Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “lithium stripping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Final Scientific/Technical Report: Simultaneous Lithium Extraction and Thin-Film Deposition of Lithium Metal for Low-Cost, High-Energy Anodes from Brine Resources

This report describes the scale-up and pilot validation of Alpha-En's Reductive Lithium Extraction (RLE) process, which directly converts lithium ions from aqueous brine-derived feedstocks into thin-film lithium metal anodes, demonstrating greater than 50% extraction efficiency, battery performance matching or exceeding commercial lithium metal controls in coin and pouch cells, and continuous roll-to-roll production of a meter-scale lithium metal anode strip.

25 ENERGY STORAGE↗
DOE OSTI2023

Silver-carbon interlayers in anode-free solid-state lithium metal batteries: Current development, interfacial issues, and instability challenges

As an interlayer between the anode and the electrolyte of the all-solid-state lithium metal batteries (ASSLMBs), the silver-carbon (Ag-C) nanocomposite has been reported to significantly increase the energy density and cycle rate of solid-state lithium metal batteries. Ag-C interlayers serve as mixed ionic-electronic conductor that conducts both Li+ ions and electrons and lithium storage capacity. Unfortunately, it was unclear how the Ag-C interlayer regulated lithium plating and stripping. Moreover, the structural and chemical instabilities between the interlayer and the electrolyte, within the interlayer, or beneath the interlayer on lithium substrate are likely to cause cell failure. In this review, we discuss interfacial issues and summarize recent progress in solution strategies for ASSLMBs, with a specific focus on the use of a silver-carbon (Ag-C) nanocomposite interlayer in anode-free setups. Based on the Li transport kinetics among the Ag-C interlayers, the interfacial configurations of Ag-C interlayers are classified as either exterior or internal. Furthermore, the review concludes with a discussion of the perspectives and future prospects, allowing for the improvement of interlayer techniques for solid-state batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Understanding and controlling lithium morphology in solid polymer and gel polymer systems: mechanisms, strategies, and gaps

Lithium metal anode promises the highest theoretical energy density and may enable high energy designs such as lithium–sulfur and lithium–air batteries. However, stable lithium plating and stripping remains a challenge in all electrolyte systems including liquids, polymers, and ceramic electrolytes. In this perspective, we examine literature studies of lithium morphologies in solid polymer and gel polymer systems and compare that with well-studied liquid electrolytes. In solid polymer electrolytes, current density and mechanical properties are both governing parameters for lithium morphology, differing from conventional liquid electrolytes. Stable lithium electrodeposition may be accomplished by a polymer electrolyte with good stiffness operating at significantly lower current densities than its limiting current density, which is defined by the Sand equation. In gel polymer electrolytes, the reported lithium morphology is more similar to that in liquid electrolytes, suggesting similar nucleation and growth mechanisms. Based on experimental evidence and theoretical guidance, current strategies to control lithium morphology in solid polymer and gel polymer electrolytes are summarized. The limitations of these strategies are discussed. In particular, we note the knowledge gap in understanding the solid electrolyte interphase in solid polymer systems and the critical role it can play in regulating lithium morphologies.

36 MATERIALS SCIENCE↗
DOE OSTI2019

An ultrathin ionomer interphase for high efficiency lithium anode in carbonate based electrolyte

High coulombic efficiency and dendrite suppression in carbonate electrolytes remain challenges to the development of high-energy lithium ion batteries containing lithium metal anodes. Here we demonstrate an ultrathin (≤100 nm) lithium-ion ionomer membrane consisting of lithium-exchanged sulfonated polyether ether ketone embedded with polyhedral oligosilsesquioxane as a coating layer on copper or lithium for achieving efficient and stable lithium plating-stripping cycles in a carbonate-based electrolyte. Operando analyses and theoretical simulation reveal the remarkable ability of the ionomer coating to enable electric field homogenization over a considerably large lithium-plating surface. The membrane coating, serving as an artificial solid-electrolyte interphase filter in minimizing parasitic reactions at the electrolyte-electrode interface, enables dendrite-free lithium plating on copper with outstanding coulombic efficiencies at room and elevated (50 °C) temperatures. The membrane coated copper demonstrates itself as a promising current collector for manufacturing high-quality pre-plated lithium thin-film anode.

