Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “perfect wall”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Improved Crystal Quality by Detached Solidification in Microgravity

Directional solidification in microgravity has often led to ingots that grew with little or no contact with the ampoule wall. When this occurred, crystallographic perfection was usually greatly improved -- often by several orders of magnitude. Unfortunately, until recently the true mechanisms underlying detached solidification were unknown. As a consequence, flight experiments yielded erratic results. Within the past four years, we have developed a new theoretical model that explains many of the flight results. This model gives rise to predictions of the conditions required to yield detached solidification, both in microgravity and on earth. A discussion of models of detachment, the meniscus models and results of theoretical modeling, and future plans are presented.

Regel, Liya L.↗
NASA NTRS1983

Viscous shock-layer predictions of three-dimensional nonequilibrium flows past the space shuttle at high angle of attack

Computational solutions were obtained for chemically reacting flowfields over the entire windward surface of the Space Shuttle at high angle of attack. The recently developed computational method for the Space Shuttle is capable of treating three dimensional viscous nonequilibrium air flow as well as equilibrium air and perfect gas flows. A general nonorthogonal computational grid system is used to treat the nonaxisymmetric geometry. Boundary conditions take into account noncatalytic wall, equilibrium with noncatalytic wall condition are compared to the fully catalytic wall solutions, the equilibrium air solutions, the perfect gas solutions, and also the Shuttle flight heating and pressure data. The comparisons show good agreement and correlations in most cases.

Kim, M. D.↗
NASA NTRS2003

Residual Gas Effects on Detached Solidification in Microgravity

Many microgravity directional solidification experiments yielded ingots with portions that grew without contacting the ampoule wall, leading to greatly improved crystallographic perfection. Our long-term goal is to make such detached solidification reproducible, which requires a full understanding of the mechanisms underlying it. Our Moving Meniscus Model of steady-state detachment predicts that it depends strongly on the surface tension of the melt and the advancing contact angle with the ampoule wall. Detached solidification is more likely when the contact angle for the melt on the ampoule wall is high, i.e. non-wetting. It has been claimed that impurities increase the contact angle. The objective of the current project is to determine the influence of residual gases on the surface tension and contact angle of molten semiconductors on typical ampoule materials. We are focusing on determining the influence of oxygen on the contact angle of molten InSb on clean silica ('quartz'), including the advancing and retreating contact angles in addition to the usual equilibrium contact angle. We have created a gas flow system that allows us to control the oxygen partial pressure over a sessile drop of InSb on a horizontal quartz surface. The cell is slowly tilted while videotaping to reveal the contact angles on the two sides of the drop just prior to it rolling down the surface. Thus far, we have learned the following: (1) Molten InSb readily forms an oxide layer in the presence of the trace amounts of oxygen found in high purity argon; (2) This oxide contains a substantial amount of Ga, which presumably is a trace contaminant that is not detectable in the starting material; (3) The addition of 10% hydrogen to the argon gas is sufficient to reduce the oxide and produce a clean drop; (4) An infrared filter must precede the video camera in order to produce a sharp image of the drop for later image analysis; (5) Tilting the surface on which the drop rests causes the two sides of the drop to display different contact angles, reflecting contact line sticking; (6) Vibration strongly accelerates the approach of the drop to its final shape on a horizontal surface by helping to overcome sticking of the contact line; (7) Oscillation of the drop surface due to vibration appears to increase as the surface is inclined from horizontal. Presumably, the angle at which the drop rolls down the surface is also reduced by vibration. This observation is particularly significant, as the meniscus must move along the ampoule wall during detached solidification.

Regel, Liya L.↗
NASA NTRS2003

Improved Crystal Quality By Detached Solidification in Microgravity

Many microgravity directional solidification experiments yielded ingots with portions that grew without contacting the ampoule wall, leading to greatly improved crystallographic perfection. Our long term goals have been: (1) To develop a complete understanding of all of the phenomena of detached solidification.; (2) To make it possible to achieve detached solidification reproducibly; (3) To increase crystallographic perfection through detached solidification. We have three major achievements to report here: (1) We obtained a new material balance solution for the Moving Meniscus Model of detached solidification. This solution greatly clarifies the physics as well as the roles of the parameters in the system; (2) We achieved detached solidification of InSb growing on earth in BN-coated ampoules; (3) We performed an extensive series of experiments on freezing water that showed how to form multiple gas bubbles or tubes on the ampoule wall. However, these did not propagate around the wall and lead to fully detached solidification unless the ampoule wall was extremely rough and non-wetted.

