Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “magnetron”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Subcritical-voltage magnetron RF power source

A system and method of operating a magnetron power source can achieve a broad range of output power control by operating a magnetron with its cathode voltage lower than that needed for free running oscillations (e.g., below the Kapitsa critical voltage or equivalently below the Hartree voltage) A sufficiently strong injection-locking signal enables the output power to be coherently generated and to be controlled over a broad power range by small changes in the cathode voltage. In one embodiment, the present system and method is used for a practical, single, frequency-locked 2-magnetron system design.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2021

Effects of sample bias on adhesion of magnetron sputtered Cr coatings on SiC

Swelling of SiC at 300 C due to in-service neutron irradiation causes tensile residual stresses in coatings which are expected to adversely affect the performance of coated SiC composite fuel cladding for light water reactors. Matching the coating swelling with the substrate, a solution common for thermal expansion, is not practical in the case of neutron irradiation. Biasing samples during magnetron sputtering deposition induces compressive residual stress which may counteract this. In this study, chromium coatings were deposited on SiC by DC magnetron sputtering with no external heating at bias voltages of –50V, –75V, and –100V. The effects of the bias voltage on morphology, residual stress, microstrain, texture, and adhesion are shown. The low deposition temperature resulted in the coating microstructure evolution following an energetic particle bombardment dominated trend. Additionally, at the two lower bias voltages knock-on implantation dominated increasing the residual stress and microstrain while at the highest bias voltage, thermal spike migration allowed for defect relaxation. When the knock-on induced compressive residual stress exceeded 0.8 GPa microcrack formation in the SiC substrate decreased coating adhesion. While no microcracks formed at the lowest bias voltage, insufficient atomic mobility during coating growth lead to voids forming in the coating. A balance is needed to form void-free coatings that have high compressive residual stress.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Influence of oxygen on the optical and electrical properties of magnetron-sputtered indium tin oxide thin films at ambient temperature

Indium Tin Oxide (ITO) thin films are commonly used as transparent conductive layers in the production of solar cells. ITO films are typically heat-treated at temperatures exceeding 200 °C after magnetron sputtering to optimize the physical, optical, and electrical characteristics for photovoltaic devices. Here, this high temperature heating procedure greatly limits the use of potential substrates, particularly those comprised of low-temperature-rated polymers. Herein, we examine the physical, optical, and electrical transport effects of oxygen:argon plasmas during radio frequency magnetron sputtering of ITO on glass and flexible polymer surfaces without subsequent heat treatment. ITO thin films were characterized via sheet resistance testing, UV-Vis spectroscopy, X-ray diffraction, and scanning electron microscopy imaging. Sheet resistance measurements revealed an increase in surface resistance with increasing oxygen concentration during sputtering. UV-Vis optical transmittance measurements demonstrated an improvement in optical transmittance with an increase in oxygen concentration reaching a maximum transmittance at an oxygen concentration of 1-2 %. Most importantly, it was discovered that producing bilayers of ITO with pure argon sputtered plasmas followed by oxygen:argon plasmas produced ITO thin films with suitable resistance and transmittance without the need for high temperature post annealing. These results highlight a methodology for the deposition of ITO thin films on temperature sensitive substrates for flexible photovoltaics and low-cost module production.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Boron carbide films with reduced nodular defect density deposited by full-face erosion radio-frequency magnetron sputtering

Boron carbide coatings deposited by sputtering with conventional planar magnetrons exhibit nodular growth defects. Here, we demonstrate that the density of nodular defects in B 4 C films can be greatly reduced by using a full-face-erosion magnetron source that achieves a more uniform target erosion by sweeping the confining magnetic field over the target surface. Here, we systematically study properties of B 4 C films deposited on substrates with different tilt angles and demonstrate deposition of ultrathick films with compressive residual stress below 200MPa.

