Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “phosphazene”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Use of phosphoranimines to reduce organic carbonate content in Li-ion battery electrolytes

In this study, the use of phosphoranimines (PAs), a class of linear, monomeric phosphazenes, as electrolytes for Li-ion battery applications has been investigated as a route to improve safety and stability for Li-ion batteries. Of the potential PAs for use in battery applications, this work focuses on the initial synthetic preparation and analysis of N-trimethylsilyl-P,P-bis((2-methoxyethoxy)ethoxy)-P-ethylphosphoranimine (PA-5). PA-5 has high LiPF6 solubility in excess of 2 M, high thermal stability with a melting point below -80°C and high thermal stability as a neat compound to at least 250°C. As part of electrolyte blends, the inclusion of PA-5 shifts the onset of thermal degradation by close to 40°C at 35% loading and by 20°C at a 10% loading, improves the low temperature performance of the electrolyte, and when used as a primary solvent leads to increases in the flash point (by 20°C) when compared to more traditional EC:EMC blends. Cycling capabilities of full-coin cells with graphite negative electrodes and Li 1+w [Ni 0.5 Mn 0.3 Co 0.2 ] 1-w O 2 positive electrodes using PA-5:EC:EMC electrolyte blends are comparable with the performance seen for traditional EC:EMC blends. Analysis of the impact of the use of additives such as vinylene carbonate in PA-5:EC:EMC blended electrolyte results in enhanced capacity retention and improved coulombic efficiency.

25 ENERGY STORAGE↗

Techno-economic analysis of carbon dioxide capture from low concentration sources using membranes

Rising carbon dioxide (CO 2 ) levels in the atmosphere lead to global warming, causing climate change. As such, carbon capture has become necessary to slow the increase and reduce CO 2 levels in the atmosphere. Point source emissions have a wide range of CO 2 concentrations, but emissions below 3% CO 2 have mostly been ignored because Carbon capture from these sources has been viewed as costly and economically unsustainable. Membrane technologies are considered the most viable solution by virtue of more energy-efficient operation. Our group at Idaho National Laboratory (INL) has developed poly[bis((2-methoxyethoxy)ethoxy)phosphazene] (MEEP)-based carbon dioxide selective membranes with CO 2 /N 2 selectivity greater than 40 and CO 2 permeability greater than 450 Barrer. To understand the economics of carbon capture, a spreadsheet-based techno-economic analysis (TEA) model was developed to consider multiple parameters, including selectivity and permeability of the membranes, performance conditions such as the number of stages, module material, electricity price, membrane price, and capital financing. The cost of carbon capture in US $\$$/metric ton was calculated at various purities and compared with other membrane processes, cryogenic capture, solvent-based capture, and pressure swing adsorption-based capture. It was determined that a MEEP-based three-stage process had a capture cost of US $\$$ 50.1/metric ton for 99.8% purity CO 2 from a 1% CO 2 feed source in nitrogen (N 2 ). In conclusion, the capture cost using the best performing Pebax-based membrane was 464% higher, cryogenic capture was 60%–140% higher, pressure swing adsorption was 55%–165% higher, and chemical absorption was -10%–110% higher than MEEP-based membrane capture, respectively.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

A non-aqueous sodium hexafluorophosphate-based electrolyte degradation study: Formation and mitigation of hydrofluoric acid

Fundamental characterization of battery electrolyte is crucial for rechargeable batteries. This work reports the chemical stability of sodium hexafluorophosphate (NaPF6)-based non-aqueous electrolytes containing different solvent mixtures (e.g., cyclic and acyclic carbonates) in the presence of water for Na-ion batteries. A degradation study is conducted using NaPF 6 -based electrolytes, highlighting the effect of two electrolyte additives, 2,2,2-trifluoroethoxy-2,2,2-ethoxy phosphazene (FM2) and fluoroethylene carbonate (FEC), on degradation and cell performance of full-cell Na-ion batteries. Hydrolysis of this salt in acidic condition is particularly prone to form hydrofluoric acid (HF), and can be observed in electrolytes made with battery grade carbonate solvents (<20 ppm of water). Here, degradation mechanisms of NaPF 6 -based electrolytes are studied using liquid nuclear magnetic resonance (NMR). Noticeable degradation takes place in high purity electrolytes with the presence of moisture to form HF and organophosphates in timeframes below the current shelf-life of the Na electrolytes. FEC is not efficient to protect the electrodes from being exposed to HF. On the other hand, FM2 is revealed as a “scavenger” of HF, which helps stabilize the shelf life of electrolytes that might contain or become exposed to water. Our study underscores the importance to understanding the degradation of electrolyte and improving stability toward better shelf life for sodium ion batteries.

