Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “linear switching”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Femtojoule optical nonlinearity for deep learning with incoherent illumination

Optical neural networks (ONNs) are a promising computational alternative for deep learning due to their inherent massive parallelism for linear operations. However, the development of energy-efficient and highly parallel optical nonlinearities, a critical component in ONNs, remains an outstanding challenge. Here, we introduce a nonlinear optical microdevice array (NOMA) compatible with incoherent illumination by integrating the liquid crystal cell with silicon photodiodes at the single-pixel level. We fabricate NOMA with more than half a million pixels, each functioning as an optical analog of the rectified linear unit at ultralow switching energy down to 100 femtojoules per pixel. With NOMA, we demonstrate an optical multilayer neural network. Our work holds promise for large-scale and low-power deep ONNs, computer vision, and real-time optical image processing.

36 MATERIALS SCIENCE↗
NASA NTRS1979

Fader and ramp shaper replace linear filters

Digital "fader" or "ramp shaper" circuits replace linear filters in suppressing switching transients and instabilities within servocontrol systems. Circuits can be optimized to introduce no attenuation, transport delay, or phase lags in new output signal.

Robinson, T. A.↗
NASA NTRS1992

Superconductivity devices: Commercial use of space

The high T(sub c) superconducting ceramic materials, developed in 1987, are now being extensively investigated for a variety of engineering applications. These applications include such devices as conducting links, rotating and linear bearings, sensors, filters, switches, high Q cavities, magnets, and motors. Some of these devices take advantage of the material's ability to lose all electrical resistance at a critical temperature, T(sub c), while others make use of the repulsion forces generated between the magnetic field of a permanent magnet and a superconductor which is cooled below its T(sub c), Meissner effect. This report describes the work accomplished to date by: (1) reviewing the present state of the art in actuator technology, (2) evaluating processing and fabrication of high strain electrostrictive materials, and (3) testing these electrostrictive materials.

Haertling, Gene↗
NASA NTRS2005

Printed Antennas Made Reconfigurable by Use of MEMS Switches

A class of reconfigurable microwave antennas now undergoing development comprise fairly conventional printed-circuit feed elements and radiating patches integrated with novel switches containing actuators of the microelectromechanical systems (MEMS) type. In comparison with solid-state electronic control devices incorporated into some prior printed microwave antennas, the MEMS-based switches in these antennas impose lower insertion losses and consume less power. Because the radio-frequency responses of the MEMS switches are more nearly linear, they introduce less signal distortion. In addition, construction and operation are simplified because only a single DC bias line is needed to control each MEMS actuator.

Simons, Rainee N.↗
DOE OSTI2026

Electrical Switching and Imaging of Antiferromagnetic Spins in Perovskite Epitaxial Thin Films

Electrical control of antiferromagnets is essential for the field of antiferromagnetic spintronics that promises ultrafast speed and terahertz dynamics. However, the large family of complex oxide antiferromagnets such as perovskites have been largely unexplored. Here, we demonstrate electrical switching and detection of Néel vector in LaFeO 3 epitaxial thin films with an epitaxy-enabled biaxial anisotropy, of which the switching behavior is understood by comparing to magnetic field controlled spin Hall magnetoresistance measurements. The electrical switching is corroborated by imaging of antiferromagnetic domains using X-ray Magnetic Linear Dichroism Photoemission Electron Microscopy. Electrical switching of 3-nm and 10-nm LaFeO 3 films was achieved over a wide temperature range of 25 to 300 K. This work offers an attractive platform for exploration of antiferromagnetic spintronics and other emerging phenomena such as potential insulating altermagnetism.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Thickness scaling and ferroelectric switching in wurtzite structure zinc magnesium oxide thin films

