Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “reaction plane”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Mixing in the dome region of a staged gas turbine combustor

To lower NO(x) emissions from gas-turbine engines the effect of dome design and operational changes on the mixing quality in the fuel-rich region is studied. A statistical analysis is employed to establish the parametric sensitivity in this complex flow. A mixing-effectiveness index is defined and used to optimize the gas-species uniformity and the extent of reaction at the exit plane of the dome. Mixing effectiveness is tied to the fuel and air injection locations, the macroscale structure of the dome aerodynamics, and the level of turbulence. Increases in nozzle/air to fuel ratio, reference velocities, and the dome expansion angle increased the level of turbulence. The optimum configuration featured counter-swirling fuel and air streams and produced a strong torroidal recirculation zone, an effective spray angle of 45 degrees, and azimuthal velocities that decayed to zero inside of two duct diameters. The results underscore the system specific nature of mixing optimization.

Sowa, W. A.↗
NASA NTRS2015

Skylon Aerodynamics and SABRE Plumes

An independent partial assessment is provided of the technical viability of the Skylon aerospace plane concept, developed by Reaction Engines Limited (REL). The objectives are to verify REL's engineering estimates of airframe aerodynamics during powered flight and to assess the impact of Synergetic Air-Breathing Rocket Engine (SABRE) plumes on the aft fuselage. Pressure lift and drag coefficients derived from simulations conducted with Euler equations for unpowered flight compare very well with those REL computed with engineering methods. The REL coefficients for powered flight are increasingly less acceptable as the freestream Mach number is increased beyond 8.5, because the engineering estimates did not account for the increasing favorable (in terms of drag and lift coefficients) effect of underexpanded rocket engine plumes on the aft fuselage. At Mach numbers greater than 8.5, the thermal environment around the aft fuselage is a known unknown−a potential design and/or performance risk issue. The adverse effects of shock waves on the aft fuselage and plumeinduced flow separation are other potential risks. The development of an operational reusable launcher from the Skylon concept necessitates the judicious use of a combination of engineering methods, advanced methods based on required physics or analytical fidelity, test data, and independent assessments.

Mehta, Unmeel↗
DOE OSTI2023

Two-dimensional ruthenium boride: a Dirac nodal loop quantum electrocatalyst for efficient hydrogen evolution reaction

Catalysts with high carrier mobility, high activity, and an active basal plane have been highly sought for the hydrogen evolution reaction (HER). However, combining these advantages into one single material is a grand challenge. Herein, using first principles computations, we predicted that a two-dimensional (2D) Dirac nodal loop semimetal, namely the RuB 4 monolayer, is promising as a superior catalyst for the HER. Our systematic computations showed that the single layer RuB 4 is thermodynamically, dynamically, mechanically, and thermally stable and presents multiple Ru and B sites for the HER on the basal plane. The estimated Gibbs free energy for hydrogen adsorption at a Ru site is approaching zero (–8.8 meV), suggesting its excellent HER performance. The RuB 4 monolayer is a Dirac nodal loop semimetal with high Fermi velocities, which can accelerate charge transfer between catalysts and reaction intermediates. The RuB 4 monolayer is an auxetic material with an out-of-plane negative Poisson's ratio, implying its novel mechanical properties. Finally, this work provides an example of using a Dirac nodal loop semimetal for high-performance HER catalysts, which is a promising alternative to the known catalysts with trivial metallic properties.

30 DIRECT ENERGY CONVERSION↗
NASA NTRS1989

Tethered Satellite System control system design

This paper discusses the control aspects of the Tethered Satellite System mission. The deployer controls system uses length-error and tension-error feedback to control in-plane libration, length, and length rate. The satellite's reaction control system is used to augment tether tension, control rates and attitude about the tether axis, and to damp in-plane and out-of-plane libration. The orbiter's reaction control system is also used to control in-plane and out-of-plane libration. Results of simulations are presented for the flight portion of the Tethered Satellite System mission.

