Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “oxygen electrode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Oxygen electrode bifunctional electrocatalyst NiCo2O4 spinel

A significant increase in energy density may be possible if a two-unit alkaline regenerative H2-O2 fuel cell is replaced with a single-unit system that uses passive means for H2O transfer and thermal control. For this single-unit system, new electrocatalysts for the O2 electrode will be required which are not only bifunctionally active but also chemically and electrochemically stable between the voltage range of about 0.7 and 1.5 V. NiCo2O4 spinel is reported to have certain characteristics that make it useful for a study of electrode fabrication techniques. High surface area NiCo2O4 powder was fabricated into unsupported, bifunctional, PTFE-bonded, porous gas fuel cell electrodes by commercial sources using varying PTFE contents and sintering temperatures. The object of this study is to measure the bifunctional activities of these electrodes and to observe what performance differences might result from different commercial electrode fabricators. O2 evolution and O2 reduction data were obtained at 80 C (31 percent KOH). An irreversible reaction (i.e., aging) occurred during O2 evolution at potentials greater than about 1.5 V. Anodic Tafel slopes of 0.06 and 0.12 V/decade were obtained for the aged electrodes. Within the range of 15 to 25 percent, the PTFE content was not a critical parameter for optimizing the electrode for O2 evolution activity. Sintering temperatures between 300 and 340 C may be adequate but heating at 275 C may not be sufficient to properly sinter the PTFE-NiCo2O4 mixture. Electrode disintegration was observed during O2 reduction. Transport of O2 to the NiCo2O4 surface became prohibitive at greater than about -0.02 A/sq cm. Cathodic Tafel slopes of -0.6 and -0.12 V/decade were assumed for the O2 reduction process. A PTFE content of 25 percent (or greater) appears to be preferable for sintering the PTFE-NiCo2O4 mixture.

Fielder, William L.↗
NASA NTRS1989

Electrocatalysts for oxygen electrodes in fuel cells and water electrolyzers for space applications

In most instances separate electrocatalysts are needed to promote the reduction of O2 in the fuel cell mode and to generate O2 in the energy storage-water electrolysis mode in aqueous electrochemical systems operating at low and moderate temperatures (T greater than or equal to 200 C). Interesting exceptions are the lead and bismuth ruthenate pyrochlores in alkaline electrolytes. These catalysts on high area carbon supports have high catalytic activity for both O2 reduction and generation (1,2). Rotating ring-disk electrode measurements provide evidence that the O2 reduction proceeds by a parallel four-electron pathway. The ruthenates can also be used as self-supported catalysts to avoid the problems associated with carbon oxidation, but the electrode performance so far achieved in the research at Case Western Reserve University (CWRU) is considerably less. At the potentials involved in the anodic mode the ruthenate pyrochlores have substantial equilibrium solubility in concentrated alkaline electrolyte. This results in the loss of catalyst into the bulk solution and a decline in catalytic activity. Furthermore, the hydrogen generation counter electrode may become contaminated with reduction products from the pyrochlores (lead, ruthenium). A possible approach to this problem is to immobilize the pyrochlore catalyst within an ionic-conducting solid polymer, which would replace the fluid electrolyte within the porous gas diffusion O2 electrode. For bulk alkaline electrolyte, an anion-exchange polymer is needed with a transference number close to unity for the Oh(-) ion. Preliminary short-term measurements with lead ruthenates using a commercially available partially-fluorinated anion-exchange membrane as an overlayer on the porous gas-fed electrode indicate lower anodic polarization and virtually unchanged cathodic polarization.

Prakash, Jai↗
NASA NTRS1989

Electrocatalysis for oxygen electrodes in fuel cells and water electrolyzers for space applications

In most instances separate electrocatalysts are needed to promote the reduction of O2 in the fuel cell mode and to generate O2 in the energy storage-water electrolysis mode in aqueous electrochemical systems operating at low and moderate temperatures (T greater than or equal to 200 C). Interesting exceptions are the lead and bismuth ruthenate pyrochlores in alkaline electrolytes. These catalysts on high area carbon supports have high catalytic activity for both O2 reduction and generation. Rotating ring-disk electrode measurements provide evidence that the O2 reduction proceeds by a parallel four-electron pathway. The ruthenates can also be used as self-supported catalysts to avoid the problems associated with carbon oxidation, but the electrode performance so far achieved in the research at Case Western Reserve University (CWRU) is considerably less. At the potentials involved in the anodic mode the ruthenate pyrochlores have substantial equilibrium solubility in concentrated alkaline electrolyte. This results in the loss of catalyst into the bulk solution and a decline in catalytic activity. Furthermore, the hydrogen generation counter electrode may become contaminated with reduction products from the pyrochlores (lead, ruthenium).

