Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “power electronics material”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

CarbAl Heat Transfer Material

The increasing use of power electronics, such as high-current semiconductor devices and modules, within space vehicles is driving the need to develop specialty thermal management materials in both the packaging of these discrete devices and the packaging of modules consisting of these device arrays. Developed by Applied Nanotech, Inc. (ANI), CarbAl heat transfer material is uniquely characterized by its low density, high thermal diffusivity, and high thermal conductivity. Its coefficient of thermal expansion (CTE) is similar to most power electronic materials, making it an effective base plate substrate for state-of-the-art silicon carbide (SiC) super junction transistors. The material currently is being used to optimize hybrid vehicle inverter packaging. Adapting CarbAl-based substrates to space applications was a major focus of the SBIR project work. In Phase I, ANI completed modeling and experimentation to validate its deployment in a space environment. Key parameters related to cryogenic temperature scaling of CTE, thermal conductivity, and mechanical strength. In Phase II, the company concentrated on improving heat sinks and thermally conductive circuit boards for power electronic applications.

Fink, Richard↗

Foreword: Special Section on Multiphysics Aspects of Power Electronics Packaging—Power Die, Power Module, and Converter Level: Part 2

Power electronics are increasingly being used to condition electricity for a wide array of applications, such as transportation (on land, air, and water), data centers, radio frequency, directed energy, wind, solar, and grid-tied applications. Here, to increase power density, performance, efficiency, and reliability-as well as to reduce cost-innovations and developments are needed in the multiphysics packaging of power electronics at a die, module, and converter level. This includes fundamental R&D related to emerging high-voltage, high-temperature, and high-switching-frequency power electronics, packaging materials, thermal materials and interfaces, fluid-based thermal management technologies, reliability, condition monitoring, and prognostics. Latest developments in this area are published as a Special Section on Multiphysics Aspects of Power Electronics Packaging. The first part was published in the May 2024 issue of the IEEE Transactions on Components, Packaging and Manufacturing Technology (Volume 14, Issue 5). The second part of that Special Section is being published in this issue. A brief summary of the papers included in the second part are given below.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Thermomechanical Modeling of High-Temperature Bonded Interface Materials

In an automotive power electronics package, bonded interface materials play a critical role in providing a smooth heat dissipation path from the device to the coolant. However, these materials are susceptible to failure when the package gets exposed to repeated changes in its thermal environment and internal temperature variations. Under these thermal conditions, the coefficient of thermal expansion mismatch between the different component layers results in thermally induced stresses and consequently the delamination of the material from its adjoining surfaces or crack initiation and propagation within the material. Thermomechanical modeling offers a path to study the complex nature of these bonded materials, guides their design and selection, and, in conjunction with experimental results, plays an important role in predicting their lifetime. In this chapter, two modeling strategies - similar in approach and implementation but different in the underlying theory - are discussed in the context of high-temperature bonded materials. In addition, a short review of sintered silver is provided, as it is widely seen as a potentially promising and reliable bonded material for high-temperature applications.

36 MATERIALS SCIENCE↗

Optimum Planning for Inductively Charged On-Demand Automated Electric Shuttles at Greenville, South Carolina

Wireless charging technology presents perfect fits for autonomous electric vehicles for realizing a fully automated system (vehicle and charger). This paper presents a planning optimization analysis for a pilot project of in-route wireless charging infrastructure serving fixed-route on-demand shared automated electric shuttles (SAESs) at Greenville, South Carolina, USA. A single-objective non-linear integer planning optimization problem is formulated. A comprehensive cost function representing the inductively charged SAESs is developed, considering road construction, power electronics and materials, traction battery, and installation costs. The optimization problem is solved to determine the best combination of the system key design parameters (number and allocations of wireless chargers, charging power level, track length and on-board battery capacity) that show the most cost-effective solution and allow the SAESs realizing charge sustaining operation. The planning platform incorporates representative simulated traffic data (drive cycles and routes) for four SAESs at Greenville project using the Simulation of Urban Mobility (SUMO) tool. These data are fed to a vehicle powertrain model and a wireless charger power model to predict the battery power, energy and state-of-charge (SOC) profiles, which are provided to the search algorithm to assess the design objectives under specific constraints. The results indicated that implementing wireless charging at a few designated stops for fixed-route SAESs with proper design allows the vehicles realizing charge sustaining operation, infinite range and zero recharge downtime, with a significant reduction in the on-board battery (36 % ) and road coverage (69%), at minimum cost.

