Engineering PapersSearch

SEARCH · Engineering Papers

Results for “material failure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Application of the cubic polynomial strength criterion to the failure analysis of composite materials

A comparative failure analysis is presented based on the application of quadratic and cubic forms of the tensor polynomial lamina strength criterion to various composite structural configurations in a plane stress state. Failure loads have been predicted for off-angle laminates under simple loading conditions and for symmetric-balanced laminates subject to varying degrees of biaxial tension, including configurations subject to multimode failures. Some experimental data are also provided to support these calculations. From these results, the necessity of employing a cubic strength criterion to accurately predict the failure of composite laminae is demonstrated.

Tennyson, R. C.

Weathering processes implied from analysis of small Martian avalanche chutes

It has been proposed that the smaller features of martian spur and gully slope morphology, located along the upper walls of Valles Marineris, are avalanche chutes. A three-dimensional stability back-analysis technique was developed and applied to these small avalanche chutes, yielding average values of cohesion and angle of internal friction for the mobile layer materials on these slopes at the time of each slope failure. Generally, the analysis showed that at the time of each slope failure material strengths had been reduced to those of moderately cohesive debris down through depths of tens of meters. These results have implications and possible constraints for the nature and rate of martian weathering processes.

Sullivan, R.

Acoustic emission measurements of aerospace materials and structures

A development status evaluation is given for aerospace applications of AE location, detection, and source characterization. Attention is given to the neural-like processing of AE signals for graphite/epoxy. It is recommended that development efforts for AE make connections between the material failure process and source dynamics, and study the effects of composite material anisotropy and inhomogeneity on the propagation of AE waves. Broadband, as well as frequency- and wave-mode selective sensors, need to be developed.

Sachse, Wolfgang

EFRC-MUSE: Multi-Scale Fluid-Solid Interactions in Architected and Natural Materials

Phase interactions and fluid properties in geological and other environments are critical in applications ranging from hydrogen production and geologic storage and recovery, carbon dioxide storage and sequestration, and the sustainable use of water resources. The four goals of EFRC-MUSE: Multi-Scale Fluid-Solid Interactions in Architected and Natural Materials were based on the priority directions articulated in the Basic Research Needs documents, and the scientific needs in nanoscience. 1. Develop a fundamental understanding of confinement and surface interactions in mesoscale media with nanometer-sized pores on the phase behavior, thermodynamic and multiphase flow properties of multicomponent fluid mixtures. 2. Examine the impact of mineralogy and material heterogeneity on mechanical properties to better understand chemo-mechanical interactions in material failure. 3. Determine in-operando cross-scale structural and nanostructural material properties with fluids in confinement and flow under realistic condi

58 GEOSCIENCES

Corrosion of graphite composites in phosphoric acid fuel cells

Polymers, polymer-graphite composites and different carbon materials are being considered for many of the fuel cell stack components. Exposure to concentrated phosphoric acid in the fuel cell environment and to high anodic potential results in corrosion. Relative corrosion rates of these materials, failure modes, plausible mechanisms of corrosion and methods for improvement of these materials are investigated.

Christner, L. G.

Reaction propagation test. Evaluation of the behavior of nonmetallic materials in hydrogen

Results of tests conducted to evaluate the behavior of nonmetallic materials in hydrogen are described. The reaction propagation test simulates the conditions resulting from the interaction of an electrical wire in an overload condition in contract with a material in the test medium. The test is designed to evaluate the behavior of a material subjected to an energy input (usually heat) sufficient to cause a reaction which propagates to consume larger quantities of the material. Ten nonmetallic materials were evaluated to establish baseline data on the behavior of nonmetallic materials in hydrogen and to characterize, on an initial basis, one mode of material failure considered to be a factor pertinent to the safe use of a material in hydrogen.

Smith, I. D.

Flash and fire test: Evaluation of the behavior of nonmetallic materials in hydrogen

Tests conducted to evaluate the behavior of nonmetallic materials in hydrogen are described. The results of the flash and fire test are presented. The flash and fire test is used to evaluate the tendency of heated materials to ignite in a hydrogen atmosphere when subjected to an ignition source. The test represents a hydrogen parallel to a hazard condition known to exist in oxygen systems. Ten nonmetallic materials were evaluated to establish baseline data on the behavior of the materials and to characterize one mode of material failure considered to be a factor pertinent to the safe use of a material in hydrogen.