Tomlin, Donald D.↗
DOE OSTI2020

Transport Processes in a Li-ion Cell during an Internal Short-Circuit

Internal short-circuit in a lithium-ion cell causes an abrupt increase in cell temperature and triggers subsequent thermal runaway. In this work, we present a detailed electrochemical-thermal model to investigate the physical behavior during an internal short-circuit. Simulations at wide range of heat transfer coefficients and short-circuit resistances are conducted to illustrate electrochemical and thermal behavior under a wide range of conditions. The Joule heating at the shorted region promotes electrochemical reactions nearby, causing in-plane non-uniformity of electrolyte and active material transport. Furthermore, it is found that diffusion in solid active materials plays a significant role at very high shorting currents (~20 C), as electrochemical reactions rate are being controlled progressively more by availability of Li + at the interface, due to limitations in diffusion through the active material with increasing discharge rates. This diffusion limitation causes a drop in available energy, and subsequently a decrease in cell equilibrium potential and the heat generation rate at the location of the short. On the other hand, rapid depletion of lithium concentration in the electrolyte and accumulation on the electrode surface results in highly non-uniform transport properties resulting in higher heat generation rates. Hence, the heating regime shifts from "local heating" to "global heating". Based on the findings, important design parameters for battery safety are discussed.

25 ENERGY STORAGE↗
DOE OSTI2023

Crosslinking and Gelation of Polymer Brushes and Free Polymer Chains in a Confined Space during Controlled Radical Polymerization-A Computer Simulation Study

The confinement effect on crosslinking and gelation during controlled/living copolymerization of a monovinyl and a divinyl monomer was studied by Monte Carlo computer simulation using the dynamic lattice liquid method. The simulated reactions took place in plane-parallel slits of various widths for various grafting densities (GDs) and various initial initiator/crosslinker ratios ([X] 0 /[Ini] 0 ). Monomers and crosslinkers were initially randomly distributed in the slit, but initiators were either anchored to one solid plane (polymer brushes) or randomly distributed (free chains). For brushes, the gel point (GP) depended on GD and [X] 0 /[Ini] 0 . The higher these parameters, the lower was the gel point. The gel point was also affected by the slit width. For free, nongrafted chains, the dependence of GP on slit width was negligible. For brushes, a nonuniform density of crosslinks was found, the highest density was close to the wall. This asymmetry was high at the gel point and decreased at higher conversions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Continuous Encodable Reshaping of Gold Nanocrystals through Facet Modulation

Shape control of nanocrystals (NCs) is crucial for tuning their assembly behavior and functional properties, yet the precise manipulation of facet composition remains challenging. Here, we present a nanocrystal reshaping strategy to control and modulate the facets of gold (Au) NCs. Our one-pot approach, conducted at room temperature, requires only initial Au NCs, Au 3+ ions, and surfactants, distinguishing it from conventional reduction-mediated “etching-and-regrowth” methods. Detailed structural studies using electron microscopy, small-angle X-ray scattering (SAXS), and UV−vis spectroscopy reveal the surfactant-encoded pathway for NC transformation from shaped particles to spheres and then into various polyhedral shapes while preserving the individual particles' volume. The proposed reshaping mechanism involves the dissolution of surface Au atoms into Au + complexes in the presence of Au 3+ and surfactant, followed by surfactant-guided redeposition and formation of facets with different atomic planes. Using the ethanol oxidation reaction (EOR) as a probe, we observe a quasi-linear decrease in onset potential and an increase in activity with increasing {100} facet exposure. This work broadens synthetic strategies by offering precise NC reshaping and facet control.

36 MATERIALS SCIENCE↗
DOE OSTI2025

New proton emitter 188 At implies an interaction unprecedented in heavy nuclei

We report the discovery of a new atomic nucleus 188 At, which is the heaviest proton-emitting isotope known to date. The new activity was observed through the 107 Ag( 84 Sr, 3n) 188 At fusion-evaporation reaction using the focal-plane spectrometer of the gas-filled recoil separator in the Accelerator Laboratory of the University of Jyväskylä, Finland. To fully interpret the experimental data, we have expanded the non-adiabatic quasiparticle model to treat nuclei in the beyond-lead region. The description reproduced the measured decay rate and pointed towards emission from an extremely prolate-deformed state with a dominant s 1/2 proton component in the wave function. The Thomas-Ehrman shift can be enhanced in low angular momentum states, but such effects have not been observed in heavy nuclei. The single-proton separation energy of 188 At deviates from that extrapolated from the systematics, which can be interpreted as the first evidence of this effect in heavy nuclei.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Momentum conservation in current drive and alpha-channeling-mediated rotation drive

