Results for “real time simulations” — Page 3

NASA NTRS2007

Community Coordinated Modeling Center Support of Operations: Real-Time Simulations and V & V.

In support of Operations Community Coordinated Modeling Center (CCMC) performing validation and verification of space weather models. To identify suitable metrics the CCMC focus on parameters most useful to operations that CCMC resident models can provide. The real time simulations carried out at CCMC are an essential tool to test model performance and stability by using input conditions that may occur in nature at any time. Since 2001, the magnetospheric MHD model BATSRUS has been run in real time using ACE real time data. CCMC staff developed an experimental real-time system that controls uploading of the real-time ACE data, monitors continuous model execution, initiates automatic recovery procedure in case of data gaps or hardware failures, synchronizes BATSRUS and FRC runs, and periodically runs IDL based visualization software.

Kuznetsova, M.↗

NASA NTRS1974

Real-time simulation of the TF30-P-3 turbofan engine using a hybrid computer

A real-time, hybrid-computer simulation of the TF30-P-3 turbofan engine was developed. The simulation was primarily analog in nature but used the digital portion of the hybrid computer to perform bivariate function generation associated with the performance of the engine's rotating components. FORTRAN listings and analog patching diagrams are provided. The hybrid simulation was controlled by a digital computer programmed to simulate the engine's standard hydromechanical control. Both steady-state and dynamic data obtained from the digitally controlled engine simulation are presented. Hybrid simulation data are compared with data obtained from a digital simulation provided by the engine manufacturer. The comparisons indicate that the real-time hybrid simulation adequately matches the baseline digital simulation.

Szuch, J. R.↗

NASA NTRS1991

Propulsion modeling techniques and applications for the NASA Dryden X-30 real-time simulator

An overview is given of the flight planning activities to date in the current National Aero-Space Plane (NASP) program. The government flight-envelope expansion concept and other design flight operational assessments are discussed. The NASA Dryden NASP real-time simulator configuration is examined and hypersonic flight planning simulation propulsion modeling requirements are described. The major propulsion modeling techniques developed by the Edwards flight test team are outlined, and the application value of techniques for developmental hypersonic vehicles are discussed.

Hicks, John W.↗

NASA NTRS1983

ADA and multi-microprocessor real-time simulation

The selection of a high-order programming language for a real-time distributed network simulation is described. The additional problem of implementing a language on a possibly changing network is addressed. The recently designed language ADA (trademarked by DoD) was chosen since it provides the best model of the underlying application to be simulated.

Feyock, S.↗

NASA NTRS2003

Finite-Element Methods for Real-Time Simulation of Surgery

Two finite-element methods have been developed for mathematical modeling of the time-dependent behaviors of deformable objects and, more specifically, the mechanical responses of soft tissues and organs in contact with surgical tools. These methods may afford the computational efficiency needed to satisfy the requirement to obtain computational results in real time for simulating surgical procedures as described in Simulation System for Training in Laparoscopic Surgery (NPO-21192) on page 31 in this issue of NASA Tech Briefs. Simulation of the behavior of soft tissue in real time is a challenging problem because of the complexity of soft-tissue mechanics. The responses of soft tissues are characterized by nonlinearities and by spatial inhomogeneities and rate and time dependences of material properties. Finite-element methods seem promising for integrating these characteristics of tissues into computational models of organs, but they demand much central-processing-unit (CPU) time and memory, and the demand increases with the number of nodes and degrees of freedom in a given finite-element model. Hence, as finite-element models become more realistic, it becomes more difficult to compute solutions in real time. In both of the present methods, one uses approximate mathematical models trading some accuracy for computational efficiency and thereby increasing the feasibility of attaining real-time up36 NASA Tech Briefs, October 2003 date rates. The first of these methods is based on modal analysis. In this method, one reduces the number of differential equations by selecting only the most significant vibration modes of an object (typically, a suitable number of the lowest-frequency modes) for computing deformations of the object in response to applied forces.

Basdogan, Cagatay↗

NASA NTRS2015

Investigation of Asymmetric Thrust Detection with Demonstration in a Real-Time Simulation Testbed

The purpose of this effort is to develop, demonstrate, and evaluate three asymmetric thrust detection approaches to aid in the reduction of asymmetric thrust-induced aviation accidents. This paper presents the results from that effort and their evaluation in simulation studies, including those from a real-time flight simulation testbed. Asymmetric thrust is recognized as a contributing factor in several Propulsion System Malfunction plus Inappropriate Crew Response (PSM+ICR) aviation accidents. As an improvement over the state-of-the-art, providing annunciation of asymmetric thrust to alert the crew may hold safety benefits. For this, the reliable detection and confirmation of asymmetric thrust conditions is required. For this work, three asymmetric thrust detection methods are presented along with their results obtained through simulation studies. Representative asymmetric thrust conditions are modeled in simulation based on failure scenarios similar to those reported in aviation incident and accident descriptions. These simulated asymmetric thrust scenarios, combined with actual aircraft operational flight data, are then used to conduct a sensitivity study regarding the detection capabilities of the three methods. Additional evaluation results are presented based on pilot-in-the-loop simulation studies conducted in the NASA Glenn Research Center (GRC) flight simulation testbed. Data obtained from this flight simulation facility are used to further evaluate the effectiveness and accuracy of the asymmetric thrust detection approaches. Generally, the asymmetric thrust conditions are correctly detected and confirmed.