Source record

The nonlinear bending response of thin-walled laminated composite cylinders

The geometrically nonlinear Donnell shell theory is applied to the problem of stable bending of thin-walled circular cylinders. Responses are computed for cylinders with a radius-to-thickness ratio of 50 and length-to-radius ratios of 1 and 5. Four laminated composite cylinders and an aluminum cylinder are considered. Critical moment estimates are presented for short cylinders for which compression-type buckling behavior is important, and for very long cylinders for which the cross-section flattening, i.e., Brazier effect, is important. A finite element analysis is used to estimate the critical end rotation in addition to establishing the range of validity of the prebuckling analysis. The radial displacement response shows that the character of the boundary layer is significantly influenced by the geometric nonlinearities. Application of a first ply failure analysis using the maximum stress criterion suggests that in nearly all instances material failure occurs before buckling. Failure of the composite cylinders can be attributed to fiber breakage. Striking similarities are seen between the prebuckling displacements of the bending problem and axial compression problem for short cylinders.

Fuchs, Hannes P.

Molecular dynamics simulations of ultrafast radiation induced melting at metal–semiconductor interfaces

Metal–semiconductor contacts in silicon carbide (SiC) diodes endure damages at the interface when exposed to harsh radiation environments. Due to the rapid rise in temperature and ultrafast cooling that follows the radiation impact, the structural properties of the materials can be altered through melting, recrystallization, and amorphization. A detailed understanding of the material failure modes at the interface is lacking, specifically at the nanoscale. We use molecular simulations to investigate the ultrafast melting at tungsten (W)–SiC interfaces following radiation damage and apply deep learning techniques to track the transient evolution of the local molecular structures. We show that W near the radiation track undergoes melting and, eventually, most of it recrystallizes with a noticeable degree of undercooling, while SiC is rendered permanently amorphous. The observation of local undercooling in W films is important as it can affect the device performance even before the bulk melting temperature of the material is reached. We also show that at high temperatures, the interface undergoes a fracture-like failure. The results presented here are significant in understating the different failure modes of SiC diode materials.

Ashwin Ravichandran

Modern Material Analysis Instruments Add a New Dimension to Materials Characterization and Failure Analysis

Modern analytical tools can yield invaluable results during materials characterization and failure analysis. Scanning electron microscopes (SEMs) provide significant analytical capabilities, including angstrom-level resolution. These systems can be equipped with a silicon drift detector (SDD) for very fast yet precise analytical mapping of phases, as well as electron back-scattered diffraction (EBSD) units to map grain orientations, chambers that admit large samples, variable pressure for wet samples, and quantitative analysis software to examine phases. Advanced solid-state electronics have also improved surface and bulk analysis instruments: Secondary ion mass spectroscopy (SIMS) can quantitatively determine and map light elements such as hydrogen, lithium, and boron - with their isotopes. Its high sensitivity detects impurities at parts per billion (ppb) levels. X-ray photo-electron spectroscopy (XPS) can determine oxidation states of elements, as well as identifying polymers and measuring film thicknesses on coated composites. This technique is also known as electron spectroscopy for chemical analysis (ESCA). Scanning Auger electron spectroscopy (SAM) combines surface sensitivity, spatial lateral resolution (10 nm), and depth profiling capabilities to describe elemental compositions of near and below surface regions down to the chemical state of an atom.