This study reports the thickness scaling of sputtered ferroelectric Zn 0.61 Mg 0.39 O (ZMO) thin films down to 43 nm. Encapsulated IrO 2 /ZMO/Ir capacitors exhibited switchable polarizations exceeding 50 μC cm −2 and coercive fields that increased from 3.9 to 4.4 MV cm −1 as the thickness decreased. Switching kinetics are best described by the simultaneous non-linear nucleation and the growth model. Bimodal switching is prevalent at low thicknesses, with the fastest switching times measured to be approximately 400 ns. Device encapsulation made ZMO switching kinetics more abrupt, potentially due to changes in the concentration of atmosphere-induced defects such as hydroxides. These results demonstrate stable ferroelectricity and sub-microsecond switching in sub-50 nm wurtzite ZMO, highlighting its potential as a low-voltage ferroelectric for integrated nonvolatile memory applications.

36 MATERIALS SCIENCE↗
NASA NTRS2005

Modeling and Inverse Controller Design for an Unmanned Aerial Vehicle Based on the Self-Organizing Map

The next generation of aircraft will have dynamics that vary considerably over the operating regime. A single controller will have difficulty to meet the design specifications. In this paper, a SOM-based local linear modeling scheme of an unmanned aerial vehicle (UAV) is developed to design a set of inverse controllers. The SOM selects the operating regime depending only on the embedded output space information and avoids normalization of the input data. Each local linear model is associated with a linear controller, which is easy to design. Switching of the controllers is done synchronously with the active local linear model that tracks the different operating conditions. The proposed multiple modeling and control strategy has been successfully tested in a simulator that models the LoFLYTE UAV.

Cho, Jeongho↗
DOE OSTI2025

Distribution System Blackstart and Restoration Using DERs and Dynamically Formed Microgrids

Extreme weather events have led to long-duration outages in the distribution system (DS), necessitating novel approaches to blackstart and restore the system. Existing blackstart solutions utilize blackstart units to establish multiple microgrids (MGs), sequentially energize non-blackstart units, and restore loads. However, these approaches often result in isolated MGs. In DERs-aided blackstart, the continuous operation of these MGs is limited by the finite energy capacity of commonly used blackstart units like battery energy storage (BES)-based gridforming inverters (GFMIs). To address this issue, this article proposes a holistic blackstart and restoration framework that incorporates synchronization between dynamic MGs and the entire DS with the transmission grid (TG). To support synchronization, we leveraged virtual synchronous generator-based control for GFMIs to estimate their frequency response to load pick-up events using only initial/final quasi-steady-state points. Subsequently, a synchronization switching condition is developed to model synchronizing switches, aligning them seamlessly with a linearized branch flow problem. Finally, we designed a bottomup blackstart and restoration framework that considers the switching structure of the DS, energizing/synchronizing switches, DERs with grid-following inverters, and BES-based GFMIs with frequency security constraints. In conclusion, the proposed framework is validated in IEEE-123-bus system, considering cases with two and four GFMIs under various TG recovery instants.

24 POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRS2002

Low-Loss, High-Isolation Microwave Microelectromechanical Systems (MEMS) Switches Being Developed

Switches, electrical components that either permit or prevent the flow of electricity, are the most important and widely used electrical devices in integrated circuits. In microwave systems, switches are required for switching between the transmitter and receiver; in communication systems, they are needed for phase shifters in phased-array antennas, for radar and communication systems, and for the new class of digital or software definable radios. Ideally, switches would be lossless devices that did not depend on the electrical signal's frequency or power, and they would not consume electrical power to change from OFF to ON or to maintain one of these two states. Reality is quite different, especially at microwave frequencies. Typical switches in microwave integrated circuits are pin diodes or gallium arsenide (GaAs) field-effect transistors that are nonlinear, with characteristics that depend on the power of the signal. In addition, they are frequency-dependent, lossy, and require electrical power to maintain a certain state. A new type of component has been developed that overcomes most of these technical difficulties. Microelectromechanical (MEMS) switches rely on mechanical movement as a response to an applied electrical force to either transmit or reflect electrical signal power. The NASA Glenn Research Center has been actively developing MEMS for microwave applications for over the last 5 years. Complete fabrication procedures have been developed so that the moving parts of the switch can be released with near 100-percent yield. Moreover, the switches fabricated at Glenn have demonstrated state-of-the-art performance. A typical MEMS switch is shown. The switch extends over the signal and ground lines of a finite ground coplanar waveguide, a commonly used microwave transmission line. In the state shown, the switch is in the UP state and all the microwave power traveling along the transmission line proceeds unimpeded. When a potential difference is applied between the cantilever and the transmission line, the cantilever is pulled downward until it connects the signal line to the ground planes, creating a short circuit. In this state, all the microwave power is reflected. The graph shows the measured performance of the switch, which has less than 0.1 dB of insertion loss and greater than 30dB of isolation. These switches consume negligible electrical power and are extremely linear. Additional research is required to address reliability and to increase the switching speed.

