Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “laser CVD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

49 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Cryogenically enhanced quasi-optical resonator for megawatt pulsed millimeter-wave sources

We report the design, cryogenic optimization, and performance modeling of a compact quasi-optical ring resonator intended to compress microwaves pulses at 170 and 250 GHz to the megawatt level. By combining ultra-low-loss CVD diamond and gold-doped silicon wafers with high-RRR copper mirrors, the calculated unloaded quality factor exceeds 4.3 × 10 5 at 20 K and yields simulated gains up to $\mathscr{G}$ = 4.1 × 10 3 . Coupling the resonator with a laser-driven semiconductor switch described by an extended Vogel model shows that 1 MW, nanosecond pulses can be generated from only 445 W of microwave drive power while dissipating 272 W into the cryostat. A practical cooling architecture using two Gifford–McMahon stages (20 and 80 K) is proposed, demonstrating that high-repetition-rate (10–20 kHz) operation is feasible with commercially available cryocoolers. The results outline a clear path toward cost-effective, table-top sources for extreme-ultraviolet lithography, dynamic nuclear polarization, and fusion systems.

Panisset, Constant [Ecole Polytechnique Federale L↗
DOE OSTI2020

Grinding of additively manufactured silicon carbide surfaces for optical applications

Many of the properties of Silicon carbide (SiC) are advantageous for optical applications, such as telescope mirrors and industrial laser systems. However, the base shapes of complex components are costly and difficult to manufacture. Leveraging additive manufacturing, near net complex components are readily processed. In this work, we investigate the post processing of additively manufactured SiC (AM SiC) compared to chemical vapor deposited (CVD) SiC. The specific grinding energy for the AM SiC was lower than CVD, however the trends were the same. A specular finish was observed on both materials but the AM SiC finish was limited due to residual porosity.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Unveiling defect-mediated carrier dynamics in monolayer semiconductors by spatiotemporal microwave imaging

The optoelectronic properties of atomically thin transition-metal dichalcogenides are strongly correlated with the presence of defects in the materials, which are not necessarily detrimental for certain applications. For instance, defects can lead to an enhanced photoconduction, a complicated process involving charge generation and recombination in the time domain and carrier transport in the spatial domain. Here, we report the simultaneous spatial and temporal photoconductivity imaging in two types of WS 2 monolayers by laser-illuminated microwave impedance microscopy. The diffusion length and carrier lifetime were directly extracted from the spatial profile and temporal relaxation of microwave signals, respectively. Time-resolved experiments indicate that the critical process for photoexcited carriers is the escape of holes from trap states, which prolongs the apparent lifetime of mobile electrons in the conduction band. As a result, counterintuitively, the long-lived photoconductivity signal is higher in chemical-vapor deposited (CVD) samples than exfoliated monolayers due to the presence of traps that inhibits recombination. Overall, our work reveals the intrinsic time and length scales of electrical response to photoexcitation in van der Waals materials, which is essential for their applications in optoelectronic devices.

42 ENGINEERING↗
DOE OSTI2024

Materials genome innovation for computational software (magics) center

Functional layered material (LM) architectures will dominate nanomaterials science in this century. We have developed theory, modeling, simulation, and software and data tools that enhance understanding and AI guide synthesis, enable characterization of complex structures, and improve capabilities in the predictive design and growth of LMs. Research at the Center has focused on: Computational synthesis and characterization: AI guided synthesis and experimental synthesis of stacked LMs with tailored properties via optimized chemical vapor deposition (CVD) growth and liquid-phase exfoliation; study defects, edges, grain boundaries, wrinkling of atomic layers and their effects on chemical, mechanical, electrical, and optical properties. Far-from-equilibrium processes: Joint experimental and simulation based probe of electronic processes with NAQMD and ultrafast X-ray free-electron laser (XFEL) and ultrafast electron diffraction (UED) facilities at Stanford. Experimentally validate NAQMD by ultrafast electron diffraction and X-ray spectroscopy studies of structural and excited state dynamics, shape fluctuations, and phonon dynamics. Scalable software: Simulation engines for desktop-to-exascale platforms using low-overhead, linear-scaling QMD algorithms; divide-conquer-recombine NAQMD with electronic excitations; extended-Lagrangian reactive molecular dynamics (RMD), machine learning (ML) based neural-network quantum molecular dynamics (NNQMD), and super-state accelerated molecular dynamics (AMD) and kinetic Monte Carlo codes; thermal and electrical transport software; and design 3D architectures of LMs with desired functionality using scalable software. Distribution of software and data, and training: Software and simulation-experimental data generated within the Center are distributed to the materials science community via Berkeley Materials Project (MP) framework. We have also organized three workshops for software distribution and training at USC (Nov. 2017, Mar. 2018) and Gaithersburg, MD (Nov. 2018) to train researchers, with the last one in focused on underrepresented groups, in collaboration with Howard University which is one of the largest HBCUs. The Center supported a total of 46 personnel and 6 undergraduate students. These include 14 faculty, 11 postdoctoral research associates, 20 graduate research assistants, and mentored 6 undergraduate students. This resulted in the publications of 63 research papers that include 46 publications on Reactive and Quantum Dynamics Simulations, 13 publications on Machine Learning for Quantum Materials, and 4 publications on Quantum Computing.