33 ADVANCED PROPULSION SYSTEMS↗

Planning Optimization for Inductively Charged On-demand Automated Electric Shuttles Project at Greenville, South Carolina

Wireless charging technology presents an ideal fit for autonomous electric vehicles for realizing a fully automated system (vehicle and charger). This paper presents a planning optimization analysis for a pilot project of in-route wireless charging infrastructure serving fixed-route on-demand shared automated electric shuttles (SAESs) at Greenville, South Carolina, USA. A single-objective non-linear mixed integer system planning optimization problem is formulated. A comprehensive cost model representing the overall inductively charged SAESs system is developed, considering road construction, power electronics and materials, traction battery, and installation costs. The optimization problem is solved to determine the best combination of the system key design parameters (number and allocations of wireless chargers, charging power level, track length and on-board battery capacity) that show the most cost-effective solution and allow the SAESs to achieve charge-sustaining operation. The planning platform incorporates representative simulated traffic data (driving speed and routes) for four SAESs in the Greenville using the Simulation of Urban Mobility tool. These data are fed to a vehicle powertrain model and a wireless charger power model to predict the battery power, energy and state-of-charge profiles, which are provided to the search algorithm to assess the design objectives under specific constraints. Finally, the results indicate that implementing high-power (100 kW) wireless charger at a few designated stops for fixed-route SAESs with the proper track length allows the vehicles to realize charge-sustaining operation, infinite range, and zero recharge downtime, with a significant reduction in the on-board battery (36%) and road coverage (69%), at minimum cost.

33 ADVANCED PROPULSION SYSTEMS↗

Self-Resonant Coil Design for High-frequency High-Power Inductive Wireless Power Transfer

In this paper, the design methodology of a high-frequency, high-power, long-distance inductive wireless power transfer (WPT) is presented. The airgap (d) of a traditional high-power (>1 kW) WPT is limited to a few hundred millimeters, which is almost 1/4th of the coil diameter, D; d ≤ D/4. In this paper, the power transfer distance is significantly increased (d ≥ 1.5D) by adopting a high-frequency magnetic design and GaN-based power electronics. The material and design of the coil and shield are investigated using FEA and tested experimentally. A high frequency 6.78 MHz wireless charging system was built to transfer 1 kW power over 3 m airgap.

Mohammad, Mostak↗

Thermal expansion coefficients of high thermal conducting BAs and BP materials

Recently reported very high thermal conductivities in cubic boron arsenide (BAs) and boron phosphide (BP) crystals could potentially provide a revolutionary solution in the thermal management of high power density devices. To fully facilitate such an application, the compatible coefficient of thermal expansion (CTE) between the heat spreader and the device substrate, in order to minimize the thermal stress, needs to be considered. Here, we report our experimental CTE studies of BAs and BP in the temperature range from 100 K to 1150 K, through a combination of X-ray single crystal diffraction and neutron powder diffraction. Here, we demonstrated that the room temperature CTEs, 3.6 ± 0.15 × 10 –6 /K for BAs and 3.2 ± 0.2 × 10 –6 /K for BP, are more compatible with most of the semiconductors including Si and GaAs, in comparison with diamond, and thus could be better candidates for the future heat spreader materials in power electronic devices.

36 MATERIALS SCIENCE↗

Effects of pyrolysis conditions on dielectric properties of PLZT films derived from a polyvinylpyrrolidone-modified sol-gel process

Graphical abstract: SEM images showing the surface morphology of PLZT films derived from solutions with various PVP content and treated with either RTA (rapid thermal annealing) or SPT (step-wise preheat treatment) process. Highlights: Black-Right-Pointing-Pointer High-quality PLZT films were fabricated by using a polyvinylpyrrolidone-modified sol-gel method. Black-Right-Pointing-Pointer Improved film density and integrity was achieved by employing a novel step-wise preheat treatment (SPT) process. Black-Right-Pointing-Pointer Enhanced dielectric properties were correlated to the improved microstructures as a result of the SPT process. -- Abstract: Pb{sub 0.92}La{sub 0.08}Zr{sub 0.52}Ti{sub 0.48}O{sub 3} (PLZT) films were deposited on platinized silicon substrates (Pt/Si) using a polyvinylpyrrolidone (PVP) modified sol-gel method. Pyrolysis of the green films was conducted via two methods: rapid thermal annealing (RTA) and a step-wise preheat treatment (SPT). Microstructure analysis and dielectric property characterization were performed on samples treated by these two methods. Results showed that the SPT-pyrolyzed films exhibited much better dielectric properties when compared with the RTA-pyrolyzed films. The differences in dielectric properties were correlated to microstructural features caused by the different pyrolysis conditions. High-quality PLZT films with high dielectric constant ( Almost-Equal-To 860 at zero bias) and high breakdown strength ( Almost-Equal-To 2.1 MV/cm) were fabricated under controlled pyrolysis conditions. This work demonstrated the potential application of this material for power electronics in electric drive vehicles.