36 MATERIALS SCIENCE↗
DOE OSTI2025

High-rate magnetron sputter deposition of low-stress boron carbide films on tilted substrates

Boron carbide is attractive for several applications, including nuclear fuel capsules for inertial confinement fusion (ICF). The fabrication of ICF capsules involves the deposition of ultrathick coatings with density and thickness uniformity on submicron length scales on non-planar (spherical) substrates. Such a deposition requires control of the deposition rate, residual stress, and film microstructure. Here, we systematically study the direct-current magnetron sputter deposition of B 4 C coatings with a full-face-erosion magnetron source as a function of substrate tilt and Ar working gas pressure. Film properties are correlated with results of plasma diagnostics and predictions of Monte Carlo simulations of ballistic sputtering and gas-phase transport. The fabrication of low-stress amorphous B 4 C films with deposition rates of 7μm/h is demonstrated.

Kawasaki, K. [Lawrence Livermore National Laborato↗
DOE OSTI2021

Electron dynamics in radio frequency magnetron sputtering argon discharges with a dielectric target

Abstract We demonstrate a self-consistent and complete description of electron dynamics in a typical electropositive radio frequency magnetron sputtering (RFMS) argon discharge with a dielectric target. The electron dynamics, including the electron power absorption dynamics in one radio frequency (RF) period, is studied via a fully kinetic 2d3v particle-in-cell/Monte Carlo collision (PIC/MCC) electrostatic simulation. The interplay between the fundamental plasma parameters is analyzed through their spatiotemporal dynamics. Due to the influence of magnetic trap on the electron transport, a spatially dependent charging that perturbs the electric potential is observed on the dielectric target surface, resulting in a spatially dependent ion energy distribution along the target surface. The E × B drift-to-discharge current ratio is in approximate agreement with Bohm diffusion. The electron power absorption can be primarily decoupled into the positive Ohmic power absorption in the bulk plasma region and the negative pressure-induced power absorption near the target surface. Ohmic power absorption is the dominant electron power absorption mechanism, mostly contributed by the azimuthal electron current. The power absorption due to electron inertial effects is negligible on time-average. Both the maximum power absorption and dissipation of electrons appear in the bulk plasma region during the second half of the RF period, implying a strong electron trapping in magnetron discharges. The contribution of secondary electrons is negligible under typical RFMS discharge conditions.

Physics↗
DOE OSTI2023

Radio-frequency magnetron sputter deposition of ultrathick boron carbide films

The deposition of thick B 4 C films with low residual stress by conventional direct-current magnetron sputtering is accompanied by the formation of dust particulates contaminating the target, chamber, and substrates and leading to the formation of nodular defects in films. Here, we demonstrate that the formation of particulates is greatly reduced during radio-frequency magnetron sputtering (RFMS). We systematically study properties of B 4 C films deposited by RFMS with a substrate temperature of 330 °C, a target-to-substrate distance of 10 cm, Ar working gas pressure in the range of 4.5–12.0 mTorr (0.6–1.6 Pa), and substrate tilt angles of 0°–80°. All films are x-ray amorphous. A columnar structure develops with increasing either Ar pressure or substrate tilt. For columnar films, the column tilt angle decreases with increasing Ar pressure, which we attribute to a corresponding increase in the width of the distribution of impact angles of deposition flux. In contrast to the Keller–Simmons rule, the deposition rate increases with increasing Ar pressure, which suggests a better coupling of the RF energy to the plasma processes that lead to target sputtering at higher pressures. There is a critical substrate tilt angle above which the total residual stress is close to zero. This critical substrate tilt angle is ~0° for an Ar pressure of 12 mTorr (1.6 Pa). The lower residual stress state, necessary for depositing ultrathick films, is characterized by a larger concentration of nanoscale inhomogeneities and decreased mechanical properties. Based on these results, RFMS deposition of 60-μm-thick B 4 C films is demonstrated.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Lithium nitride coatings deposited by magnetron sputtering on sulfide electrolytes for solid-state batteries

Lithium nitrides have been considered as promising candidates for interfacial layers in solid-state lithium batteries (SSBs). Previously reported lithium nitride (Li 3 N) coatings were mostly prepared by the reaction between lithium metal and nitrogen gas, which makes it challenging for their thickness control and integration in SSBs. In this study, we prepare Li 3 N via magnetron sputtering for the first time, and apply the resulting coating directly on sulfide solid-state electrolyte. A much smaller impedance increase associated with improved cycling performance is observed in lithium metal symmetric cell. These results demonstrate the feasibility of depositing Li 3 N via magnetron sputtering and its application in SSBs.