Prakash, Jai↗
NASA NTRS1989

Oxygen electrodes for rechargeable alkaline fuel cells-II

The primary objective of this program is the investigation and development of electrocatalysts and supports for the positive electrode of moderate temperature single-unit rechargeable alkaline fuel cells. Approximately six support materials and five catalyst materials have been identified to date for further development.

Swette, L.↗
NASA NTRS1990

Electrocatalysis for oxygen electrodes in fuel cells and water electrolyzers for space applications

The lead ruthenate pyrochlore Pb2Ru2O6.5, in both high- and low-area forms, has been characterized using thermogravimetric analysis, X-ray photoelectron spectroscopy, X-ray diffraction, cyclic voltammetry, and O2 reduction and generation kinetic-mechanistic studies. Mechanisms are proposed. Compounds in which part of the Ru is substituted with Ir have also been prepared. They exhibit somewhat better performance for O2 reduction in porous, gas-fed electrodes than the unsubstituted compound. The anodic corrosion resistance of pyrochlore-based porous electrodes was improved by using two different anionically conducting polymer overlayers, which slow down the diffusion of ruthenate and plumbate out of the electrode. The O2 generation performance was improved with both types of electrodes. With a hydrogel overlayer, the O2 reduction performance was also improved.

Prakash, Jai↗
NASA NTRS1990

Oxygen electrodes for rechargeable alkaline fuel cells. II

The primary objective of this program is the investigation and development of electrocatalysts and supports for the positive electrode of moderate temperature, single-unit, rechargeable alkaline fuel cells. Approximately six support materials and five catalyst materials have been identified to date for further development.

Swette, L.↗
NASA NTRS1991

Oxygen electrodes for rechargeable alkaline fuel cells, 3

The investigation and development of electrocatalysts and supports for the positive electrode of moderate-temperature single unit rechargeable alkaline fuel cells is described with focus on chemical and electrochemical stability and O2 reduction/evolution activity.

L Swette↗
NASA NTRS2005

Bifunctional catalytic electrode

The present invention relates to an oxygen electrode for a unitized regenerative hydrogen-oxygen fuel cell and the unitized regenerative fuel cell having the oxygen electrode. The oxygen electrode contains components electrocatalytically active for the evolution of oxygen from water and the reduction of oxygen to water, and has a structure that supports the flow of both water and gases between the catalytically active surface and a flow field or electrode chamber for bulk flow of the fluids. The electrode has an electrocatalyst layer and a diffusion backing layer interspersed with hydrophilic and hydrophobic regions. The diffusion backing layer consists of a metal core having gas diffusion structures bonded to the metal core.

Cisar, Alan↗
DOE OSTI2024

A Multifunctional Isostructural Bilayer Oxygen Evolution Electrode for Durable Intermediate-Temperature Electrochemical Water Splitting

The overarching goal of the proposed research is to address SOEC’s degradation problem by advancing a new isostructural highly electrocatalytically active bilayer oxygen evolution reaction (OER) electrode, consisting of a LSCF (La 1-x Sr x Co 1-y Fe y O 3-δ ) core and a SCT (SrCo 0.9 Ta 0.1 O 3-δ ) shell, to achieve high and sustainable rate of oxygen evolution matching operating current densities without encountering delamination. To realize this goal, the project has adopted a combined experimental and theoretical approach to conduct research in the following six areas closely associated with SOPO tasks: 1) Development of electrocatalytically active bilayer oxygen electrodes (SOPO task-1) 2) Development of new symmetric three electrode cell (STEC) methodology to extract electrokinetic data of oxygen electrodes (SOPO task-2) 3) Quantification of electrokinetics of bilayer oxygen electrodes and correlation with degradation and delamination (SOPO task-2) 4) Performances of bilayer oxygen electrodes under fuel cells and electrolyzers modes (SOPO task-3) 5) Microscale modeling of oxygen electrode/electrolyte interface in solid oxide electrolysis cells (SOPO task-4) 6) Prediction of crack growth rate at oxygen electrode/electrolyte interface in solid oxide electrolysis cells (SOPO task-4)

08 HYDROGEN↗
DOE OSTI2024

Development of Stable Solid Oxide Electrolysis Cells for Low-Cost Hydrogen Production