25 ENERGY STORAGE↗
DOE OSTI2025

Interface morphogenesis with a deformable secondary phase in solid-state lithium batteries

Here, the complex morphological evolution of lithium metal at the solid-state electrolyte interface limits performance of solid-state batteries, leading to inhomogeneous reactions and contact loss. Inspired by biological morphogenesis, we developed an interfacial self-regulation concept in which a deformable secondary phase dynamically aggregates at the interface in response to local electro-chemo-mechanical stimuli, enhancing contact. The stripping of a lithium electrode that contains 5 to 20 mole % electrochemically inactive sodium domains causes spontaneous sodium accumulation across the interface, with the sodium deforming to attain intimate electrical contact without blocking lithium transport. This process, characterized with operando x-ray tomography and electron microscopy, mitigates voiding and improves cycling at low stack pressures. The counterintuitive strategy of adding electrochemically inactive alkali metal to improve performance demonstrates the utility of interfacial self-regulation for solid-state batteries.

Yoon, Sun Geun [Georgia Institute of Technology, A↗
DOE OSTI2025

Alloying Interlayers for Anode‐Less Lithium‐Metal Polymer Batteries

Anode‐less lithium‐metal batteries potentially offer further increased energy densities. However, the Coulombic efficiency (CE) of lithium plating and stripping, as a classical measure of Li inventory reversibility, is commonly still insufficient for achieving long‐lasting rechargeable batteries. Herein, the potential benefits of employing thin (20 nm) metal interlayers of Ag, Pt, and Au on Cu to alloy with Li in Cu||Li half‐cells and induce homogeneous Li plating with poly(ethylene oxide)‐based electrolytes are investigated. Interestingly, not all alloying interlayers enable a higher CE compared to neat Cu foil with 84%—specifically Ag@Cu with only 81%, while the best performing one, Au@Cu, provides a substantially increased CE of 91%. While generally the formation of “dead lithium” is found to be the major source of CE, this appears to be less pronounced in the case of Au@Cu, indeed. Further improvement can be achieved by carefully adjusting the cell voltage to a region in which the continuous de‐/alloying is suppressed, yielding a further enhanced CE of 94%, thus highlighting the need for a comprehensive approach to design suitable electrode chemistries and designs beyond a “simple” material improvement.

anode-less battery↗
DOE OSTI2021

Method of improved performance in metal electrodes for batteries

Disclosed are methods for pre-conditioning or pre-treating the surface of a metal (e.g., lithium) electrode such that the cycle life and efficiency of the electrode within an electrochemical cell are improved through the prevention of dendrite growth. The pretreatment process includes the use of an alternating current to modify the surface properties of the metal electrode, such that a more uniform flux of metal ions is transferred across the electrode-electrolyte Interface in subsequent electrodeposition and electrodissolution processes. As a result, an electrode treated with such a process exhibits improved performance and durability, including markedly lower overpotentials and largely improved metal (e.g., lithium) retention in strip plate tests as compared with untreated electrodes.

Dasgupta, Neil P.↗
DOE OSTI2023

Non‐Linear Kinetics of The Lithium Metal Anode on Li 6 PS 5 Cl at High Current Density: Dendrite Growth and the Role of Lithium Microstructure on Creep