36 MATERIALS SCIENCE↗

Soft Magnetic Multilayered FeSiCrB–Fe$_{x}$N Metallic Glass Composites Fabricated by Spark Plasma Sintering

Novel multilayered FeSiCrB–Fe $_{x}$ N ( x = 2–4) metallic glass composites were fabricated using spark plasma sintering of FeSiCrB amorphous ribbons (Metglas 2605SA3 alloy) and Fe $_{x}$ N ( x = 2–4) powder. Crystalline Fe $_{x}$ N can serve as a high magnetic moment, high electrical resistance binder, and lamination material in the consolidation of amorphous and nanocrystalline ribbons, mitigating eddy currents while boosting magnetic performance and stacking factor in both wound and stacked soft magnetic cores. Stacking factors of nearly 100% can be achieved in an amorphous ribbon/iron nitride composite. FeSiCrB–Fe $_{x}$ N multilayered metallic glass composites prepared by spark plasma sintering have the potential to serve as a next-generation soft magnetic material in power electronics and electrical machines.

36 MATERIALS SCIENCE↗

Localized UV emitters on the surface of β-Ga 2 O 3

Abstract Monoclinic gallium oxide (β-Ga 2 O 3 ) is attracting intense focus as a material for power electronics, thanks to its ultra-wide bandgap (4.5–4.8 eV) and ability to be easily doped n -type. Because the holes self-trap, the band-edge luminescence is weak; hence, β-Ga 2 O 3 has not been regarded as a promising material for light emission. In this work, optical and structural imaging methods revealed the presence of localized surface defects that emit in the near-UV (3.27 eV, 380 nm) when excited by sub-bandgap light. The PL emission of these centers is extremely bright—50 times brighter than that of single-crystal ZnO, a direct-gap semiconductor that has been touted as an active material for UV devices.

36 MATERIALS SCIENCE↗

Double-Sided Pressureless-Sintered-Silver Interconnects Fabricated by Reflow-Oven-Processing

A significant amount of development with sintered-silver as an alternative interconnect (or attachment or attach) material in power electronic devices has occurred since ~ 2010 at Oak Ridge National Laboratory's National Transportation Research Center. Continuous sponsorship of the work enabled improvements and understanding of several sequential processing steps which otherwise would not have occurred with a short duration or an intermittently funded project. The majority of that work has occurred with a focus on improving its processing and consequential mechanical reliability of the interconnect while promoting adaptability to power elect ronic device manufacturing. The work includes determining application issues of silver-sintering and the developing processes that would make it amenable for use with reflow oven sintering. As part of that work, co-development of maximum interconnect strength of the sintered-silver interconnect occurred, and that also involved examining candidate plating materials that could be used in concert with them for the "interconnect system". All of this work involved the consideration of a single sintered-silver interconnect.

36 MATERIALS SCIENCE↗

2013 DOE Vehicle Technologies Office Annual Merit Review

The 2013 U.S. Department of Energy (DOE) Fuel Cell Technologies Office (FCTO) and Vehicle Technologies Office (VTO) Annual Merit Review and Peer Evaluation Meeting (AMR) was held May 13-17, 2013, in Crystal City, Virginia. The review encompassed all of the work done by the FCTO and the VTO: a total of 287 individual activities were reviewed for VTO, by a total of 187 reviewers. A total of 1,382 individual review responses were received for the VTO technical reviews. The objective of the meeting was to review the accomplishments and plans for VTO over the previous 12 months, and provide an opportunity for industry, government, and academia to give inputs to DOE on the Office with a structured and formal methodology. The meeting also provided attendees with a forum for interaction and technology information transfer.