The project objective was to demonstrate a solid oxide cell-based steam electrolysis stack that exhibits robustness, reliability, endurance, hydrogen purity, and produces hydrogen at elevated pressure of 2 to 3 bar. Innovative materials and processing methods were evaluated to improve degradation characteristics. Performance improvement focused on nearly all layers involved in the cell and stack assembly. Primary attention was paid to zirconia-ceria interface resistance control via sintering optimization and decrease in degradation from the oxygen electrode by evaluating low strontium (Sr) or Sr-free composition for both the oxygen electrode and current collection layer. Stack robustness was addressed by validating redox tolerance of fuel electrode, confirming capability of cells to survive repeated thermal cycles, studying the effect of pressure on performance and degradation, evaluating the effect of contamination on fuel and oxygen electrode performance and degradation, and identifying mitigation strategies to improve performance. The characterization included evaluation of electrochemical performance and stability followed by microstructural analysis. At the cell level, performance and stability improvements were achieved by incorporating a Sr-free oxygen electrode and a denser oxygen electrode barrier layer. At the stack level, pressurized operation reduces demand on first stage compression, the redox tolerant fuel electrode mitigates risk from service interruptions, and improvements to interconnect coating alleviate chromium (Cr) contamination effects. The denser barrier layer was achieved by adding a sintering aid to the samaria-doped ceria (SDC) composition that reduced sintering temperature by 150 °C. The resulting density was on par with the baseline SDC barrier layer density and the lower sintering temperature resulted in less resistive phase formation during sintering. Button cell tests did not demonstrate a change in performance when exposed to silicon (Si) or manganese (Mn) impurities to the fuel electrode and Cr impurity to the oxygen electrode. More detailed study however is warranted. The project addressed SOEC performance and stability at the cell and stack levels through a systematic approach to known sources of degradation that were combined and tested in three stack tests using an electrolyte supported cell design to allow for evaluation of a variety of fuel and oxygen electrode compositions. STK-82 and STK-83 had identical compositions. STK-100 incorporated the best materials and processing variables developed under this and concurrent projects, and was tested at elevated pressure in steam electrolysis. • STK-82 recovered performance after redox and thermal cycling, demonstrating the robustness of the stack and seals. It exhibited stable performance in testing for 500 hours in SOEC mode, followed by 300 hours of cycling between SOEC and SOFC tests. Degradation during SOEC operation was 1.8 %/ 1,000 hours. • STK-83 generated hydrogen at >80% steam conversion, and oxygen above 98.5 % purity during pressurized operation. Both hydrogen and oxygen were generated at 3 barg pressure without the use of a pressure vessel. In addition to balanced pressure, electrolysis operation at 1 bar differential pressure across anode and cathode was also demonstrated to substantial the robustness of the cell and seal. • STK-100 measured at initial ambient pressure conditions showed an area specific resistance of 1.1 ohm-cm 2 , and STK-83 had 1.3 ohm-cm 2 .

08 HYDROGEN↗
DOE OSTI2023

Cobalt-substituted perovskite compounds for solid oxide electrochemical cells

Oxygen electrodes are provided, comprising a perovskite compound having Formula (I), Sr(Ti 1-x Fe x-y Co y )O 3-δ wherein 0.90 ≥ x ≥ 0.40 and 0.02 ≥ y ≥ 0.30. Electrochemical devices comprising such oxygen electrodes are also provided, comprising a counter electrode in electrical communication with the oxygen electrode, and a solid oxide electrolyte between the oxygen electrode and the counter electrode. Methods of using such electrochemical devices are also provided, comprising exposing the oxygen electrode to a fluid comprising O 2 under conditions to induce the reaction O 2 +4e − →2O 2− , or to a fluid comprising O 2− under conditions to induce the reaction 2O 2− →O 2 +4e − .

Zhang, Shan-Lin↗
DOE OSTI2024

Modeling Oxygen Partial Pressure in Solid Oxide Electrolysis Cells: The Microstructure Effect

Oxygen partial pressure is an important thermodynamic state variable that affects both the performance and degradation of solid oxide electrolysis cells. In this work, a 3D model developed from Virkar’s 1D model has been applied to reconstructed and synthetic microstructures of Ni-YSZ-GDC-LSCF cell. The effect of the microstructures, including the thickness of the YSZ and GDC layer, and the compositions of the hydrogen and oxygen electrode, on the distribution of oxygen partial pressure has been investigated. The results show that the maximum oxygen partial pressure may occur on the interface between oxygen electrode and GDC layer or between GDC layer and YSZ layer depending on the rate of oxygen ion exchange between GDC and YSZ. A thicker GDC layer lowers the maximum oxygen partial pressure in the cell, while a thicker YSZ layer lowers the maximum oxygen partial pressure in the hydrogen electrode. In addition, the Ni:YSZ ratio and porosity also affects the maximum partial pressure. These findings provide insights on mitigating degradation in solid oxide electrolysis cell by tuning the microstructures.

