Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “isopropanol”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Production of Bioproducts from Electrochemically-Generated C1 Intermediates

The overarching objective of the project was to develop an integrated process that converts carbon dioxide (CO 2 ) into the platform chemical isopropanol (IPA) using a combination of two key technologies: CO 2 electrolysis and gas fermentation. The final goal was to demonstrate the full process at bench scale with a minimum carbon conversion efficiency of 37% and to evaluate the economics and environmental impact of scaling up the electrochemical-biochemical process.

30 DIRECT ENERGY CONVERSION↗

A 2D/3D Heterostructure Perovskite Solar Cell with a Phase‐Pure and Pristine 2D Layer

Abstract Interface engineering plays a critical role in advancing the performance of perovskite solar cells. As such, 2D/3D perovskite heterostructures are of particular interest due to their optoelectrical properties and their further potential improvements. However, for conventional solution‐processed 2D perovskites grown on an underlying 3D perovskite, the reaction stoichiometry is normally unbalanced with excess precursors. Moreover, the formed 2D perovskite is impure, leading to unfavorable energy band alignment at the interface. Here a simple method is presented that solves both issues simultaneously. The 2D formation reaction is taken first to completion, fully consuming excess PbI 2 . Then, isopropanol is utilized to remove excess organic ligands, control the 2D perovskite thickness, and obtain a phase‐pure, n = 2, 2D perovskite. The outcome is a pristine (without residual 2D precursors) and phase‐pure 2D perovskite heterostructure with improved surface passivation and charge carrier extraction compared to the conventional solution process. PSCs incorporating this treatment demonstrate a notable improvement in both stability and power conversion efficiency, with negligible hysteresis, compared to the conventional process.

14 SOLAR ENERGY↗

Solvent-Mediated Formation of Quasi-2D Dion-Jacobson Phases on 3D Perovskites for Inverted Solar Cells Over 23% Efficiency

2D-on-3D (2D/3D) perovskite heterostructures present a promising strategy to realize efficient and stable photovoltaics. However, their applicability in inverted solar cells is limited due to the quantum confinement of the 2D-layer and solvent incompatibilities that disrupt the underlying 3D layer, hampering electron transport at the 2D/3D interface. Herein, solvent-dependent formation dynamics and structural evolution of 2D/3D heterostructures are investigated via in situ X-ray scattering. In this study, it is revealed that solvent interaction with the 3D surface determines the formation sequence and spatial distribution of quasi-2D phases with n = 2–4. Isopropanol (IPA) reconstructs the perovskite into a PbI 2 -rich surface, forming a strata with smaller n first, followed by a thinner substratum of larger n. In contrast, 2,2,2-Trifluoroethanol (TFE) preserves the 3D surface, promoting the formation of uniformly distributed larger n domains first, and smaller n last. Leveraging these insights, Dion–Jacobson perovskites are used with superior charge transport properties and structural robustness to fabricate 2D/3D heterostructures dominated by n ≥ 3 and engineer a favorable energy landscape for electron tunneling. Inverted solar cells based on 3-Aminomethylpyridine and TFE achieve a champion efficiency of 23.60%, with V oc and FF of 1.19 V and 84.5%, respectively, and superior stabilities with t 94 of 960 h under thermal stress.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Room‐Temperature Formate Ester Transfer Hydrogenation Enables an Electrochemical/Thermal Organometallic Cascade for Methanol Synthesis from CO 2

Abstract The reduction of CO 2 to synthetic fuels is a valuable strategy for energy storage. However, the formation of energy‐dense liquid fuels such as methanol remains rare, particularly under low‐temperature and low‐pressure conditions that can be coupled to renewable electricity sources via electrochemistry. Here, a multicatalyst system pairing an electrocatalyst with a thermal organometallic catalyst is introduced, which enables the reduction of CO 2 to methanol at ambient temperature and pressure. The cascade methanol synthesis proceeds via CO 2 reduction to formate by electrocatalyst [Cp*Ir(bpy)Cl] + (Cp*=pentamethylcyclopentadienyl, bpy=2,2′‐bipyridine), Fischer esterification of formate to isopropyl formate catalyzed by trifluoromethanesulfonic acid (HOTf), and thermal transfer hydrogenation of isopropyl formate to methanol facilitated by the organometallic catalyst (H‐PNP)Ir(H) 3 (H‐PNP=HN(C 2 H 4 P i Pr 2 ) 2 ). The isopropanol solvent plays several crucial roles: activating formate ion as isopropyl formate, donating hydrogen for the reduction of formate ester to methanol via transfer hydrogenation, and lowering the barrier for transfer hydrogenation through hydrogen bonding interactions. In addition to reporting a method for room‐temperature reduction of challenging ester substrates, this work provides a prototype for pairing electrochemical and thermal organometallic reactions that will guide the design and development of multicatalyst cascades.