25 ENERGY STORAGE↗

Polyphosphazene polymer development for mixed matrix membranes using SIFSIX-Cu-2 i as performance enhancement filler particles

Phosphazene-based polymers were synthesized by using different pendant groups such as trifluoroethoxy (TFE), phenoxy (PHO) and octafluoropentoxy (OFP). High performance methoxyethoxyethoxy/cyclohexoxy (MEE/CH) based polyphosphazene was developed for the first time in literature using a mixed-substitution method. The structural, chemical, and thermal properties of these polymers were analyzed using several techniques such as Gel Permeation Chromatography (GPC), Thermal Gravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC), and Nuclear Magnetic Resonance (NMR). Significant differences in gas transport properties of gases have been observed between these pendant groups because of their differences in glass transition temperature and physical interaction with CO 2 . For the first time, we report on the high performance of TFE polyphophazene based mixed matrix membranes (MMMs) using a SIFSIX-Cu-2i (SIFSIX) metal organic framework (MOF) as the filler particles. These MMMs showed a significant improvement in both CO 2 permeability and CO 2 /N 2 selectivity compared to pure TFE polyphosphazene membranes. As a result, the excellent gas transport properties of these membranes make them very promising material for carbon capture applications.

36 MATERIALS SCIENCE↗

A Dual-Gated Structures for Lossless Ion Manipulations-Ion Mobility Orbitrap Mass Spectrometry Platform for Combined Ultra-High-Resolution Molecular Analysis

High-resolution ion mobility spectrometry-mass spectrometry (HR-IMS-MS) instruments have enormously advanced the ability to characterize complex biological mixtures. Unfortunately, HR-IMS and HR-MS measurements are typically performed independently due to mismatches in analysis time scales. Here we overcome this limitation by using a dual-gated ion injection approach to couple an 11-meter path length structures for lossless ion manipulations (SLIM) module to a Q-Exactive Plus Orbitrap MS. The dual-gate setup was implemented by placing one ion gate before the SLIM module and a second ion gate after. The dual-gated ion injection approach allowed the new SLIM-Orbitrap platform to simultaneously perform an 11-meter SLIM separation, Orbitrap mass analysis using the highest selectable mass resolution setting (up to 140k), and high-energy collision induced dissociation (HCD) in ~25 minutes over an $m/z$ range of ~1500 amu. The SLIM-Orbitrap was initially characterized using a mixture of standard phosphazene cations and demonstrated an average SLIM CCS resolving power (Rp CCS ) of ~218 and SLIM peak capacity of ~156 while simultaneously obtaining high mass resolutions. SLIM-Orbitrap analysis with fragmentation was then performed on mixtures of standard peptides and two reverse peptides (SDGRG 1+ , GRGDS 1+ , Rp CCS = 305) to demonstrate the utility of combined HR-IMS-MS/MS measurements for peptide identification. Our new HR-IMS-MS/MS capability was further demonstrated by analyzing a complex lipid mixture and showcasing SLIM separations on isobaric lipids. In conclusion, this new SLIM-Orbitrap platform demonstrates a critical new capability for proteomics and lipidomics applications, and the high-resolution multimodal data obtainable with this system establishes the foundation for reference-free identification of unknown ion structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Mobility Selective Ion Soft-Landing and Characterization Enabled Using Structures for Lossless Ion Manipulation

