Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “low Pt loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Fuel Cell Membrane Electrode Assemblies with Ultra-Low Pt Nanofiber Electrodes (Final Report)

H 2 /air fuel cell membrane-electrode-assemblies (MEAs) were fabricated with electrospun particle/polymer nanofiber mat cathodes (0.1 mg Pt /cm 2 or 0.2 mg Pt /cm 2 Pt/C, PtCo/C or PtNi/C) and anodes (0.1 mg/cm 2 Pt/C), where the binder was a mixture of acid-form perfluorosulfonic acid ionomer (e.g., Nafion™) and poly(acrylic acid) (PAA) carrier polymer or sodium-form PFSA with a carrier polymer of either PAA or polyethylene oxide (PEO). For the latter two cases, the water-soluble carrier was removed from the fibers after electrospinning. MEAs with Pt/C anode/cathode catalyst loadings of 0.1 mg Pt /cm2 each, an 1100 EW PFSA binder (Nafion™ dispersion), and a Nafion 211 membrane produced high power at both high and low relative humidity (RH) conditions, e.g., a maximum power density of 919 mW/cm 2 at 100% RH and 832 mW/cm 2 at 40% RH for a test at 80 °C and 200 kPa abs . The high power at low RH was attributed to nm-size pores within the fibers that trap water via capillary condensation thus maintaining a high proton conductivity of the PFSA binder in the cathode and especially the anode while minimizing/eliminating ionic isolation of catalyst particles in low water content, poorly conductive binder. At the same time, micro-porosity between fibers in the cathode allows for fast removal of electrogenerated water, thus minimizing cathode flooding. Nanofiber MEAs with Pt alloy catalyst cathodes also performed well, where a fibrous PtCo/C catalyst cathode at a loading of 0.1 mg/cm 2 produced 20% more power than a conventional powder cathode MEA, e.g., a maximum power density of 1,045 mW/cm 2 vs. 869 mW/cm 2 at 80 °C, 100% RH, and 200 kPa abs , and a PtNi/C fiber cathode MEAs prepared with Na+-form Nafion + PEO generated a maximum power of 820 mW/cm 2 at 40% RH. Fiber electrode MEAs with a neat Nafion binder (prepared from Na+-form Nafion + PEO or PAA) where the cathode Pt loading was ~0.1 mg/cm 2 exhibited a 25% loss in maximum power at 30,000 metal dissolution cycles, as compared to a 12% loss when the cathode binder was H+-form Nafion + PAA. The performance of a fiber mat electrode MEA with Pt/C catalyst (0.2 mg/cm 2 cathode loading and 0.1 mg/cm 2 anode loading) was excellent. At 80 oC and 200 kPa abs , the maximum power density was 1104 mW/cm 2 . The maximum power was independent of feed gas humidity for 40 < RH < 100%. The power loss after a metal dissolution AST (30,000 voltage cycles) was only 13%.

08 HYDROGEN↗
DOE OSTI2022

MemGaze: Rapid and Effective Load-Level Memory Trace Analysis

A major challenge of memory analysis tools is combining high-resolution analysis and low overhead measurement. Currently, hardware/software-based analysis of load-level sequences incurs time slowdowns of O(100×). We present MemGaze, a tool for low-overhead, high-resolution memory analysis. MemGaze uses Intel’s Processor Tracing (PT) instruction ptwrite to collect sampled and compressed memory address traces for load-level, sequence-aware analysis of data reuse. We describe multi-resolution analysis for locations vs. operations, accesses vs. spatio-temporal reuse, and reuse (distance, rate, volume) vs. access patterns. Both trace size and resolution are controllable. We use MemGaze to elucidate the memory effects of different data structures and algorithms. For sampled traces that are ˜1% of a full one, analysis metrics have 1-25% MAPE for histograms of varying dynamic sequence lengths. With current suboptimal kernel support (PT runs continuously), MemGaze’s time overhead is typically 10–95%; 7× at worst. However, when PT runs only during samples, overhead is 10–35% on memory intensive regions and correlates with executed ptwrites.

