Application of new materials
Lightweight materials for aircraft electrical system components
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Lightweight materials for aircraft electrical system components
Lightweight materials are an important component of the design of aerospace structures. Carbon nanotube materials have been considered for this purpose due to the strength and stiffness of individual nanotubes, and the commercial availability of bulk formats such as fibers. These fibers can have a ribbon cross section which results in a different design space for their composites relative to traditional reinforcements which have a round cross section. This work applies brick-and-mortar micromechanical models and classical lamination theory with an inverse approach to investigate the design space of these composites. Using this approach, the influences of fiber geometry and axial and transverse mechanical properties are mapped. Finally, a sensitivity study is performed and the relative impacts of ±10% variations in the constituent material and geometric properties are ranked. Lamina axial moduli were found to range from a maximum of 3x to 1x minimum relative to a target quasi-isotropic laminate modulus depending on the anisotropy and shear modulus of the lamina. The fiber targets depended strongly on the fiber volume fraction in the lamina and the fiber axial modulus target was found to range from 4.8x to 3.2x the quasi-isotropic laminate target. The sensitivity analysis found that the largest driver of performance was the volume fraction, followed by the fiber axial modulus. While bio-based brick-and-mortar composites, such as nacre, can benefit from reinforcement aspect ratios above 10, for carbon nanotube ribbon (or carbon fiber)/polymer composites the sensitivity study indicated that the optimal cross-sectional aspect ratio was relatively smaller, potentially less than three.
The development of lightweight structural materials is crucial for enhancing the performance and deployment feasibility of fission batteries. This study aims to produce lightweight structural materials whose strength-to-weight ratios exceed those of current widely used structural materials. To achieve this, advanced modeling and simulation tools were employed to design lattice structures with different lattice parameters and different lattice types. A process was successfully developed for transforming lattice-structured models into Multiphysics Object Oriented Simulation Environment (MOOSE) inputs. Finite element modeling (FEM) was used to simulate the uniaxial tensile testing of the lattice-structured parts to investigate the stress distribution at a given displacement. The modeling results showed that the lattice-structured sample displayed a lower Young’s modulus in comparison to the solid material; the increase in solid shell thickness and blend radius enhances the mechanical performance; and the effect of unit cell size on macro scale stress is minimal. Tensile testing was conducted on the solid and lattice-structured materials fabricated by laser powder bed fusion (LPBF) additive manufacturing. The experimental results agreed well with the model prediction. The approach of using modeling as a guiding tool for preliminary material design can significantly save time and cost for new material development.
Aerogels are attractive materials for a variety of NASA missions because they are ultralightweight, have low thermal conductivity and low-dielectric constants, and can be readily doped with other materials. Potential NASA applications for these materials include lightweight insulation for spacecraft, habitats, and extravehicular activity (EVA) suits; catalyst supports for fuel cell and in situ resource utilization; and sensors for air- and water-quality monitoring for vehicles, habitats, and EVA suits. Conventional aerogels are extremely fragile and require processing via supercritical fluid extraction, which adds cost to the production of an aerogel and limits the sizes and geometries of samples that can be produced from these materials. These issues have severely hampered the application of aerogels in NASA missions.
The Center for Lightweighting Materials and Processing (CLAMP) was established in September 1998 with a grant from the Department of Energy’s Graduate Automotive Technology Education (GATE) program. The center received the second round of GATE grant in 2005 under the title “Upgrading the Center for Lightweighting Automotive Materials and Processing”. Using the two grants, the Center has successfully created 10 graduate level courses on lightweight automotive materials, integrated them into master’s and PhD programs in Automotive Systems Engineering, and offered them regularly to the graduate students in the program. In addition, the Center has created a web-based lightweight automotive materials database, conducted research on lightweight automotive materials and organized seminars/symposia on lightweight automotive materials for both academia and industry. The faculty involved with the Center has conducted research on a variety of topics related to design, testing, characterization and processing of lightweight materials for automotive applications and have received numerous research grants from automotive companies and government agencies to support their research. The materials considered included advanced steels, light alloys (aluminum, magnesium and titanium) and fiber reinforced polymer composites. In some of these research projects, CLAMP faculty have collaborated with industry partners and students have used the research facilities at industry locations. The specific objectives of the project during the current funding period (2005 – 2012) were as follows: (1) develop new graduate courses and incorporate them in the automotive systems engineering curriculum (2) improve and update two existing courses on automotive materials and processing (3) upgrade the laboratory facilities used by graduate students to conduct research (4) expand the Lightweight Automotive Materials Database to include additional materials, design case studies and make it more accessible to outside users (5) provide support to graduate students for conducting research on lightweight automotive materials and structures (6) provide industry/university interaction through a graduate certificate program on automotive materials and technology idea exchange through focused seminars and symposia on automotive materials.