Abstract Interfacial instability, viz., pore formation in the lithium metal anode (LMA) during discharge leading to high impedance, current focusing induced solid–electrolyte (SE) fracture during charging, and formation/behaviour of the solid–electrolyte interphase (SEI), at the anode, is one of the major hurdles in the development of solid‐state batteries (SSBs). Also, understanding cell polarization behaviour at high current density is critical to achieving the goal of fast‐charging battery and electric vehicle. Herein, via in situ electrochemical scanning electron microscopy (SEM) measurements, performed with freshly deposited lithium microelectrodes on transgranularly fractured fresh Li6PS5Cl (LPSCl), the LiǀLPSCl interface kinetics are investigated beyond the linear regime. Even at relatively small overvoltages of a few mV, the LiǀLPSCl interface shows non‐linear kinetics. The interface kinetics possibly involve multiple rate‐limiting processes, i.e., ion transport across the SEI and SE|SEI interfaces, as well as charge transfer across the LiǀSEI interface. The total polarization resistance R P of the microelectrode interface is determined to be ≈ 0.8 Ω cm 2 . It is further shown that the nanocrystalline lithium microstructure can lead to a stable LiǀSE interface via Coble creep along with uniform stripping. Also, spatially resolved lithium deposition, i.e., at grain surface flaws, grain boundaries, and flaw‐free surfaces, indicates exceptionally high mechanical endurance of flaw‐free surfaces toward cathodic load (>150 mA cm −2 ). This highlights the prominent role of surface defects in dendrite growth.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Transient Chemo‐Mechanical Model of Lithium Plating Impacted by External Pressure

Abstract Lithium anodes show great promise in commercial applications, but are hindered by lithium plating and dendrite growth which cause safety concerns during long‐term cell operation. Stack pressure is experimentally observed to improve cell lifetime; however, the relationship between stress and lithium deposition has remained difficult to elucidate. In this work, a transient, 3D, finite‐element model of the evolution of a lithium anode due to stripping and plating is developed. The evolution of a microscale protrusion on the anode surface is tracked over one charge‐discharge cycle with respect to stack pressure and lithium yield strength. Lithium plastic deformation, nonconformal anode‐separator contact, and separator porosity effects are accounted for. Over the course of several hours of stripping/plating, the anode surface evolves to a similar morphology under pressure regardless of the initial conditions due to lithium plastic deformation and hardening. The rate of this evolution highly depends on the applied pressure and assumed lithium yield strength.

25 ENERGY STORAGE↗
DOE OSTI2024

Study of Void Formation at the Lithium|Solid Electrolyte Interface

There is growing recognition of the critical role of void formation in lithium metal anodes in solid-state batteries and its impact on electrochemical performance. While experimental studies have demonstrated the challenges ensuing from void formation at the lithium metal interface with the solid electrolyte, there is a need to understand and quantify the role of intrinsic transport properties in lithium metal and the impact of external stimuli, such as temperature, pressure, and current density. Here, we develop this understanding by constructing a phase field-based model that captures the evolution of void domains at the lithium-solid electrolyte interface. Growth of the pores is driven by the fast removal of lithium from the interface during stripping at high current densities. Relative magnitudes of the bulk and surface lithium diffusivities, along with the applied current density, dictate the final pore morphology. Increasing the temperature results in faster diffusion, while external applied pressure causes creep flow of lithium, both of which help to mitigate the evolution of voids by quickly transporting metal from the bulk to the interface. Finally, a phase map as a function of temperature and pressure is developed as a guide to determine the regions that can lead to the stable cycling of lithium metal.

25 ENERGY STORAGE↗
DOE OSTI2022

Crossover Effects in Lithium–Metal Batteries with a Localized High Concentration Electrolyte and High–Nickel Cathodes

