Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “joining”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Status of Joining Thin Sheet and Thin Wall Tubes of 14YWT

Beginning this fiscal year, the FCRD research project initiated an investigation on joining thin sections of the advanced ODS 14YWT ferritic alloy. Friction stir welding (FSW) was investigated as a method to join thin plate and tubing of 14YWT since it is a solid state joining method that has been shown in past studies to be a promising method for joining plates of ODS alloys, such as 14YWT. However, this study will attempt to be the first to demonstrate if FSW can successfully join thin plates and thin wall tubing of 14YWT. In the first FSW attempt, a 1.06 cm thick plate of 14YWT (SM13 heat) was successfully rolled at 1000ºC to the target thickness of 0.1 cm with no edge cracking. This achievement is a highlight since previous attempts to roll 14YWT plates have resulted in extensive cracking. For the FSW run, a pin tool being developed by the ORNL FSW Process Development effort was used. The first FSW run successfully produced a bead-on-plate weld in the 0.1 cm thick plate. The quality of the weld zone appears very good with no evidence of large defects such as cavities. The microstructural characterization study of the bead-on-plate weld zone has been initiated to compare the results of the microstructure analysis with those obtained in the reference microstructural analysis of the 14YWT (SM13 heat) that showed ultra-fine grain size of 0.43 μm and a high number density of ~2-5 nm sizes oxygen-enriched nanoclusters.

42 ENGINEERING↗

Joining of dissimilar materials

A method of joining dissimilar materials having different ductility, involves two principal steps: Decoration of the more ductile material's surface with particles of a less ductile material to produce a composite; and, sinter-bonding the composite produced to a joining member of a less ductile material. The joining method is suitable for joining dissimilar materials that are chemically inert towards each other (e.g., metal and ceramic), while resulting in a strong bond with a sharp interface between the two materials. The joining materials may differ greatly in form or particle size. The method is applicable to various types of materials including ceramic, metal, glass, glass-ceramic, polymer, cermet, semiconductor, etc., and the materials can be in various geometrical forms, such as powders, fibers, or bulk bodies (foil, wire, plate, etc.). Composites and devices with a decorated/sintered interface are also provided.

36 MATERIALS SCIENCE↗

Microstructure and properties of ceramics and composites joined by plastic deformation.

A review is presented of the design of suitable materials systems for joining by high-temperature plastic deformation, details of the joining techniques, microstructures and properties of the resulting composite bodies, and prospects and limitation for this type of joining technology. Joining parameters and resulting forms are discussed for Al{sub 2}O{sub 3}/mullite particulate composites, Y{sub 2}O{sub 3}-stabilized ZrO{sub 2} particulate/Al{sub 2}O{sub 3} particulate and whisker-reinforced composites, hydroxyapatite bioceramics, La{sub 0.85}Sr{sub 0.15}MnO{sub 3} electronic ceramics, MgF{sub 2} optical ceramics, and Ni{sub 3}Al intermetallics. Results are contrasted with those obtained by other methods of joining brittle, high-temperature materials, with special focus on durability and mechanical properties.

36 MATERIALS SCIENCE↗

Corrosion behaviour of friction-bit-joined and weld-bonded AA7075-T6/galvannealed DP980

Joining of aluminium alloys 7075-T6 and galvannealed dual phase 980 steel was achieved by friction bit joining (FBJ) and weld-bonding (FBJ + adhesive) processes. Accelerated laboratory-scale corrosion tests were performed on both FBJ only and weld-bonded specimens to study joint strength under a corrosive environment. Static lap shear tests showed that both FBJ only and weld-bonded cases generally retained more than 80% of the joint strength of non-corroded specimens at the end of corrosion testing. The presence of Zn/Fe coating on the steel substrate resulted in improved corrosion resistance for FBJ specimens, compared to joints produced with bare steel. An optical microscopy was used for cross-sectional analysis of corroded specimens. Some corrosion on the joining bit was observed near the bit head. However, the joining bit was still intact on the steel substrate, indicating that the primary bond was sound.

36 MATERIALS SCIENCE↗

Corrosion and Tribocorrosion Behavior of Ti-B{sub 4}C Composites Joined with TiCuNi Brazing Alloy

Corrosion behavior of joined Ti-B{sub 4}C composites was evaluated in 9 g/L NaCl solution using cyclic polarization and electrochemical impedance spectroscopy. Tribocorrosion behavior was investigated by sliding against an alumina ball under open-circuit potential and potentiodynamic polarization. The results showed that joining did not negatively affect the corrosion behavior of the composites. Regarding tribocorrosion, while joining did not significantly influence the coefficient of friction and total wear volume loss, it resulted in slightly increased electrochemical activity under sliding. These results showed that brazing may be considered as a simple and low-cost technique for joining Ti-B{sub 4}C composites to be operated in tribocorrosive environments.

