Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “laser direct drive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Transport of lunar material to the sites of the colonies

An 'existence proof' is attempted for the feasibility of transport of lunar material to colonies in space. Masses of lunar material are accelerated to lunar escape by a tracked magnetically levitated mass driver; aim precision is to 1 km miss distance at L5 per mm/sec velocity error at the lunar surface. Mass driver design and linear synchronous motor drive design are discussed; laser-sensed checkpoints aid in velocity and directional precision. Moon-L5 trajectories are calculated. The design of the L5 construction station, or 'catcher vehicle,' is described; loads are received by chambers operating in a 'Venus flytrap' mode. Further research studies needed to round out the concept are listed explicitly.

Heppenheimer, T. A.↗
NASA NTRS2018

A Breakthrough Propulsion Architecture for Interstellar Precursor Missions: Phase I Final Report

Our breakthrough propulsion architecture is an innovative way to take advantage of kilometer-scale, multi-hundred megawatt, space-based, phased-array lasers to enable rapid transportation throughout the solar system. In this architecture, the laser would beam power over distances of up to 40 AU increasing the available power density relative to solar insolation by two orders of magnitude. The receiving vehicle would have a photovoltaic array with cells tuned to the laser frequency that outputs a voltage of 6 kV to directly-drive a lithium-fueled gridded ion thruster system at an ultra-high specific impulse of 40,000 s. Such a system could enable final spacecraft speeds of greater than 40 AU/year, potentially enabling missions to the solar gravity lens focus at 550 AU in less than 15 years. This is the propulsion architecture of the 22nd century.

Brophy, John↗
DOE OSTI2025

Printed Targets with Micron-Scale Feature Patterns for the Study of Ablator Defects on OMEGA

As per present models, laser imprint and implosion symmetry are insufficient to account for observed performance degradation of direct-drive cryogenic fusion implosions. More and better data are needed on ablator defects as a source of hydrodynamic instability and mix. To investigate this, a series of OMEGA experimental campaigns is underway to study isolated target defects. Key requirements are systematic variation of the laser intensity and pulse shape at shot, with highly controlled defect type, geometry, and location. Here, given the need for sub-micron resolution and precise registration of multiple features, two-photon polymerization (TPP) printing was identified as an ideal method to fabricate these targets. TPP printing has enabled controlled formation of designed domes, divots, and vacuoles for studying the combined effect of size and proximity of these features on the hydro performance.

Two-photon polymerization printing↗
NASA NTRS1985

Directed-energy process technology efforts

A summary of directed-energy process technology for solar cells was presented. This technology is defined as directing energy or mass to specific areas on solar cells to produce a desired effect in contrast to exposing a cell to a thermal or mass flow environment. Some of these second generation processing techniques are: ion implantation; microwave-enhanced chemical vapor deposition; rapid thermal processing; and the use of lasers for cutting, assisting in metallization, assisting in deposition, and drive-in of liquid dopants. Advantages of directed energy techniques are: surface heating resulting in the bulk of the cell material being cooler and unchanged; better process control yields; better junction profiles, junction depths, and metal sintering; lower energy consumption during processing and smaller factory space requirements. These advantages should result in higher-efficiency cells at lower costs. The results of the numerous contracted efforts were presented as well as the application potentials of these new technologies.

Alexander, P.↗
DOE OSTI2025

Amplification of laser imprint in the presence of strong, externally imposed, target-normal magnetic fields

Here, an experiment was performed on the OMEGA EP Laser System to investigate the effects of magnetic fields on laser imprint. A 30 µ⁢m thick CH target was driven by a single beam delivering 3.0 kJ of UV energy in a 5 ns square pulse without smoothing by spectral dispersion. The Rayleigh-Taylor amplification of this beam's imprint on the target surface was monitored using face-on gated x-ray radiography from a Gd backlighter. Magnetic fields of up to 45 T were applied normal to the target surface. Analysis of the resulting radiographs shows a 60 ± 13% increase in the spectrally resolved surface perturbation amplitudes, consistent at all times and for all unsaturated frequencies. This consistency indicates that the increase in perturbation amplitudes was due to a change in the initial amplitudes rather than Rayleigh-Taylor growth. This is supported by the trajectory of individual modes and the inferred time-averaged perturbation growth rates. Laser imprint is therefore inferred to have increased due to strong magnetic fields that remain in the conduction zone of the target, suppressing off-axis electron motion and limiting the effects of thermal smoothing.