2D Materials↗
NASA NTRS1992

Low thrust chemical rocket technology

An on-going technology program to improve the performance of low thrust chemical rockets for spacecraft on-board propulsion applications is reviewed. Improved performance and lifetime is sought by the development of new predictive tools to understand the combustion and flow physics, introduction of high temperature materials and improved component designs to optimize performance, and use of higher performance propellants. Improved predictive technology is sought through the comparison of both local and global predictions with experimental data. Predictions are based on both the RPLUS Navier-Stokes code with finite rate kinetics and the JANNAF methodology. Data were obtained with laser-based diagnostics along with global performance measurements. Results indicate that the modeling of the injector and the combustion process needs improvement in these codes and flow visualization with a technique such as 2-D laser induced fluorescence (LIF) would aid in resolving issues of flow symmetry and shear layer combustion processes. High temperature material fabrication processes are under development and small rockets are being designed, fabricated, and tested using these new materials. Rhenium coated with iridium for oxidation protection was produced by the Chemical Vapor Deposition (CVD) process and enabled an 800 K increase in rocket operating temperature. Performance gains with this material in rockets using Earth storable propellants (nitrogen tetroxide and monomethylhydrazine or hydrazine) were obtained through component redesign to eliminate fuel film cooling and its associated combustion inefficiency while managing head end thermal soakback. Material interdiffusion and oxidation characteristics indicated that the requisite lifetimes of tens of hours were available for thruster applications. Rockets were designed, fabricated, and tested with thrusts of 22, 62, 440 and 550 N. Performance improvements of 10 to 20 seconds specific impulse were demonstrated. Higher performance propellants were evaluated: Space storable propellants, including liquid oxygen (LOX) as the oxidizer with nitrogen hydrides or hydrocarbon as fuels. Specifically, a LOX/hydrazine engine was designed, fabricated, and shown to have a 95 pct theoretical c-star which translates into a projected vacuum specific impulse of 345 seconds at an area ratio of 204:1. Further performance improvment can be obtained by the use of LOX/hydrogen propellants, especially for manned spacecraft applications, and specific designs must be developed and advanced through flight qualification.

Schneider, Steven J.↗
NASA NTRS1978

The Array Automated Assembly Task for the Low Cost Solar Array Project, Phase 2

During the program a process sequence was proposed and tested for the fabrication of dendritic welb silicon into solar modules. This sequence was analyzed as to yield and cost and these data suggest that the price goals of 1986 are attainable. Specifically, it was shown that a low cost POCL3 is a suitable replacement for the semiconductor grade, and that a suitable CVD oxide can be deposited from a silane/air mixture using a Silox reactor. A dip coating method was developed for depositing an antireflection coating from a metalorganic precursor. Application of photoresist to define contact grids was made cost effective through use of a dip coating technique. Electroplating of both Ag and Cu was shown feasible and cost effective for producing the conductive metal grids on the solar cells. Laser scribing was used to separate the cells from the dendrites without degradation. Ultrasonic welding methods were shown to be feasible for interconnecting the cells. A study of suitable low cost materials for encapsulation suggest that soda lime glass and phenolic filled board are preferred.

Campbell, R. B.↗
DOE OSTI2022

Tungsten doped diamond shells for record neutron yield inertial confinement fusion experiments at the National Ignition Facility

