Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “optimum design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

The use of subjective expert opinions in cost optimum design of aerospace structures

The results of two questionnaires sent to engineering experts are statistically analyzed and compared with objective data from Saturn V design and testing. Engineers were asked how likely it was for structural failure to occur at load increments above and below analysts' stress limit predictions. They were requested to estimate the relative probabilities of different failure causes, and of failure at each load increment given a specific cause. Three mathematical models are constructed based on the experts' assessment of causes. The experts' overall assessment of prediction strength fits the Saturn V data better than the models do, but a model test option (T-3) based on the overall assessment gives more design change likelihood to overstrength structures than does an older standard test option. T-3 compares unfavorably with the standard option in a cost optimum structural design problem. The report reflects a need for subjective data when objective data are unavailable.

Thomas, J. M.↗
NASA NTRS1966

Calculations enable optimum design of magnetic brake

Mathematical analysis and computations determine optimum magnetic coil configurations for a magnetic brake which controllably decelerates a free falling load to a soft stop. Calculations on unconventionally wound coils determine the required parameters for the desired deceleration with minimum electrical energy supplied to the stationary coil.

Kosmahl, H. G.↗
NASA NTRS1971

On the selection of an optimum design point for phase-coherent receivers employing band-pass limiters.

Discussion of the optimum power allocation problem associated with the design of a phase-coherent receiver employing a bandpass limiter. A single channel system is treated in detail, and an optimization technique is proposed that makes use of up-to-date phase-locked loop and bandpass limiter theories recently contributed by Lindsey (1969) and Springett and Simon (1971). It is shown how this technique can be extended to a two-channel system.

Simon, M. K.↗
NASA NTRS1979

Optimum design of spacecraft radiators for large capacity or long duration mission applications

Results of trade studies comparing optimum pumped fluid and hybrid heat pipe/pumped fluid radiator designs are presented. Design variables considered in the system optimization analyses include transport fluid properties and Reynolds number, pump loop component reliabilities, micrometeoroid protection, heat pipe spacing, manifolding and flow routing in pumped fluid designs, transport tubing spacing and diameters, and radiator fin parameters. Criteria for evaluating candidate radiator system designs include mass, radiator area, and overall system reliability. The studies show advantages in constructing large systems from small independent subsystems with oversizing to account for subsystem failures. The optimum size and survivability of the subsystems are identified as a function of the radiator construction, the system heat rejection requirements, the mission duration, and the system reliability requirements.

Leach, J. W.↗
NASA NTRS1978

Dynamic programming and direct interaction for the optimum design of skeletal towers

A computer technique is proposed for automatically designing tower structures. Dynamic programming was used to find the optimum geometric configuration of the structural members, while the member sizes were proportioned by direct iteration. Tower structures are particularly suited to this method of automatic design since the rapidity of the analysis and design depends primarily upon substructuring. Substructuring of towers was comparatively simple because interaction between adjacent substructures is simulated with reasonable accuracy. Typical examples are presented to illustrate the method.

Howell, G. C.↗
NASA NTRS1992

Optimum design using VICONOPT, a buckling and strength constraint program for prismatic assemblies of anisotropic plates

A computer program for obtaining the optimum (least mass) dimensions of the kind of prismatic assemblies of laminated, composite plates which occur in advanced aerospace construction is described. Rigorous buckling analysis (derived from exact member theory) and a tailored design procedure are used to produce designs which satisfy buckling and material strength constraints and configurational requirements. Analysis is two to three orders of magnitude quicker than FEM, keeps track of all the governing modes of failure and is efficiently adapted to give sensitivities and to maintain feasibility. Tailoring encourages convergence in fewer sizing cycles than competing programs and permits start designs which are a long way from feasible and/or optimum. Comparisons with its predecessor, PASCO, show that the program is more likely to produce an optimum, will do so more quickly in some cases, and remains accurate for a wider range of problems.

Butler, R.↗
NASA NTRS1992

Optimum design of a gearbox for low vibration

A computer program was developed for designing a low vibration gearbox. The code is based on a finite element shell analysis, a modal analysis, and a structural optimization method. In the finite element analysis, a triangular shell element with 18 degrees-of-freedom is used. In the optimization method, the overall vibration energy of the gearbox is used as the objective function and is minimized at the exciting frequency by varying the finite element thickness. Modal analysis is used to derive the sensitivity of the vibration energy with respect to the design variable. The sensitivity is representative of both eigenvalues and eigenvectors. The optimum value is computed by the gradient projection method and a unidimensional search procedure under the constraint condition of constant weight. The computer code is applied to a design problem derived from an experimental gearbox in use at the NASA Lewis Research Center. The top plate and two side plates of the gearbox are redesigned and the contribution of each surface to the total vibration is determined. Results show that optimization of the top plate alone is effective in reducing total gearbox vibration.