While crossover effects, such as transition–metal dissolution, are well–understood in lithium–ion batteries, there is a limited understanding of the effect of crossed–over chemical species in cells with oxide cathodes and lithium–metal anodes. In this work, the effects of cathode–to–anode and anode–to–cathode crossover are explored in cells with a high–nickel cathode, lithium–metal anode, and a localized high–concentration electrolyte (LHCE). Dramatic differences are found among cells; a lithium–metal anode paired with a high–nickel cathode has three times less solid–electrolyte interphase growth than a lithium–metal anode paired with lithium metal. Meanwhile, the cathode paired with lithium metal has 2–3 times higher capacity fade than the same cathode paired with graphite. Decomposition and crossover of the FSI salt is identified as the main source of these changes. The fluorine in the salt is first stripped off at the lithium–metal anode, and the remaining sulfur and nitrogen cross over to the cathode. Although the reduction in fluorine content harms the surface stability of the cathode, the lithium–metal anode benefits from the increased fluorine content. Furthermore, because the lithium–metal anode is typically the bottleneck for cells with thin lithium, crossover is a major factor in the enhanced performance of lithium–metal batteries with LHCE.

25 ENERGY STORAGE↗
DOE OSTI2020

A Cation-Tethered Flowable Polymeric Interface for Enabling Stable Deposition of Metallic Lithium

A fundamental challenge, shared across many energy storage devices, is the complexity of electrochemistry at the electrode–electrolyte interfaces that impacts the Coulombic efficiency, operational rate capability, and lifetime. Specifically, in energy-dense lithium metal batteries, the charging/discharging process results in structural heterogeneities of the metal anode, leading to battery failure by short-circuit and capacity fade. In this work, we take advantage of organic cations with lower reduction potential than lithium to build an electrically responsive polymer interface that not only adapts to morphological perturbations during electrodeposition and stripping but also modulates the lithium ion migration pathways to eliminate surface roughening. As a result, we find that this concept can enable prolonging the long-term cycling of a high-voltage lithium metal battery by at least twofold compared to bare lithium metal.

25 ENERGY STORAGE↗
DOE OSTI2022

Perspective—Lithium Metal Nucleation and Growth on Conductive Substrates: A Multi-Scale Understanding from Atomistic, Nano-, Meso-, to Micro-Scales

Reversible lithium (Li) deposition and stripping on conductive substrates like copper is vital for long-life high-energy rechargeable Li batteries. The reversibility is believed hindered by solid electrolyte interphase (SEI) formation and Li dendritic growth. Via in situ, operando cryo-microscopy and molecular dynamics simulation, we discovered amorphous Li before a disorder-order phase transition to bcc phase. The kinetics plays a significant role in Li nucleation and morphology evolution. This perspective on Li nucleation and growth from atomistic to nano- (<20 nm), meso- (20–100 nm), and micro-scales (>100 nm) provides a practical guidance on regulating dense Li deposits reversibly for long life performance.

25 ENERGY STORAGE↗
DOE OSTI2026

Nanoengineering of non-aqueous liquid electrolyte solutions for future lithium metal batteries

Research and development of non-aqueous electrolyte solutions are essential for practical advancement towards the production of high-energy lithium metal batteries (LMBs). An ideal LMB electrolyte solution should enable highly efficient, uniform and prolonged lithium metal plating and stripping, preserve the electrodes’ electro(chemo)mechanical properties and ensure compatibility with all cell components. However, despite extensive research efforts, scientists have yet to achieve an electrolyte design that meets these requirements simultaneously. Here, by examining the nanoengineering aspects of various non-aqueous electrolyte solution designs, we elucidate the understanding of the nanoscale physicochemical and electrochemical processes taking place in LMBs, which are mainly governed by the thermodynamic and kinetic properties of the electrolyte system. We also explore emerging research directions and propose an accelerated, iterative framework that integrates nanoengineering principles with machine learning, high-throughput computation and experimentation to facilitate the development of next-generation non-aqueous electrolyte solutions for practical LMBs.