36 MATERIALS SCIENCE↗

Summary of Prior Work on Joining of Oxide Dispersion-Strengthened Alloys

There is a range of joining techniques available for use with ODS alloys, but care should be exercised in matching the technique to the final duty requirements of the joint. The goal for joining ODS alloys is a joint with no local disruption of the distribution of the oxide dispersion, and no significant change in the size and orientation of the alloy microstructure. Not surprisingly, the fusion welding processes typically employed with wrought alloys produce the least satisfactory results with ODS alloys, but some versions, such as fusion spot welding, and the laser and electron-beam welding technologies, have demonstrated potential for producing sound joints. Welds made using solid-state spot welding reportedly have exhibited parent metal properties. Thus, it is possible to employ processes that result in significant disruption of the alloy microstructure, as long as the processing parameters are adjustment to minimize the extent of or influence of the changes in the alloy microstructure. Selection among these joining approaches largely depends on the particular application and component configuration, and an understanding of the relationships among processing, alloy microstructure, and final properties is key. Recent developments have resulted in friction welding evolving to be a prime method for joining ODS sheet products, and variants of brazing/diffusion bonding have shown excellent promise for use with tubes and pipes. The techniques that come closest to the goal defined above involve solid-state diffusion bonding and, in particular, it has been found that secondary recrystallization of joints made by pulsed plasma-assisted diffusion can produce the desired, continuous, large alloy grain structure through the joint. Such joints have exhibited creep rupture failure at >82% of the load needed to fail the monolithic parent alloy at 1000 C.

36 MATERIALS SCIENCE↗

Low Activation Joining of SiC/SiC Composites for Fusion Applications: Tape Casting TiC+Si Powders

The use of SiC composites in fusion environments likely requires joining of plates using reactive joining or brazing. One promising reactive joining method uses solid-state displacement reactions between Si and TiC to produce Ti3SiC2 + SiC. We continue to explore the processing envelope for this joint for the TITAN collaboration in order to produce optimal joints to undergo irradiation studies in HFIR. One noted feature of the joints produced using tape-calendared powders of TiC+Si has been the large void regions that have been apparently unavoidable. Although the produced joints are very strong, these voids are undesirable. In addition, the tapes that were made for this joining were produced about 20 years ago and were aging. Therefore, we embarked on an effort to produce some new tape cast powders of TiC and Si that could replace our aging tape calendared materials.

Fusion↗

ODS Thin-wall Cladding Joining Technique Development

ABSTRACT The oxide dispersion strengthened (ODS) materials are typically fabricated by powder mechanical alloying to form uniform distribution of high concentration nanometer size oxide particles for exceptional high temperature mechanical strength and enhanced radiation tolerance. This report summarizes the recent development on the weld techniques of joining the ODS cladding to the endplug as a part of accident tolerant fuels (ATF) program for both advanced light water reactor (LWR) and advanced fuel cycle (AFC) with fast reactor fuel cladding. It is crucial for the weld of ODS material to maintain the uniform distribution and fine size of oxide particles in the matrix. Pressure Resistance Weld (PRW) is a solid state joining technique without melting therefore a preferred joining technique for ODS materials. Samples joined with PRW were pressure burst tested. Detailed microstructural characterization in this work includes non-destructive 3D x-ray ?m-resolution computer-tomography (?-CT), optical microscopy, SEM/EBSD for grain-orientation-mapping, TEM, STEM/ASTAR for high resolution grain orientation and phase mapping, and APT for high-resolution 3D composition analysis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Joining of Lightweight Dissimilar Materials by Friction Self-Piercing Riveting

In this work, we employed a unique solid-state joining process, friction self-piercing riveting (F-SPR), to join carbon fiber composites to the low-ductility magnesium alloy AZ31B. The localized frictional heat generated between the rotating rivet and the underside of the magnesium sheet softened and prevented crack generation in AZ31B. A consumable joining rivet was designed to join the selected material stacks by F-SPR. Lap shear tensile testing was used to assess the joint quality of specimens produced by F-SPR. The joint interface from the cross-sectioned F-SPR specimen was evaluated by optical microscopy.