We report on fabrication and characterization of layered, tungsten doped, spherical about 2 mm diameter microcrystalline diamond ablator shells for inertial confinement fusion (ICF) experiments at the National Ignition Facility. As previously reported, diamond ICF ablator shells can be fabricated by chemical vapor deposition (CVD) on solid spherical silicon mandrels using an ellipsoidal microwave plasma reactor. In the present work, we further developed these ablator shells by embedding a W -doped diamond layer sandwiched between two undoped diamond regions. W incorporation in diamond was achieved by adding tungsten hexacarbonyl to the CH 4 /H 2 CVD feed gas. We observe that the W doping concentration decreases with increasing deposition rate which, in turn, is controlled by adjusting the total gas pressure. Cross sectional microstructural analysis reveals sharp interfaces between doped and undoped regions of the diamond shell and uniform W distribution with concentrations up to about 0.3 at.%. At higher W concentrations (>0.3 at.%) formation of tungsten carbide precipitates is observed. Using a 3-shock 1.6 MJ laser pulse, the targets described in this work produced the first laser driven implosion to break the 1 × 10 16 neutron yield barrier, followed by experiments (described in future publications) with similar targets and slightly more laser energy producing yields as high as 4 × 10 17 .

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Enabling a novel approach to a controlled fabrication of 1D crystalline nanowires on suspended microstructures of arbitrary geometries using two direct-writing technologies

Recent progresses in additive manufacturing have inspired new technologies, such as direct laser writing technique, based on two-photon polymerization (2 PP), which complements and further enriches the nanofabrication tools portfolio. Here, we combine 2 PP and our mask-free scanning probe assisted ‘direct-write patterning’ (DWP) method to allow for: a) the fabrication of micro-bridge structures with sub-micrometer resolution, b) selective synthesis of crystalline ZnO nanowires at predefined locations, respectively. This synergistic approach enables cantilever probe patterning of catalysts directly on suspended micro-bridges for in-situ CVD growth of nanoscale material, in a templated manner. The study reported here represents the first proof-of-concept experiments demonstrating versatile and scalable methodology, which can be applied and straightforwardly extended to grow a variety of other nanomaterials, in a controlled and selective fashion, on freestanding micro/nanoscale structures, whose size and geometry can be conveniently varied via templating of sacrificial 2 PP polymeric scaffolds. Furthermore, the demonstration of the possibility to integrate this new approach with the conventional lithography techniques provides a step forward to the development of the novel class of hybrid polymer-silicon-1D or -2D materials, and systems. The quality of the produced ZnO nanowire assemblies was assessed using several physical characterization methods.

36 MATERIALS SCIENCE↗
NASA NTRS2003

Metal Nanoparticle Catalysts for Carbon Nanotube Growth

Work this summer involved and new and unique process for producing the metal nanoparticle catalysts needed for carbon nanotube (CNT) growth. There are many applications attributed to CNT's, and their properties have deemed them to be a hot spot in research today. Many groups have demonstrated the versatility in CNT's by exploring a wide spectrum of roles that these nanotubes are able to fill. A short list of such promising applications are: nanoscaled electronic circuitry, storage media, chemical sensors, microscope enhancement, and coating reinforcement. Different methods have been used to grow these CNT's. Some examples are laser ablation, flame synthesis, or furnace synthesis. Every single approach requires the presence of a metal catalyst (Fe, Co, and Ni are among the best) that is small enough to produce a CNT. Herein lies the uniqueness of this work. Microemulsions (containing inverse micelles) were used to generate these metal particles for subsequent CNT growth. The goal of this summer work was basically to accomplish as much preliminary work as possible. I strived to pinpoint which variable (experimental process, metal product, substrate, method of application, CVD conditions, etc.) was the determining factor in the results. The resulting SEM images were sufficient for the appropriate comparisons to be made. The future work of this project consists of the optimization of the more promising experimental procedures and further exploration onto what exactly dictated the results.

Pierce, Benjamin F.↗
DOE OSTI2021

Carbon nanospike coated nanoelectrodes for measurements of neurotransmitters

Here, carbon nanoelectrodes enable the detection of neurotransmitters at the level of single cells, vesicles, synapses and small brain structures. Previously, the etching of carbon fibers and 3D printing based on direct laser writing have been used to fabricate carbon nanoelectrodes, but these methods lack the ability of mass manufacturing. In this paper, we mass fabricate carbon nanoelectrodes by growing carbon nanospikes (CNSs) on metal wires. CNSs have a short, dense and defect-rich surface that produces remarkable electrochemical properties, and they can be mass fabricated on almost any substrate without using catalysts. Tungsten wires and niobium wires were electrochemically etched in batch to form sub micrometer sized tips, and a layer of CNSs was grown on the metal wires using plasma-enhanced chemical vapor deposition (PE-CVD). The thickness of the CNS layer was controlled by the deposition time, and a thin layer of CNSs can effectively cover the entire metal surface while maintaining the tip size within the sub micrometer scale. The etched tungsten wires produced tapered conical nanotips, while the etched niobium wires were long and thin. Both showed excellent sensitivity for the detection of outer sphere ruthenium hexamine and the inner sphere test compound ferricyanide. The CNS nanosensors were used for the measurement of dopamine, serotonin, ascorbic acid and DOPAC with fast-scan cyclic voltammetry. The CNS nanoelectrodes had a large surface area and numerous defect sites, which improved the sensitivity, electron transfer kinetics and adsorption. Finally, the CNS nanoelectrodes were compared with other nanoelectrode fabrication methods, including flame etching, 3D printing, and nanopipettes, which are slower to make and more difficult for mass fabrication. Thus, CNS nanoelectrodes are a promising strategy for the mass fabrication of nanoelectrode sensors for neurotransmitters.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1978