Regel, Liya L.↗
NASA NTRSDate not supplied

Framework for Analyzing the Complex Interactions Between Spacecraft Motion and Slosh Dynamics in Low-G Environments

The fuel-to-dry-mass ratio of spacecraft continues to grow as new human spaceflight missions target destinations from Earth. Large amounts of liquid propellant can lead to significant coupling between the rigid-body dynamics of the spacecraft and the motion of the fuel within its storage tank. The present work gives an overview of the dynamic features and a flowchart for a method of simulating the motion of a spacecraft with fuel slosh inside a cylindrical, domed tank in a low-g environment. The method involves modeling the liquid propellant as a particle that transfers momentum to the spacecraft through perfectly inelastic collisions with the tank wall. The foundation of the modeling methodology is the approach taken during the Apollo program used to predict the effect of fuel slosh on the complex motion exhibited by the Service Module following separation from the Crew Module. This paper discusses the motivation, methodology, and conclusions from the Apollo-era method, and subsequently builds upon it by incorporating corrections to the derivation of the dynamics and filling in the gaps due to unavailability of the detailed contractor report and simulation code. The results presented in this paper provide an example that demonstrates the effect that fuel slosh can have on the trajectory of a spacecraft in a low-g environment.

William J Elke III↗
NASA NTRSDate not supplied

Framework for Analyzing the Complex Interactions Between Spacecraft Motion and Slosh Dynamics in Low-G Environments

The fuel-to-dry-mass ratio of spacecraft continues to grow as new human spaceflight missions target destinations farther from Earth. Large amounts of liquid propellant can lead to significant coupling between the rigid-body dynamics of the spacecraft and the motion of the fuel within its storage tank. The present work gives an overview of the dynamic features and a flowchart for a method of simulating the motion of a spacecraft with fuel slosh inside a cylindrical, domed tank in a low-g environment. The method involves modeling the liquid propellant as a particle that transfers momentum to the spacecraft through perfectly inelastic collisions with the tank wall. The foundation of the modeling methodology is the approach taken during the Apollo program used to predict the effect of fuel slosh on the complex motion exhibited by the Service Module following separation from the Command Module. This paper discusses the motivation, methodology, and conclusions from the Apollo-era method, then presents corrections to the derivation of the dynamics and fills in the gaps left from the unavailability of the detailed contractor report and simulation code. The results presented in this paper provide an example that demonstrates the effect that fuel slosh can have on the trajectory of a spacecraft in a low-g environment.

William J Elke III↗
NASA NTRS2024

Test and Analysis of the 8-foot Diameter Cylindrical Sandwich Composite Test Article CTA8.2B: As part of the NASA Engineering and Safety Center Shell Buckling Knockdown Factor Project

The buckling response of thin-walled cylindrical structures have long been shown to be sensitive to various imperfections. That is, imperfections related to load introduction, boundary conditions, material property variation, and geometric deviations can all contribute to experimentally obtained buckling loads being lower than the buckling loads predicted for perfect representations of the same thin-walled cylindrical structure. To account for the influence of geometry-based imperfections of a thin-walled cylindrical structure on buckling response, a design factor (also known as a buckling knockdown factor) is used during the design phase. Guidelines for buckling knockdown factors are readily available in NASA SP-8007, Buckling of Thin Walled Circular Cylinders, which was updated in 2020. Prior to this recent update, NASA SP-8007 had not been updated since 1969, and since that time, computational analysis, experimental testing, and manufacturing methods have significantly improved. The NASA Engineering and Safety Center (NESC) Shell Buckling Knockdown Factor Project (SBKF, NESC Assessment 07-010-E) had the goal of developing buckling design recommendations for select classes of metallic and composite launch-vehicle structures [3]. Specifically, the test and analysis results from the fourth SBKF composite test article SBKF-P3-CYL-CTA8.2B, which is referred to as CTA8.2B, are described in this paper. This test was the fourth in a series of four tests on sandwich composite cylinders that will be used to experimentally validate analysis methods, which in turn can be used to develop new analysis-based shell buckling design guidelines for typical sandwich composite launch vehicle cylindrical structures. Publications describing previous test validation with analysis are available in Refs. CTA8.2B was designed to occupy one corner of the design space with approximately equal bending stiffnesses in the axial and transverse directions and have a larger ratio of radius to effective shell thickness. Each test article had a unique design and was designed to occupy a specific region of the design space. CTA8.2B was an 8-foot diameter honeycomb-core sandwich cylinder that was fabricated and tested at the NASA Marshall Space Flight Center (MSFC). The primary objectives of this test were to interrogate the structural capability of a composite test article, and to verify the test article design and analysis approach for cylinders subjected to axial compression and combined axial and bending loads. First, descriptions of the test article design and test are given in Section 2.0, and modeling and analysis methods used in support of the test article design and testing activities are described briefly in Section 3.0. Then, select test results are presented and compared to predicted results in Section 4.0, and concluding remarks are presented in Section 5.0. Finally, drawings of CTA8.2B and references used to support the test and analysis are provided in the Appendix.