Kilic, Ozgur O.↗
DOE OSTI2022

Low temperature dry reforming of methane using Ru-Ni-Mg/ceria-zirconia catalysts: Effect of Ru loading and reduction temperature

Dry reforming catalysts, especially those with activity at moderate temperatures, have been intensely investigated to enhance the conversion of biogas. Here, Ru is evaluated as a promoter for Ni-Mg based catalysts. Catalysts based on 1.4 wt%Ni-1.0 wt%Mg-Ce 0.6 Zr 0.4 O 2 with Ru (0.02–0.32 wt%) were prepared using incipient wetness. The reducibility of the catalysts and conversions increased with increasing Ru content. Increases in conversions with increasing Ru loading was attributed to the additional active sites and synergistic effect between Ru and Ni, which weakened Ni-Mg interactions. Samples showed dry reforming activity at low temperatures (450–510 °C). Reaction rates and activation energies of higher loading Ru samples (1.4 wt%Ni-1.0 wt%Mg/Ce 0.6 Zr 0.4 O 2 with 0.16 and 0.32 wt%Ru) decreased when the reduction temperature was raised from 300 to 400 °C. A 20 h TOS study showed stable catalytic activity with minimal coke deposition. Furthermore, the results suggest that Ru is an alternative to Pt in promoting low temperature dry reforming of methane.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Low temperature water-gas shift: Optimization of K loading on Pt/m-ZrO 2 for enhancing CO conversion

Previous work showed that alkali doping of Pt/ZrO 2 significantly improved the LT-WGS rate. This improvement was caused by an acceleration in the rate of formate decomposition, the rate limiting step of an associative mechanism, through electronically weakening the CH bond. In this study, the effects that potassium loading on Pt/ZrO 2 have on the rate of LT-WGS and the strength of the CH bond in intermediate formate species are explored. Catalysts were investigated using in-situ DRIFTS, TPR-MS, TPD, EXAFS, and catalyst testing. Here, loadings of 1.7 wt.% potassium or higher shifted the formate ν(CH) band to significantly lower wavenumbers, indicating weakening of the bond. For the optimal loading, 2.6 wt.% K, the formate CH bond was significantly weakened, and the surface of Pt nanoparticles remained largely uncovered. However, loadings of 3.4 wt. % and above blocked the surface of the platinum nanoparticles. This, in addition to an increasing average Pt0 cluster size, hindered platinum from assisting in dehydrogenation of formate during steam promoted formate decomposition occurring in LT-WGS.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Atomically Dispersed Pentacoordinated‐Zirconium Catalyst with Axial Oxygen Ligand for Oxygen Reduction Reaction

Single-atom catalysts (SACs), as promising alternatives to Pt-based catalysts, suffer from the limited choice of center metals and low single-atom loading. Here, we report a pentacoordinated Zr-based SAC with nontrivial axial O ligands (denoted O-Zr-N-C) for oxygen reduction reaction (ORR). The O ligand downshifts the d-band center of Zr and confers Zr sites with stable local structure and proper adsorption capability for intermediates. Consequently, the ORR performance of O-Zr-N-C prominently surpasses that of commercial Pt/C, achieving a half-wave potential of 0.91 V vs. reversible hydrogen electrode and outstanding durability (92% current retention after 130-hour operation). Moreover, the Zr site shows good resistance towards aggregation, enabling the synthesis of Zr-based SAC with high loading (9.1 wt%). With the high-loading catalyst, the zinc-air battery (ZAB) delivers a record-high power density of 324 mW cm -2 among those of SAC-based ZABs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

A red-light-powered silicon nanowire biophotochemical diode for simultaneous CO 2 reduction and glycerol valorization

A bias-free photochemical diode, in which a p-type photocathode is connected to an n-type photoanode to harness light for driving photoelectrochemical reduction and oxidation pairs, serves as a platform for realizing light-driven fuel generation from CO 2 . However, the conventional design, in which cathodic CO 2 reduction is coupled with the anodic oxygen evolution reaction (OER), requires substantial energy input. Here we present a photochemical diode device that harnesses red light (740 nm) to simultaneously drive biophotocathodic CO 2 -to-multicarbon conversion and photoanodic glycerol oxidation as an alternative to the OER to overcome the above thermodynamic limitation. The device consists of an efficient CO 2 -fixing microorganism, Sporomusa ovata, interfaced with a silicon nanowire photocathode and a Pt–Au-loaded silicon nanowire photoanode. This photochemical diode operates bias-free under low-intensity (20 mW cm –2 ) red light irradiation with ~80% Faradaic efficiency for both the cathodic and anodic products. Finally, this work provides an alternative photosynthetic route to mitigate excessive CO 2 emissions and efficiently generate value-added chemicals from CO 2 and glycerol.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Electrospun Nanofiber Electrodes for High and Low Humidity PEMFC Operation

