Results for “instability” — Page 3

NASA NTRS2022

Nonlinear Evolution of Instabilities in a Laminar Separation Bubble at a Hypersonic Mach Number

The development of both convective stationary perturbation as well as global instabilities in the vicinity of a laminar separation bubble above an axisymmetric compression corner in a hypersonic flow is investigated using numerical simulations. The flow configuration of primary interest corresponds to the cone-cylinder-flare model used in experimental measurements in the Boeing/AFOSR Mach-6 Quiet Tunnel at Purdue University. For a flare angle of 10 degrees and a unit Reynolds number of 11.5 x 10 6 m -1 , their surface flow visualizations identified the presence of streamwise elongated thermal streaks near the reattachment position and the dominant azimuthal spacing between the streaks was determined to be approximately 10 degrees (i.e., an azimuthal mode number of 36). Previous linear stability analyses predicted that the amplification characteristics of small amplitude, unsteady, convective instabilities within this flow were consistent with the surface pressure fluctuations measured in the experiment. However, their accompanying analysis of global instabilities had found the separation bubble to be weakly unstable at the 10 degrees flare angle, with the most unstable global mode corresponding to a stationary disturbance with an azimuthal wavenumber of m ≈ 5, which was well below the measured wavenumber of m = 36. Besides confirming the presence of the global instability at these flow conditions, the present numerical simulations quantify the details of the stationary equilibrium state associated with the supercritical bifurcation resulting from the nonlinear saturation of the unstable global mode. Although velocity perturbations associated with the saturated global mode are dominated by the fundamental spanwise wavelength associated with the linear global instability, the surface heat flux downstream of reattachment is dominated by m = 36 in agreement with experimental measurements. However, the shorter wavelength peak ( m = 36) in the azimuthal spectrum is not manifested as streaks with an azimuthal spacing of 10 degrees. An additional simulation of the combined evolution of both unsteady convective and global instabilities indicates that the nonlinear interactions between a broadband spectrum of oblique Mack’s first mode instabilities generate stationary vortex modes with a higher dominant wavenumber ( m = 60) as that observed in the experiments. Additional analyses are performed to predict the global mode behavior at other flare angles and how it differs from the convective centrifugal instability due to concave streamline curvature over the compression corner.

Hypersonic flow↗

NASA NTRS2022

Nonlinear Evolution of Instability in a Laminar Separation Bubble at Hypersonic Mach Number

The development of both convective stationary perturbation as well as global instabilities in the vicinity of a laminar separation bubble above an axisymmetric compression corner in a hypersonic flow is investigated using numerical simulations. The flow configuration of primary interest corresponds to the cone-cylinder-flare model used in experimental measurements in the Boeing/AFOSR Mach-6 Quiet Tunnel at Purdue University. For a flare angle of 10 degrees and a unit Reynolds number of 11.5 x 10 6 m -1 , their surface flow visualizations identified the presence of streamwise elongated thermal streaks near the reattachment position and the dominant azimuthal spacing between the streaks was determined to be approximately 10 degrees (i.e., an azimuthal mode number of 36). Previous linear stability analyses predicted that the amplification characteristics of small amplitude, unsteady, convective instabilities within this flow were consistent with the surface pressure fluctuations measured in the experiment. However, their accompanying analysis of global instabilities had found the separation bubble to be weakly unstable at the 10 degrees flare angle, with the most unstable global mode corresponding to a stationary disturbance with an azimuthal wavenumber of m ≈ 5, which was well below the measured wavenumber of m = 36. Besides confirming the presence of the global instability at these flow conditions, the present numerical simulations quantify the details of the stationary equilibrium state associated with the supercritical bifurcation resulting from the nonlinear saturation of the unstable global mode. Although velocity perturbations associated with the saturated global mode are dominated by the fundamental spanwise wavelength associated with the linear global instability, the surface heat flux downstream of reattachment is dominated by m = 36 in agreement with experimental measurements. However, the shorter wavelength peak ( m = 36) in the azimuthal spectrum is not manifested as streaks with an azimuthal spacing of 10 degrees. An additional simulation of the combined evolution of both unsteady convective and global instabilities indicates that the nonlinear interactions between a broadband spectrum of oblique Mack’s first mode instabilities generate stationary vortex modes with a higher dominant wavenumber ( m = 60) as that observed in the experiments. Additional analyses are performed to predict the global mode behavior at other flare angles and how it differs from the convective centrifugal instability due to concave streamline curvature over the compression corner.