25 ENERGY STORAGE↗
DOE OSTI2024

Anomalous Retrograde Drifts in Obstructed Magnetron Microdischarges: a Consequence of a Field Reversal in the Anode Sheath?

The goal of this project was to carry out experiments at the Plasma Collaborative Research Facility (Princeton Plasma Physics Laboratory) aimed at confirming or refuting the hypothesis that an electric field reversal occurs in the near-anode region of a strongly obstructed planar magnetron microdischarges. Magnetron discharges are magnetized plasmas with E x B field topologies, and variants of such discharges are widely used in materials processing. The topologies are also similar to that of Hall thrusters used in space propulsion. Understanding the structure of these discharges will aid in developing reliable simulations that are intended to facilitate the further development of such technologies, as the field reversals, presumed to be due to strong axial-driven electron transport, provides further insight into transport properties. The possible existence of such a field reversal is hinted at because of the retrograde-propagating (i.e., negative E x B) spokes or gradient-driven drift instabilities seen in the high speed videos and segmented anode probing of the plasma. The presence of this field reversal should be reflected in the ion dynamics, particularly, in an ion drift towards the anode. The proposed experiments to be conducted at the PCRF are to characterize this anode-directed ion drift using state-of-the-art laser-induced fluorescence velocimetry. In particular, we seek to see if the near-anode ion velocity reverses direction when the external circuit is varied to alter the electron current demand imposed at the anode. Such an ion velocity reversal would confirm the mechanism, which is that the highly obstructed (small gapped) discharge produces strong axial gradients in plasma density, driving more electrons towards the anode then that demanded by the external circuit.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1969

Magnetron tuner has locking feature

Magnetron tuning arrangement features a means of moving a tuning ring axially within an anode cavity by a system of reduction gears engaging a threaded tuning shaft of lead screw. The shaft positions the tuning ring for the desired magnetron output frequency, and a washer prevents backlash.

Martucci, V. J.↗
NASA NTRS1985

Magic-T-Coupled Magnetrons

Outputs of two magnetrons added coherently in scheme based on resonant waveguide coupling and injection phase locking. In addition, filaments are turned off after starting. Overall effect is relatively-inexpensive, lowpower, noisy magnetrons generate clean carrier signals of higher power that ordinarily require more expensive klystrons.

Dickinson, R. M.↗
NASA NTRS1984

Magnetron Sputtered Gold Contacts on N-gaas

Direct current planar magnetron sputtering was used to deposit gold Schottky barrier electrical contacts on n-type GaAs of varying doping densities. The electrical character of the contact was determined from current voltage and electron beam induced voltage data. Without reducing the surface concentration of carbon and oxide, the contacts were found to be rectifying. There is evidence that energetic neutral particles reflected from the magnetron target strike the GaAs and cause interfacial damage similar to that observed for ion sputtering. Particle irradiation of the surface during contact deposition is discussed.

Buonaquisti, A. D.↗
NASA NTRS1990

Effects of an unbalanced magnetron in a unique dual-cathode, high rate reactive sputtering system

Simple plasma and magnetic field measurements are presented to illustrate the opportunities afforded by using unbalanced magnetrons in a dual-cathode system. The system employs a pair of opposed cathodes, 38 cm x 13 cm, placed 27.5 cm apart, to coat specimens mounted on a rotational substrate holder. Comparisons are drawn between the original 'balanced' magnetron and several unbalanced configurations in terms of field strengths, deposition rates, etching characteristics, and substrate ion current densities for the growth of TiN films. The effects of 'unbalancing' on the nature of the plasma within the 3D geometry of the deposition chamber are elucidated via plasma probe and magnetic field studies performed under a variety of conditions. All the unbalanced configurations examined provided enhanced ion bombardment at the surface of the growing film. The closed-field or opposed magnet geometry resulted in a threefold or greater increase in current density when compared with that obtained using the corresponding mirrored geometry under the same conditions.