direct drive↗
DOE OSTI2025

Light field–controlled PHz currents in intrinsic metals

Oriented electric currents in metals are routinely driven by applying an external electric potential. Although the response of electrons to the external electric fields occurs within attoseconds, conventional electronics do not use this speed potential. Ultrashort laser pulses with controlled shapes of electric fields that switch direction at petahertz frequencies open perspectives for driving currents in metals. Light field–driven currents were demonstrated in various media including dielectrics, semiconductors, and topological insulators. Now, our research question is whether we can drive and control orders of magnitude more charge carriers in metals enabling ultrafast switching with practically low-energy, picojoule-level pulses. Here, we demonstrate the interaction of light with nanometer-thick metallic layers, which leads to a generation of light field–controlled electric currents. We show that the implantation of metallic layers into a dielectric matrix leads to up to 40 times increase of the sensitivity in contrast to a bare dielectric, decreasing the intensity threshold for lightwave electronics.

Fehér, Beatrix [HUN-REN Wigner Research Centre for↗
DOE OSTI2025

Automated and highly parallelized Bayesian optimization scheme for direct drive fusion experiments on OMEGA

Finding the optimal implosion design on existing experimental facilities for inertial confinement fusion requires an exhaustive search of the vast design parameter space. This is infeasible both with experiments and with simulations. Consequently, a large fraction of the experimentally realizable design space remains unexplored, and new design schemes are challenging to optimize in a reasonable time frame. On the OMEGA laser facility, predictive machine learning models have been developed to accurately forecast the result of an experiment using only inexpensive simulations and the large dataset of prior experimental data. However, the full design space remains vast enough to be unassailable with simple optimization techniques. Here we develop an automated and optimally parallel Bayesian optimization algorithm that can entirely optimize the target and pulse shape of a direct-drive ICF implosion under a given design paradigm. We use this algorithm to find a markedly improved design for the performance implosions on OMEGA that is predicted to hydroequivalently scale to ignition at 2.15 MJ.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Studies of localized mix and asymmetry caused by the stalk in inertial fusion experiments at OMEGA

In an inertially confined fusion experiment, a capsule of fusion fuel is compressed to high temperatures and densities using lasers, creating a hot plasma in which thermonuclear fusion reactions take place. To achieve efficient conversion of laser energy to fuel heating, the implosion must be as spherically symmetric as possible. One common source of asymmetry that degrades performance is the stalk and glue spot that hold the capsule in place before the experiment. The exact nature and magnitude of this perturbation had not been previously quantified. In this work, inertially confined fusion experiments were executed with an additional stalk on the capsule to measure and quantify the effect of the stalk and glue spot on the symmetry and performance. It is found that the stalk drives low-mode asymmetry by shadowing the laser drive on the part of the shell near the glue spot, enhancing the hot-spot velocity toward the stalk by 40–80 km/s and elongating the hot-spot along the stalk axis. It is also found that localized mix due to the additional stalk has a negligible effect on implosion performance. Two-dimensional radiation-hydrodynamic simulations using the xRAGE code reproduce the direction of the experimentally observed change to hot-spot velocity and implosion performance metrics, but not the observed elongation, suggesting that this feature results from an interaction between stalk perturbations and other preexisting asymmetry seeds, such as laser drive asymmetry.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Field-resolved observation of exciton coherence in a van der Waals magnet

The emergence of coherence among electronic quasiparticles underlies collective quantum phenomena from superconductivity to superradiance. In semiconductors, exciton coherence is generally thought to decay rapidly due to scattering and dephasing, limiting its persistence on ultrafast timescales. Here, in this work, we demonstrate a light-field-driven mechanism that creates and stabilizes exciton coherence in the layered antiferromagnet CrSBr. We directly record the coherent optical field emitted by excitons and track in real time how a deterministic phase, imprinted by the excitation laser, drives incoherent excitons to synchronize into a collective state. This ensemble remains phase coherent for more than 2 ps, whereas its resonance energy undergoes an ultrafast modulation mediated by spin and lattice interactions. The time-resolved field evolution indicates that the multiple peaks seen in conventional spectra originate from a single excitonic resonance subject to dynamic energy modulation. Our findings establish optical phase imprinting as a mechanism to control and sustain collective order in semiconducting magnets, bridging light-driven dynamics with excitonic and magnetic correlations in layered quantum materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Extreme-ultraviolet spatiotemporal vortices via high harmonic generation