MEAs with nanofiber mat electrodes containing Pt/C catalyst and Nafion binder were fabricated and evaluated. The electrodes were prepared by electrospinning a solution of catalyst powder, salt-form Nafion (with Na + , Li + , or Cs + as the sulfonic acid counterion), and a carrier polymer of either polyethylene oxide or poly(acrylic acid). The carrier polymer was extracted prior to MEA testing by a hot water soaking step. The resulting fibers were 15%–17% porous, with a core–shell-like morphology (a coating of primarily Nafion on the fiber surface). MEAs with anode/cathode catalyst loadings of 0.1 mg Pt cm −2 each and a Nafion 211 membrane produced high power at both high and low relative humidity (RH) conditions in H 2 /air fuel cell tests, e.g., a maximum power density of 919 mW cm −2 at 100% RH and 832 mW cm −2 at 40% RH for a test at 80 °C and 200 kPa abs . The presence of nm-size pores within the fibers trapped water via capillary condensation during low RH feed gas testing, thus maintaining a high proton conductivity of the Nafion binder in the anode and cathode while minimizing/eliminating ionic isolation of catalyst particles in low water content, poorly conductive binder.

25 ENERGY STORAGE↗
DOE OSTI2025

Fabrication of porous transport electrodes: Development of quantitative approach for quality control

This work focuses on porous transport electrodes (PTEs), which integrate the anodic catalyst with the adjacent Ti porous transport layer (PTL). Challenges in catalyst deposition on PTLs, particularly at low loadings, motivated this study to evaluate various fabrication methods and characterization approaches. This work investigated Pt-treated PTLs coated with Ir-based catalysts using several common methods, including airbrush coating, rod coating, ultrasonic spray coating, electrodeposition, and sputter deposition, with catalyst loadings ranging from 2.9 to 0.1 mg/cm 2 , providing the opportunity for comparisons across a large set of samples produced by different methods. Two widely accessible characterization techniques: X-ray computed tomography (XCT) and scanning electron microscopy energy dispersive X-ray spectroscopy (SEM-EDS) were explored. Initial evaluation of selected samples with XCT provided qualitative insights into catalyst distribution, however comprehensive quantitative analysis was limited. SEM-EDS enabled detailed information on the catalyst distribution both qualitatively and quantitatively using two metrics. Atomic and surface area % ratios of Pt:Ir and Ti:Ir revealed trends in catalyst loading and losses into the PTL pores, as well as evaluating the homogeneity of catalyst coatings. The analysis demonstrated that ultrasonic spray coating, electrodeposition, and sputter coating produced the most homogeneous coatings, with minimal catalyst losses observed for electrodeposition and sputter coating. By adapting common techniques with novel, standardized methodologies, this work establishes a universally applicable framework for cross-study comparison of PTEs. The SEM-EDS approach provides a practical, accessible tool for PTE characterization and contributes a reference dataset supporting both research development and rapid quality control.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

High protonic resistance of hydrocarbon-based cathodes in PEM fuel cells under low humidity conditions: Origin, implication, and mitigation

Hydrocarbon-based electrodes for proton-exchange membrane fuel cells face challenges in closing the performance gap with electrodes based on perfluorosulfonic acid ionomers, particularly under low humidity conditions. Alongside increased oxygen transport resistance and higher kinetic-induced overpotentials, the protonic resistance of these fluorine-free electrodes is the primary hurdle to improved performance. This study systematically investigates the origin and impact of the cathode protonic resistance on fuel cell performance, utilizing sulfonated phenylated polyphenylenes as hydrocarbon ionomers. Electrochemical characterization at low relative humidity (≤50 %) reveal a high protonic resistance arising from both lower conductivity of the hydrocarbon thin film compared to the bulk membrane and increased cathode tortuosity at a gas transport-optimized ionomer to carbon (I/C) ratio of 0.2. The poor protonic resistance at low relative humidities leads to a non-homogeneous current distribution across the thickness of the cathode electrode, resulting in lower catalyst utilization. To address this issue, reducing the thickness of the cathode CL while maintaining a constant Pt loading (i.e., increasing the Pt on carbon ratio) significantly reduces protonic resistance. This improvement compensates for the kinetic disadvantages of highly loaded carbon particles and results in a considerable performance increase by 40 % at 0.75 V under low relative humidities.