Rohde, S. L.↗
NASA NTRS2014

A Magnetron Sputter Deposition System for the Development of Multilayer X-Ray Optics

The proposal objective is to establish the capability to deposit multilayer structures for x-ray, neutron, and EUV optic applications through the development of a magnetron sputtering deposition system. A specific goal of this endeavor is to combine multilayer deposition technology with the replication process in order to enhance the MSFC's position as a world leader in the design of innovative X-ray instrumentation through the development of full shell replicated multilayer optics. The development of multilayer structures is absolutely necessary in order to advance the field of X-ray astronomy by pushing the limit for observing the universe to ever increasing photon energies (i. e. up to 200 keV or higher); well beyond Chandra (approx. 10 keV) and NuStar's (approx. 75 keV) capability. The addition of multilayer technology would significantly enhance the X-ray optics capability at MSFC and allow NASA to maintain its world leadership position in the development, fabrication and design of innovative X-ray instrumentation which would be the first of its kind by combining multilayer technology with the mirror replication process. This marriage of these technologies would allow astronomers to see the universe in a new light by pushing to higher energies that are out of reach with today's instruments.To this aim, a magnetron vacum sputter deposition system for the deposition of novel multilayer thin film X-ray optics is proposed. A significant secondary use of the vacuum deposition system includes the capability to fabricate multilayers for applications in the field of EUV optics for solar physics, neutron optics, and X-ray optics for a broad range of applications including medical imaging.

Broadway, David↗
NASA NTRS2015

A Magnetron Sputter Deposition System for the Development of X-Ray Multilayer Optics

The project objective is to establish the capability to deposit multilayer structures for x-ray, neutron, and extreme ultraviolet (EUV) optic applications through the development of a magnetron sputtering deposition system. A specific goal of this endeavor is to combine multilayer deposition technology with the replication process in order to enhance NASA Marshall Space Flight Center's (MSFC's) position as a world leader in the design of innovative x-ray instrumentation through the development of full shell replicated multilayer optics. The development of multilayer structures are absolutely necessary in order to advance the field of x-ray astronomy by pushing the limit for observing the universe to ever-increasing photon energies (i.e., up to 200 keV or higher), well beyond Chandra's (approx.10 keV) and NuStar's (approx.75 keV) capability. The addition of multilayer technology would significantly enhance the x-ray optics capability at MSFC and allow NASA to maintain its world leadership position in the development, fabrication, and design of innovative x-ray instrumentation, which would be the first of its kind by combining multilayer technology with the mirror replication process. This marriage of these technologies would allow astronomers to see the universe in a new light by pushing to higher energies that are out of reach with today's instruments. To this aim, a magnetron vacuum sputter deposition system for the deposition of novel multilayer thin film x-ray optics is proposed. A significant secondary use of the vacuum deposition system includes the capability to fabricate multilayers for applications in the field of EUV optics for solar physics, neutron optics, and x-ray optics for a broad range of applications including medical imaging.

Broadway, David↗
DOE OSTI2020

Superlattice-Structured Films by Magnetron Sputtering as New Era Electrodes for Advanced Lithium-ion Batteries

Sustaining sound structures in Si-based anodes is extremely challenging because of the high volumetric expansion that occurs upon cycling. To maintain high capacities over cycles, new designs rely on engineering-specific hierarchical geometries and/or optimized composite compositions such that at least one of the multiple elements serves as buffer and/or electron conductive pathways in the electrodes. In this paper, we report an innovative design in which alternating layers of periodic atomic structures involving multiple elements form a new anode material for lithium-ion batteries. In this work, a superlattice-structured amorphous film made using Si, Mo, and Cu is fabricated by a simple and scalable magnetron sputtering process for the first time. This continuous and repetitive superlattice formation along the film thickness provides a homogeneous stress-strain distribution. The Mo-Cu layer in the superlattice acts as an inactive-conductive layer and as a backbone to handle the volume expansion of active Si upon cycling. This nano-functional superlattice approach enables harnessing the high energy density of Si while maintaining its structural stability. As a result, the electrode exhibits high specific capacity and capacity retention even at high cycling rates. The possible use of the film in a full cell is also evaluated by cycling it vs. the LiMn 1.5 Ni 0.5 O 4 cathode. The full cell maintains a stable capacity of about 900 mAh g anode -1 over 150 cycles, at ~600 mA g -1 rate. The remarkable performance of this nano-functional superlattice film is found to be promising as anodes for applications that require high energy, long calendar life, and excellent abuse tolerance such as electric vehicle batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Probing layered structure of Inconel 625 coatings prepared by magnetron sputtering