Lightweight and tough engineered materials are often designed with three-dimensional hierarchy and interconnected structural members whose junctions are detrimental to their performance because they serve as stress concentrations for damage accumulation and lower mechanical resilience. We introduce a previously unexplored class of architected materials, whose components are interwoven and contain no junctions, and incorporate micro-knots as building blocks within these hierarchical networks. Tensile experiments, which show close quantitative agreements with an analytical model for overhand knots, reveal that knot topology allows a new regime of deformation capable of shape retention, leading to a ~92% increase in absorbed energy and an up to ~107% increase in failure strain compared to woven structures, along with an up to ~11% increase in specific energy density compared to topologically similar monolithic lattices. Our exploration unlocks knotting and frictional contact to create highly extensible low-density materials with tunable shape reconfiguration and energy absorption capabilities.
The main objective of this project is to develop, analyze and validate data, methodologies and tools that support widespread applications of automotive lightweighting technologies. Two underlying principles are guiding the research efforts towards this objective: • Seamless integration between the lightweight materials selected for certain vehicle systems, cost-effective methods for their design and manufacturing, and practical means to enhance their durability while reducing their Life-Cycle-Costs (LCC). • Smooth migration of the experience and findings accumulated so far at WVU in the areas of designing with lightweight materials, innovative joining concepts and durability predictions, from applications to the area of weight savings for heavy vehicle systems and hydrogen storage tanks, to lightweighting applications of selected systems or assemblies in light–duty vehicles.
Here this paper presents an overview on the application of CALPHAD (CALculation of Phase Diagrams) methodology in the design and development of advanced lightweight metallic materials including magnesium, aluminum, titanium, aluminum-based metal matrix composites, and high entropy alloys. In this work, CALPHAD methodology has been established and summarized from the construction of databases describing thermodynamics, atomic mobility, kinetics, thermo-physical properties (such as viscosity) to the application of computational design of lightweight materials. The examples in this paper have demonstrated the effectiveness and capability of CALPHAD methodology in accelerating the design of advanced lightweight materials by optimizing the compositions and various heat-treatment conditions, modifying the evolution of microstructures during processing, and finally predicting the mechanical properties (e.g., yield strength and hardness) of the lightweight components. Although the examples are given in lightweight alloys for structural applications, the fundamental methodology and modeling principles are applicable to all materials and engineering applications. Thus, the future of the advanced material design will be strongly based on development of CALPHAD methodology such as the construction of reliable databases coupled with CALPHAD-based models for various applications.
Inexpensive lightweight neutron shield material has high strength and ductility and withstands high internal heat generation rates without excessive thermal stress. This composite material combines structural and thermal properties of aluminum, neutron moderating properties of titanium hydride, and neutron absorbing characteristics of boron carbide.
Fission batteries require lightweight structural materials that demonstrate structural resilience when subjected to repeated shutdown, transportation, startup cycles, and certain external conditions, including rare events such as seismic vibrations and tsunamis. The objectives of this project are (1) to produce lightweight structural materials whose strength-to-weight ratios and fatigue resistance exceed those of current widely used structural materials such as 316 stainless steels (SS316), and (2) to enhance radiation tolerance of structural materials over a suitable service temperature range. To achieve these, (1) a lattice structure will be produced, (2) advanced modeling and simulation tools will be employed to design lattice structures (e.g., a gyroid structure) that reduce stress concentrations and thus increase fatigue resistance, and (3) one-dimensional (1-D) carbon nanotubes will be added to enhance radiation resistance. To validate our solution, high-temperature tensile and fatigue testing, in combination with microstructure characterization, will be conducted on wrought materials, additively manufactured solid materials, and the designed lightweight lattice structure material. Ion irradiation, microstructure characterization, and nanoindentation will be carried out to investigate the effect of 1-D carbon nanotubes on radiation tolerance. Successful completion of this project will deliver a material to serve as a substitute for current SS316 using the same chemistry but with lighter weight and improved mechanical properties. In addition, a material with carbon nanotubes can be designed for improved radiation tolerance over a suitable service temperature range. This project will establish new techniques in innovative materials/lattice design, advanced macroscale properties prediction, and the application of state-of-the-art processes.
A new class of strong, lightweight, porous materials has been invented as an outgrowth of an effort to develop reinforced silica aerogels. The new material, called X-Aerogel is less hygroscopic, but no less porous and of similar density to the corresponding unmodified aerogels. However, the property that sets X-Aerogels apart is their mechanical strength, which can be as much as two and a half orders of magnitude stronger that the unmodified aerogels. X-Aerogels are envisioned to be useful for making extremely lightweight, thermally insulating, structural components, but they may also have applications as electrical insulators, components of laminates, catalyst supports, templates for electrode materials, fuel-cell components, and filter membranes.