Spatiotemporal optical vortices (STOVs) are space–time structured light pulses with a unique topology that couples spatial and temporal domains and carry transverse orbital angular momentum (OAM). Up to now, their generation has been limited to the visible and infrared regions of the spectrum. During the last decade, it was shown that through the process of high-order harmonic generation, it is possible to upconvert spatial optical vortices that carry longitudinal OAM from the near-infrared into the extreme-ultraviolet (EUV), thereby producing vortices with distinct femtosecond and attosecond structure. In this work, we demonstrate theoretically and experimentally the generation of EUV spatiotemporal and spatiospectral vortices using near-infrared STOV driving laser pulses. Here, we use analytical expressions for focused STOVs to perform macroscopic calculations of high-order harmonic generation that are directly compared to the experimental results. As STOV beams are not eigenmodes of propagation, we characterize the highly charged EUV STOVs in both the near and far fields to show that they represent conjugated spatiotemporal and spatiospectral vortex pairs. Our work provides high-frequency light beams topologically coupled at the nanometre/attosecond scales domains with transverse OAM that could be suitable to explore electronic dynamics in magnetic materials, chiral media and nanostructures.

High-harmonic generation↗
DOE OSTI2025

Correlating hot-electron preheat from the two-plasmon decay instability to $ρR$ degradation for direct-drive implosions on OMEGA

Focused experiments were performed with the goal of isolating the impact of hot-electron preheat on compression in deuterium–tritium (DT) layered, direct-drive implosions on OMEGA. Preheat from the hot-electrons generated by two-plasmon–decay (TPD) activity was varied through the incident laser intensity, with the total preheat energy deposited into unablated DT fuel being inferred using hard x-ray measurements. Results show a clear correlation between the inferred preheat levels and $ρR$ degradation that is consistent with a derived, 1D preheat model. A fit to the results also provides an estimated range of $ρR$ degradation from non-preheat sources for the adiabat ≈5 implosions used in this study. A follow-up study using targets containing Si-doped (5.5%) CH ablators (CHSi) demonstrated results consistent with mid-Z dopants mitigating TPD activity by showing these targets had almost no $ρR$ degradation as the laser intensity was increased up to levels previously considered damaging.

Doping↗
DOE OSTI2025

Correlating energy density induced residual stress, porosity, and mechanical property variations in directed energy deposition using neutron diffraction and imaging techniques

In a directed energy deposition (DED) process, the energy density deposited into the materials drives the structure and properties. The energy density is influenced by several printing parameters, such as laser power, hatch spacing, scanning speed, etc. In this study, 316L stainless steels samples were fabricated with varying hatch spacing aiming to induce variations in sample microstructure and properties. A combination of techniques including engineering neutron diffraction, neutron computed tomography, and tensile testing, were employed to correlate the structure and macroscopic properties. Porosity was predominantly observed at the bottom of the deposited materials and was effectively reduced by decreased hatch spacing. Correlatively, compressive residual stress was observed at the bottom of the specimens, while internal stress is largely determined by the hatch spacing. The residual stress in general decreases as the hatch spacing decreases. The maximum ultimate tensile strength (UTS) was found to increase from 517.4 to 528.6 MPa with a strain increased from 0.847 to 0.897 as the hatch spacing decreased from 0.45 to 0.42 mm. However, further increase in energy density by reducing the hatch spacing resulted in a significant decrease in UTS (as low as 452 MPa). This work provides new insights from bulk non-destructive techniques into correlating energy density induced residual stress, porosity, and mechanical property variations in directed energy deposition.

316L stainless steel↗
DOE OSTI2026

Performance enhancement of direct-drive shock-augmented ignition inertial fusion implosions through shock timing optimization

Shock-augmented ignition (SAI) [R. H. H. Scott et al., Phys. Rev. Lett. 129, 195001 (2022)] is an alternative inertial confinement fusion concept that is designed to achieve high energy gain by combining improved resilience to instabilities with enhanced fuel compression. In SAI, lower implosion velocities can improve hydrodynamic stability and limited laser intensities reduce the excitation of detrimental laser-plasma instabilities, enabling greater areal density accumulation. Here we report an experimental investigation of SAI using a series of warm D 2 implosions. By timing the augmenting shock to arrive at the implosion center immediately prior to peak compression, the areal density and hot-spot pressure increase by 50% and 112%, respectively, relative to unoptimized designs. Ignition-scale simulations reproduce the observed timing dependence and demonstrate the potential of SAI for inertial fusion energy.