Coating/substrate interface and oxide layers present in Inconel 625 film may cause significant impacts on its corrosion behavior. However, layered structure of Inconel 625 coatings remains poorly understood due to its requirement of high spatial resolution. Here we have applied X-ray reflectometry (XRR) to probe the layered structure of magnetron-sputtered Inconel 625 film with atomic spatial resolution. Our results indicate that there exists a 2 nm thick Cr-rich Inconel sublayer underneath the principal film. On top of the principal film, it is found a 2 nm thick oxide layer mainly consisting of NiO. In addition, we detected ~2 Å contamination layer on the sapphire substrate, although argon ion sputter cleaning had been applied to the substrate prior to deposition. By comparing the coatings with different deposition time, we observed that the thickness of principal Inconel 625 layer grows linearly with deposition time, with all other layers remaining constant. Our findings provide insight into the layered structures of Inconel 625 coatings with atomic-scale spatial resolution, and provide directions for future efforts that aim to improve the corrosion resistance of Inconel 625 coatings.

14 SOLAR ENERGY↗
DOE OSTI2019

Easy Controlled Properties of Quaternary FeNiCrCd Thin Films Deposited from a Single dc Magnetron Sputtering Under the Influence of Deposition Rate

The quaternary FeNiCrCd thin films were produced from a single FeNiCrCr source on a commercial flexible polymer substrate using one dc magnetron sputtering technique. For that, a series of the films with a thickness of 50 nm were produced at different deposition rates of 0.02, 0.04, 0.06, and 0.08 nm/s, separately. In this study, as far as concerned, this was the first time that structural and magnetic properties of FeNiCrCd thin films were investigated. According to compositional analysis, the Fe and Cr contents slightly decreased with increasing deposition rate while Ni was almost constant, whereas those of the amount of Cd atoms increased. However, the atomic amounts of Fe and Cd in the films are quite different from those of the source material. The change of the atomic contents in the films from the source may be attributed to the relatively different bond energy/melting point of metals which have different contents sputtered from source material since this physical parameter is very significant for the sputtering process. For crystal structural analysis, a combination of hexagonal close-packed (hcp) and body-centered cubic (bcc) were observed. The peak intensity of the bcc-dominated planes decreased while the hcp-dominant plane increased since the change in peak intensities is compatible with the compositional analysis with increasing deposition rate. And, the grain sizes decreased gradually from 40.1 to 23.4 nm, with increasing deposition rate from 0.02, to 0.08 nm/s. Also, the film surfaces transformed from a rough to smooth surfaces with decreasing grain sizes as deposition rate increased. For magnetic analysis, the saturation magnetization M{sub s} values decreased as 1030, 773, 730, and 217 emu/cm{sup 3} with increasing deposition rate as 0.02, 0.04, 0.06, and 0.08 nm/s, respectively. In the same manner, the coercivity H{sub c} values were found as 11, 7, 6, and 2 Oe with the deposition rate of 0.02, 0.04, 0.06, and 0.08 nm/s, respectively. The decrease of the H{sub c} may have primarily come from the transformation of rough to smooth surface of the films. It may also be said that the films showed soft magnetic properties due to their low H{sub c} values with increasing deposition rate. Thus, the magnetic properties of the quaternary FeNiCrCd alloy films were seen to be easily improved with the deposition rate parameter for potential use in different industrial applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