Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “mode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

An investigation of accelerating mode and decelerating mode constant-momentum mass spectrometry and their application to a residual gas analyzer

A theoretical analysis of constant momentum mass spectrometry was made. A maximum resolving power for the decelerating mode constant momentum mass spectrometer was shown theoretically to exist for a beam of ions of known energy. A vacuum system and an electron beam ionization source was constructed. Supporting electronics for a residual gas analyzer were built. Experimental investigations of various types of accelerating and decelerating impulsive modes of a constant momentum mass spectrometer as applied to a residual gas analyzer were made. The data indicate that the resolving power for the decelerating mode is comparable to that of the accelerating mode.

Ng, Y. S.↗
NASA NTRS1987

Multiperiodic irradiance changes caused by r-modes and g-modes

More than 20 real periodicities ranging from 20 days to 2 years modulate the solar irradiance data accumulated since November 1978 by Nimbus 7. Many are quite strong during the first three years (solar maximum) and weak after that. There is a high correspondence between periods in irradiance and 28 periods predicted from the rotation and beating of global solar oscillations (r-modes and g-modes). Angular states l = 1, 2, and 3 are detected as well as some unresolved r-mode power at higher l. The prominence of beat periods implies a nonlinear system whose effective nonlinear power was measured to be about 2. This analysis constitutes a detection of r-modes in the sun, and determines from them a mean sidereal rotation rate for the convective envelope of 459 + or - 4 nHz which converts to a period of 25.2 days (27.1d, synodic).

Wolff, Charles L.↗
NASA NTRS1991

Combined mode I-mode III fracture toughness of a particulate reinforced metal-matrix composite

The aim of this investigation was to determine the fracture behavior of a particulate reinfored aluminum alloy composite under combined mode I-mode III loading conditions. A modified three-point bend specimen was used to carry out these tests. It was found that the mode I loading condition was energetically most favorable. Addition of mode III components to the system seems to increase the amount of redundant work during fracture without affecting the critical fracture criterion.

Manoharan, M.↗
NASA NTRS2010

Mode Tracker for Mode-Hop-Free Operation of a Laser

A mode-tracking system that includes a mode-controlling subsystem has been incorporated into an external-cavity (EC) quantum cascade laser that operates in a mid-infrared wavelength range. The mode-tracking system makes it possible to perform mode-hop-free wavelength scans, as needed for high-resolution spectroscopy and detection of trace gases. The laser includes a gain chip, a beam-collimating lens, and a diffraction grating. The grating is mounted on a platform, the position of which can be varied to effect independent control of the EC length and the grating angle. The position actuators include a piezoelectric stage for translation control and a motorized stage for coarse rotation control equipped with a piezoelectric actuator for fine rotation control. Together, these actuators enable control of the EC length over a range of about 90 m with a resolution of 0.9 nm, and control of the grating angle over a coarse-tuning range of +/-6.3deg and a fine-tuning range of +/-520 microrad with a resolution of 10 nrad. A mirror mounted on the platform with the grating assures always the same direction of the output laser beam.

Wysocki, Gerard↗
NASA NTRSDate not supplied

Mode Projection Method for Target Mode Identification

A method for projecting flight configuration eigenvectors onto the vector space of the test configuration eigenvectors is proposed. The underlying concept of the proposed method is that any flight configuration eigenvectors (that can be replicated by a linear combination of test configuration eigenvectors) is correlated if the constituent test eigenvectors are themselves correlated. Therefore, the modal test target mode shapes should be those test modes that combine to form the important modes of the flight configurations. This approach also recognizes that it is the deformed shapes that dictate what sections of the structure are “highly strained” (in a relative sense, within each mode shape), and that these “highly strained” sections require an accurate stiffness representation to achieve an accurate model correlation.

Jeffrey A Peck↗
NASA NTRS2026

Cryogenic Mixed Mode I – Mode II Fracture Toughness of Various Polymer Composite Materials

The present study investigates the mixed mode interlaminar fracture toughness of six polymer matrix composite materials at both room temperature and cryogenic liquid nitrogen temperature. The single leg bending test employed gives a mix of Mode I (opening) and Mode II (in-plane shearing) cracking. The tested thermoplastic-matrix composites were shown to have total mixed mode toughnesses 3.1–4.3 times higher than those of representative thermoset resin composites.

Carbon fiber↗
DOE OSTI2026

Turbulence-Driven Edge-Localized-Mode-Free High-Confinement Mode with Divertor Detachment in a Metal-Wall Tokamak