Nonlinear analysis↗
NASA NTRS1985

Analysis of the electromagnetic scattering from an inlet geometry with lossy walls

One of the primary goals is to develop an approximate but sufficiently accurate analysis for the problem of electromagnetic (EM) plane wave scattering by an open ended, perfectly-conducting, semi-infinite hollow circular waveguide (or duct) with a thin, uniform layer of lossy or absorbing material on its inner wall, and with a simple termination inside. The less difficult but useful problem of the EM scattering by a two-dimensional (2-D), semi-infinite parallel plate waveguide with an impedance boundary condition on the inner walls was chosen initially for analysis. The impedance boundary condition in this problem serves to model a thin layer of lossy dielectric/ferrite coating on the otherwise perfectly-conducting interior waveguide walls. An approximate but efficient and accurate ray solution was obtained recently. That solution is presently being extended to the case of a moderately thick dielectric/ferrite coating on the walls so as to be valid for situations where the impedance boundary condition may not remain sufficiently accurate.

Myung, N. H.↗
NASA NTRS1974

Effect of geometrical and flow parameters on high-effectiveness region of film cooling

Previous analyses for an inviscid jet injected into a stream and the turbulent mixing region which forms between jet and stream are used to find the extent of the core region in a cooling film by calculating the growth of the turbulent boundary layer on the downstream wall. The core is a region of nearly perfect effectiveness which ends at the intersection of the boundary layer and the mixing region. The calculations show that the most important geometrical factor bearing on the length of the core is the curvature of the wall. When the radius of curvature is large, the boundary layer remains thin and the core is long. The effects of Reynolds number, total-pressure difference between film and stream, and lateral position of the downstream wall are also investigated. The step configuration is shown to have a longer core than the slot for the same flow conditions.

Braum, W. H.↗
NASA NTRS1981

GTD analysis of airborne antennas radiating in the presence of lossy dielectric layers

The patterns of monopole or aperture antennas mounted on a perfectly conducting convex surface radiating in the presence of a dielectric or metal plate are computed. The geometrical theory of diffraction is used to analyze the radiating system and extended here to include diffraction by flat dielectric slabs. Modified edge diffraction coefficients valid for wedges whose walls are lossy or lossless thin dielectric or perfectly conducting plates are developed. The width of the dielectric plates cannot exceed a quarter of a wavelength in free space, and the interior angle of the wedge is assumed to be close to 0 deg or 180 deg. Systematic methods for computing the individual components of the total high frequency field are discussed. The accuracy of the solutions is demonstrated by comparisons with measured results, where a 2 lambda by 4 lambda prolate spheroid is used as the convex surface. A jump or kink appears in the calculated pattern when higher order terms that are important are not included in the final solution. The most immediate application of the results presented here is in the modelling of structures such as aircraft which are composed of nonmetallic parts that play a significant role in the pattern.