Alpha channeling uses waves to extract hot ash from a fusion plasma, transferring energy from the ash to the wave. It has been proposed that this process could create a radial electric field, efficiently driving E × B rotation. However, existing theories ignore the nonresonant particles, which play a critical role in enforcing momentum conservation in quasilinear theory. Because cross field charge transport and momentum conservation are fundamentally linked, this non-consistency throws the rotation drive into question. This paper has two main goals. First, we provide a pedantic and cohesive introduction to the recently developed simple, general, self-consistent quasilinear theory for electrostatic waves that explains the torques which allow for current drive parallel to the magnetic field, and charge extraction across it; a theory that has largely resolved the question of rotation drive by alpha channeling. We show how the theory reveals a fundamental difference between the reaction of nonresonant particles to plane waves that grow in time vs steady-state waves that have a nonuniform spatial structure, allowing rotation drive in the latter case while precluding it in the former, and we review the local and global conservation laws that lead to this result. Second, we provide two new results in support of the theory. First, we provide a novel two-particle Hamiltonian model that rigorously establishes the relationship between charge transport and momentum conservation. Second, we compare the new quasilinear theory to the oscillation-center theories of ponderomotive forces, showing how the latter often obscure the time-dependent nonresonant recoil, but ultimately lead to similar results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Designing interphases for practical aqueous zinc flow batteries with high power density and high areal capacity

Aqueous zinc flow batteries (AZFBs) with high power density and high areal capacity are attractive, both in terms of cost and safety. A number of fundamental challenges associated with out-of-plane growth and undesirable side reactions on the anode side, as well as sluggish reaction kinetics and active material loss on the cathode side, limit practical deployment of these batteries. We investigated artificial interphases created using a simple electrospray methodology as a strategy for addressing each of these challenges. The effectiveness of the electrospray interphases in full cell zinc-iodine flow batteries was evaluated and reported; it is possible to simultaneously achieve high power density [115 milliwatts per square centimeter (mW/cm 2 )] and high areal capacity [25 milliampere hour per square centimeter (mA·hour/cm 2 )]. Last, we extended it to aqueous zinc-bromine and zinc-vanadium flow batteries of contemporary interest. It is again found that high power density (255 and 260 mW/cm 2 , respectively) and high areal capacity (20 mA·hour/cm 2 ) can be simultaneously achieved in AZFBs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

First-Principles Examination of Multiple Criteria of Organic Solvent Oxidative Stability in Batteries

Oxidative instability of the liquid electrolyte at or near battery cathode oxide surfaces has significant detrimental effects on batteries. Organic solvent molecules are often the fuel and precursors of such degradation processes, releasing electrons and protons that react with cathode oxides and electrolyte anions. These reactions contribute to cathode–electrolyte interphase (CEI) film formation, transition-metal ion dissolution, and phase transformation of the surface regions of the cathode. Here we apply density functional theory calculations to examine four criteria of oxidative stability (oxidation potential, hydrogen removal energies, and initial reactivity on two types of oxide facets) using four different solvent/additive molecules (ethylene carbonate, fluoroethylene carbonate, 1,3-dioxolane, and dimethyl ether). The ranking of molecular stability differs with each criterion. Surprisingly, the all-oxygen-terminated basal planes of layered oxides exhibit lower reaction barriers than spinel surface facets with exposed transition-metal cations, especially for ether solvents; the calculations also suggest basal planes contribute to the dissolution of transition-metal ions. Further, the structure–degradation relation complexity underscores the challenge of understanding the function of the CEI but also offers a guide to future degradation-mitigation strategies including facet engineering. Our predictions and models help establish a framework for future studies relevant to high-voltage conditions.