Fernández, Sergio [Department of Chemistry Univers↗

Room-Temperature Formate Ester Transfer Hydrogenation Enables an Electrochemical/Thermal Organometallic Cascade for Methanol Synthesis from CO 2

The reduction of CO 2 to synthetic fuels is a valuable strategy for energy storage. However, the formation of energy-dense liquid fuels such as methanol remains rare, particularly under low-temperature and low-pressure conditions that can be coupled to renewable electricity sources via electrochemistry. Here, in this study, a multicatalyst system pairing an electrocatalyst with a thermal organometallic catalyst is introduced, which enables the reduction of CO 2 to methanol at ambient temperature and pressure. The cascade methanol synthesis proceeds via CO 2 reduction to formate by electrocatalyst [Cp*Ir(bpy)Cl] + (Cp*=pentamethylcyclopentadienyl, bpy=2,2'-bipyridine), Fischer esterification of formate to isopropyl formate catalyzed by trifluoromethanesulfonic acid (HOTf), and thermal transfer hydrogenation of isopropyl formate to methanol facilitated by the organometallic catalyst (H-PNP)Ir(H) 3 (H-PNP=HN(C 2 H 4 P i Pr 2 ) 2 ). The isopropanol solvent plays several crucial roles: activating formate ion as isopropyl formate, donating hydrogen for the reduction of formate ester to methanol via transfer hydrogenation, and lowering the barrier for transfer hydrogenation through hydrogen bonding interactions. In addition to reporting a method for room-temperature reduction of challenging ester substrates, this work provides a prototype for pairing electrochemical and thermal organometallic reactions that will guide the design and development of multicatalyst cascades.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Facet-Dependent Water Inhibition of Alkanol Dehydration on TiO2 via Distinct Water–Alkanol Complexes

Water is ubiquitous in biomass-derived feeds, yet its molecular impact on oxygen-elimination reactions remains poorly understood, particularly for catalysts exposing different facets. Here, we utilize well-defined TiO2 nanocrystals with dominant (101) and (001) facets to reveal a pronounced facet-dependent effect of water, where inhibition for dehydration of isopropanol (IPA) on the TiO2(001) surface is about four times more severe than TiO2(101). Through a combination of in situ solid state NMR, in situ infrared spectroscopy, kinetics studies, and theoretical calculations, we demonstrate that this disparity arises from the formation of distinct alkanol-water complex intermediates. On TiO2(001), IPA undergoes dissociative adsorption to form an isopropoxide-H2O complex that readily drives the surface into a complex-dominated regime. This pathway increases the activation barrier for C–H cleavage by 40 kJ mol-1 by inducing a disordered transition state. In contrast, TiO2(101) favors molecular IPA adsorption with weak hydrogen bonding to water, resulting in a smaller complex formation constant and a much smaller activation barrier increase (25 kJ mol-1). By quantitatively linking facet-dependent complex coverage to transition-state destabilization, this work moves beyond simple site-blocking models and provides a conceptual framework for designing catalysts that remain active in water-containing environments

Hu, Wenda↗

Efficient transfer hydrodehalogenation of halophenols catalyzed by Pd supported on ceria