33 ADVANCED PROPULSION SYSTEMS↗

2014 Annual Merit Review, Vehicle Technologies Office: Results Report

The 2014 U.S. Department of Energy (DOE) Fuel Cell Technologies Office (FCTO) and Vehicle Technologies Office (VTO) Annual Merit Review and Peer Evaluation Meeting (AMR) was held June 16-20, 2014, in Washington, DC. The review encompassed all of the work done by the FCTO and the VTO: a total of 295 individual activities were reviewed for VTO, by a total of 179 reviewers. A total of 1,354 individual review responses were received for the VTO technical reviews. The objective of the meeting was to review the accomplishments and plans for VTO over the previous 12 months, and provide an opportunity for industry, government, and academia to give inputs to DOE on the Office with a structured and formal methodology. The meeting also provided attendees with a forum for interaction and technology information transfer.

33 ADVANCED PROPULSION SYSTEMS↗

2015 DOE Vehicle Technologies Office Annual Merit Review

The 2015 U.S. Department of Energy (DOE) Fuel Cell Technologies Office (FCTO) and Vehicle Technologies Office (VTO) Annual Merit Review and Peer Evaluation Meeting (AMR) was held June 8-12, 2015, in Arlington, Virginia. The review encompassed all of the work done by the FCTO and the VTO: 258 individual activities were reviewed for VTO, by 170 reviewers. A total of 1,095 individual review responses were received for the VTO technical reviews. The objective of the meeting was to review the accomplishments and plans for VTO over the previous 12 months, and provide an opportunity for industry, government, and academia to give inputs to DOE on the Office with a structured and formal methodology. The meeting also provided attendees with a forum for interaction and technology information transfer.

33 ADVANCED PROPULSION SYSTEMS↗

2017 DOE Vehicle Technologies Office Annual Merit Review

The 2017 U.S. Department of Energy (DOE) Hydrogen and Fuel Cells Program and Vehicle Technologies Office (VTO) Annual Merit Review and Peer Evaluation Meeting (AMR) was held June 5-9, 2017, in Washington, DC. The review encompassed work done by the Hydrogen and Fuel Cells Program and VTO: 263 individual activities were reviewed for VTO by 191 reviewers. Exactly 1,241 individual review responses were received for the VTO technical reviews. The objective of the meeting was to review the accomplishments and plans for VTO over the previous 12 months, and provide an opportunity for industry, government, and academia to give inputs to DOE with a structured and formal methodology. The meeting also provided attendees with a forum for interaction and technology information transfer.

33 ADVANCED PROPULSION SYSTEMS↗

2016 DOE Vehicle Technologies Office Annual Merit Review

The 2016 U.S. Department of Energy (DOE) Hydrogen and Fuel Cells Program and Vehicle Technologies Office (VTO) Annual Merit Review and Peer Evaluation Meeting (AMR) was held June 6-9, 2016, in Washington, DC. The review encompassed work done by the Hydrogen and Fuel Cells Program and VTO: 226 individual activities were reviewed for VTO, by 171 reviewers. A total of 1,044 individual review responses were received for the VTO technical reviews. The objective of the meeting was to review the accomplishments and plans for VTO over the previous 12 months, and provide an opportunity for industry, government, and academia to give inputs to DOE with a structured and formal methodology. The meeting also provided attendees with a forum for interaction and technology information transfer.

33 ADVANCED PROPULSION SYSTEMS↗

Vehicle Technologies Office 2018 Annual Merit Review

The 2018 U.S. Department of Energy (DOE) Vehicle Technologies Office (VTO) Annual Merit Review (AMR) was held June 18-21, 2018, in Arlington, Virginia. The review encompassed work done by VTO: 235 individual activities were reviewed by 247 reviewers. Exactly 1,202 individual review responses were received for the VTO technical reviews. The objective of the meeting was to review VTO accomplishments over the previous 12 months and provide an opportunity for industry, government, and academia to give inputs to DOE with a structured and formal methodology. The meeting also provided attendees with a forum for interaction and technology information transfer.

25 ENERGY STORAGE↗

2019 Vehicle Technologies Office Annual Merit Review Report

The 2019 U.S. Department of Energy (DOE), Office of Energy Efficiency and Renewable Energy’s (EERE) Vehicle Technologies Office (VTO) Annual Merit Review (AMR) was held June 10-13, 2019, in Arlington, Virginia. The review encompassed work done by VTO: 287 individual activities were reviewed by 272 reviewers. Exactly 1,162 individual review responses were received for the VTO technical reviews. The objective of the meeting was to review the accomplishments and plans for VTO over the previous 12 months, and provide an opportunity for industry, government, and academia to give inputs to DOE on the Office with a structured and formal methodology. The meeting also provided attendees with a forum for interaction and technology information transfer.

03 NATURAL GAS↗