25 ENERGY STORAGE↗
DOE OSTI2022

Local Structure of Sulfur Vacancies on the Basal Plane of Monolayer MoS 2

We report the nature of the S-vacancy is central to controlling the electronic properties of monolayer MoS 2 . Understanding the geometric and electronic structures of the S-vacancy on the basal plane of monolayer MoS 2 remains elusive. Here, operando S K-edge X-ray absorption spectroscopy shows the formation of clustered S-vacancies on the basal plane of monolayer MoS 2 under reaction conditions (H 2 atmosphere, 100–600 °C). First-principles calculations predict spectral fingerprints consistent with the experimental results. The Mo K-edge extended X-ray absorption fine structure shows the local structure as coordinatively unsaturated Mo with 4.1 ± 0.4 S atoms as nearest neighbors (above 400 °C in an H 2 atmosphere). Conversely, the 6-fold Mo–Mo coordination in the crystal remains unchanged. Electrochemistry confirms similar active sites for hydrogen evolution. The identity of the S-vacancy defect on the basal plane of monolayer MoS 2 is herein elucidated for applications in optoelectronics and catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Synergistic ruthenium single-atom and nanoparticles in nickel as cooperative catalysts for the alkaline hydrogen evolution reaction

Efficient hydrogen evolution reaction (HER) catalysts that reduce the use of noble metals and can be synthesized on a large scale are essential for advancing anion exchange membrane water electrolyzers (AEMWEs) toward commercialization. Herein, we present a composite catalyst in which Ru nanoparticles coexist with Ru single-atom alloys (SAAs) dispersed within Ni nanoparticles (Ru-SAA/Ni), creating a highly active HER electrocatalyst. Using a one-pot and scalable synthesis method, we can tune the material composition from SAA, i.e. materials containing atomically dispersed Ru atoms (with ≤0.4 at% Ru) to composite structures in which SAAs coexist with Ru NPs. Comprehensive characterization using XPS, XAS, and TEM confirms Ru-SAA formation at a low Ru content and composite structures at higher contents. Electrochemical evaluations conducted in a three-electrode setup reveal that Ru-SAA/Ni composites achieve HER performance on par with that of Pt/C. Computational insights suggest that water dissociation is significantly faster at the Ru/Ni interface compared with that on extended surfaces. These active sites are thermodynamically as active as basal planes, preventing the excessive accumulation of reaction intermediates (H*, OH*). All these results highlight the synergistic interaction between Ru SAAs and Ru nanoparticles and their potential for large-scale applications with minimal use of precious metals. Finally, the materials are processed and tested in AEMWEs, achieving 1.85 V at 0.5 A cm −2 with a total noble metal loading of only 0.1 mg cm −2 .

Khalil, Gaëlle [Université de Paris (France)]↗
NASA NTRS2010

DVA as a Diagnostic Test for Vestibulo-Ocular Reflex Function

The vestibulo-ocular reflex (VOR) stabilizes vision on earth-fixed targets by eliciting eyes movements in response to changes in head position. How well the eyes perform this task can be functionally measured by the dynamic visual acuity (DVA) test. We designed a passive, horizontal DVA test to specifically study the acuity and reaction time when looking in different target locations. Visual acuity was compared among 12 subjects using a standard Landolt C wall chart, a computerized static (no rotation) acuity test and dynamic acuity test while oscillating at 0.8 Hz (+/-60 deg/s). In addition, five trials with yaw oscillation randomly presented a visual target in one of nine different locations with the size and presentation duration of the visual target varying across trials. The results showed a significant difference between the static and dynamic threshold acuities as well as a significant difference between the visual targets presented in the horizontal plane versus those in the vertical plane when comparing accuracy of vision and reaction time of the response. Visual acuity increased proportional to the size of the visual target and increased between 150 and 300 msec duration. We conclude that dynamic visual acuity varies with target location, with acuity optimized for targets in the plane of rotation. This DVA test could be used as a functional diagnostic test for visual-vestibular and neuro-cognitive impairments by assessing both accuracy and reaction time to acquire visual targets.