Lei, Yinkai↗
DOE OSTI2025

Investigation of MO x (M = Cr, Mn, Re, and Mo) coated stainless-steel electrodes for oxygen evolution reaction in natural seawater electrolysis

Seawater electrolysis is considered a potential strategy for large-scale of affordable H 2 production. However, poor durability of the anode for oxygen evolution reaction (OER) in natural seawater is a remaining concern due to chloride-induced reaction. Herein, the effect of various MO x (M = Mn, Cr, Re, and Mo) coated stainless steel (SS) electrodes on OER in direct natural seawater electrolysis was comprehensively studied. It is found that the Mo-coated SS electrode is superior to all others in terms of durability, followed by Re-coated SS, while the Cr and Mn-coated SS electrodes show the poorest durability. Additionally, the durability and activity of the Mo/SS electrode can be boosted remarkably in 1 M KOH/seawater compared to the natural seawater, resulting in an overpotential at 10 mA cm −2 decrease from 830 to 399 mV. Meanwhile, no degradation is observed at 1000 mA cm −2 for 100 h in 1 M KOH seawater, which is among the best stability, based on the literature review. Moreover, the improved durability and activity with Mo coating were extended to the Inconel 718 substrate, and around 40 % improvement in durability and 25 mV overpotential decrease at 10 mA cm −2 are observed, which indicates that Mo coating can be considered as a universal approach to improve the anode durability and activity. The improved performance with Mo coating may be attributed to the continuous Mo oxide layer formation or in situ generated MoO 4 2− in the OER process. In conclusion, this work provides a holistic strategy to enhance the anode durability and activity under harsh conditions, offering valuable insights for designing corrosion-resistant electrodes in direct seawater electrolysis.

Direct seawater electrolysis↗
NASA NTRS1990

Integrated regenerative fuel cell experimental evaluation

An experimental test program was conducted to investigate the performance characteristics of an integrated regenerative fuel cell (IRFC) concept. The IRFC consists of a separate fuel cell unit and electrolysis cell unit in the same structure, with internal storage of fuel cell product water and external storage of electrolysis cell produced hydrogen and oxygen. The fuel cell unit incorporates an enhanced Orbiter-type cell capable of improved performance at reduced weight. The electrolysis cell features a NiCo2O4 catalyst oxygen evolution eletrode with a porous Teflon cover to retard electrolyte loss. Six complete IRFC assemblies were assembled and performance tested at an operating temperature of 200 F (93.3 C) and reactant pressures up to 170 psia (117.2 n/cu cm) on IRFC No. 4. Anomalous pressure charge/discharge characteristics were encountered during performance evaluation. A reversible fuel cell incorporating a proprietary bi-functional oxygen electrode operated satisfactory at 200 F (93.3 C) at reactant pressures up to 50 psia (41.4 n/cu cm) as a regenerative fuel cell for one cycle, before developing an electrical short in the fuel cell mode. Electrolysis cell 300-hour endurance tests demonstrated the electrolyte retention capability of the electrode Teflon cover and the performance stability of the bi-functional oxygen electrode at high potential.

Martin, Ronald E.↗
DOE OSTI2025

Enhancing surface activity and durability in triple conducting electrode for protonic ceramic electrochemical cells

With the material system operating at lower temperatures, protonic ceramic electrochemical cells (PCECs) can offer high energy efficiency and reliable performance for both power generation and hydrogen production, making them a promising technology for reversible energy cycling. However, PCEC faces technical challenges, particularly regarding electrode activity and durability under high current density operations. To address these challenges, we introduce a nano-architecture oxygen electrode characterized by high porosity and triple conductivity, designed to enhance catalytic activity and interfacial stability through a self-assembly approach, while maintaining scalability. Electrochemical cells incorporating this advanced electrode demonstrate robust performance, achieving a peak power density of 1.50 W cm −2 at 600 °C in fuel cell mode and a current density of 5.04 A cm −2 at 1.60 V in electrolysis mode, with enhanced stability on transient operations and thermal cycles. The underlying mechanisms are closely related to the improved surface activity and mass transfer due to the dual features of the electrode structure. Additionally, the enhanced interfacial bonding between the oxygen electrode and electrolyte contributes to increased durability and thermomechanical integrity. This study underscores the critical importance of optimizing electrode microstructure to achieve a balance between surface activity and durability.

Protonic Ceramic Electrochemical Cells↗
NASA NTRS1977

Recent advances in the understanding of electrocatalysis and its relation to surface chemistry

It is pointed out that electrosorption plays a key role in electrocatalysis. Little information is available, however, concerning the chemical nature of the interactions of the adsorbed species with the electrode and even less about the adsorption sites. The role of adsorbed species and surface layers in electrocatalysis is reviewed for several electrode systems. In recent years, some general insights have been achieved into the relationship of hydrogen electrode kinetics to hydrogen adsorption. For a given mechanism the exchange current density is related to the standard free energy of adsorption of the particular type of adsorbed hydrogen upon which the kinetics depend. The oxygen electrode reactions are less well understood than the reactions for the hydrogen electrode. The pronounced irreversibility of the oxygen electrode reactions at moderate temperatures has severely complicated mechanistic studies.

Yeager, E.↗