Direct drive↗
NASA NTRS1990

Integrated Optoelectronic Interface

Proposed optoelectronic integrated-circuit device serves as "universal" or standard interface for transmission and reception of digital and analog signals in communication, data-processing, and control systems. Eliminates need for custom design of interface circuitry in sense that it embodies "master-chip" design easily adaptable to use with specific equipment. Includes directly modulated semiconductor laser to generate light signals for transmission along optical fiber; positive/intrinsic/negative, avalanche, or other photodiode to detect light signals received along another optical fiber;and driving, synchronizing, preamplifying, and signal-regenerating circuitry. Muliplexes electronic signals before transmission and/or demultiplexes electronic signals after reception.

Katz, Joseph↗
DOE OSTI2025

Inference of three-dimensional hot-spot and shell morphology in inertial confinement fusion experiments using a convolutional neural network

The performance of inertial confinement fusion (ICF) implosions is sensitive to the three-dimensional (3D) morphology of the hot-spot and shell configurations. The ability to infer shell-mass uniformity and reconstruct 3D hot spots is crucial for quantifying the degradation of ignition criteria and improving symmetry in ICF implosion experiments. In this work, we present a deep-learning convolutional neural network (CNN) for reconstructing 3D hot-spot and shell structures for ICF capsules. The 3D geometry of the hot spot is reconstructed from x-ray images measured from multiple lines of sight on OMEGA. The shell configuration is inferred indirectly through machine learning using a convolutional neural network extensively trained on a dec3d simulation database. This simulation-dependent approach yields consistent agreement between reconstructed 3D shell densities and machine-learning optimized dec3d simulation results. This work demonstrates a CNN framework that successfully reconstructs 3D capsule structures from two-dimensional images in ICF implosions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1999

Microgravity Transport Phenomena Experiment (MTPE) Overview

The Microgravity Transport Phenomena Experiment (MTPE) is a fluids experiment supported by the Fundamentals in Biotechnology program in association with the Human Exploration and Development of Space (BEDS) initiative. The MTP Experiment will investigate fluid transport phenomena both in ground based experiments and in the microgravity environment. Many fluid transport processes are affected by gravity. Osmotic flux kinetics in planar membrane systems have been shown to be influenced by gravimetric orientation, either through convective mixing caused by unstably stratified fluid layers, or through a stable fluid boundary layer structure that forms in association with the membrane. Coupled transport phenomena also show gravity related effects. Coefficients associated with coupled transport processes are defined in terms of a steady state condition. Buoyancy (gravity) driven convection interferes with the attainment of steady state, and the measurement of coupled processes. The MTP Experiment measures the kinetics of molecular migration that occurs in fluids, in response to the application of various driving potentials. Three separate driving potentials may be applied to the MTP Experiment fluids, either singly or in combination. The driving potentials include chemical potential, thermal potential, and electrical potential. Two separate fluid arrangements are used to study membrane mediated and bulk fluid transport phenomena. Transport processes of interest in membrane mediated systems include diffusion, osmosis, and streaming potential. Bulk fluid processes of interest include coupled phenomena such as the Soret Effect, Dufour Effect, Donnan Effect, and thermal diffusion potential. MTP Experiments are performed in the Microgravity Transport Apparatus (MTA), an instrument that has been developed specifically for precision measurement of transport processes. Experiment fluids are contained within the MTA fluid cells, designed to create a one dimensional flow geometry of constant cross sectional area, and to facilitate fluid filling and draining operations in microgravity. The fluid cells may be used singly for bulk solutions, or in a Stokes diaphragm configuration to investigate membrane mediated phenomena. Thermal and electrical driving potentials are applied to the experiment fluids through boundary plates located at the ends of the fluid cells. In the ground based instrument, two constant temperature baths circulate through reservoirs adjacent to the boundary plates, and establish the thermal environment within the fluid cells. The boundary plates also serve as electrodes for measurement and application of electrical potentials. The Fluid Manipulation System associated with the MTA is a computer controlled system that enables storage and transfer of experiment fluids during on orbit operations. The system is used to automatically initiate experiments and manipulate fluids by orchestrating pump and valve operations through scripted sequences. Unique technologies are incorporated in the MTA for measurement of fluid properties. Volumetric Flow Sensors have been developed for precision measurement of total fluid volume contained within the fluid cells over time. This data is most useful for measuring the kinetics of osmosis, where fluid is transported from one fluid cell to another through a semipermeable membrane. The MicroSensor Array has been designed to perform in situ measurement of several important fluid parameters, providing simultaneous measurement of solution composition at multiple locations within the experiment fluids. Micromachined sensors and interface electronics have been developed to measure temperature, electrical conductivity, pH, cation activity, and anion activity. The Profile Refractometer uses a laser optical system to directly image the fluid Index of Refraction profile that exists along the MTA fluid cell axis. A video system acquires images of the RI profile over time, and records the transport kinetics that occur upon application of chemical, thermal, or electrical driving potentials. Image processing algorithms have been developed to analyze the refractometer images on a pixel by pixel basis, calibrating and scaling the measured Index of Refraction profile to correlated solution properties of interest such as density, concentration, and temperature. Additional software has been developed to compile the processed images into a three dimensional matrix that contains fluid composition data as a function of experiment time and position in the fluid cell. These data are combined with data from the other sensor systems, and analyzed in the context of transport coefficients associated with the various transport phenomena. Analysis protocols have been developed to measure the transient kinetics, and steady state distribution of fluid components that occur in response to the applied driving potentials. The results are expressed in terms of effective transport coefficients. Experiments have been performed using a variety of solutes, and results generated are that are in agreement with published transport coefficient values.