Lim, Yong Chae↗

Next neighbors effect along the Ca–Sr–Ba-åkermanite join: Long-range vs. short-range structural features

An original approach has been developed herein to explore the correlations between short- and long-range structural properties of solid solutions. X-ray diffraction (XRD) and electronic absorption spectroscopy (EAS) data were combined on a (Ca,Sr,Ba){sub 2}(Mg{sub 0.7}Co{sub 0.3})Si{sub 2}O{sub 7} join to determine average and local distances, respectively. Instead of varying the EAS-active ion concentration along the join, as has commonly been performed in previous studies, the constant replacement of Mg{sup 2+} by a minimal fraction of a similar size cation (Co{sup 2+}) has been used to assess the effects of varying second-nearest neighbor cations (Ca, Sr, Ba) on the local distances of the first shell. A comparison between doped and un-doped series has shown that, although the overall symmetry of the Co-centered T1-site was retained, greater relaxation occurs at the CoO{sub 4} tetrahedra which become increasingly large and more distorted than the MgO{sub 4} tetrahedra. This is indicated by an increase in both the quadratic elongation (λ{sub T1}) and the bond angle variance (σ{sup 2}{sub T1}) distortion indices, as the whole structure expands due to an increase in size in the second-nearest neighbors. This behavior highlights the effect of the different electronic configurations of Co{sup 2+} (3d{sup 7}) and Mg{sup 2+} (2p{sup 6}) in spite of their very similar ionic size. Furthermore, although the overall symmetry of the Co-centered T1-site is retained, relatively limited (<10 deg) angular variations in O–Co{sup 2+}–O occur along the solid solution series and large changes are found in molar absorption coefficients showing that EAS Co{sup 2+}-bands are highly sensitive to change in the local structure. - Graphical abstract: Average (Mg–O) vs. local (Co–O{sub local}) tetrahedral bond distances in function of the average X cation radius in the (Ca,Sr,Ba){sub 2}(Mg{sub 0.7}Co{sub 0.3})Si{sub 2}O{sub 7} join. - Highlights: • New method to assess short- vs. long-range properties of non-ideal solid solutions. • Constant Co{sup 2+}-for-Mg replacement turns the Ca–Sr–Ba-åkermanite join EAS-active. • Co→Mg substitution does not produce any alteration in the average structure. • Relaxation around Co-tetrahedra scales with second-nearest neighbor cation radius. • Different electronic configurations of Co and Mg cause different local structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Joining of Aluminium Alloy Sheets by Rectangular Mechanical Clinching

A mechanical clinching has the advantage of low running costs. However, the joint strength is not high. To improve the maximum load of the joined sheets by a mechanical clinching, square and rectangular mechanical clinching were introduced. In the mechanical clinching, the two sheets are mechanically joined by forming an interlock between the lower and upper sheets by the punch and die. The joined length with the interlock was increased by the rectangular punch and die. The deforming behaviours of the sheets in the mechanical clinching were investigated, and then the interlock in the sheets had distribution in the circumference of the projection. Although the interlocks were formed in both projection side and diagonal, the interlock in the diagonal was smaller because of the long contact length between the lower sheet and the die cavity surface. The maximum load of the joined sheets by the rectangular mechanical clinching was two times larger than the load by the round mechanical clinching.

36 MATERIALS SCIENCE↗

Holographic optical assembly and photopolymerized joining of planar microspheres

The aim of this research is to demonstrate a holographically driven photopolymerization process for joining colloidal particles to create planar microstructures fixed to a substrate, which can be monitored with real-time measurement. Holographic optical tweezers (HOT) have been used to arrange arrays of microparticles prior to this work; here we introduce a new photopolymerization process for rapidly joining simultaneously handled microspheres in a plane. Additionally, we demonstrate a new process control technique for efficiently identifying when particles have been successfully joined by measuring a sufficient reduction in the particles’ Brownian motion. Furthermore, this technique and our demonstrated joining approach enable HOT technology to take critical steps toward automated additive fabrication of microstructures.

36 MATERIALS SCIENCE↗

Solid-State Joining of Magnesium Sheet to High-Strength Steel

Increasing the use of lightweight materials and implementing enabling manufacturing technologies are the two primary paths toward automotive weight reduction. In many situations, the ability to substitute light weight material requires a need to attach and join light weight material to existing steel substructures requiring dissimilar joining technologies. Dissimilar joining methods currently available in cost range for high volume automotive manufacturing face multiple challenges. The problem is exacerbated in the case of Magnesium alloy to steel joints because of their highly dissimilar nature and lack of mutual miscibility. Additionally, Magnesium’s poor room temperature ductility complicates the use of point fastening technologies. Two emerging solid-state joining technologies Friction Stir assisted Scribe welding (FaST) and Ultrasonic Welding (USW) that employ large amount of plastic deformation at the interface were used to investigate, develop, and understand dissimilar joints between Magnesium Alloy to DP590 Steel. Various process responses including interface temperatures, process forces, strain fields were captured during the development of the welding process. Variety of welded samples were tested and characterized to understand the relationship between welding conditions and joints microstructure and mechanical properties.