In this study, while conventional ion-soft landing uses the mass-to-charge (m/z) ratio to achieve molecular selection for deposition, here we demonstrate the use of Structures for Lossless Ion Manipulation (SLIM) for mobility-based ion selection and deposition. The dynamic rerouting capabilities of SLIM were leveraged to enable the rerouting of a selected range of mobilities to a different SLIM path (rather than MS) that terminated at a deposition surface. A selected mobility range from a phosphazene ion mixture was rerouted and deposited with a current pulse (~150 pA) resembling its mobility peak. In addition, from a mixture of tetra-alkyl ammonium (TAA) ions containing chain lengths of C5–C8, selected chains (C6, C7) were collected on a surface, reconstituted into solution-phase, and subsequently analyzed with a SLIM-qToF to obtain an IMS/MS spectrum, confirming the identity of the selected species. Further, this method was used to characterize triply charged tungsten-polyoxometalate anions, PW 12 O 40 3– (WPOM). The arrival time distribution of the IMS/MS showed multiple peaks associated with the triply charged anion (PW 12 O 40 3– ), of which a selected ATD was deposited and imaged using TEM. Additionally, the identity of the deposited WPOM was ascertained using energy-dispersive (EDS) spectroscopy. Further, we present theory and computations that reveal ion landing energies, the ability to modulate the energies, and deposition spot sizes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Cyclable Variable Path Length Multilevel Structures for Lossless Ion Manipulations (SLIM) Platform for Enhanced Ion Mobility Separations

Ion mobility-mass spectrometry (IMS-MS) is increasingly used to analyze complex samples and provide structural information of unknown compounds. As the complexity of samples increases, there is a need to improve the resolution of IMS-MS instruments to increase the rate of molecular identification. In this work, we evaluated a cyclable and variable-pathlength multilevel Structures for Lossless Ion Manipulations (SLIM) platform to achieve a higher resolving power than previously possible. This new multilevel SLIM platform has eight separation levels connected by ion escalators and a path length of ~88 meters (~11 meters per level). Our new multilevel SLIM can also be operated in an ‘ion cycling’ mode where a set of return ion escalators transport ions from the eighth back to the first level, allowing even longer path lengths (and higher IMS resolution). The platform has been improved to enhance the ion transmission and IMS separation quality by reducing the spacing between SLIM boards as well as board thickness, reducing the ions’ escalator residence time. Compared to the previous generation, the new multilevel SLIM demonstrated a better transmission for a set of phosphazene ions, especially for the low-mobility ions. The new multilevel SLIM achieved better resolving powers than our previous 4-level SLIM. The collision cross-section-based resolving power of the SLIM platform was tested using a pair of singly-charged reverse sequence peptides (SDGRG 1+ , GRGDS 1+ ). We achieved 1100 resolving power using 88 meters of path length (i.e., 8 levels) and 1400 following an additional pass through the eight levels (i.e., 16 levels or 173.5 m). The multilevel SLIM was further evaluated to demonstrate the enhanced separation for a positively and negatively charged brain total lipid extract sample. Finally, the new multilevel SLIM enables much higher resolving powers for a wide range of ion mobilities, improved transmission for low-mobility ions, and the ability to perform even higher resolving power for ions of interest.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrocatalytic Alcohol Oxidation with Iron-Based Acceptorless Alcohol Dehydrogenation Catalyst

Electrochemical and chemical studies reveal that the amido complex (PNH x P)Fe(CO)(H)(X) (FeN 1, x = 0, X = 0; Fe(H)(NH) 2, x = 1, X = H; PNHP = bis[2-(diisopropylphosphino)ethyl]amine) is active for the electrocatalytic oxidation of isopropanol. At room temperature, the amido FeN 1 dehydrogenates isopropanol to form acetone. The resulting amino hydride complex Fe(H)(NH) 2 is subsequently oxidized by one electron at a low potential (–0.74 V versus ferrocene/ferrocenium, Fc o/+ ) in tetrahydrofuran. In the presence of strong base (phosphazene base P 2 -Et, Et-N = P 2 (dma) 5 , P2), this oxidation process becomes a two-electron, two-proton process that regenerates FeN 1. FeN 1 is active for the electrooxidation of isopropanol in the presence of strong base (i.e., P2) with an onset potential near –1 V versus Fc o/+ . By cyclic voltammetry, fast turnover frequencies of 1.7 s –1 for isopropanol oxidation are achieved with FeN 1. Lastly, controlled potential electrolysis studies confirm that the product of isopropanol electrooxidation is acetone, generated with high Faradaic efficiency (~100%).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Cyclopropenimine superbases: Competitive initiation processes in lactide polymerization