Rojas-Teran, R. G.↗
NASA NTRS1992

BLSTA: A boundary layer code for stability analysis

A computer program is developed to solve the compressible, laminar boundary-layer equations for two-dimensional flow, axisymmetric flow, and quasi-three-dimensional flows including the flow along the plane of symmetry, flow along the leading-edge attachment line, and swept-wing flows with a conical flow approximation. The finite-difference numerical procedure used to solve the governing equations is second-order accurate. The flow over a wide range of speed, from subsonic to hypersonic speed with perfect gas assumption, can be calculated. Various wall boundary conditions, such as wall suction or blowing and hot or cold walls, can be applied. The results indicate that this boundary-layer code gives velocity and temperature profiles which are accurate, smooth, and continuous through the first and second normal derivatives. The code presented herein can be coupled with a stability analysis code and used to predict the onset of the boundary-layer transition which enables the assessment of the laminar flow control techniques. A user's manual is also included.

Wie, Yong-Sun↗
NASA NTRS1994

Analysis of cold worked holes for structural life extension

Cold working holes for improved fatigue life of fastener holes are widely used on aircraft. This paper presents methods used by the authors to determine the percent of cold working to be applied and to analyze fatigue crack growth of cold worked fastener holes. An elastic, perfectly-plastic analysis of a thick-walled tube is used to determine the stress field during the cold working process and the residual stress field after the process is completed. The results of the elastic/plastic analysis are used to determine the amount of cold working to apply to a hole. The residual stress field is then used to perform damage tolerance analysis of a crack growing out of a cold worked fastener hole. This analysis method is easily implemented in existing crack growth computer codes so that the cold worked holes can be used to extend the structural life of aircraft. Analytical results are compared to test data where appropriate.

Wieland, David H.↗
NASA NTRS1993

Supersonic minimum length nozzle design for dense gases

Recently, dense gases have been investigated for many engineering applications such as for turbomachinery and wind tunnels. Supersonic nozzle design for these gases is complicated by their nonclassical behavior in the transonic flow regime. In this paper a method of characteristics (MOC) is developed for two-dimensional (planar) and, primarily, axisymmetric flow of a van der Waals gas. Using a straight aortic line assumption, a centered expansion is used to generate an inviscid wall contour of minimum length. The van der Waals results are compared to previous perfect gas results to show the real gas effects on the flow properties and inviscid wall contours.

Aldo, Andrew C.↗
NASA NTRS2003

Sound Propagation from a Supersonic Jet Flowing through a Rigid-walled Duct with a J-Deflector

An experimental study is performed on the acoustical characteristics of a scale-model, perfectly expanded, cold supersonic jet of gaseous nitrogen (Mach 2.5, nozzle exit diameter of 1 inch) flowing through a rigid-walled duct having an upstream J-deflector. The nozzle is mounted vertically, with the nozzle exit plane at a height of 73 jet diameters above ground level. Relative to the nozzle exit plane, the location of the duct inlet is varied at 10, 5, and -1 jet diameters. Far-field sound pressure levels were obtained at 2 levels (54 jet diameters and 10 jet diameters above ground) with the aid of 9 acoustic sensors equally spaced around a circular arc of radius equal to 80 jet diameters. Comparisons of the acoustic field were made with and without the duct.

Kandula, Max↗
DOE OSTI2024

Wall modes and the transition to bulk convection in rotating Rayleigh-Bénard convection

We investigate states of rapidly rotating Rayleigh-Bénard convection in a cylindrical cell over a range of Rayleigh numbers 3 × 10 5 ≤ Ra ≤ 5 × 10 9 and Ekman numbers 10 − 6 ≤ Ek ≤ 10 − 4 for Prandtl number Pr = 0.8 and aspect ratios 1 / 5 ≤ Γ ≤ 5 using direct numerical simulations. We characterize, for perfectly insulating sidewall boundary conditions, the first transition to convection via wall mode instability and the nonlinear growth and instability of the resulting wall mode states, including a secondary transition to time dependence. We show how the radial structure of the vertical velocity u z and the temperature T is captured well by the linear eigenfunctions of the wall mode instability where the radial width of u z is δ u z ∼ Ek 1 / 3 r / H whereas δ T ∼ e − k r ( k is the wave number of a laterally infinite wall mode state). The disparity in spatial scales for Ek = 10 − 6 means that the heat transport is dominated by the radial structure of u z since T varies slowly over the radial scale δ u z . We further describe how the transition to a state of bulk convection is influenced by the presence of the wall mode states. We use temporal and spatial scales as measures of the local state of convection and the Nusselt number Nu as representative of global transport. Our results elucidate the evolution of the wall state of rotating convection and confirm that wall modes are strongly linked with the boundary zonal flow being the robust remnant of nonlinear wall mode states. We also show how the heat transport ( Nu ) contributions of wall modes and bulk modes are related and discuss approaches to disentangling their relative contributions. Published by the American Physical Society 2024