We report the first demonstration of a minute-scale, edge-localized-mode-free high-confinement plasma regime compatible with divertor partial detachment and enhanced pedestal performance in a metal-wall tokamak, the Experimental Advanced Superconducting Tokamak. This regime is enabled by a newly identified mechanism: during divertor partial detachment, reduced ionization and enhanced pumping in a closed divertor lead to less cooling of the pedestal by recycling neutrals and seeding impurities, resulting in an increased pedestal temperature gradient, which excites high-frequency broadband turbulence. Gyrokinetic simulations identify the high-frequency broadband turbulence as a temperature-gradient-driven trapped electron mode (𝜂 𝑒 -TEM), which drives outward transport of particles and heat, thereby maintaining the edge-localized-mode-free state. This pedestal regime is particularly promising for the International Thermonuclear Experimental Reactor, where the anticipated lower density gradient, reduced E×B shear, and lower collisionality in the pedestal will further facilitate 𝜂 𝑒 -TEM excitation. The achieved integrated scenario with a detached divertor and turbulence-dominated pedestal thus offers a compelling solution for managing heat loads and metal impurity sources for long-pulse high-performance operation in future fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1974

User's manual for the coupled mode version of the normal modes rotor aeroelastic analysis computer program

This User's Manual was prepared to provide the engineer with the information required to run the coupled mode version of the Normal Modes Rotor Aeroelastic Analysis Computer Program. The manual provides a full set of instructions for running the program, including calculation of blade modes, calculations of variable induced velocity distribution and the calculation of the time history of the response for either a single blade or a complete rotor with an airframe (the latter with constant inflow).

Bergquist, R. R.↗
NASA NTRS1978

Optimum wall impedance for spinning modes - A correlation with mode cut-off ratio

A correlating equation relating the optimum acoustic impedance for the wall lining of a circular duct to the acoustic mode cut-off ratio is presented and compared to exact calculations. The optimum impedance was correlated with cut-off ratio because the cut-off ratio appears to be the fundamental parameter governing the propagation of sound in the duct. Modes with similar cut-off ratios respond in a similar way to the acoustic liner. The correlating equation is useful for the design of suppressors for aircraft engine inlets having a steady mean flow with a boundary layer and spinning mode noise source excitation. The correlation is a semi-empirical expression developed from an empirical modification of an equation originally derived from sound propagation theory in a thin boundary layer. Exact calculations of the optimum wall impedance were made over a wide range of frequency parameters, boundary layer thicknesses and flow Mach numbers to develop and verify the correlation. This correlating equation represents a part of a simplified liner design method, based upon modal cut-off ratio, for multimodal noise propagation.

Rice, E. J.↗
NASA NTRS1978

Elastic-Plastic Finite Element Analysis of Fatigue Crack Growth in Mode 1 and Mode 2 Conditions

Presented is an alternate cost-efficient and accurate elastic-plastic finite element procedure to analyze fatigue crack closure and its effects under general spectrum loading. Both Modes 1 and 2 type cycling loadings are considered. Also presented are the results of an investigation, using the newly developed procedure, of various factors that cause crack growth acceleration or retardation and delay effects under high-to-low, low-to-high, single overload, and constant amplitude type cyclic loading in a Mode 1 situation. Further, the results of an investigation of a centercracked panel under external pure shear (Mode 2) cyclic loading, of constant amplitude, are reported.

Nakagaki, M.↗
NASA NTRS1988

Characterization of Mode 1 and Mode 2 delamination growth and thresholds in graphite/peek composites

Composite materials often fail by delamination. The onset and growth of delamination in AS4/PEEK, a tough thermoplastic matrix composite, was characterized for mode 1 and mode 2 loadings, using the Double Cantilever Beam (DCB) and the End Notched Flexure (ENF) test specimens. Delamination growth per fatigue cycle, da/dN, was related to strain energy release rate, G, by means of a power law. However, the exponents of these power laws were too large for them to be adequately used as a life prediction tool. A small error in the estimated applied loads could lead to large errors in the delamination growth rates. Hence strain energy release rate thresholds, G sub th, below which no delamination would occur were also measured. Mode 1 and 2 threshold G values for no delamination growth were found by monitoring the number of cycles to delamination onset in the DCB and ENF specimens. The maximum applied G for which no delamination growth had occurred until at least 1,000,000 cycles was considered the threshold strain energy release rate. Comments are given on how testing effects, facial interference or delamination front damage, may invalidate the experimental determination of the constants in the expression.

Martin, Roderick H.↗
NASA NTRS1990

Characterization of Mode I and Mode II delamination growth and thresholds in AS4/PEEK composites

Composite materials often fail by delamination. The onset and growth of delamination in AS4/PEEK, a tough thermoplastic matrix composite, was characterized for mode 1 and mode 2 loadings, using the Double Cantilever Beam (DCB) and the End Notched Flexure (ENF) test specimens. Delamination growth per fatigue cycle, da/dN, was related to strain energy release rate, G, by means of a power law. However, the exponents of these power laws were too large for them to be adequately used as a life prediction tool. A small error in the estimated applied loads could lead to large errors in the delamination growth rates. Hence strain energy release rate thresholds, G sub th, below which no delamination would occur were also measured. Mode 1 and 2 threshold G values for no delamination growth were found by monitoring the number of cycles to delamination onset in the DCB and ENF specimens. The maximum applied G for which no delamination growth had occurred until at least 1,000,000 cycles was considered the threshold strain energy release rate. Comments are given on how testing effects, facial interference or delamination front damage, may invalidate the experimental determination of the constants in the expression.