Panda, Binayak

Behavior of Windblown Sand on Mars: Results from Single-Particle Experiments

Experiments are investigating the behavior of individual sand grains in the high-energy martian aeolian regime. Energy partitioning during impact of a saltating grain determines grain longevity, but it also influences the way in which the bed becomes mobilized by reptation. When single grains of sand are fired into loose beds, the bed can absorb up to 90% of the impact energy by momentum transfer to other grains; it has been discovered that the impacting grains cause circular craters even at low impact angles. Hundreds of grains can be splashed by a single high-velocity (100 m/s) impact causing more bed disturbance through reptation than previously thought. The research is supported by NASA's PG&G Program. Because the martian aeolian environment in both high energy and of long duration, the most mobile fractions of windblown sand should have eradicated themselves by attrition, unless sand supply has kept pace with destruction. It is therefore important to understand the rate of grain attrition in order to make sense of the existence of vast dune fields on Mars. Attrition, has been addressed in other studies, but precise data for a single saltating grain striking a loose bed of sand have not been acquired -- the quintessential case to be understood for dunes on Mars. To acquire these data, we are employing a compound crossbow which has the bolt-firing mechanism replaced with a pneumatically-automated sabot system. The sabot can launch individual grains of sand of any size between several millimeters and about 50 microns, at velocities up to 100m/s. This is around the maximum velocity expected for saltating grains on Mars. The sabot sled is equipped with photoelectric sensors for measuring shot velocity. Baffling of the grain's exit orifice has enabled projection of single grains without significant aerodynamic effects from the sabot. Grains are fired into loose beds of sand at about 15 degrees from the horizontal (typical saltation trajectory at impact) while being filmed on high-speed video. High-intensity pulse illumination for the grains is triggered by the solenoid-operated bow trigger. A 45 degree mirror over the impact site provides simultaneous horizontal and vertical images of the impact on each video frame. UV fluorescence is enabling grain and grain-fragment recovery. At 100 m/s, grains of all sizes shatter into many fragments when the sand is replaced with a solid target. Kinetic energy of the grains at this velocity exceeds the critical energy for catastrophic failure of minerals. Although probably exceptional as a grain speed, it suggests that conditions on Mars might elevate materials into an attrition regime not encountered on other planets; individual grains blown across rock pavements on Mars will have short lifespans. When experimental grains impact loose (dune) sand, much, if not most of the kinetic energy is converted into momentum of other grains. Using high-speed filming, the energy involved in splashing grains at the impact site can be derived from the size of the crater, the speed of the splashed grains, and the rebound speed of the impactor. The amount of energy partitioned into material failure (as opposed to momentum) is too small a fraction of the total to be calculated under these circumstances. This does not necessarily mean that little damage occurs to the grains (the full extent of the damage has yet to be determined) because only a small fraction of the impact energy is required for inducing brittle fracture. Damage is orders of magnitude less than during impact against solid surfaces.

Marshall, J. R.

Particle Characterization in Rocket Exhaust Plumes

A method to characterize particles in rocket exhaust plumes is developed. The particle velocity, size, and material composition are determined from crater characteristics resulting from impacts into aluminum and copper targets passed through the plume. The targets are mounted on a steel arm approximately 21 inches (53 cm) long which is rotated through the plume at sufficient velocity to prevent material failure resulting from thermal effects. A Scanning Electron Microscope (SEM) with secondary x-ray detectors is used to determine the particle material, and a standard optical measurement microscope is used to determine the crater diameter and depth. The crater diameter and depth are used in turn, as inputs to a ballistics computer code to estimate the velocity and size of the particle. The target has a safe residence time in the plume of approximately 50 ms before reaching an unacceptably high temperature. The = must mach a velocity of 104 ft/s (32 m/s) before entering the plume to produce the design residence time of 20 ms. The arm is actuated by a torsion spring with a 5-inch (13 cm) outer diameter, 0.625-inch (16 mm wire diameter, and 11 coils. A prototype of the entire rocket exhaust particle impact characterization system (PICS) was constructed and statically tested.

Callen, E. Eugene, Jr.

Cohesive instability in elastomers: insights from a crosslinked Van der Waals fluid model

Abstract The resistance to volumetric deformations displayed by polymer networks is largely due to secondary and tertiary interactions between neighboring polymer chains. These interactions are both entropic and enthalpic in nature but are fundamentally different from the entropic forces that resist shearing in these networks. In this paper, we introduce a new depiction of elastomers as a crosslinked Van der Waals fluid. Starting from first principles, we develop constitutive equations that are implemented in a continuum model as well as a discrete network model. Our models predict that the failure of polymer networks may be driven by an instability in the underlying polymer bulk ‘fluid’ or by the breaking of polymer chains, depending on the loading path taken. The results of this study indicate that material failure in elastomers exposed to a purely triaxial state, such as in a poker chip experiment, may be driven by an entirely different mode of instability than those deformed in pure shear, such as in a uniaxial tension experiment.

Lamont, Samuel C.