We report the transfer hydrodehalogenation (THD) of halophenols is efficiently catalyzed by palladium supported on high surface area ceria (Pd/CeO 2 ) under mild conditions (65 °C) using isopropanol (iPrOH) as hydrogen source. The reactivity of 4-halophenols (4-X-PhOH) varies in the order 4-F-PhOH > 4-Cl-PhOH > 4-Br-PhOH > > 4-I-PhOH and appears to be controlled by the desorption of halides from the catalyst surface. Kinetic analysis of the reactions and temperature programmed surface reaction (TPSR) experiments indicate that oxidative addition of C-X bonds and H-abstraction from isopropoxide compete for the same active sites on Pd. The catalyst was able to conduct the THD of various hazardous pollutants and emerging contaminants (dichlorodiphenyltrichloroethane (DDT), pentachlorophenol, pentafluorophenol and triclosan).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optimization and understanding of ZnO nanoarray supported Cu-ZnO-Al 2 O 3 catalyst for enhanced CO 2 -methanol conversion at low temperature and pressure

Cu-ZnO-Al 2 O 3 is the most widely applied catalyst for CO 2 hydrogenation to methanol. However, it is still a challenge to produce methanol using this catalyst under low-temperature (<250 °C) and low-pressure (<10 bar) conditions with desirable yield and selectivity. In this work, by tuning the experimental processing parameters such as solvent, loading amount, and annealing temperature, highly improved ZnO nanoarray supported Cu-ZnO-Al 2 O 3 catalysts have been successfully demonstrated. Here, by using organic solvent (N,N-dimethylformamide (DMF), acetone, or isopropanol) for dip-coating loading process instead of deionized (DI) water, Cu-ZnO-Al 2 O 3 nanocatalysts was comparatively better dispersed on the nanorod array support with populated and abundant active sites, thus enhancing the methanol yield. With the control of the loading amount and annealing temperature, finely distributed Cu nanoparticles were obtained on the ZnO nanorod surfaces to enhance the interactions between Cu and ZnO nanorod surfaces. Further improvement of the catalyst performance is demonstrated by tuning the reaction space velocity. At 200 °C and 10 bar conditions, the optimized catalyst achieved a methanol yield of 6.46 mol h –1 kg –1 with 100 % selectivity. The good stability after prolonged testing of the catalysts demonstrates the potential practical implementation. The in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) measurements under the 1 bar reveal that the CO 2 hydrogenation to methanol on the ZnO nanoarray supported Cu-ZnO-Al 2 O 3 catalyst follows the CO reaction pathway, due to the surface oxygen vacancies on ZnO nanorods which facilitate CO 2 dissociation.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Photoelectrocatalytic reduction of CO 2 to formate using immobilized molecular manganese catalysts on oxidized porous silicon

The reduction of carbon dioxide (CO 2 ) to formate using molecular catalysts immobilized on high surface area porous silicon is described. Manganese complexes of the type ( R bpy)Mn(CO) 3 Br (bpy = 2,2′-bipyridine) were prepared with silatrane groups on the bpy ligand for attachment to oxide-coated porous silicon (SiO x -porSi). SiO x -porSi wafers were formed by heating hydrogen-terminated p-type porous silicon wafers under air, and the manganese complexes were immobilized on SiO x -porSi by heating at 80°C. The resulting hybrid photoelectrodes are photoelectrocatalysts for CO 2 reduction in acetonitrile containing 2.0 M triethylamine and 2.0 M isopropanol, yielding formate with high selectivity (>96%) and current density (∼0.6 mA/cm 2 ), excellent reproducibility, and a photovoltage of 280 mV at −1.75 V (versus ferrocenium/ferrocene) under 1 sun illumination. Here, the applied potential is close to the equilibrium potential for CO 2 reduction to formate. This work presents rare examples of immobilized molecular catalysts for CO 2 reduction to formate and the first on semiconducting silicon.