Weintz, Dominik↗
DOE OSTI2020

Quantification of Inactive Lithium and Solid–Electrolyte Interphase Species on Graphite Electrodes after Fast Charging

Rapid charging of Li-ion batteries is limited by lithium plating on graphite anodes, whereby Li+ ions are reduced to Li metal on the graphite particle surface instead of inserting between graphitic layers, which directly contributes to cell capacity loss because of the low reversibility of the Li plating/stripping process. Furthermore, precisely identifying the onset and amount of Li plating is therefore vital in order to remedy these issues. We demonstrate a titration technique with a detection limit of 20 nmol (5 × 10 –4 mAh) of Li that can be used to quantify inactive Li that remains on the graphite electrode after fast charging. The titration is extended to quantify the total amount of solid carbonate species and lithium acetylide (Li 2 C 2 ) within the solid–electrolyte interphase (SEI), and electrochemical modeling is used to determine the Li plating exchange current density (10 A/m 2 ) and stripping efficiency (65%) of plated Li metal on graphite. These techniques provide a highly accurate measure of the onset of Li plating and quantitative insight into graphite SEI evolution during fast charging.

25 ENERGY STORAGE↗
DOE OSTI2022

Quantification of Dead Lithium on Graphite Anode under Fast Charging Conditions

A series of computational and experimental studies were conducted to understand the onset of lithium plating and subsequent quantification of dead lithium on graphite electrodes in the design of fast charging batteries. The experiments include titration and relaxation studies for detecting initiation of lithium metal plating for various SOC and C-rates, which are compared against the thermodynamically consistent phase field computational results. The collaborative study on "model graphite electrode" with 2.18 mAh cm-2 nominal capacity at 25 degrees C demonstrates: (1) the macroscopic voltage response during relaxation studies indicate the reintercalation of plated lithium into the graphite anode; (2) for SOC below 60% and low C-Rates, there is no dead lithium; (3) for SOC between 60% to 80%, and C-Rates in the range of 4C-6C show dead lithium both in experiments and simulations; (4) at 100% SOC and 4C-6C rates, large amounts of dead lithium are observed. The study presented here allows us to evaluate the effects of the physical properties of the electrochemical system on plating and stripping kinetics and the amount of dead lithium on graphite electrodes, which determines the cell capacity loss under fast charge.

batteries↗
DOE OSTI2023

Recovery of critical elements from end-of-life lithium ion batteries with supported membrane solvent extraction

Single-stage and multi-stage systems and methods for the recovery of critical elements in substantially pure form from lithium ion batteries are provided. The systems and methods include supported membrane solvent extraction using an immobilized organic phase within the pores of permeable hollow fibers. The permeable hollow fibers are contacted by a feed solution on one side, and a strip solution on another side, to provide the simultaneous extraction and stripping of elements from dissolved lithium ion cathode materials, while rejecting other elements from the feed solution. The single- and multi-stage systems and methods can selectively recover cobalt, manganese, nickel, lithium, aluminum and other elements from spent battery cathodes and are not limited by equilibrium constraints as compared to traditional solvent extraction processes.

Bhave, Ramesh R.↗
DOE OSTI2020

Performance degradation due to anodic failure mechanisms in lithium-ion batteries

Here, we report a mechano-chemical model for anodic degradation during fast-charging of nickel-manganese-cobalt (NMC)/graphite (C) cell due to SEI growth, lithium plating/stripping, dead lithium storage, and film fracture of composite SEI and plated lithium film. Degradation of the battery is analyzed for a range of charging rates from 1 to 6 C-rates, and the influence of plating mechanisms – lithium plating and dead lithium deposition and recovery during stripping – on the film resistance of the anode are accounted for in the model. Dynamic evolution of the interfacial properties is modeled using rule-of-mixture approach. Model predictions of plating associated stress fields are used to compute critical energy release rate for film cracking. The results indicate an increased tendency of fracture for thinner SEI film with lithium plating at higher charging rates. The process of reforming the cracked film absorbs a significant portion of the electrode current thereby reducing the cell capacity and plating efficiency. The mechano-chemical model provides an extensive analytical framework for understanding the synergistic coupling of anodic degradation mechanisms, prognosticating conditions of SEI failure, and evaluating the capacity fade and efficiency of lithium-ion battery.

25 ENERGY STORAGE↗