25 ENERGY STORAGE↗
DOE OSTI2025

Bridging interfacial properties and cell performance: A multiscale model for proton-exchange-membrane fuel cells

Here, to elucidate the impact of local interfaces on mass-transport resistance and overall cell performance of low-loaded proton-exchange-membrane fuel cells (PEMFCs), we present a multiscale modeling framework incorporating a novel modified agglomerate model. The model considers three distinct Pt-electrolyte interfaces: Pt on the carbon surface covered by either ionomer or water film and Pt inside carbon nanopores. Detailed mass-transport voltage-loss breakdowns reveal that coupled agglomerate-interface-scale mass transport dominates the mass-transport loss. The ionomer poisons the exterior-Pt surface through suppressing O 2 adsorption and intrinsic ORR activity, leading to low current-density performance. Conversely, interior-Pt interface enhances the kinetic performance but limits high current-density performance due to its low interfacial permeability. The exterior-Pt/water interface demonstrates superior kinetic performance and mass transport, though its practical implementation requires ensuring proton transport. By coupling the multiscale CL properties with ink parameters, the model identifies an optimal I to C ratio of approximately 0.5, a moderate value where the ionomer content is sufficient to guarantee proton transport without fully covering the Pt surface and forming large agglomeration, thus allowing the utilization of the Pt-water interface and avoiding high mass-transport loss. Overall, the model helps unravel limiting phenomena across different operating regimes and provides routes for optimizing performance.

Cell diagnostic↗
DOE OSTI2021

Understanding how single-atom site density drives the performance and durability of PGM-free Fe–N–C cathodes in anion exchange membrane fuel cells

One of the most important needs for the future of low-cost fuel cells is the development of highly active platinum group metal (PGM)-free catalysts. For the oxygen reduction reaction, Fe–N–C materials have been widely studied in both acid and alkaline media. However, reported catalysts in the literature show quite different intrinsic activity and in-cell performance, despite similar synthesis routes and precursors. Here, two types of Fe–N–C are prepared from the same precursor and procedure – the main difference is how the precursor was handled prior to use. It is shown that in one case Fe overwhelmingly existed as highly active single-metal atoms in FeN4 coordination (preferred), while in the other case large Fe particles coexisting with few single metal atoms were obtained. As a result, there were drastic differences in the catalyst structure, activity, and especially in their performance in an operating anion exchange membrane fuel cell (AEMFC). Additionally, it is shown that catalyst layers created from single-atom-dominated Fe–N–C can have excellent performance and durability in an AEMFC using H 2 /O 2 reacting gases, achieving a peak power density of 1.8 W cm -2 – comparable to similar AEMFCs with a Pt/C cathode – and being able to operate stably for more than 100 h. Finally, the Fe–N–C cathode was paired with a low-loading PtRu/C anode electrode to create AEMFCs (on H 2 /O 2 ) with a total PGM loading of only 0.135 mg cm -2 (0.090 mg Pt cm -2 ) that was able to achieve a very high specific power of 8.4 W mg PGM -1 (12.6 W mg Pt< sup>-1 ).

36 MATERIALS SCIENCE↗
DOE OSTI2020

Atomic Layer Deposition Overcoating Improves Catalyst Selectivity and Longevity in Propane Dehydrogenation

Propylene, a precursor for commodity chemicals and plastics, is produced by propane dehydrogenation (PDH). An increase in PDH yield via added catalyst activity, lifetime, or selectivity represents significant energy and economic savings. Using Pt dispersed on Al2O3 extrudate supports as a commercially relevant model system, we demonstrate that atomic layer deposition (ALD) metal oxide overcoats, used to tailor metal-active sites, can increase PDH yield and selectivity. We investigate the interplay of Pt loading, ALD overcoat thickness, and Al 2 O 3 support surface area on PDH activity, selectivity, and catalyst stability to show that applying a 6-8 A thick layer of Al 2 O 3 on low-surface area Al 2 O 3 supports of similar to 90 m 2 /g surface area yields the optimal combination of stability and activity, while increasing propylene selectivity from 91 to 96%. Increased stability upon steaming deactivation occurs because the Al 2 O 3 overcoat prevents the Pt nanoparticles from sintering. We speculate that the ALD overcoat selectively binds to the undercoordinated sites on the Pt nanoparticles, while leaving the more selective terrace sites available for dehydrogenation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Development of an Electrochemical Hydrogen Contaminant Detector