13 HYDRO ENERGY↗

Combustion characteristics of diisopropoxymethane, a low-reactivity oxymethylene ether

Oxymethylene ethers (OMEs) have been studied for use as low-sooting diesel fuel additives or substitutes; very little literature discusses OMEs as spark-ignition (SI) fuels due to their typically high cetane numbers. In this work, a lower-reactivity, branched OME, diisopropoxymethane (DIPM), is evaluated to determine its effectiveness as a spark-ignition fuel, as it is the lowest-reactivity OME (as determined by Indicated Cetane Number) thus far evaluated in the literature. DIPM is synthesized in-house via acetalization from isopropanol (iPrOH) and trioxane using standard OME production practices. DIPM was then tested in a rapid compression machine (RCM) for autoignition and spark ignition characteristics, and in a modified CFR engine to determine effective octane numbers. In the RCM, an autoignition temperature sweep was performed at stoichiometric conditions from 1000/T = 1.7 - 1.0, at 5:1 inert ratio (comparable to approximately 25% EGR), where it was found that DIPM has ignition delay times 5–10x faster than isooctane and displays NTC ignition behavior. Blends with iPrOH indicate that reactivity can be matched with isooctane with low blend ratios of iPrOH in DIPM. Flame speeds were tested with a laser spark for ignition in the RCM, where the flame speed of DIPM and isooctane is determined to be comparable at engine relevant conditions. In the CFR engine, effective RON and MON based on pressure trace frequency domain measurements were determined for DIPM and a 15 vol% iPrOH in DIPM blend. Neat DIPM has (R+M)/2 = 59 and a negative sensitivity of S = -18, consistent with its NTC behavior and higher reactivity. Furthermore the DIPM/iPrOH blend has positive sensitivity and a pump-gasoline range (R+M)/2 = 89.3. DIPM on its own is unlikely to be an effective SI fuel, however, when blended with iPrOH as an ON booster, it may be a promising SI candidate fuel.

09 BIOMASS FUELS↗

Variability in structural carbohydrates, lipid composition, and cellulosic sugar production from industrial hemp varieties

The aim of this study was to determine carbohydrate recovery from hemp for ethanol production and quantify biodiesel from TAG (Triacylglycerol) present in hemp. The structural composition of five different hemp varieties (Seward County-SC, York County-YC, Loup County-LC, 19 m96136-19 m, and CBD Hemp-CBD) were analyzed. Concentration of glucan and xylan ranged between 32.63 to 44.52% and 10.62 to 15.48% respectively. The biomass was then pretreated with Liquid hot water followed by disk milling and then hydrolyzed enzymatically to yield monomeric sugars. High glucose (63-85%) and xylose (73-88%) recovery was achieved. Lipids were extracted from hemp using hexane and isopropanol and then transesterified to produce biodiesel. Approximately, 50% of total fatty acids in SC, LC, and CBD hemp were linoleic acid. Palmitic acid was present between 32 to 50% in varieties YC and 19 m. Highest TAG concentration at 25% of total lipids was observed in CBD hemp. In conclusion, the analysis on lipid composition and high sugar recovery demonstrates hemp as a potential bioenergy crop for ethanol and biodiesel coproduction.

09 BIOMASS FUELS↗

Environmental application of chlorine-doped graphitic carbon nitride: Continuous solar-driven photocatalytic production of hydrogen peroxide

Solar-driven photocatalytic generation of H 2 O 2 over metal-free catalysts is a sustainable approach for value-added chemical production. Here, we synthesized chlorine-doped graphitic carbon nitride (Cl-doped g-C 3 N 4 ) through a solvothermal method to effectively produce H 2 O 2 with a rate of 1.19 ± 0.06 µM min –1 under visible light irradiation, which was improved by 104 times compared to pristine g-C 3 N 4 . Continuous net production of H 2 O 2 was realized at a rate of 2.78 ± 0.10 µM min –1 up to 54 h with isopropanol as the hole scavenger, whereas H 2 O 2 production was only sustained for ~ 6 h without scavengers. Both molecular simulations and advanced spectroscopic characterizations elucidated that the Cl dopant increased the charge transfer rate, decreased the bandgap, and reduced the activation energy of the rate-limiting step of O 2 reduction, all of which favored H 2 O 2 production. Furthermore, this work implemented a novel metal-free photocatalyst for sustainable H 2 O 2 production and elucidated the mechanism for promoting H 2 O 2 production that can guide future photoreactive nanomaterial design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Can CO 2 -assisted alkane dehydrogenation lead to negative CO 2 emissions?