The notion of a “fission battery” conveys a vision focused on realizing very simple “plug-and-play” nuclear systems that can be integrated into a variety of applications requiring affordable, reliable energy in the form of electricity and/or heat and function without operations and maintenance staff. Fission batteries require lightweight structural materials to increase their mobility, and the lightweight materials must demonstrate structural resilience under various conditions. The objective of this work is to develop lightweight structural material featuring a good combination of mechanical properties using advanced modeling and simulation together with an advanced additive manufacturing technique such as laser powder bed fusion. The preliminary results show that different lattice structures and types can be successfully meshed using nTopology software, and the lattice structure data can be successfully transformed to Multiphysics Object-Oriented Simulation Environment (MOOSE) input. Finite Element Analysis (FEA) displays that, at macro/engineering scale simulation, the weight saving design has an obvious effect on tensile behavior such as effective elastic modulus and yield stress. The novel approaches of this work are (1) development of optimized lattice structures for improved mechanical properties using advanced simulation and modeling techniques; and (2) model predictions of the mechanical properties (e.g., strength and stress distribution) of macroscopic materials in order to preliminarily select a lattice structure for additive manufacturing.
The notion of a “fission battery” conveys a vision focused on realizing very simple “plug-and-play” nuclear systems that can be integrated into a variety of applications requiring affordable, reliable energy in the form of electricity and/or heat and function without operations and maintenance staff. Fission batteries require lightweight structural materials to increase their mobility, and the lightweight materials must demonstrate structural resilience under various conditions. The objective of this work is to develop lattice structured lightweight structural material featuring a good combination of mechanical properties using advanced modeling and simulation together with an advanced additive manufacturing technique such as laser powder bed fusion. The preliminary results show that different lattice structures and types can be successfully meshed using nTopology software, and the lattice structure data can be successfully transformed to Multiphysics Object-Oriented Simulation (MOOSE) Environment input. Finite Element Analysis (FEA) displays that, at macro/engineering scale simulation, the weight saving design has an obvious effect on tensile behavior such as effective elastic modulus and yield stress. The novel approaches of this work are (1) development of lattice structures for improved mechanical properties using advanced simulation and modeling techniques; and (2) model predictions of the mechanical properties (e.g., strength and stress distribution) of macroscopic materials in order to preliminarily select a lattice structure for additive manufacturing.
The notion of a “fission battery” conveys a vision focused on realizing very simple “plug-and-play” nuclear systems that can be integrated into a variety of applications requiring affordable, reliable energy in the form of electricity and/or heat and function without operations and maintenance staff. Fission batteries require lightweight structural materials to increase their mobility, and the lightweight materials must demonstrate structural resilience under various conditions. The objective of this work is to develop lattice structured lightweight structural material featuring a good combination of mechanical properties using advanced modeling and simulation together with an advanced additive manufacturing technique such as laser powder bed fusion. The preliminary results show that different lattice structures and types can be successfully meshed using nTopology software, and the lattice structure data can be successfully transformed to Multiphysics Object-Oriented Simulation (MOOSE) Environment input. Finite Element Analysis (FEA) displays that, at macro/engineering scale simulation, the weight saving design has an obvious effect on tensile behavior such as effective elastic modulus and yield stress. The novel approaches of this work are (1) development of lattice structures for improved mechanical properties using advanced simulation and modeling techniques; and (2) model predictions of the mechanical properties (e.g., strength and stress distribution) of macroscopic materials in order to preliminarily select a lattice structure for additive manufacturing.
In this article, we estimate the potential energy benefits of lightweighting the light-duty vehicle fleet from both vehicle manufacturing and use perspectives using plausible lightweight vehicle designs involving several alternative lightweight materials, low- and high-end estimates of vehicle manufacturing energy, conventional and alternative powertrains, and two different market penetration scenarios for alternative powertrain light-duty vehicles at the fleet level. Cumulative life cycle energy savings (through 2050) across the nine material scenarios based on the conventional powertrain in the U.S. vehicle fleet range from -29 to 94 billion GJ, with the greatest savings achieved by multi-material vehicles that select different lightweight materials to meet specific design purposes. Lightweighting alternative-powertrain vehicles could produce significant energy savings in the U.S. vehicle fleet, although their improved powertrain efficiencies lessen the energy savings opportunities for lightweighting. A maximum level of cumulative energy savings of lightweighting the U.S. light-duty vehicle through 2050 is estimated to be 66.1billion GJ under the conventional-vehicle dominated business-as-usual penetration scenario.
