Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “population count”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Leveling coatings for reducing the atomic oxygen defect density in protected graphite fiber epoxy composites

Pinholes or other defect sites in a protective oxide coating provide pathways for atomic oxygen in low Earth orbit to reach underlying material. One concept of enhancing the lifetime of materials in low Earth orbit is to apply a leveling coating to the material prior to applying any reflective and protective coatings. Using a surface tension leveling coating concept, a low viscosity epoxy was applied to the surface of several composite coupons. A protective layer of 1000 A of SiO2 was deposited on top of the leveling coating, and the coupons were exposed to an atomic oxygen environment in a plasma asher. Pinhole populations per unit area were estimated by counting the number of undercut sites observed by scanning electron microscopy. Defect density values of 180,000 defects/sq cm were reduced to about 1000 defects/sq cm as a result of the applied leveling coating. These improvements occur at a mass penalty of about 2.5 mg/sq cm.

Jaworske, D. A.↗

Robotics

Earth's upper atmosphere is an extreme environment: dry, cold, and irradiated. It is unknown whether our aerobiosphere is limited to the transport of life, or there exist organisms that grow and reproduce while airborne (aerophiles); the microenvironments of suspended particles may harbor life at otherwise uninhabited altitudes[2]. The existence of aerophiles would significantly expand the range of planets considered candidates for life by, for example, including the cooler clouds of a hot Venus-like planet. The X project is an effort to engineer a robotic exploration and biosampling payload for a comprehensive survey of Earth's aerobiology. While many one-shot samples have been retrieved from above 15 km, their results are primarily qualitative; variations in method confound comparisons, leaving such major gaps in our knowledge of aerobiology as quantification of populations at different strata and relative species counts[1]. These challenges and X's preliminary solutions are explicated below. X's primary balloon payload is undergoing a series of calibrations before beginning flights in Spring 2012. A suborbital launch is currently planned for Summer 2012. A series of ground samples taken in Winter 2011 is being used to establish baseline counts and identify likely background contaminants.

Rothschild, Lynn J.↗

Genetic models in applied physiology: selected contribution: effects of spaceflight on immunity in the C57BL/6 mouse. I. Immune population distributions

There are several aspects of the spaceflight environment that may lead to changes in immunity: mission-related psychological stress, radiation, and changes in gravity. On December 5, 2001, the space shuttle Endeavor launched for a 12-day mission to examine these effects on C57BL/6 mice for the first time. On their return, assays were performed on the spleen, blood, and bone marrow. In response to flight, there were no significant differences in the general circulating leukocyte proportions. In contrast, there was an increase in splenic lymphocyte percentages, with a corresponding decrease in granulocytes. There was an overall shift in splenic lymphocytes away from T cells toward B cells, and a decrease in the CD4-to-CD8 ratios due to a decrease in T helpers. In contrast, there were proportional increases in bone marrow T cells, with decreases in B cells. Although the blast percentage and count were decreased in flight mice, the CD34(+) population was increased. The data were more consistent with a shift in bone marrow populations rather than a response to changes in the periphery. Many of the results are similar to those using other models. Clearly, spaceflight can influence immune parameters ranging from hematopoiesis to mature leukocyte mechanisms.

Non-NASA Center↗

Star counts and galactic structure

Star counts are discussed as an aid in studies of galactic structure. Iterative computations using a method-of-color-bins to match numerical models with observational data are described. The star counts provide bounds for the luminosity function and the color-magnitude diagram and allow spheroid normalization in a copycat Galaxy model which posits a galaxy with a Population I disk and a Population II spheroid. Good agreement has been obtained between star counts predicted by the model and observed distributions, including color and magnitude ranges and direction. Modifications being considered for the model include consideration of the halo, a galactic bulge and a thick disk. Several galactic structural features which have yet to be modeled and which may be tractable to the copycat model corrected with star counts are identified.