The utilization of light alkanes to generate value-added chemicals has gained significant attention due to the U.S. shale gas boom in recent decades. For example, after methane, ethane (3-16 vol.%) and propane (up to 5 vol.%) are the most abundant hydrocarbon species in shale gas deposits. Further, these inexpensive, widely available, but often underutilized, light alkanes can be used as a feedstock to produce olefins, which are among the most important petrochemical building blocks in chemical industry. Ethylene and propylene are used in the production of polymers (e.g., polyethylene, polypropylene) and epoxides (e.g., ethylene oxide, propylene oxide), as well as intermediates in the manufacture of numerous other chemicals (e.g., ethylene glycol, ethylbenzene, acetone, isopropanol, acrylonitrile).

03 NATURAL GAS↗

Open-air spray deposition of PCBM/BCP electron transport layer for inverted perovskite solar cells

A [6,6]-phenyl C61 butyric acid methyl ester (PCBM) and bathocuproine (BCP) electron transport layer (ETL) is spray deposited in open air directly on top of a perovskite at linear speeds of 9 m/min. The PCBM precursor ink contains a binary mixture of 1:1 chlorobenzene:chloroform, which optimizes spray wettability on the perovskite surface and allows quick solvent evaporation. A near-infrared heating module additionally provides a flash cure (<5 s) for the formation of smooth, large-area PCBM films (∼20 cm 2 ). A BCP solution in isopropanol is subsequently sprayed to form an ultrathin (<5 nm) film and characterized with a suite of high-resolution metrologies. The spray-deposition processing and near-infrared treatment do not damage the underlying perovskite. Inverted architecture devices containing the sprayed ETL achieve a champion efficiency of 20.3% and demonstrate stable performance without additional interlayers or surface treatments. Here, the technoeconomic cost of the open-air spray process is compared against traditional vacuum-based evaporation, resulting in a decrease in manufacturing costs by 26%.

14 SOLAR ENERGY↗

An improved detailed chemical kinetic model for C3-C4 linear and iso-alcohols and their blends with gasoline at engine-relevant conditions

Propanol and butanol isomers have received significant research attention as promising fuel additives or neat biofuels. Robust chemical kinetic models are needed that can provide accurate and efficient predictions of combustion performance across a wide range of engine relevant conditions. Herein, this study seeks to improve the understanding of ignition and combustion behavior of pure C3-C4 linear and iso-alcohols, and their blends with gasoline at engine-relevant conditions. In this work, a kinetic model with improved thermochemistry and reaction kinetics was developed based on recent theoretical calculations of H-atom abstraction and peroxy radical reaction rates. Kinetic model validations are reported, and the current model reproduces the ignition delay times of the C3 and C4 alcohols well. Variations in reactivity over a wide range of temperatures and other operating conditions are also well predicted by the current model. Recent ignition delay time measurements from a rapid compression machine of neat iso-propanol and iso-butanol [Cheng et al., Proc. Combust Inst. (2020)] and blends with a research grade gasoline [Goldsborough et al., Proc. Combust Inst. (2020)] at elevated pressure (20–40 bar) and intermediate temperatures (780–950 K) were used to demonstrate the accuracy of the current kinetic model at conditions relevant to boosted spark-ignition engines. The effects of alcohol blending with gasoline on the autoignition behavior are discussed. The current model captures the suppression of reactivity in the low-temperature and negative-temperature-coefficient (NTC) region when either isopropanol and isobutanol are added to a research grade gasoline. Sensitivity and reaction flux analysis were performed to provide insights into the relevant fuel chemistry of the C3-C4 alcohols.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Reconfigurable structural color by reversible switching of colloidal discoid liquid crystal alignment

Combining the effects of alternating-current (AC) electric fields and sedimentation reconfigures colloidal discoids between planar and homeotropic orientational alignments, thereby controlling the material’s structural color. Here, we self-assemble micrometer-size polystyrene discoids in an isopropanol-water mixture. After sedimentation, the discoids adopt a homeotropic alignment, with the minor axis perpendicular to the substrate. Adding an AC electric field (1 kHz) of ≥0.50 V switches the discoids to planar alignment—with the minor axis parallel to the substrate—within ∼100 s. Removing the field switches them back to homeotropic alignment within ∼300 s. Kinetic modeling of the field-induced torques yields good agreement with these measurements. The peak wavelength and intensity of the crystal’s diffraction response shift significantly upon reconfiguration; scattering simulation predicts these shifts. The reconfiguration is maintained for at least 10 cycles. This method is a simple, scalable avenue to reconfigure the optical properties of colloidal crystals produced from simple dielectric spheroids.