Cyclopropenimine superbases were employed in this study to catalyze the ring-opening polymerization of lactide. Polymerization occurred readily in the presence and absence of alcohol initiators. Polymerizations in the absence of alcohol initiators revealed a competitive initiation mechanism involving deprotonation of lactide by the cyclopropenimine to generate an enolate. NMR and MALDI-TOF analysis of the poly(lactides) generated from cyclopropenimines in the absence of alcohol initiators showed acylated lactide and hydroxyl end groups. Finally, model studies and comparative experiments with guanidine and phosphazene catalysts revealed the subtle influence of the nature of the superbase on competitive initiation processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ultrastable Superbase-Derived Protic Ionic Liquids

Protic ionic liquids are synthesized via proton transfer from acids to organic bases. One of the key issues associated with conventional protic ionic liquids is the thermal instability resulting from temperature-induced decomposition via reverse proton transfer. This shortcoming significantly hampers the use of these protic ionic liquids in separations, electrochemical capacitors, fuel cells, and so forth. Herein we show that it is possible to prepare protic ionic liquids with thermal stabilities approaching those of common aprotic ionic liquids. Our new class of protic ionic liquids, derived via integrated neutralization and metathesis of superbasic phosphazenes or guanidines, exhibits exceptionally low vapor pressures at 150 °C while being stable to strong alkali agents such as aqueous KOH, suggesting potential in energy-related applications, including electrochemical capacitors and PEM-type fuel cells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hexakis(4-phormylphenoxy)cyclotriphosphazene: X-ray and DFT-calculated structures

The crystal structure of hexakis(4-phormylphenoxy)cyclotriphosphazene is determined by using X-ray diffraction and then the molecular structure is investigated with density functional theory (DFT). X-Ray study shows that the title compound has C-H-{pi} interaction with phosphazene ring. The molecules in the unit cell are packed with Van der Waals and dipole-dipole interactions and the molecules are packed in zigzag shaped. Optimized molecular geometry is calculated with DFT at B3LYP/6-311G(d,p) level. The results from both experimental and theoretical calculations are compared in this study.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Life Cycle Assessment of Innovative Carbon Dioxide Selective Membranes from Low Carbon Emission Sources: A Comparative Study

Carbon capture has been an important topic of the twenty-first century because of the elevating carbon dioxide (CO2) levels in the atmosphere. CO2 in the atmosphere is above 420 parts per million (ppm) as of 2022, 70 ppm higher than 50 years ago. Carbon capture research and development has mostly been centered around higher concentration flue gas streams. For example, flue gas streams from steel and cement industries have been largely ignored due to lower associated CO2 concentrations and higher capture and processing costs. Capture technologies such as solvent-based, adsorption-based, cryogenic distillation, and pressure-swing adsorption are under research, but many suffer from higher costs and life cycle impacts. Membrane-based capture processes are considered cost-effective and environmentally friendly alternatives. Over the past three decades, our research group at Idaho National Laboratory has led the development of several polyphosphazene polymer chemistries and has demonstrated their selectivity for CO2 over nitrogen (N2). Poly[bis((2-methoxyethoxy)ethoxy)phosphazene] (MEEP) has shown the highest selectivity. A comprehensive life cycle assessment (LCA) was performed to determine the life cycle feasibility of the MEEP polymer material compared to other CO2-selective membranes and separation processes. The MEEP-based membrane processes emit at least 42% less equivalent CO2 than Pebax-based membrane processes. Similarly, MEEP-based membrane processes produce 34–72% less CO2 than conventional separation processes. In all studied categories, MEEP-based membranes report lower emissions than Pebax-based membranes and conventional separation processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Flame retardant polyphosphazenes

Three processes for the preparation of polyphosphazenes were investigated: (1) the reaction of bisphosphines with diazides, (2) the condensation of bisdichlorophosphoranes with diamines; and (3) the treatment of bisphosphines with diamines in the presence of carbon tetrachloride followed by base dehydrohalogenation. All products obtained were of low molecular weight; the degree of polymerization did not exceed twelve repeating units. However, several compositions exhibited good thermal stability. No weight loss was observed up to 390 C when heated in air at 5 C/min. Treatment of bisphosphines with either an excess of a diazide or an excess of a diamine in the presence of carbon tetrachloride resulted in the production of difunctional phosphazenes which were respectively, azido and amino terminated. The reaction of these azido terminated extended monomers with bisphosphines did not produce high molecular weight materials. The bis-aminophosphazene prepared for the first time under this contract was successfully incorporated into a polyimide.