Bahcall, John N.↗

Application of Support Vector Regression to Derive Crater Depth/Diameter From Satellite Images

Through the study of impact crater shapes, one can draw important conclusions about the nature and evolution of planetary surfaces [e.g., 1-4].In particular, studying the depth (d) to diameter (D)ratio (d/D) of a population of impact craters, in combination with crater count statistics, can yield valuable insights regarding rates of erosion and burial[5]. Motivated by the great abundance of available planetary surface image data, the goal of this project is to develop an efficient way to estimate d/D from satellite images of impact craters for which stereo information is not available [6]. We set out to develop and train a machine learning algorithm to extract d/D from a dataset of synthetic impact crater images for which model d/D is known. The applications of machine learning to planetary science are numerous and diverse [7], including automatic planetary surface mapping [8] and the detection of impact craters [9]. Our algorithm makes use of Support Vector Regression (SVR), which is a type of Support Vector Machine (SVM) [10, 11].SVMs are a branch of supervised machine learning valued for their straightforward implementation and versatility in solving both classification and regression problems. In regression analysis, an SVR algorithm produces a hyperplane function to fit the training data points, as well as an ε-tube that surrounds the hyperplane. Tunable hyperparameters include the width of the ε-tube (ε) and the amount an algorithm is penalized for points which fall outside the ε-tube.

L R Chin↗

Deep galaxy count predictions in the radio, infrared, and X-ray spectral bands

The existence of a dominant population of strongly evolving starburst sources at moderate redshift is a plausible explanation for the excess number of faint blue galaxies detected in deep sky surveys. Multiwavelength observations at faint magnitudes would allow the existence of such a population to be confirmed. We use observed luminosity correlations and physical properties of known starburst galaxies to predict their contribution to the deep radio, infrared, and X-ray counts, as well as to the diffuse extragalactic background radiation in these various spectral bands.

Treyer, Marie-Agnes↗

Microfluidic Device

Described herein are particular embodiments relating to a microfluidic device that may be utilized for cell sensing, counting, and/or sorting. Particular aspects relate to a microfabricated device that is capable of differentiating single cell types from dense cell populations. One particular embodiment relates a device and methods of using the same for sensing, counting, and/or sorting leukocytes from whole, undiluted blood samples.

Tai, Yu-Chong↗

Microfluidic Device

Described herein are particular embodiments relating to a microfluidic device that may be utilized for cell sensing, counting, and/or sorting. Particular aspects relate to a microfabricated device that is capable of differentiating single cell types from dense cell populations. One particular embodiment relates a device and methods of using the same for sensing, counting, and/or sorting leukocytes from whole, undiluted blood samples.

Tai, Yu-Chong↗

Microfluidic Device

Described herein are particular embodiments relating to a microfluidic device that may be utilized for cell sensing, counting, and/or sorting. Particular aspects relate to a microfabricated device that is capable of differentiating single cell types from dense cell populations. One particular embodiment relates a device and methods of using the same for sensing, counting, and/or sorting leukocytes from whole, undiluted blood samples.

Tai, Yu-Chong↗

Microfluidic Device

Described herein are particular embodiments relating to a microfluidic device that may be utilized for cell sensing, counting, and/or sorting. Particular aspects relate to a microfabricated device that is capable of differentiating single cell types from dense cell populations. One particular embodiment relates a device and methods of using the same for sensing, counting, and/or sorting leukocytes from whole, undiluted blood samples.

Tai, Yu-Chong↗

Bolometric luminosity evolution

The observations made by IRAS are capable of detecting evolution in the OB star formation rates of galaxies at cosmologically interesting redshifts if that evolution takes the form of star formation rates ten or more times higher than seen in nearby galaxies. Spectroscopic follow-up observations of IRAS-selected galaxies, and IRAS source counts, indicate that there may indeed exist a rare population of galaxies with such high star formation rates. The most luminous found so far approach quasars in luminosity.

Lonsdale, Carol J.↗

Applications of chemiluminescence to bacterial analysis

Luminol chemiluminescence method for detecting bacteria was based on microbial activation of the oxidation of the luminol monoanion by hydrogen peroxide. Elimination of the prior lysing step, previously used in the chemiluminescence technique, was shown to improve considerably the reproducibility and accuracy of the method in addition to simplifying it. An inexpensive, portable photomultiplier detector was used to measure the maximum light intensity produced when the sample is added to the reagent. Studies of cooling tower water show that the luminol chemiluminescence technique can be used to monitor changes in viable cell population both under normal conditions and during chlorine treatment. Good correlation between chemiluminescence and plate counts was also obtained in the analysis of process water used in paper mills. This method showed good potential for monitoring the viable bacteria populations in activated sludge used in waste treatment plants to digest organic matter.