58 GEOSCIENCES↗
DOE OSTI2025

Outflow Boundary Conditions for Turbine-Integrated Rotating Detonation Combustors

This study examines outflow boundary conditions (BCs) in computational fluid dynamics (CFD) simulations of a transition duct with and without guide vanes that converts supersonic flow exiting a rotating detonation combustor (RDC) to subsonic flow to drive a turbine. Since the flow exiting the transition duct has swirling shock waves with significant spatial and temporal variations in pressure, temperature, and Mach number, imposing proper BCs poses a challenge. To ensure all swirling shock waves exit the transition duct without creating non-physical reflected waves at its outlet, this study examined three outflow BCs: (1) the average pressure imposed at the duct’s outlet, (2) a nonreflecting BC (NRBC) with a specified average pressure imposed at the duct’s outlet, (3) the average pressure imposed at the outlet of an extension duct made up of a buffer layer and a sponge layer. This study is based on the three-dimensional, unsteady density-weighted-ensemble-averaged continuity, Navier–Stokes, and energy equations for a thermally perfect gas closed by the realizable k–ε model and “enhanced” wall functions. The results obtained show that imposing an average pressure at the transition duct’s outlet produces spurious waves that degrade the physical meaningfulness of the solution. When the NRBC was applied, swirling shock waves exited the duct’s outlet without creating spurious waves. However, its usage requires the gas to be thermally, as well as calorically, perfect, which this study shows could be a concern. By imposing the average pressure at the outlet of an extension duct, the gas does not need to be calorically perfect. The results obtained show the effects of the sponge layer’s length and coarsening ratio on damping nonuniformities in non-physical reflected waves to ensure the flow exiting the transition duct’s outlet can do so as if there are no boundaries present and has the desired average pressure—even though the BC is applied at the extension duct’s outlet.

gas turbines↗
NASA NTRS1989

Parametric study of electromagnetic waves propagating in absorbing curved S ducts

A finite-element Galerkin formulation has been developed to study attenuation of transverse magnetic (TM) waves propagating in two-dimensional S-curved ducts with absorbing walls. In the frequency range where the duct diameter and electromagnetic wave length are nearly equal, the effect of duct length, curvature (duct offset), and absorber wall thickness was examined. For a given offset in the curved duct, the length of the S-duct was found to significantly affect both the absorptive and reflective characteristics of the duct. For a straight and a curved duct with perfect electric conductor terminations, power attenuation contours were examined to determine electromagnetic wall properties associated with maximum input signal absorption. Offset of the S-duct was found to significantly affect the value of the wall permittivity associated with the optimal attenuation of the incident electromagnetic wave.

Baumeister, Kenneth J.↗
DOE OSTI2024

CFT and lattice correlators near an RG domain wall between minimal models

Conformal interfaces separating two conformal field theories (CFTs) provide maps between different CFTs, and naturally exist in nature as domain walls between different phases. One particularly interesting construction of a conformal interface is the renormalization group (RG) domain wall between CFTs. For a given Virasoro minimal model \mathcal{M}_{k+3,k+2} ℳ k + 3 , k + 2 , an RG domain wall can be generated by a specific deformation which triggers an RG flow towards its adjacent Virasoro minimal model \mathcal{M}_{k+2,k+1} ℳ k + 2 , k + 1 with the deformation turned on over part of the space. An algebraic construction of this domain wall was proposed by Gaiotto in [J. High Energy Phys. 12, 103 (2012)]. In this paper, we will provide a study of this RG domain wall for the minimal case k=2 k = 2 , which can be thought of as a nonperturbative check of the construction. In this case the wall is separating the Tricritical Ising Model (TIM) CFT and the Ising Model (IM) CFT. We will check the analytical results of correlation functions from the RG brane construction with the numerical density matrix renormalization group (DMRG) calculation using a lattice model proposed in [arXiv.1206.1332, Science 344, 280 (2014)], and find a perfect agreement. We comment on possible experimental realizations of this RG domain wall.

Cogburn, Cameron V.↗