High speed flow↗

NASA NTRS1976

Temperature anisotropy and beam type whistler instabilities

Whistler instabilities have been investigated for two different types; i.e., a temperature-anisotropy type instability and a beam-type instability. A comparison between the two types of whistler instabilities is made within the framework of linear theory. A transition from one type to the other is also discussed, which is an extension of the work on electrostatic beam and Landau instabilities performed by O'Neil and Malmberg (1968) for electromagnetic whistler instabilities. It is clarified that the essential source of the whistler instability is not beam kinetic energy but a temperature anisotropy, even for the beam-type whistler instability.

Hashimoto, K.↗

NASA NTRS1993

Nonlinear evolution of electromagnetic ion beam instabilities

A comparative study of the ion/ion right-hand resonant instability and the ion/ion nonresonant instability is carried out to investigate and contrast their properties. Linear analysis demonstrates that the nonresonant instability becomes resonant if the density of the ion beam is sufficiently high. Hybrid simulations show that both the resonant and nonresonant instabilities result in the formation of nonlinear pulses, called pulsations, but with distinct features. For example, the pulsations generated by the resonant instability have a positive correlation with the ion density, while those generated by the nonresonant instability are likely to have a relatively weak negative correlation. The waves generated by the nonresonant instability are subject to a parametric decay instability and tend to form a state of condensate where the turbulence becomes nearly monochromatic.

Akimoto, K.↗

NASA NTRS1993

Instability of rectangular jets

The instability of rectangular jets is investigated using a vortex-sheet model. It is shown that such jets support four linearly independent families of instability waves. Within each family there are infinitely many modes. A way to classify these modes according to the characteristics of their mode shapes or eigenfunctions is proposed. It is demonstrated that the boundary element method can be used to calculate the dispersion relations and eigenfunctions of these instability wave modes. The method is robust and efficient. A parametric study of the instability wave characteristics has been carried out. A sample of the numerical results is reported here. It is found that the first and third modes of each instability wave family are corner modes. The pressure fluctuations associated with these instability waves are localized near the corners of the jet. The second mode, however, is a center mode with maximum fluctuations concentrated in the central portion of the jet flow. The center mode has the largest spatial growth rate. It is anticipated that as the instability waves propagate downstream the center mode would emerge as the dominant instability of the jet.

Tam, Christopher K. W.↗

NASA NTRS1993

Spatial simulation of secondary instability in plane channel flow - Comparison of K- and H-type disturbances

This study involves a numerical simulation of spatially evolving secondary instability in plane channel flow. The computational algorithm integrates the time-dependent, 3D, incompressible Navier-Stokes equations by a mixed finite-difference/spectral technique. In particular, we are interested in the differences between instabilities instigated by Klebanoff (K-) type and Herbert (H-) type inflow conditions, and in comparing the present spatial results with previous temporal models. It is found that for the present inflow conditions, H-type instability is biased towards one of the channel walls, while K-type instability evolves on both walls. For low initial perturbation amplitudes, H-type instability exhibits higher growth rates than K-type instability, while higher initial amplitudes lead to comparable growth rates of both H- and K-type instability. In H-type instability, spectral analysis reveals the presence of the subharmonic 2D mode which promotes the growth of the 3D spanwise and fundamental modes through nonlinear interactions. An intermodal energy transfer study demonstrates that there is a net energy transfer from the 3D modes to the 2D mode. This analysis also indicates that the mean mode transfers net energy to the 2D subharmonic mode and to the 3D modes.

Saiki, E. M.↗

NASA NTRS1994

Beat, modulational, and decay instabilities of a circularly polarized Alfven wave

A circulary polarized low-frequency electomagnetic pump wave propoagating along an ambient magnetic field is known to be unstable to the growth of several parallel-propagating parametric instabilties. If ion-cyclotron effects are retained in a two-fluid description, the dispersion relation is a sixth-order polynomial. We present a series of new analytical approximations to this dispersion relation. We emphasize new results for the beat instability that occurs as an interaction of the forward prpagating upper sideband with the backward propagating lower sideband. The nature of the beat instabitlity depends on beta = (v(sub sound)/v(sub A)(exp 2) and on the sense of polarization of the pump wave. The beat and decay instabilities can occur together if the pump is left-handed (i.e., ion resonant) and if beta is less than or approximately 1, but they cannot occur together if the pump is right-handed. For a left-handed pump the beat mode is the only instability if beta is greater than or approximately 1. If the pump is right-handed and beta is greater than or approximately 1, then the beat instability exists only when the pump amplitude exceeds a threshold value, and the beat will be the only instability if the pump amplitude is large enough to stabilize the modulational instability. If the pump is left-handed and beta is less than or approximately 1, then the beat mode is stabilized when the pump amplitude becomes sufficiently large. The beat instability primarily produces a forward propagating transverse wave in the upper sideband. Thus if beta is greater than or approximately 1, the instabilities considered here do not produce the backward propagating waves which are thought to affect turbulence and the evolution of cross helicity in the solar wind. New analytical results are presented also for the decay and modulational instabilites when beta is approximately equal to 1.