36 MATERIALS SCIENCE↗

Corrosion Protection and Dissimilar Material Joining for Next Generation Lightweight Vehicles

The Arconic Technology Center working with Honda R&D Americas, LLC and the Ohio State University evaluated the corrosion performance of several multi-material conditions and demonstrated the production worthiness of the Resistance Spot Riveting (RSR™) process. RSR is a new technology being developed by Howmet Fastening Systems (formerly Arconic, Inc.) that employs a fastener that is installed using conventional resistance spot welding equipment to produce multi-material joints. The goal of the 3-year project was to demonstrate the use of RSR to join aluminum to steel and aluminum to carbon fiber composites on a prototype scale. Deployment of this technology would help the automotive industry achieve an additional 10 to 20% weight reduction over high strength steels. These weight-savings to the body in white generally translates to 2.5-5.0% of overall vehicle curb weight. The resulting total weight-savings could provide a 1.5% to 3.0% total improvement in fuel efficiency for vehicles that incorporate RSR for multi-material joining. The RSR technology addresses several production barriers to achieving DOE’s fuel efficiency targets including eliminating the need of additional capital for new joining technologies and the flexibility to process conventional steel and multi-material structures with the same equipment. Additionally, the trend towards ultra-high strength steels limits the availability of conventional joining technologies that can effectively process these multi-material combinations. In order to accomplish these goals, the following program milestones were completed by the team: 1) Developed RSR process parameters, producing multi-material joints for mechanical testing and corrosion assessments. 2) Conducted corrosion evaluation of RSR and baseline joints assembled between automotive type aluminum alloys, steels, and carbon fiber using several corrosion mitigation strategies. 3) Developed a production ready feed system and integrate into a robotic resistance spot welding station to simulate automotive production conditions. 4) Produced demonstration assemblies for testing and evaluation.

36 MATERIALS SCIENCE↗

Laser nanostructured surface preparation for joining materials

A joined article includes a first component having a laser-treated surface portion and a second component having a laser-treated surface portion. An adhesive joins the first component to the second component at the treated surface portion. A method of making a joined article form components and a system for making joined articles are also disclosed.

Sabau, Adrian Stefan↗

Laser nanostructured surface preparation for joining materials

A joined article includes a first component having a laser-treated surface portion and a second component having a laser-treated surface portion. An adhesive joins the first component to the second component at the treated surface portion. A method of making a joined article form components and a system for making joined articles are also disclosed.

Sabau, Adrian Stefan↗

Femtosecond Laser-Induced Nano-Joining of Volatile Tellurium Nanotube Memristor

Nanowire/nanotube memristor devices provide great potential for random-access high-density resistance storage. However, fabricating high-quality and stable memristors is still challenging. This paper reports multileveled resistance states of tellurium (Te) nanotube based on the clean-room free femtosecond laser nano-joining method. The temperature for the entire fabrication process was maintained below 190 °C. A femtosecond laser joining technique was used to form nanowire memristor units with enhanced properties. Femtosecond (fs) laser-irradiated silver-tellurium nanotube-silver structures resulted in plasmonic-enhanced optical joining with minimal local thermal effects. This produced a junction between the Te nanotube and the silver film substrate with enhanced electrical contacts. Noticeable changes in memristor behavior were observed after fs laser irradiation. Capacitor-coupled multilevel memristor behavior was observed. Compared to previous metal oxide nanowire-based memristors, the reported Te nanotube memristor system displayed a nearly two-order stronger current response. The research displays that the multileveled resistance state is rewritable with a negative bias.

42 ENGINEERING↗

Two-sided friction stir riveting by extrusion: A process for joining dissimilar materials

Two-sided friction stir riveting (FSR) by extrusion is an innovative process developed to rapidly, efficiently, and securely join dissimilar materials. This process extends a previously developed one sided friction stir extrusion process to create a strong and robust joint by producing a continuous, rivet-like structure through a preformed hole in one of the materials with a simultaneous, two-sided friction stir spot weld. The two-sided FSR by extrusion process securely joins the dissimilar materials together and effectively locks them in place without the use of any separate materials or fasteners. Lastly, in this paper we demonstrate the process by joining aluminum to steel and illustrate its potential application to automotive and aerospace manufacturing processes.

36 MATERIALS SCIENCE↗