Ponchak, George E.↗
NASA NTRS2013

Quasi-Linear Circuit

This work involved developing spacequalifiable switch mode DC/DC power supplies that improve performance with fewer components, and result in elimination of digital components and reduction in magnetics. This design is for missions where systems may be operating under extreme conditions, especially at elevated temperature levels from 200 to 300 degC. Prior art for radiation-tolerant DC/DC converters has been accomplished utilizing classical magnetic-based switch mode converter topologies; however, this requires specific shielding and component de-rating to meet the high-reliability specifications. It requires complex measurement and feedback components, and will not enable automatic re-optimization for larger changes in voltage supply or electrical loading condition. The innovation is a switch mode DC/DC power supply that eliminates the need for processors and most magnetics. It can provide a well-regulated voltage supply with a gain of 1:100 step-up to 8:1 step down, tolerating an up to 30% fluctuation of the voltage supply parameters. The circuit incorporates a ceramic core transformer in a manner that enables it to provide a well-regulated voltage output without use of any processor components or magnetic transformers. The circuit adjusts its internal parameters to re-optimize its performance for changes in supply voltage, environmental conditions, or electrical loading at the output

Bradley, William↗
NASA NTRS2008

A Novel Nanoionics-Based Switch for Microwave Applications

This paper reports the development and characterization of a novel switching device for use in microwave systems. The device utilizes a switching mechanism based on nanoionics, in which mobile ions within a solid electrolyte undergo an electrochemical process to form and remove a conductive metallic "bridge" to define the change of state. The nanoionics-based switch has demonstrated an insertion loss of approx.0.5dB, isolation of >30dB, low voltage operation (1V), low power (approx. micro-W) and low energy (approx. nJ) consumption, and excellent linearity up to 6 GHz. The switch requires fewer bias operations (due to non-volatile nature) and has a simple planar geometry allowing for novel device structures and easy integration into microwave power distribution circuits.

Nessel, James A.↗
DOE OSTI2021

Intrinsic synaptic plasticity of ferroelectric field effect transistors for online learning

Nanoelectronic devices emulating neuro-synaptic functionalities through their intrinsic physics at low operating energies is imperative toward the realization of brain-like neuromorphic computers. In this work, we leverage the non-linear voltage dependent partial polarization switching of a ferroelectric field effect transistor to mimic plasticity characteristics of biological synapses. Here, we provide experimental measurements of the synaptic characteristics for a 28nm high-k metal gate technology based device and develop an experimentally calibrated device model for large-scale system performance prediction. Decoupled read-write paths, ultra-low programming energies and the possibility of arranging such devices in a cross-point architecture demonstrate the synaptic efficacy of the device. Our hardware-algorithm co-design analysis reveals that the intrinsic plasticity of the ferroelectric devices has potential to enable unsupervised local learning in edge devices with limited training data

42 ENGINEERING↗
DOE OSTI2022

An Integrated Theoretical and Experimental Approach to Achieve Highly Polarizable Relaxor Ferroelectric Liquid Crystalline Polymers