colloidal crystals↗

A Rhenium Bis -tetramethylphenanthroline Catalyst for CO 2 Reduction to Formate

Catalytic CO 2 reduction reactions featuring high selectivity toward formate are relatively rare. In some homogeneous molecular CO 2 -reducing electrocatalysis, using triethylamine (TEA) and isopropanol (IPA) as additives improves catalytic performance in producing formate. In this paper, we investigate whether the rhenium(I) bis-diimine dicarbonyl complexes, cis-[Re(N^N) 2 (CO) 2 ] + , where N^N is 2,2’-bipyridine ([1] + ) or 3,4,7,8-tetramethyl-1,10-phenanthroline ([2] + ), are capable of electrocatalytically reducing CO 2 to formate in acetonitrile containing TEA and IPA. Catalyst [1] + was ineffective at CO 2 reduction, yielding formate quantities comparable to those produced in experiments without the catalyst. Catalyst [2] + , however, is a promising electrocatalyst for the CO 2 reduction reaction in the presence of TEA and IPA, with formate being produced in millimolar concentrations (10.5 mM), as detected by 1 H NMR spectroscopy after 6 h electrolysis (formate Faradaic efficiency = 11%, with the major balance going to H 2 ). Upon more detailed examination, [2] + exhibited a turnover frequency (TOF) of 12 s –1 for formate, comparable to other leading molecular catalysts that competently execute this reduction. Combinations of spectroscopy, electrochemistry, and theory were used to better understand the mechanism of CO 2 reduction by [2] + . Fourier transform infrared spectroelectrochemical (FTIR-SEC) data provided no evidence for CO ligand dissociation or substitution upon one- and two-electron reduction of [2] + , suggesting that a mechanism distinct from one that is metal-hydride-based is operative in catalysis. Computational studies guide mechanistic investigations toward the proposed formation of a hydrophenanthroline-based intermediate responsible for hydride transfer to CO 2 and electrocatalytic formate production from [2] + .

Beverages↗

Chemical Diversity of Oligomers in Biomass Fast Pyrolysis Oils, Part 2: Heavy Lignin-Derived Molecules and Highly Dehydrated Sugars from Dichloromethane-Insoluble Pyrolytic Lignin

Here, this paper, the second in a series, investigates the water-insoluble, dichloromethane (DCM)-insoluble residue of BTG pyrolysis oil, also known in the literature as high-molecular-weight pyrolytic lignin (HMW-PL). HMW-PL accounts for 9.2 wt % of the original bio-oil, which is known to increase upon aging and contribute to coke formation during bio-oil upgrading. Understanding its composition is crucial for managing pyrolysis oil during the processing. The HMW-PL was fractionated using a silica gel column with solvents of increasing polarity: ethyl acetate (EA), acetone (AC), isopropanol (ISO), and methanol (MeOH), yielding 49.2, 19.9, 8.2, and 8.1 wt %, respectively. Each subfraction was characterized by UV-fluorescence, FTIR, HSQC NMR, and (−)APCI-FT-Orbitrap MS. Analysis revealed that the EA subfraction primarily contained aromatic dimers (C 19 –C 20 ) and trimers (C 17 –C 13 ), while the MeOH subfraction was rich in oxygenated aliphatic monomers (C 8 –C 16 ) likely derived from sugar dehydration products. The resulting fractions were further separated via preparatory HPLC. Fifty-five candidate molecular structures were proposed based on the Orbitrap MS data, supported by UV-fluorescence, FTIR, and NMR results. This fractionation strategy defined four distinct subfractions, enabling the proposal of surrogate molecular structures and advancing the molecular-level understanding of the HMW-PL fraction in the pyrolysis bio-oil.

High-Molecular-Weight PL↗