Searle, N. D.↗

An extended galactic population of low-luminosity x-ray sources (CVs?) and the diffuse x-ray background

The incompatibility of the properties of the X-ray background (XRB) with active galactic nuclei (AGNs) contributing approximately greater than 60% at energies of a few keV has often been interpreted as being due to a substantial contribution of a new population of yet unrecognized X-ray sources. The existence of such population has been recently suggested also by an analysis of very deep ROSAT observations which revealed a considerable excess of faint X-ray sources over that expected from QSO evolution models, and that the average spectrum of the resolved sources becomes harder with decreasing flux limit. These sources could be extragalactic in origin, but if they make a substantial contribution to the XRB then they must exhibit much weaker clustering than galaxies or QSOs in order to be consistent with the stringent constraints on source clustering imposed by autocorrelation analyses of the unresolved XRB. We investigate the possibility that the indicated new population of X-ray sources is Galactic in origin. Examining spherical halo and thick disk distributions, we derive the allowed properties of such populations which would resolve the discrepancy found in the number counts of faint sources and be consistent with observational constraints on the total background intensity, the XRB anisotropy, the number of unidentified bright sources, the Galaxy's total X-ray luminosity, and with the results of fluctuation analyses of the unresolved XRB. We find that a flattened Galactic halo (or a thick disk) distribution with a scale height of a few kpc is consistent with all the above requirements. The typical X-ray luminosity of the sources is approximately equal to 10(exp 30-31)ergs/s in the 0.5-2 keV band, the number density of sources in the solar vicinity is approximately 10(exp -4.5)pc(exp -3), their total number in the Galaxy is approximately 10(exp 8.5), and their total contribution to the Galaxy's X-ray luminosity is approximately 10(exp 39) ergs/s. We discuss the possible nature of these soures, including their being subdwarfs, low mass x-ray binaries (LMXBs), massive black holes, and old neutron stars. We argue that the inferred X-ray and optical luminosities of these sources, the slope of their energy spectrum, and the derived local number density and spatial distribution are all consistent with their being intrinsically faint cataclysmic variables with low accretion rates. We suggest a few possibilities for the origin of such population, including an origin from disrupted globular clusters or dark clusters. We make predictions and suggest tests that could either confirm or rule out our proposal in the near future.

Maoz, Eyal↗

Microbial assessment of cabin air quality on commercial airliners

The microbial burdens of 69 cabin air samples collected from commercial airliners were assessed via conventional culture-dependent, and molecular-based microbial enumeration assays. Cabin air samples from each of four separate flights aboard two different carriers were collected via air-impingement. Microbial enumeration techniques targeting DNA, ATP, and endotoxin were employed to estimate total microbial burden. The total viable microbial population ranged from 0 to 3.6 x10 4 cells per 100 liters of air, as assessed by the ATP-assay. When these same samples were plated on R2A minimal medium, anywhere from 2% to 80% of these viable populations were cultivable. Five of the 29 samples examined exhibited higher cultivable counts than ATP derived viable counts, perhaps a consequence of the dormant nature (and thus lower concentration of intracellular ATP) of cells inhabiting these air cabin samples. Ribosomal RNA gene sequence analysis showed these samples to consist of a moderately diverse group of bacteria, including human pathogens. Enumeration of ribosomal genes via quantitative-PCR indicated that population densities ranged from 5 x 10 1 ' to IO 7 cells per 100 liters of air. Each of the aforementioned strategies for assessing overall microbial burden has its strengths and weaknesses; this publication serves as a testament to the power of their use in concert.

microbe↗

Progress on Studies of Early Intense Cratering

The existence and effects of saturation cratering throughout the solar system was studied. It is found that saturation equilibrium cratering exists nowhere in the solar system, and that diameter distributions in even the most heavily cratered provinces reveal initial production functions related to impacting bodies. Different populations of impactors in different epochs and regions of the solar system are identified. The hypotheses are crucial for interpretation of planetary history. The crater counts on frontside lunar uplands, used as a basic reference curve identified with one of their populations of early impactors, are confirmed. This crater population is deficient in 1 to 16 km craters, which may be obliterated by the lavas. It is concluded that this curve is not representative of heavily cratered highlands, and is of questionable value as a standard comparison curve. The role of giant impacts during the intense early bombardment period was studied. Giant impact(s) on the primeval Earth may have initiated lunar formation.