Incorporation of a progressive failure analysis method in the CSM testbed software system

Analysis of the postbuckling behavior of composite shell structures pose many difficult and challenging problems in the field of structural mechanics. Current analysis methods perform well for most cases in predicting the postbuckling response of undamaged components. To predict component behavior accurately at higher load levels, the analysis must include the effects of local material failures. The CSM testbed software system is a highly modular structural analysis system currently under development at Langley Research Center. One of the primary goals of the CSM testbed is to provide a software environment for the development of advanced structural analysis methods and modern numerical methods which will exploit advanced computer architecture such as parallel-vector processors. Development of a progressive failure analysis method consists of the design and implementation of a processor which will perform the ply-level progressive failure analysis and the development of a geometrically nonlinear analysis procedure which incorporates the progressive failure processor. Regarding the development of the progressive failure processor, two components are required: failure criteria and a degradation model. For the initial implementation, the failure criteria of Hashin will be used. For a matrix failure which typically indicates the development of transverse matrix cracks, the ply properties will be degraded. Work to date includes the design of the progressive failure analysis processor and initial plans for the controlling geometrically nonlinear analysis procedure. The implementation of the progressive failure analysis has begun. Access to the model database and the Hashin failure criteria are completed. Work is in progress on the input/output operations for the processor related data and the finite element model updating procedures. In total the progressive failure processor is approximately one-third complete.

Arenburg, Robert T.

Surface and sub-surface porosity effects on the initial free surface expansion in shocked single crystal aluminum

Defects and roughness at a material’s surface can allow for the formation of a material jet when a shockwave reaches a surface. The formation of a jet can lead to significant material damage of the shocked material, as well as the downstream material that the jet impacts. Here, we utilize planar shocks in single crystal aluminum to assess initial jetting formation for surface notches and sub-surface porosity. In the case of surface notches, we find that changing the width of the notch can cause the shock breakout response to transition from a standard jetting mechanism to an atomic atomization at high velocities. This transition occurs due to the mechanisms associated with lateral relaxations within the notch and how this interacts with the shock focusing event that induces jetting. For sub-surface pores, the pore collapse induces a re-shock, localized near the pore, that is stronger than the initial shock, but unsupported. Changing the pore dimensions and location relative to the surface influences the strength of the shock that emanates from its collapse when it reaches the surface, leading to a variety of different breakout conditions including jetting and localized material failure.

36 MATERIALS SCIENCE

Thermochemical Instabilities at High Temperature Ceramic Surfaces

The surface of silicon-based high temperature ceramics exhibits thermochemical instabilities when exposed to oxygen-rich high enthalpy flows. These instabilities manifest as sudden temperature jumps of several hundred degrees and rapid material failure, when temperatures exceed 2000 K. Understanding and predicting these phenomena is critical to the design of thermal protection systems for sustained high speed flight vehicles. In this talk we review a series of test cases where surface temperature jumps were observed during plasmatron wind tunnel testing of ceramic materials, including ZrB2-SiC ultra-high temperature ceramics, C/SiC ceramic matrix composites, and silicone-based coatings for low-density carbon phenolic ablators. The underlying physical processes occurring when Si-containing ceramics are exposed to high enthalpy air flow include formation of passivating scales at low temperatures, passive to active oxidation transition, melting of oxide scales, changes in surface radiative properties, formation of porosity and changes in effective conductivity, surface catalytic recombination and transitions in catalytic properties, as well as high-temperature phase changes. The role of these processes in promoting thermochemical instabilities for the different material systems is discussed.

Ultra High Temperature Ceramics, UHTC

Mishaps with oxygen in NASA operations.

Oxygen safety programs were conducted, taking into consideration a review of the hazards, the available data concerning the failure of components and systems, and the oxygen handling procedures followed by NASA and its contractors. Information is presented regarding a substantial number of oxygen mishaps together with safety regulations aimed at reducing the accident probability. The information was used to establish categories of events causing the mishap. These categories include materials incompatibility deficiency, materials failure, design deficiency, cleaning deficiency, and procedural deficiencies. Mishaps are generally caused by a number of interacting factors.

Ordin, P. M.

Buckling and Failure of Compression-loaded Composite Cylindrical Shells with Reinforced Cutouts

Results from a numerical and experimental study that illustrate the effects of selected cutout reinforcement configurations on the buckling and failure response of compression-loaded composite cylindrical shells with a cutout are presented. The effects of reinforcement size, thickness, and orthotropy on the overall response of compression-loaded shells are described. In general, reinforcement around a cutout in a compression-loaded shell can retard or eliminate the local buckling response and material failure near the cutout and increase the buckling load of the shell. However, some results show that certain reinforcement configurations can cause a significant increase in the local interlaminar failures that can accumulate near the free edges of a cutout during a local buckling event.

Hilburger, Mark W.