Inoue, Katsumi↗
NASA NTRS1973

Quasi-optimum design of a six degree of freedom moving base simulator control system

The design of a washout control system for a moving base simulator is treated by a quasi-optimum control technique. The broad objective of the design is to reproduce the sensed motion of a six degree of freedom simulator as accurately as possible without causing the simulator excursions to exceed specified limits. A performance criterion is established that weights magnitude and direction errors in specific force and in angular velocity and attempts to maintain the excursion within set limits by penalizing excessive excursions. A FORTRAN routine for relizing the washout law was developed and typical time histories using the washout routine were simulated for a range of parameters in the penalty- and weighting-functions. These time histories and the listing of the routine are included in the report.

Friedland, B.↗
NASA NTRS1988

Optimum design of geodesically stiffened composite plates

With the goal of tailorability in mind, the in-plane stiffness characteristics of a particular grid stiffened plate configuration under axial and shear loads have been studied. The contribution of the skin to the stiffener network and the resultant skin/rib interaction is analyzed. For the given plate geometry and loads, it is shown that an optimum configuration does exist. To achieve optimally designed practical plate configurations, buckling constraints need to be included in the design. Due to the complex geometry and loading of the plates, a simplified local buckling analysis of isolated stiffeners and triangular skin elements between the stiffeners is considered. Development of a stiffener buckling analysis represent stiffeners as shear deformable plate elements is presented.

Guerdal, Zafer↗
NASA NTRS1977

Optimum design and performance of Costas receivers containing soft bandpass limiters

This paper investigates several key questions concerning the mechanization and design of a Costas receiver for reconstruction of a carrier from a suppressed carrier signal. For baseband NRZ encoded data symbols and a soft bandpass limiter preceding the loop, several design issues which are considered herein and which affect acquisition and tracking performance are: (1) The choice of an IF bandwidth. (2) The optimum choice of the Costas arm filter bandwidths as well as the spectral roll-off characteristics. (3) The optimum choice of loop bandwidth to data rate ratio for a given signal-to-noise ratio. (4) The signal suppression factor and the combined limiter-squaring loss. (5) The variations in loop bandwidth and damping with signal level. (6) The choice of the limiter transfer characteristic. (7) Performance degradation due to the presence of a limiter. Various new results in system design are presented and typical numerical results are given and graphically demonstrated in SNR regions of practical interest. The theory is applicable to the design of carrier reconstruction loops required in the implementation of spread spectrum communication receivers.

Lindsey, W. C.↗
NASA NTRS1995

An integrated optimum design approach for high speed prop rotors

The objective is to develop an optimization procedure for high-speed and civil tilt-rotors by coupling all of the necessary disciplines within a closed-loop optimization procedure. Both simplified and comprehensive analysis codes are used for the aerodynamic analyses. The structural properties are calculated using in-house developed algorithms for both isotropic and composite box beam sections. There are four major objectives of this study. (1) Aerodynamic optimization: The effects of blade aerodynamic characteristics on cruise and hover performance of prop-rotor aircraft are investigated using the classical blade element momentum approach with corrections for the high lift capability of rotors/propellers. (2) Coupled aerodynamic/structures optimization: A multilevel hybrid optimization technique is developed for the design of prop-rotor aircraft. The design problem is decomposed into a level for improved aerodynamics with continuous design variables and a level with discrete variables to investigate composite tailoring. The aerodynamic analysis is based on that developed in objective 1 and the structural analysis is performed using an in-house code which models a composite box beam. The results are compared to both a reference rotor and the optimum rotor found in the purely aerodynamic formulation. (3) Multipoint optimization: The multilevel optimization procedure of objective 2 is extended to a multipoint design problem. Hover, cruise, and take-off are the three flight conditions simultaneously maximized. (4) Coupled rotor/wing optimization: Using the comprehensive rotary wing code CAMRAD, an optimization procedure is developed for the coupled rotor/wing performance in high speed tilt-rotor aircraft. The developed procedure contains design variables which define the rotor and wing planforms.

Chattopadhyay, Aditi↗
NASA NTRS2014

Wing Configuration Impact on Design Optimums for a Subsonic Passenger Transport

This study sought to compare four aircraft wing configurations at a conceptual level using a multi-disciplinary optimization (MDO) process. The MDO framework used was created by Georgia Institute of Technology and Virginia Polytechnic Institute and State University. They created a multi-disciplinary design and optimization environment that could capture the unique features of the truss-braced wing (TBW) configuration. The four wing configurations selected for the study were a low wing cantilever installation, a high wing cantilever, a strut-braced wing, and a single jury TBW. The mission that was used for this study was a 160 passenger transport aircraft with a design range of 2,875 nautical miles at the design payload, flown at a cruise Mach number of 0.78. This paper includes discussion and optimization results for multiple design objectives. Five design objectives were chosen to illustrate the impact of selected objective on the optimization result: minimum takeoff gross weight (TOGW), minimum operating empty weight, minimum block fuel weight, maximum start of cruise lift-to-drag ratio, and minimum start of cruise drag coefficient. The results show that the design objective selected will impact the characteristics of the optimized aircraft. Although minimum life cycle cost was not one of the objectives, TOGW is often used as a proxy for life cycle cost. The low wing cantilever had the lowest TOGW followed by the strut-braced wing.

Wells, Douglas P.↗