Hydrogen refueling stations (HRSs) that dispense hydrogen to fuel cell vehicles need to ensure the quality of hydrogen to avoid contamination of the vehicle’s expensive fuel cell stacks. Currently, stations verify their fuel quality only periodically to ensure that they meet the strict fuel quality standards specified by either International Organization for Standards (ISO) or Society for Automotive Engineers (SAE). The development of hydrogen contaminant detectors (HCDs) that can provide low cost continuous monitoring at the HRS can be an invaluable asset in protecting fuel cell vehicles from any fuel contamination in-between infrequent expensive analysis of hydrogen fuel quality. An HCD capable of detecting < 200 ppb of CO in hydrogen is presented in this paper. The HCD is based on an electrochemical hydrogen pumping cell whose ultra-low loaded working electrode is poisoned by the contaminant, thus reducing its hydrogen oxidation reaction rate. The hydrogen pumping cell consists of a Nafion® membrane, a sputtered Pt working electrode, a Pt/Ru counter/pseudo-reference electrode and an internal water wicking system that provides humidification to the membrane and electrodes. When this HCD is operated in a pulsed voltammetry mode, it can provide stable CO response for thousands of hours in a HRS.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Electrochemically Grown Ultrathin Platinum Nanosheet Electrodes with Ultralow Loadings for Energy-Saving and Industrial-Level Hydrogen Evolution

Nanostructured catalyst-integrated electrodes with remarkably reduced catalyst loadings, high catalyst utilization and facile fabrication are urgently needed to enable cost-effective, green hydrogen production via proton exchange membrane electrolyzer cells (PEMECs). Herein, benefitting from a thin seeding layer, bottom-up grown ultrathin Pt nanosheets (Pt-NSs) were first deposited on thin Ti substrates for PEMECs via a fast, template- and surfactant-free electrochemical growth process at room temperature, showing highly uniform Pt surface coverage with ultralow loadings and vertically well-aligned nanosheet morphologies. Combined with an anode-only Nafion 117 catalyst-coated membrane (CCM), the Pt-NS electrode with an ultralow loading of 0.015 mg Pt cm -2 demonstrates superior cell performance to the commercial CCM (3.0 mg Pt cm -2 ), achieving 99.5% catalyst savings and more than 237-fold higher catalyst utilization. The remarkable performance with high catalyst utilization is mainly due to the vertically well-aligned ultrathin nanosheets with good surface coverage exposing abundant active sites for the electrochemical reaction. Overall, this study not only paves a new way for optimizing the catalyst uniformity and surface coverage with ultralow loadings but also provides new insights into nanostructured electrode design and facile fabrication for highly efficient and low-cost PEMECs and other energy storage/conversion devices.

42 ENGINEERING↗
DOE OSTI2024

Dynamic Behavior of Pt Multimetallic Alloys for Active and Stable Propane Dehydrogenation Catalysts

Improving the use of platinum in propane dehydrogenation catalysts is a crucial aspect to increasing the efficiency and sustainability of propylene production. A known and practiced strategy involves incorporating more abundant metals in supported platinum catalysts, increasing its activity and stability while decreasing the overall loading. Here, using colloidal techniques to control the size and composition of the active phase, we show that Pt/Cu alloy nanoparticles supported on alumina (Pt/Cu/Al 2 O 3 ) displayed elevated rates for propane dehydrogenation at low temperature compared to a monometallic Pt/Al 2 O 3 catalyst. We demonstrate that the enhanced catalytic activity is correlated with a higher surface Cu content and formation of a Pt-rich core and Cu-rich shell that isolates Pt sites and increases their intrinsic activity. However, rates declined on stream because of dynamic metal diffusion processes that led to a more uniform alloy structure. This transformation was only partially inhibited by adding excess hydrogen to the feed stream. Instead, cobalt was introduced to provide trimetallic Pt/Cu/Co catalysts with stabilized surface structure and stable activity and higher rates than the original Pt/Cu system. In conclusion, the structure–activity relationship insights in this work offer improved knowledge of propane dehydrogenation catalyst development featuring reduced Pt loadings and notable thermal stability for propylene production.

Alloys↗
DOE OSTI2026

Quantification of [MTBD][beti] loading and its effects on Pt/HSC electrode performance in hydrogen fuel cells

High surface area carbon-supported platinum catalysts (Pt/HSC) are widely used in polymer electrolyte membrane fuel cells but often suffer from limited proton and oxygen transport within porous domains. To address these challenges, we integrate the ionic liquid [MTBD][beti] into Pt/HSC catalyst layers using two deposition methods-one-pot and sequential deposition-to tune IL distribution within micropores and mesopores. A combination of ex situ and in operando techniques were employed to elucidate electrode structure-performance relationships across a range of IL loadings. Sequential deposition achieved more efficient pore filling and higher IL retention at lower IL:C ratios, enabling enhanced proton conductivity and protection of active sites. Compared to the IL-free Pt/HSC, IL-modified electrodes demonstrated up to 28% improvement in mass activity and enhanced high-current-density performance under low relative humidity, while maintaining comparable performance under humidified conditions. Electrochemical impedance spectroscopy and CO displacement experiments reveal that improvements are linked to reduced ionic resistance and lower sulfonate adsorption on Pt sites, rather than changes in electrochemical surface area. However, excessive IL loading leads to mass transport losses. These results highlight the importance of selective pore filling and efficient IL distribution in achieving kinetic gains without compromising ionic and gas transport.

