels must be of sufficient magnitude to be distinguishible from the wind-tunnel background noise.
Falarski, M. D.↗
Experimental evaluation of stresses in spherically hollow balls
An analysis was undertaken to evaluate stresses within spherically hollow ball bearings proportioned for 40, 50, and 60% mass reductions. Strain gage rosettes were used to determine principal strains and stresses in the steel ball models statically loaded in various orientations. Dimensionless results are reported for the balls under flate plate contact loads. Similitude considerations permit these results to be applied to calculate stresses in hollow ball bearings proportioned to these mass reductions.
Nypan, L. J.↗
Experimental evaluation of stresses in cylindrically hollow (drilled) balls
An experimental stress analysis was undertaken to evaluate stresses within cylindrically hollow (drilled) bearing balls proportioned for 40, 50, and 60 percent mass reductions. Strain gage rosettes were used to determine principal strains and stresses in the steel ball models statically loaded in various orientations. Results are reported for 127 mm OD balls under 44,500 N loads. Similitude considerations permit these results to be applied to calculate stresses in actual size drilled bearing balls proportioned to these mass reductions.
Nypan, L. J.↗
Craters on Earth, Moon, and Mars - Multivariate classification and mode of origin
Testing extraterrestrial craters and candidate terrestrial analogs for morphologic similitude is treated as a problem in numerical taxonomy. According to a principal-components solution and a cluster analysis, 402 representative craters on the Earth, the Moon, and Mars divide into two major classes of contrasting shapes and modes of origin. Craters of net accumulation of material (cratered lunar domes, Martian calderas, and all terrestrial volcanoes except maars and tuff rings) group apart from craters of excavation (terrestrial meteorite impact and experimental explosion craters, typical Martian craters, and all other lunar craters). Maars and tuff rings belong to neither group but are transitional. The classification criteria are four independent attributes of topographic geometry derived from seven descriptive variables by the principal-components transformation. Morphometric differences between crater bowl and raised rim constitute the strongest of the four components.
Pike, R. J.↗
Simulation of hypersonic scramjet exhaust
A plan and some preliminary analysis for the accurate simulation of pressure distributions on the afterbody/nozzle portions of a hypersonic scramjet vehicle are described. The objectives fulfilled were to establish the standards of similitude for a hydrogen/air scramjet exhaust interacting with a vehicle afterbody, determine an experimental technique for validation of the procedures that will be used in conventional wind tunnel facilities, suggest a program of experiments for proof of the concept, and explore any unresolved problems in the proposed simulation procedures. It is shown that true enthalpy, Reynolds number, and nearly exact chemistry can be provided in the exhaust flow for the flight regime from Mach 4 to 10 by a detonation tube simulation. A detailed discussion of the required similarity parameters leads to the conclusion that substitute gases can be used as the simulated exhaust gas in a wind tunnel to achieve the correct interaction forces and moments.
Oman, R. A.↗
Results of test 0A82 in the NASA/LRC 31 inch CFHT on an 0.010-scale model (32-0) of the space shuttle configuration 3 to determine RCS jet flow field interaction and to investigate RT real gas effects
Tests were conducted in the NASA Langley Research Center 31-inch Continuous Flow Hypersonic Wind Tunnel to determine RCS jet interaction effects on hypersonic aerodynamic characteristics and to investigate RT (gas constant times temperature) scaling effects on the RCS similitude. The model was an 0.010-scale replica of the Space Shuttle Orbiter Configuration 3. Hypersonic aerodynamic data were obtained from tests at Mach 10.3 and dynamic pressures of 200, 150, 125, and 100 psf. The RCS modes of pitch, yaw, and roll at free flight dynamic pressure simulation of 20 psf were investigated.
Thornton, D. E.↗
Stresses in a webbed ball
An experimental stress analysis was undertaken to evaluate stresses within cylindrically hollow reinforced webbed bearing balls proportioned for a 50 percent mass reduction. Strain gage rosettes were used to determine principal strains and stresses in the steel ball models, which were statically loaded in various orientations. Results are reported for 127 mm (5 in.) outside diameter balls under 44,500 N (10,000 lb) loads. Similitude considerations permit these results to be applied to calculations of stresses in actual size drilled bearing balls proportioned to these mass reductions.
Nypan, L. J.↗
The effect of vertical distortion in the modeling of sedimentation phenomena - Martian crater wake streaks
Theoretical mass flow rate and the particle trajectory equations of motion of granular material in saltation are used to correlate experimental data for the rate of erosion in the wake regions of wind-tunnel-model Martian craters. Vertical geometric distortion is inherent in the simulation because of the equivalent roughness height characteristic of a turbulent boundary layer, which is affected by material in saltation. It is thus necessary to distort topographic model geometry in the vertical direction. A systematic similitude which is based on erosion rate and equivalent roughness in saltation is shown to correlate time-dependent model data as long as the model Reynolds number is higher than a critical value.