aircraft safety↗

NASA NTRS2015

Investigation of Asymmetric Thrust Detection with Demonstration in a Real-Time Simulation Testbed

The purpose of this effort is to develop, demonstrate, and evaluate three asymmetric thrust detection approaches to aid in the reduction of asymmetric thrust-induced aviation accidents. This paper presents the results from that effort and their evaluation in simulation studies, including those from a real-time flight simulation testbed. Asymmetric thrust is recognized as a contributing factor in several Propulsion System Malfunction plus Inappropriate Crew Response (PSM+ICR) aviation accidents. As an improvement over the state-of-the-art, providing annunciation of asymmetric thrust to alert the crew may hold safety benefits. For this, the reliable detection and confirmation of asymmetric thrust conditions is required. For this work, three asymmetric thrust detection methods are presented along with their results obtained through simulation studies. Representative asymmetric thrust conditions are modeled in simulation based on failure scenarios similar to those reported in aviation incident and accident descriptions. These simulated asymmetric thrust scenarios, combined with actual aircraft operational flight data, are then used to conduct a sensitivity study regarding the detection capabilities of the three methods. Additional evaluation results are presented based on pilot-in-the-loop simulation studies conducted in the NASA Glenn Research Center (GRC) flight simulation testbed. Data obtained from this flight simulation facility are used to further evaluate the effectiveness and accuracy of the asymmetric thrust detection approaches. Generally, the asymmetric thrust conditions are correctly detected and confirmed.

gas turbine engines↗

NASA NTRS2016

Investigation of Asymmetric Thrust Detection with Demonstration in a Real-Time Simulation Testbed

The purpose of this effort is to develop, demonstrate, and evaluate three asymmetric thrust detection approaches to aid in the reduction of asymmetric thrust-induced aviation accidents. This paper presents the results from that effort and their evaluation in simulation studies, including those from a real-time flight simulation testbed. Asymmetric thrust is recognized as a contributing factor in several Propulsion System Malfunction plus Inappropriate Crew Response (PSM+ICR) aviation accidents. As an improvement over the state-of-the-art, providing annunciation of asymmetric thrust to alert the crew may hold safety benefits. For this, the reliable detection and confirmation of asymmetric thrust conditions is required. For this work, three asymmetric thrust detection methods are presented along with their results obtained through simulation studies. Representative asymmetric thrust conditions are modeled in simulation based on failure scenarios similar to those reported in aviation incident and accident descriptions. These simulated asymmetric thrust scenarios, combined with actual aircraft operational flight data, are then used to conduct a sensitivity study regarding the detection capabilities of the three methods. Additional evaluation results are presented based on pilot-in-the-loop simulation studies conducted in the NASA Glenn Research Center (GRC) flight simulation testbed. Data obtained from this flight simulation facility are used to further evaluate the effectiveness and accuracy of the asymmetric thrust detection approaches. Generally, the asymmetric thrust conditions are correctly detected and confirmed.

propulsion system performance↗

NASA NTRS1988

Langley advanced real-time simulation (ARTS) system

A system of high-speed digital data networks was developed and installed to support real-time flight simulation at the NASA Langley Research Center. This system, unlike its predecessor, employs intelligence at each network node and uses distributed 10-V signal conversion equipment rather than centralized 100-V equipment. A network switch, which replaces an elaborate system of patch panels, allows the researcher to construct a customized network from the 25 available simulation sites by invoking a computer control statement. The intent of this paper is to provide a coherent functional description of the system. This development required many significant innovations to enhance performance and functionality such as the real-time clock, the network switch, and improvements to the CAMAC network to increase both distances to sites and data rates. The system has been successfully tested at a usable data rate of 24 M. The fiber optic lines allow distances of approximately 1.5 miles from switch to site. Unlike other local networks, CAMAC does not buffer data in blocks. Therefore, time delays in the network are kept below 10 microsec total. This system underwent months of testing and was put into full service in July 1987.

Crawford, Daniel J.↗

NASA NTRS1986

The new Langley Research Center advanced real-time simulation (ARTS) system

Based on a survey of current local area network technology with special attention paid to high bandwidth and very low transport delay requirements, NASA's Langley Research Center designed a new simulation subsystem using the computer automated measurement and control (CAMAC) network. This required significant modifications to the standard CAMAC system and development of a network switch, a clocking system, new conversion equipment, new consoles, supporting software, etc. This system is referred to as the advanced real-time simulation (ARTS) system. It is presently being built at LaRC. This paper provides a functional and physical description of the hardware and a functional description of the software. The requirements which drove the design are presented as well as present performance figures and status.