In this project, we have designed and synthesized a series of aliphatic sulfonlyated chiral and achiral polyether. The major objective is to achieve ferroelectric liquid crystalline polymers with a high spontaneous polarization (0.04-0.08 C/m2). Due to the strong dipole-dipole interaction among the sulfonyl side groups, which resembles that among water molecules, these polyethers can exhibit various liquid crystalline self-assemblies without any rigid mesogens. By tuning the position of the sulfonyl groups, single versus double sulfonyl groups, and spacer/tail length and methyl branches, the liquid crystalline phases include smectic A, smectic C, and hexagonal columnar phases. When the single sulfonyl group is next to the main chain or disulfonyl groups are separated by a short C3 spacer, the dipolar interaction is too strong to allow any dipole switching. As a result, the linear dielectric behavior is observed with a low dielectric constant of 5-7. When the single sulfonyl groups are away from the main chain, the paraelectric behavior is obtained with a high dielectric constant around 20. From this study, we predict that by further tailoring the intermolecular interactions among the disulfonyl side groups, it is possible to achieve ferroelectric property for these liquid crystalline polymers. If successful, these ferroelectric liquid crystalline polymers can be used for efficient electrocaloric cooling applications.

36 MATERIALS SCIENCE↗
NASA NTRS1970

Precision full-wave rectifier

Simplified circuit uses one operational amplifier and two precision resistors. The amplifier is operated open loop for switching and closed loop for linear gain, both simultaneously.

Deboo, G. J.↗
NASA NTRS1976

Irradiate-anneal screening of total dose effects in semiconductor devices

An extensive investigation of irradiate-anneal (IRAN) screening against total dose radiation effects was carried out as part of a program to harden the Mariner Jupiter/Saturn 1977 (MJS'77) spacecraft to survive the Jupiter radiation belts. The method consists of irradiating semiconductor devices with Cobalt-60 to a suitable total dose under representative bias conditions and of separating the parts in the undesired tail of the distribution from the bulk of the parts by means of a predetermined acceptance limit. The acceptable devices are then restored close to their preirradiation condition by annealing them at an elevated temperature. IRAN was used when lot screen methods were impracticable due to lack of time, and when members of a lot showed a diversity of radiation response. The feasibility of the technique was determined by testing of a number of types of linear bipolar integrated circuits, analog switches, n-channel JFETS and bipolar transistors. Based on the results of these experiments a number of device types were selected for IRAN of flight parts in the MJS'77 spacecraft systems. The part types, screening doses, acceptance criteria, number of parts tested and rejected as well as the program steps are detailed.

Stanley, A. G.↗
NASA NTRS2001

The Electromagnetic Compatibility (EMC) Design Challenge for Scientific Spacecraft Powered by a Stirling Power Converter

A 55 We free-piston Stirling Technology Demonstration Convertor (TDC) has been tested as part of an evaluation to determine its feasibility as a means for significantly reducing the amount of radioactive material required compared to Radioisotope Thermoelectric Generators (RTGs) to support long-term space science missions. Measurements were made to quantify the low frequency magnetic and electric fields radiated from the Stirling's 80 Hertz (Hz) linear alternator and control electronics in order to determine the magnitude of reduction that will be required to protect sensitive field sensors aboard some science missions. One identified "Solar Probe" mission requires a 100 dB reduction in the low frequency magnetic field over typical military standard design limits, to protect its plasma wave sensor. This paper discusses the electromagnetic interference (EMI) control options relative to the physical design impacts for this power system, composed of 3 basic electrical elements. They are (1) the Stirling Power Convertor with its linear alternator, (2) the power switching and control electronics to convert the 90 V, 80 Hz alternator output to DC for the use of the spacecraft, and (3) the interconnecting wiring including any instrumentation to monitor and control items 1 and 2.

Sargent, Noel B.↗