Iversen, J. D.↗
Matters of simulation of the semicircular canal system
A scale model of the human semicircular canal system was developed based on the theory of dynamic similitude. This enlarged model makes it convenient to conduct tests on the vestibular processes and dynamics in the semicircular canals. Tests revealed hydromechanical interaction between canals, with asymmetry of the conditions of movement of the endolymph in the canals in opposite directions. A type of vestibular reactions, occurring with angular oscillations of the head, was predicted and demonstrated using this model and human test subjects.
Gurfinkel, V. S.↗
A study of the Tyrone-Mount Union lineament by remote sensing techniques and field methods
The author has identified the following significant results. This study has shown that subtle variations in fold axes, fold form, and stratigraphic thickness can be delineated. Many of the conclusions were based on extrapolation in similitude to different scales. A conceptual model was derived for the Tyrone-Mount Union lineament. In this model, the lineament the morphological expression of a zone of fracture concentrations which penetrated basement rocks and may have acted as a curtain to regional stresses or as a domain boundary between uncoupled adjacent crustal blocks.
Gold, D. P.↗
Icing testing in the large Modane wind-tunnel on full-scale and reduced scale models
Icing tests on full scale models of parts of aircraft (wings, tailplanes, radome) equipped with actual de-icing systems were carried out in the large Modane wind tunnel of ONERA. For studying icing on the Concorde, it was necessary to use a 1/6 scale half model. The equations governing the relevant parameter ratios to obtain reasonably good similitude water catching and ice accretion are recalled. Despite the inherent limitations of this particular kind of testing, i.e., the impossibility of duplicating both the Mach and Reynolds conditions for the main flow pattern, it is possible to obtain on a reduced scale model a reasonably good representation of icing cloud catching and of the shape of resulting ice accretion.
Charpin, F.↗
NASTRAN thermal analyzer in a unified finite-element treatment of thermo-structural analyses
The NASTRAN thermal analyzer (NTA) which performs large-scale unified thermo-structural analyses with the NASTRAN (NASA structural analysis) computer program is described. The mathematical similitude between these two distinct disciplines of thermal and structure is examined. It serves as the theoretical basis upon which the implementation of the thermal capability in NASTRAN was accomplished. The program structure, the functional flow, the solution algorithms, the organization of an input data deck and the solution capabilities of NTA are summarized. Emphasis is placed on the interface of the unified approach in thermo-structural analyses where stresses, deflections, vibrations and bucklings induced by the effect of temperature change are of concern. Attentions are also directed to the preprocessor and post processors. As a specially designed preprocessor, the VIEW program is capable of generating exchange factors which can be output, at user's option, in formats compatible with that required by NTA. Two post processors that serve specific objectives are included. They are the thermal variance analysis and the graphical displaying capability of temperatures in color or black and white.
Lee, H. P.↗
Scaling from Jupiter to pulsar and the acceleration of cosmic ray particles by pulsars
The total energy output per second from the 73 known pulsars is estimated. By following the principle of similitude (Rayleigh, 1915), an expression is derived for the energy generated by a rotating magnetized celestial body, and the dipole moment of the body is related linearly with its angular momentum. The scaling constant of the two equations combined is determined, and then checked by comparing the deduced masses of the 73 pulsars with the theoretical limits for neutron stars. By using the scaling constant and deduced pulsar masses, the rates of acceleration of high-energy particles by pulsars, thence the energy output from pulsars, can be estimated. Results show that the Crab pulsar outshines all the others combined.
Fan, Y. C.↗
Scaling from Jupiter to pulsars and mass spectrum of pulsars
Following the principle of similitude, the energy loss of Jupiter was scaled through the acceleration of high energy particles to that of Crab pulsar. The agreement suggests a classification scheme for all pulsars in which the pulsar angular velocity and its decrease with time are related to the pulsar moment of inertia divided by its radius and its mass is determined according to neutron star models. The mass spectrum of 194 pulsars is found to be approximately 1/sq m.
Fan, C. Y.↗
'Scaling' analysis of the ice accretion process on aircraft surfaces
A comprehensive set of scaling parameters is developed for the ice accretion process by analyzing the energy equations of the dynamic freezing zone and the already frozen ice layer, the continuity equation associated with supercooled liquid droplets entering into and impacting within the dynamic freezing zone, and energy equation of the ice layer. No initial arbitrary judgments are made regarding the relative magnitudes of each of the terms. The method of intrinsic reference variables in employed in order to develop the appropriate scaling parameters and their relative significance in rime icing conditions in an orderly process, rather than utilizing empiricism. The significance of these parameters is examined and the parameters are combined with scaling criteria related to droplet trajectory similitude.
Keshock, E. G.↗