Crawford, D. J.↗

NASA NTRS2002

System engineering challenges of real-time simulation for Mars SmartLander entry, descent, and landing

The Jet Propulsion Laboratory (JPL) is developing a high-fidelity, real-time spacecraft simulator for Entry, Descent and Landing (EDL) on planetary and small bodies. This simulator, DSENDS (Dynamics Simulator for Entry, Descent and Surface landing), is an EDL-specific extension of the JPL Darts/Dshell multi-mission spacecraft dynamics and devices simulation toolkit which is in use by missions such as Cassini, Galileo, SIM, and Starlight.

Dshell EDL simulator↗

NASA NTRS2002

System engineering challenges of real-time simulation for Mars smart lander entry, descent and landing

Explore the source record for details and available documents.

Mars real-time issues DSENDS real-time simulator↗

NASA NTRS1993

Development and operation of a real-time simulation at the NASA Ames Vertical Motion Simulator

The Vertical Motion Simulator (VMS) facility at the NASA Ames Research Center combines the largest vertical motion capability in the world with a flexible real-time operating system allowing research to be conducted quickly and effectively. Due to the diverse nature of the aircraft simulated and the large number of simulations conducted annually, the challenge for the simulation engineer is to develop an accurate real-time simulation in a timely, efficient manner. The SimLab facility and the software tools necessary for an operating simulation will be discussed. Subsequent sections will describe the development process through operation of the simulation; this includes acceptance of the model, validation, integration and production phases.

Sweeney, Christopher↗

NASA NTRS1997

Real-Time Simulation

Coryphaeus Software, founded in 1989 by former NASA electronic engineer Steve Lakowske, creates real-time 3D software. Designer's Workbench, the company flagship product, is a modeling and simulation tool for the development of both static and dynamic 3D databases. Other products soon followed. Activation, specifically designed for game developers, allows developers to play and test the 3D games before they commit to a target platform. Game publishers can shorten development time and prove the "playability" of the title, maximizing their chances of introducing a smash hit. Another product, EasyT, lets users create massive, realistic representation of Earth terrains that can be viewed and traversed in real time. Finally, EasyScene software control the actions among interactive objects within a virtual world. Coryphaeus products are used on Silican Graphics workstation and supercomputers to simulate real-world performance in synthetic environments. Customers include aerospace, aviation, architectural and engineering firms, game developers, and the entertainment industry.

Source record↗

NASA NTRS1987

Dynamics formulations for the real-time simulation of constrained motion

The Space Shuttle program has relied heavily on simulation throughout all phases of development and operation. Real-time, man-in-the-loop simulation has served the NASA manned space flight program by providing the means to evaluate systems design and integrated systems performance in a simulated flight environment as well as provide a means to train flight crews. New challenges are presented by the development and operation of a permanently manned space station. The assembly of the space station, the transferral of payloads and the use of the space station manipulator to berth the Orbiter are operations critical to the success of the space station. All these operations are examples of constrained motion among the bodies associated with the Orbiter and space station system. The state of the art of formulating the governing dynamical equations of motion for constrained systems are described. The uses of the two basic problems in multibody dynamics are discussed. The most efficient formulations of the equations of motion are addressed from the point of view of completeness. The issues surrounding incorporating the constraints into the equation of motion are presented.

Kelly, Frederick A.↗

NASA NTRS1979

Synthesis of rotor test data for real-time simulation

A mathematical model of a hingeless tilting rotor is presented. The model was obtained by a systematic curve fit procedure applied to an extensive set of model scale wind tunnel data. The math model equations were used in a real time flight simulation model of a hingeless tilt rotor XV-15 to assess changes in flying qualities compared to those obtained using a previous rotor model. Extensive plots of the rotor derivatives are given. Discussions of attempts to apply multivariable linear regression technqiues to the data and the use of an analytical rotor representation are included.

Mcveigh, M. A.↗

NASA NTRS1989

Real-time simulation of an F110/STOVL turbofan engine

A traditional F110-type turbofan engine model was extended to include a ventral nozzle and two thrust-augmenting ejectors for Short Take-Off Vertical Landing (STOVL) aircraft applications. Development of the real-time F110/STOVL simulation required special attention to the modeling approach to component performance maps, the low pressure turbine exit mixing region, and the tailpipe dynamic approximation. Simulation validation derives by comparing output from the ADSIM simulation with the output for a validated F110/STOVL General Electric Aircraft Engines FORTRAN deck. General Electric substantiated basic engine component characteristics through factory testing and full scale ejector data.

Drummond, Colin K.↗

NASA NTRS1984

Some real-time simulation applications to Space Shuttle approach and landing design and test

In the present discussion of the roles played by real time, man-in-the-loop engineering simulation in the development of NASA Space Shuttle approaches and landings, attention is given to the function of the simulator as a design and verification tool. Aspects of the problem posed by Shuttle landings, and the difficulties involved in this problem's quantification, are noted. Recent results of control system studies for pitch axis control, using fixed- and motion-base simulators, are discussed.

Law, H. G., III↗