08 HYDROGEN↗
DOE OSTI2026

Methanol Partial Oxidation on Cu(111) and PtCu(111) Single-Atom Alloy Surfaces: Effect of Surface Oxygen Coverage on Selectivity

The selective oxidation of methanol to formaldehyde on Cu surfaces is an important and well-studied reaction. However, a systematic analysis of product selectivity as a function of oxygen coverage on Cu(111) and Cu-based single-atom alloys (SAAs) has not been previously reported. In this work, we present a comprehensive investigation of deuterated methanol (CD 3 OH) partial oxidation on Cu(111) and 1% PtCu(111) SAA surfaces as a function of preadsorbed oxygen coverage. Temperature-programmed desorption (TPD) and X-ray photoelectron spectroscopy (XPS) reveal that isolated Pt atoms inhibit the initial surface oxidation of Cu(111) under low oxygen exposures. Despite this difference in oxidation kinetics, the product selectivity remains largely unaffected: on both Cu(111) and PtCu(111), formaldehyde (CD 2 O) is the predominant partial oxidation product over a broad range of oxygen coverages. The selectivity toward formaldehyde peaks at intermediate oxygen coverages (∼0.3 monolayers, ML), indicating the existence of an optimal oxygen loading for partial oxidation. Notably, the similar product selectivities on Cu(111) and PtCu(111) over a range of surface oxygen coverage indicate that Pt single atoms do not significantly alter the reaction pathway or shift the optimal oxygen coverage for formaldehyde formation. Control experiments confirm that Cu(111) is unreactive toward methanol in the absence of oxygen, while PtCu(111) surfaces produce a small amount of formaldehyde even when oxygen is not preadsorbed, indicating that isolated Pt atoms facilitate O−H activation at below 150 K, leading to H 2 desorption, followed by C−D activation at higher temperatures (∼350 K). Density functional theory (DFT)-based calculations show that Pt atoms increase the O 2 dissociation barrier relative to Cu(111), consistent with the observed inhibition of oxidation at low exposures. Overall, this work provides the first detailed selectivity map for methanol oxidation on oxidized Cu(111) and PtCu(111) SAA surfaces. By linking classical mechanistic insights such as methoxy- and formate-mediated pathways with single-atom alloy catalyst design, this work demonstrates that while Pt substitution modulates the oxidation kinetics and oxygen binding, the overall selectivity toward formaldehyde is governed primarily by oxygen coverage. These findings underscore the potential of isolated dopants to tune surface oxidation behavior without compromising the intrinsic partial oxidation selectivity of copper-based catalysts.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Rational design of high-performance low-loading oxygen reduction catalysts for alkaline fuel cells

The lack of mechanistic understanding and catalyst design principles for alkaline electrolytes, especially for the sluggish oxygen reduction reaction, has impeded the advancement of alkaline fuel cells. Here, in this study, we propose a modified volcano plot and apply this rationale to strategically design Pt nanosheets with PdH x nanosheets substrates. This catalyst exhibited high stability with a specific activity of 1.71 mA cm −2 at 0.95 V versus the reversible hydrogen electrode, surpassing the benchmark of Pt/C by 49-fold. Spectroscopic, electrochemical and electron microscopic characterizations revealed that such performance enhancement originated from tensile-strained Pt{111} facets, improving oxidative stability and suppressing carbon corrosion. In fuel cell testing, the catalyst enabled a peak power density of 1.67 W cm −2 with a loading of 10 µg PGM Cathode cm −2 . Further optimization delivered a peak power density of 21.7 W mg −1 PGM Cathode+Anode with a total specific catalyst cost US$\$$1.27 kW −1 , surpassing the US Department of Energy’s Pt group metal loading and cost targets. This study provides valuable insights into catalyst design for the alkaline oxygen reduction reaction.

36 MATERIALS SCIENCE↗