Wood, Scott J.↗
DOE OSTI2024

Novel signatures of radiation reaction in electron–laser sidescattering

In this article we investigate novel signatures of radiation reaction via the angular deflection of an electron beam colliding at 90 degrees with an intense laser pulse. Due to the radiation reaction effect, the electrons can be deflected towards the beam axis for plane wave backgrounds, which is not possible in the absence of radiation reaction effects. The magnitude and size of the deflection angle can be controlled by tailoring the laser pulse shapes. The effect is first derived analytically using the Landau–Lifshitz equation, which allows to determine the important scaling behavior with laser intensity and particle energy. We then move on to full scale 3D Monte Carlo simulations to verify the effect is observable with present day laser technology. We investigate the opportunities for an indirect observation of laser depletion in such side scattering scenarios.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS1981

Mechanism and models for zinc metal morphology in alkaline media

Based on experimental observations, a mechanism is presented to explain existence of the different morphologies of electrodeposited zinc in alkaline solution. The high current density dendrites appear to be due to more rapid growth on the nonbasal crystallographic planes than on the basal plane. The low current density moss apparently results from dissolution from the nonbasal planes at low cathodic voltages. Electrochemical models were sought which would produce such a phenomenon. The fundamental plating mechanism alone accounts only for different rates on different planes, not for zinc dissolution from a plane in the cathodic region. Fourteen models were explored; two models were in accord with the proposed mechanism. One involves rapid disproportionation of the zinc +1 species on the nonbasal planes. The other involves a redox reaction (corrosion) between the zinc-zincate and hydrogen-water systems.

May, C. E.↗
NASA NTRS1984

Geodynamics of crustal deformation and seismotectonic block movements in central Europe

Geological observations reveal the style of neotectonic near-surface stresses and deformations in central Europe. Seismic activity, focal depths and fault plane solutions of earthquakes indicate kinematic reactions within the crust. A crustal deformation model which may account for the Rhine graben systems and the associated seismotectonic block movements in Europe is presented. A computer aided tomography to gravity anomalies is used in determining the crustal stresses in central Europe. Tomographical interpretations of gravity data with respect to seismic stresses are discussed. Kinematics and dynamics are integrated to show that the measured regional stresses in central Europe are derivable from the convection generated traction on the boundary of the elastic spherical shell of the crust as inferred from satellite derived gravity data.

Liu, H. S.↗
NASA NTRSDate not supplied

Show Me the Money! Evaluating A Graduated Incentive Structure to Keep Respondents Engaged Through 101 Surveys in 28 Days

We report the results of a survey test conducted in advance of a series of community response tests (CRTs) to evaluate response to noise from NASA’s X-59 aircraft. The CRTs will require a substantial number of observations to generate a dose response curve for noise exposure and related annoyance levels and the timeframe is limited due to resource and scheduling constraints with an experimental aircraft. Within each CRT area, we will recruit a sample of residents in advance and ask them to fill out a brief survey each time the aircraft passes over. Respondents will be asked to fill out the survey either on the web or as part of an application they are able to download onto their mobile phones. Respondents will be notified each time the plane flies over, asking for their reactions. On many days, respondents will be asked to fill out the survey for multiple flights. Typical incentives are used during the recruitment phase (pre-incentive for a household screener and post-paid for a background survey completed by the selected respondent) and post-paid for an end of study survey. To improve response rates over such a demanding survey schedule (101 surveys in 28 days) we will implement a weekly incentive based upon participation rates, with higher incentives for greater participation and increasing rates each week. The survey test will follow the proposed methodology of the CRTs. We will report on the participation rates by incentive amount and the effectiveness of the incentive structure in obtaining and maintaining response rates over the 4 weeks. We will examine how quickly participation fades over the 4-week period and consider whether the incentive schedule could be improved by altering the distribution of payments. Finally, we will compare how these rates varied across web and app respondents. We will use the results of this work to confirm or improve the design of the CRTs, ensuring the collection of data needed by NASA to evaluate the impact of this innovative technology.

incentives↗