Paciorek, K. L.↗

Preparation of linear hydroxy substituted polyphosphazenes

The synthesis of partially hydroxy-substituted phosphazene prepolymers amenable to processing into cellular, flexible polyurethane foams was investigated. Factors determined include (1) the environment of the hydroxyl group; (2) the ease of the hexachlorocyclotriphosphazene polymerization; (3) the nature of the nonreactive substituents; and (4) the mode of introduction of the hydroxyl entity. The specific approaches taken, the rationale of the selections made, and the results are discussed.

Paciorek, K. L.↗

Compound oxidized styrylphosphine

A process is described for preparing flame resistant, nontoxic vinyl polymers which contain phosphazene groups and which do not emit any toxic or corrosive products when they are oxidatively degraded. Homopolymers, copolymers, and terpolymers of a styrene based monomer are prepared by polymerizing at least one oxidized styrylphosphine monomer from a group of organic azides, or by polymerizing p-diphenylphosphinestyrene and then oxidizing that monomer with an organoazide from the group of (C6H5)2P(O)N3, (C6H5O)2P(O)N3, (C6H5)2C3N3(N3), and C6H5C3N3(N3)2. Copolymers can also be prepared by copolymerizing styrene with at least one oxidized styrylphosphine monomer.

Paciorek, K. J. L.↗

Heat resistant polymers of oxidized styrylphosphine

A flame resistant, nontoxic polymer which may be used safely in confined locations where there is inadequate ventilation is prepared either by polymerizing compounds having the formula R-N=P(C6H5)2(C6H4)CH=CH2 where R is an organic moeity selected from the group of (C6H5)2P(O)-, (C6H5O)2P(O)-, (C6H5)2 C3N3-, or their mixtures, or by reacting a polymer with an organic azide such as diphenylphosphinylazide, diphenyl-phosphorylazide, 2-azido-4,6-diphenly-5-triazine, 2,4-diazido-6-phenyl-s-triazine, trimethylsilyoazide, triphenylsilylazine, and phenylazine. The reaction of the styrylphosphine with the organozaide results in the oxidation of the trivalent phosphorus atom to the pentavalent state in the form of an unsaturated P=N linkage known as a phosphazene group.

Paciorek, K. J. L.↗

Fire- and heat-resistant laminating resins based on maleimido-substituted aromatic cyclotriphosphazenes

A novel class of flame- and heat-resistant polymers has been synthesized by the thermal polymerization of maleimido-substituted aromatic cyclotriphosphazenes. The polymer obtained from tris-(aminophenoxy)tris(maleimidophenoxy)cyclotriphosphazene has good thermal stability and is noteworthy for its high char yield, viz., 82 percent at 800 C in nitrogen and 81 percent at 700 C in air. Graphite-fabric laminates prepared with this polymer did not burn in pure oxygen, even at 300 C, and were tested for mechanical properties. Hexakis(4-maleimidophenoxy)cyclotriphosphazene and some fluorine-containing monomers have also been synthesized. The structures of these cyclic phosphazene precursors and polymers were characterized by FT IR spectrophotometry, H-1 NMR, F-19 NMR, and P-31 solid-state magic angle spinning NMR spectroscopy, and mass spectrometry. The curing behavior of the polymer precursors and the thermal stabilities of the polymers were evaluated by differential scanning calorimetry (DSC) and thermogravimetric analyses (TGA).

Kumar, D.↗

Isomeric Trisaryloxycyclotriphosphazene Polymer Precursors

Substances useful for making heat-and fire-resistant polymers. Cyclotriphosphazene-based monomers and polymer precursors led to development of high-temperature materials. Cyclotriphosphazene-derived monomers, polymer precursors, and polymers becoming important from both industrial and scientific points of view. Presence of phosphazene moiety in cyclotriphosphazene-based monomers and polymer precursors expected to impact special properties in desired high-performance materials containing inorganic backbones for aerospace applications. Useful for obtaining heat-and fire-resistant polymers for composites, adhesives, molding powders, and coating laminates. Also used in structures (e.g. secondary structures in aircraft), in construction of spacecraft, and in electronics and computer industries.

St. Clair, Terry L.↗