Mason, Larry W.↗
NASA NTRS2000

Quantitative Measurements of Nitric Oxide Concentration in High-Pressure, Swirl-Stabilized Spray Flames

Lean direct-injection (LDI) spray flames offer the possibility of reducing NO(sub x) emissions from gas turbines by rapid mixing of the liquid fuel and air so as to drive the flame structure toward partially-premixed conditions. We consider the technical approaches required to utilize laser-induced fluorescence methods for quantitatively measuring NO concentrations in high-pressure LDI spray flames. In the progression from atmospheric to high-pressure measurements, the LIF method requires a shift from the saturated to the linear regime of fluorescence measurements. As such, we discuss quantitative, spatially resolved laser-saturated fluorescence (LSF), linear laser-induced fluorescence (LIF), and planar laser-induced fluorescence (PLIF) measurements of NO concentration in LDI spray flames. Spatially-resolved LIF measurements of NO concentration (ppm) are reported for preheated, LDI spray flames at pressures of two to five atmospheres. The spray is produced by a hollow-cone, pressure-atomized nozzle supplied with liquid heptane. NO is excited via the Q(sub 2)(26.5) transition of the gamma(0,0) band. Detection is performed in a two nanometer region centered on the gamma(0,1) band. A complete scheme is developed by which quantitative NO concentrations in high-pressure LDI spray flames can be measured by applying linear LIF. NO is doped into the reactants and convected through the flame with no apparent destruction, thus allowing a NO fluorescence calibration to be taken inside the flame environment. The in-situ calibration scheme is validated by comparisons to a reference flame. Quantitative NO profiles are presented and analyzed so as to better understand the operation of lean-direct injectors for gas turbine combustors. Moreover, parametric studies are provided for variations in pressure, air-preheat temperature, and equivalence ratio. Similar parametric studies are performed for lean, premixed-prevaporized flames to permit comparisons to those for LDI flames. Finally, PLIF is expanded to high pressure in an effort to quantify the detected fluorescence image for LDI flames. Success is achieved by correcting the PLIF calibration via a single-point LIF measurement. This procedure removes the influence of any preferential background that occurs in the PLIF detection window. In general, both the LIF and PLIF measurements verify that the LDI strategy could be used to reduce NO(sub x) emissions in future gas turbine combustors.

Cooper, Clayton S.↗
DOE OSTI2025

Dislocation‐Driven Formation of Oriented Macroperiodic Metastructures of Curved Single Crystal Lattices in Glass

Abstract Single crystals fabricated in glass by localized heating can develop uniquely deformed lattices stabilized by the surrounding amorphous medium. The development of lattice curvature appears to be intrinsic to the crystal growth process in some systems, while the result of the locally changing crystallography in others. In this work, a model laser‐fabricated rotating lattice Sb 2 S 3 crystal grown in stoichiometric glass is used to demonstrate fabrication of novel macroperiodic metastructures that utilize intrinsic lattice curvature superimposed with subtle crystallographic influences. The limited availability of slip systems drives the lattice curvature magnitude to vary with crystal growth direction, maximizing for lattices aligned with the predominant Burgers vector along with corresponding increases in dislocation density. Misaligned lattice orientations form smaller secondary lattice curvatures arising from misaligned Burgers vectors with further elastic contributions. Over extended crystal growth, these secondary components align the lattice to rotate about either the <001> or <010> crystal axes forming repeating metastructures of lattice orientation with periodicity 20–160 microns in length. The mechanistic approach used in this work may be expanded to other systems with known slip systems to better understand and design macroperiodic metastructures.

36 MATERIALS SCIENCE↗