Laser-zone growth in a Ribbon-To-Ribbon (RTR) process. Silicon sheet growth development for the large area sheet task of the low-cost solar array project

A new calculation of the effects of thermal stresses during growth on silicon ribbon quality is reported. Thermal stress distributions are computed for ribbon growth under a variety of temperature profiles. A growth rate of 55 cu cm/min with a single ribbon was achieved. The growth of RTR ribbon with a fairly uniform parallel dendritic structure was demonstrated. Results with two approaches were obtained for reducing the Mo impurity level in polycrystalline feedstock. Coating the Mo substrate with Si3N4 does not effect thermal shear separation of the polyribbon; this process shows promise of improving cell efficiency and also increasing the useful life of the molybdenum substrate. A number of solar cells were fabricated on RTR silicon grown from CVD feedstock.

Baghdadi, A.↗
NASA NTRS1978

Progress towards high efficiency polycrystalline thin-film GaAs AMOS solar cells

Results of Ge film recrystallization using focused laser beams and GaAs film growth on such layers in the making of high efficiency thin-film AMOS solar cells are discussed. Since a conversion efficiency of 14% was obtained for an AMOS cell fabricated on sliced bulk polycrystalline GaAs, high efficiency cells are being developed by chemically vapor-depositing GaAs films on previously recrystallized evaporated Ge films to minimize the grain boundary (GB) effects. Schottky barrier solar cells made on sliced polycrystalline GaAs wafers were studied to investigate the effects of grain boundaries on cell properties and the potential efficiency of GaAs thin-film cells. Ge film recrystallization and the chemical vapor deposition (CVD) of the 2 to 3 micron thick GaAs films are described. AMOS solar cells with 100 Angstrom thick Ag metallization were made on CVD GaAs/recrystallized Ge/W substrates with an energy conversion efficiency of 8%.

Yeh, Y. C. M.↗
NASA NTRS2001

Low Temperature Growth of Nanostructured Diamond Films on Metals

The field of nanocrystalline diamond and tetrahedral amorphous carbon films has been the focus of intense experimental activity in the last few years for applications in field emission display devices, optical windows, and tribological coatings, The choice of substrate used in most studies has typically been silicon. For metals, however, the thermal expansion mismatch between the diamond film and substrate gives rise to thermal stress that often results in delamination of the film. To avoid this problem in conventional CVD deposition low substrate temperatures (less than 700 C) have been used, often with the incorporation of oxygen or carbon monoxide to the feedgas mixture. Conventionally grown CVD diamond films are also rough and would require post-deposition polishing for most applications. Therefore, there is an obvious need to develop techniques for deposition of well-adhered, smooth nano-structured diamond films on metals for various tribological applications. In our work, nanostructured diamond films are grown on a titanium alloy substrate using a two-step deposition process. The first step is performed at elevated temperature (820 C) for 30 minutes using a H2/CH4/N2 gas mixture in order to grow a thin (approx. 600 nm) nanostructured diamond layer and improve film adhesion. The remainder of the deposition involves growth at low temperature (less than 600 C) in a H2/CH4/O2 gas mixture. Laser reflectance Interferometry (LRI) pattern during growth of a nanostructured diamond film on Ti-6Al-4V alloy. The first 30 minutes are at a high temperature of 820 C and the rest of the film is grown at a low temperature of 580 T. The fringe pattern is observed till the very end due to extremely low surface roughness of 40 nm. The continuation of the smooth nanostructured diamond film growth during low temperature deposition is confirmed by in-situ laser reflectance interferometry and by post-deposition micro-Raman spectroscopy and surface profilometry. Similar experiments performed without the starting nanostructured diamond layer resulted in poorly adhered films with a more crystalline appearance and a higher surface roughness. This low temperature deposition of nanostructured diamond films on metals offers advantages in cases where high residual thermal stress leads to delamination at high temperatures.

Baker, Paul A.↗