Martin, Roderick H.↗
NASA NTRS1991

Selective mode injection and observation for few-mode fiber optics

By etching the cladding along several millimeters of circular- or elliptical-core few-mode fiberoptics, access to the core is achieved and extremely pure modes can be injected. The same etching technique allows measurement of the modal purity at the far end of the fiber. Modal purities of -26 dB have been obtained. A holographic technique is also demonstrated that allows all the light of each mode to be focused to an independent spot.

Shaklan, Stuart↗
DOE OSTI2025

Voltage cycling as a dynamic operation mode for high temperature electrolysis solid oxide cells

Solid Oxide Electrolysis Cells (SOECs) have emerged as a promising technology for the efficient production of H2 via high-temperature electrolysis. However, power input from dynamic energy sources remains a significant challenge for their long-term stability. It is important to analyze the tolerance of cells under dynamic operation conditions. This study focuses on evaluating the impact of voltage cycling on the performance and durability of electrode-supported SOECs. We explore the operational limits and degradation mechanisms of SOECs subjected to various voltage conditions and find that the cells have high tolerance for dynamic voltage. Voltage cycling between 1.3 V and 1.5 V for 9000 cycles does not damage the cell. Conversely, cycling to higher voltages (≥1.7 V) results in accelerated degradation. Advanced characterization is used to screen for various degradation modes post operation. Within the oxygen electrode, XRD and STEM EDS find compositional and phase evolution in all voltage cycled samples including increased decomposition of the air electrode resulting in cation migration. Microstructural analysis of the fuel electrode from nano-CT data shows minimal change throughout the sample set and no evidence of Ni migration, indicating the fuel electrode is stable and not impacted by cycling to higher voltages within the timeframe studied.

Zhu, Zhikuan↗
DOE OSTI2025

Design of a correlation reflectometer radiometer diagnostic and measurements of the electron density–temperature cross-phase angle in the H-mode pedestal with small edge localized modes at ASDEX Upgrade

This work presents the hardware design and first results from a newly commissioned correlation reflectometer radiometer diagnostic that measures the cross-phase angle between electron density and temperature fluctuations in ASDEX Upgrade plasmas. This diagnostic employs cross correlations between signals measured by a tunable, continuous wave, perpendicular incidence, fluctuation reflectometer, and a 24-channel radiometer sharing the same line of sight. Novel measurements in the pedestal of a helium H-mode plasma with small edge localized modes show changes in the cross-phase angle between the electron density and temperature fluctuations from ∼90° to 120°, suggesting changes in the properties of the turbulence driving transport in the plasma edge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Impact of n > 1 neoclassical tearing modes on fast ions, plasma rotation, and the onset of disruptive tearing modes in DIII-D ITER baseline scenario

We present integrated TRANSP-kick analyses quantitatively characterizing how n > 1 magnetic islands redistribute fast ions (FIs) and modify momentum balance in low-torque DIII-D H-mode scenarios operated with the ITER normalized parameter set and shape (ITER baseline scenario, or IBS). In this plasma scenario, disruptive neoclassical tearing modes (NTMs) are most commonly seeded by nonlinear 3-wave coupling when the differential rotation between the q = 1 and q = 2 surfaces ($δf_{1, 2}$) approaches zero. Analysis of a DIII-D IBS database of shots unstable to the 2/1 NTM demonstrates that the flattening rotation profile is correlated with n > 1 NTM amplitude growth, with a strong drop in $δf_{1, 2}$ occurring when the radial magnetic perturbation amplitude at the rational surface ($δB$ r s ) is estimated to be about 20 G. The interpretive TRANSP-kick simulations show that the experimentally observed reduction in core rotation is due to the fast-ion kicks. Nonlinearity in momentum losses versus NTM amplitude is found to be correlated with overlap of FI island chains, occurring when $δB$ r s is about 35 G, in rough agreement with the experimental results. This agreement suggests the primary mechanism for the conductive momentum loss in the core is due to chaotic FI orbits and FI losses developing from overlapping resonant FI island chains.

ITER baseline scenario↗
DOE OSTI2026

Real-time avoidance of the L-mode and H-mode density limit via machine-learned stability metrics

Reliable operation of burning plasma tokamaks will require robust control strategies to avoid macroscopic instability limits such as the L-mode and H-mode density limits (LDL, HDL). In this work, we explore closed-loop avoidance of these phenomena at DIII-D using machine-learned risk metrics. Feedback control is implemented via the ‘DL Supervisor’ scheme, which regulates the chosen risk metric by reducing the density target or increasing NBI heating in real-time. Using the LDL 25 risk metric, the LDL is reproducibly suppressed. We also introduce an HDL risk metric in this study, HDL 25 , which reduces the False Positive Rate by 2x compared to the Greenwald fraction. Applying this scaling to a plasma current ramp-down, we successfully avoid an HDL-driven H/L back-transition. These experiments constitute the first demonstration of real-time DL avoidance using machine-learned risk metrics. These instability metrics outline a path to safer high-density operation, more reliable ramp-down scenarios, and improved off-normal control for next-step devices such as ITER and SPARC.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