An apparatus is described for producing a lightweight structural material (12), by forming gas-filled shells (38) of molten material from a matrix of nozzles (22) that form shells of very uniform size at very uniform rates. The matrix of molten shells coalesce into a multi-cell material of controlled cellular structure. The shells can be of two different sizes (38, 44) that are interspersed, to form a multicell material that has a regular cell pattern but which avoids planes of weakness and localized voids. The gas (50) in the shells can be under a high pressure, and can be a fire extinguishing gas.
The United States Automotive Materials Partnership LLC (USAMP) was formed in 1993 as a partnership between Chrysler Corporation, Ford Motor Company, and General Motors Corporation. Since then the U.S. Department of Energy (DOE) has supported its activities with funding and technical support. The mission of the USAMP is to conduct vehicle-oriented research and development in materials and materials processing to improve the competitiveness of the U.S. Auto Industry. Its specific goals are: (1) To conduct joint research to further the development of lightweight materials for improved automotive fuel economy; and (2) To work with the Federal government to explore opportunities for cooperative programs with the national laboratories, Federal agencies such as the DOE and universities. As a major component of the DOE's Office of FreedomCAR and Vehicle Technologies Program (FCVT) collaboration with the USAMP, the Automotive Lightweighting Materials (ALM) program focuses on the development and validation of advanced materials and manufacturing technologies to significantly reduce automotive vehicle body and chassis weight without compromising other attributes such as safety, performance, recyclability, and cost. The FCVT was announced in FY 2002 and implemented in FY 2003, as a successor of the Partnership for a New Generation of Vehicles (PNGV), largely addressed under the first Cooperative Agreement. This second USAMP Cooperative Agreement with the DOE has expanded a unique and valuable framework for collaboratively directing industry and government research efforts toward the development of technologies capable of solving important societal problems related to automobile transportation. USAMP efforts are conducted by the domestic automobile manufacturers, in collaboration with materials and manufacturing suppliers, national laboratories, universities, and other technology or trade organizations. These interactions provide a direct route for implementing newly developed materials and technologies, and have resulted in significant technical successes to date, as discussed in the individual project summary final reports. Over 70 materials-focused projects have been established by USAMP, in collaboration with participating suppliers, academic/non-profit organizations and national laboratories, and executed through its original three divisions: the Automotive Composites Consortium (ACC), the Automotive Metals Division (AMD), and Auto/Steel Partnership (A/SP). Two new divisions were formed by USAMP in 2006 to drive research emphasis on integration of structures incorporating dissimilar lightweighting materials, and on enabling technology for nondestructive evaluation of structures and joints. These new USAMP divisions are: Multi-Material Vehicle Research and Development Initiative (MMV), and the Non-Destructive Evaluation Steering Committee (NDE). In cooperation with USAMP and the FreedomCAR Materials Technical Team, a consensus process has been established to facilitate the development of projects to help move leveraged research to targeted development projects that eventually migrate to the original equipment manufacturers (OEMs) as application engineering projects. Research projects are assigned to one of three phases: concept feasibility, technical feasibility, and demonstration feasibility. Projects are guided through ongoing monitoring and USAMP offsite reviews, so as to meet the requirements of each phase before they are allowed to move on to the next phase. As progress is made on these projects, the benefits of lightweight construction and enabling technologies will be transferred to the supply base and implemented in production vehicles. The single greatest barrier to automotive use of lightweight materials is their high cost; therefore, priority is given to activities aimed at reducing costs through development of new materials, forming technologies, and manufacturing processes. The emphasis of the research projects reported in this document was largely on applied research and evaluation of mass savings opportunities through the aggressive application of lightweight materials, advanced computational methods, and the demonstration of production capable manufacturing processes intended for high-volume applications, all directed towards the FreedomCAR Program goals. Priority lightweighting materials include advanced high-strength steels (AHSS), aluminum, magnesium, titanium, and composites such as metal-matrix materials, and glass- and carbon-fiber-reinforced thermosets and thermoplastics. Besides developing valuable new design and material property information, several projects have extensively used computer-based product modeling and simulation technologies to optimize designs and materials usage while addressing the cost-performance issues. The purpose of this Summary Final Closeout Report is to document the successes, degree of progress, technology dissemination efforts, and lessons learned.
The National Center for Manufacturing Sciences (NCMS) worked with the U.S. Department of Energy (DOE), National Energy Technology Laboratory (NETL), to bring together research and development (R&D) collaborations to develop and accelerate the knowledgebase and infrastructure for lightweighting materials and manufacturing processes for their use in structural and applications in the automotive sector.