Hartmann, W. K.↗

Osteogenic Transcription Regulated by Exaggerated Stretch Loading via Convergent Wnt Signaling

Cell and animal studies conducted onboard the International Space Station and formerly the Shuttle flights have provided data illuminating the deleterious biological response of bone to mechanical unloading. Down regulation of proliferative mechanisms within stem cell populations of the osteogenic niche is a suggested mechanism for loss of bone mass. However the intercellular communicative cues from osteoblasts and osteocytes in managing stem cell proliferation and osteogenic differentiation are largely unknown. In this investigation, MLO-Y4 osteocyte-like and MC3T3-E1 osteoblast-like cells, are co-culture under dynamic tensile conditions and evaluated for phenotypic expression of biochemical signaling proteins influential in driving stem cell differentiation. MLO-Y4 and MC3T3-E1 were co-cultured on polyethersulfone membrane with a 0.45m porosity to permit soluble factor transfer and direct cell-cell gap junction signaling. Cyclic tensile stimulation was applied for 48 h at a frequency of 0.1Hz and strain of 0.1. Total Live cell counts indicate mechanical activation of MC3T3-E1s inhibits proliferation while MLO-Y4s increase in number. However, the percent of live MLO-Y4s within the population is low (46.3 total count, *p0.05, n4) suggesting a potential apoptotic signaling cascade. Immunofluorescence demonstrated that stimulation of co-cultures elicits increased gap junction communication. Previously reported PCR evaluation of osteogenic markers further corroborate that the co-cultured populations communicative networks play a role in translating mechanical signals to molecular messaging. These findings suggest that an osteocyte-osteoblast signaling feedback mechanism may regulate mechanotransduction of an apoptotic cascade within osteocytes and transcription of cytokine signaling proteins responsible for stem cell niche recruitment much more directly than previously believed.

mechanical stimulation↗

Radio Sources in Galaxy Clusters at 28.5 GHz

We present serendipitous observations of radio sources at 28.5 GHz (1 cm), which resulted from our program to image thermal Sunyaev-Zeldovich (SZ) effect in 56 galaxy clusters. In a total area of about 0.8 degrees sq., we find 64 radio sources with fluxes down to - 0.4 mJy (> 4sigma,), and within 250" from the pointing centers. The spectral indices (S varies as v(sup -alpha) of 54 sources with published low frequency flux densities range from -0.6 approximately < alpha and alpha approximately < 2 with a mean of 0.77 +/- 0.06, and a median of 0.84. Extending low frequency surveys of radio sources towards galaxy clusters CL 0016+16, Abell 665, and Abell 2218 to 28.5 GHz, and selecting sources with S(sub l.4GHz) >/= 7 mJy to form an unbiased sample, we find a mean spectral index of 0.71 +/- 0.08 and a median of 0.71. We find 4 to 7 times more sources predicted from a low frequency survey in areas without galaxy clusters. This excess cannot be accounted for by gravitational lensing of a background radio population by cluster potentials, indicating most of the detected sources are associated with galaxy clusters. The differential source count slope, gamma is approximately 1.96 (dN/dS varies as S(exp -gamma)), is flatter than what is expected for a nonevolving Euclidean population (gamma = 2.5). For the cluster Abell 2218, the presence of unsubtracted radio sources with S(sub 28.5GHz) is approximately < 0.5 mJy (- 5 sigma), can only contribute to temperature fluctuations at a level of DeltaT is approximately 10 to 25 microK. The corresponding error due to radio point source contamination in the Hubble constant derived through a combined analysis of 28.5 GHz SZ images and X-ray emission observations ranges from 1% to 6%.

Cooray, Asantha R.↗

Timing of ancient extensional tectonic features on Mars

Although numerous studies have delineated the Tharsis and post-Tharsis volcanic/tectonic history on Mars, only a few attempts have examined the earlier epochs. This is not an easy task since unambiguous crater ages for pre-Tharsis and early Tharsis units are difficult to determine owing to a variety of active surface processes. Ancient tectonic features, however, have a sufficiently large superposed crater population that should permit relative dating. A technique for crater counting along linear features analagous to areal crater density is proposed. A modification of this approach has been tested and applied to a variety of ancient tectonic features.

Wichman, R.↗