Hollweg, Joseph V.↗

NASA NTRS1995

Nonaxisymmetric secular instabilities driven by star/disk coupling

We determine conditions for the onset of nonaxisymmetric secular instabilities in polytropes with a wide range of angular momentum distributions using Lagrangian techniques, and then calculate the growth rate of such instabilities when driven by the coupling of the perturbed star to a circumstellar disk. We use Langrangian displacement vectors with azimuthal dependence proportional to exp (im phi), where m is an integer and phi is the azimuthal coordinate. The onset of secular instability in terms of the quantity T/absolute value of W, the ratio of rotational kinetic energy to gravitational potential energy, is affected by both the compressibility and the angular momentum distribution of the polytrope. The largest effects occur when the angular momentum distribution is varied. For polytropic index n = 3/2, the onset of secular instability for the m = 2 mode (the bar mode), as determined by its neutral point, shifts from T/absolute value of W = 0.141 to 0.093, while the m = 5 mode neutral point shifts from T/absolute value of W = 0.088 to 0.031 over the range of angular momentum distributions we consider. The smallest critical T/absolute value of W-values occur for the angular momentum distributions which are the most peaked toward the equator. For the angular momentum distribution of a Maclaurin spheroid, as the polytropic index n is increased from 3/2 to 5/2, the neutral point for m = 2 shifts from T/absolute value of W = 0.141 to 0.144 and the netural point for m = 5 shifts from T/absolute value of W = 0.069 to 0.078. The netural points for m = 2 and 5 for the Maclaurin sequence (n = 0) are 0.137 and 0.0629, respectively. As the angular momentum distribution becomes more peaked toward the equatorial radius of the polytropes, the critical T/absolute value of W-values generally become less sensitive to the compressibility of the polytrope. Star/disk coupling can drive the secular instability in systems where the star is surrounded by a massive disk and, if the instability can grow to moderate amplitude, then the coupling can transport significant amounts of angular momentum from the star into the circumstellar disk. We find, for the particular case of rotating protostars during the accretion phase, that the instability growth time can be shorter than the accretion time. Further, if the instability can grow to amplitudes on the order of several percent, the star/disk coupling can remove angular momentum from the forming star faster than it is added by accretion.

Imamura, James, N.↗

NASA NTRS1999

Hydrodynamic Instability and Thermal Coupling in a Dynamic Model of Liquid-Propellant Combustion

For liquid-propellant combustion, the Landau/Levich hydrodynamic models have been combined and extended to account for a dynamic dependence of the burning rate on the local pressure and temperature fields. Analysis of these extended models is greatly facilitated by exploiting the realistic smallness of the gas-to-liquid density ratio rho. Neglecting thermal coupling effects, an asymptotic expression was then derived for the cellular stability boundary A(sub p)(k) where A(sub p) is the pressure sensitivity of the burning rate and k is the disturbance wavenumber. The results explicitly indicate the stabilizing effects of gravity on long-wave disturbances, and those of viscosity and surface tension on short-wave perturbations, and the instability associated with intermediate wavenumbers for critical negative values of A(sub p). In the limit of weak gravity, hydrodynamic instability in liquid-propellant combustion becomes a long-wave, instability phenomenon, whereas at normal gravity, this instability is first manifested through O(1) wavenumbers. In addition, surface tension and viscosity (both liquid and gas) each produce comparable effects in the large-wavenumber regime, thereby providing important modifications to the previous analyses in which one or more of these effects was neglected. For A(sub p)= O, the Landau/Levich results are recovered in appropriate limiting cases, although this typically corresponds to a hydrodynamically unstable parameter regime for p << 1. In addition to the classical cellular form of hydrodynamic stability, there exists a pulsating form corresponding to the loss of stability of steady, planar burning to time-dependent perturbations. This occurs for negative values of the parameter A(sub p), and is thus absent from the original Landau/Levich models. In the extended model, however, there exists a stable band of negative pressure sensitivities bounded above by the Landau type of instability, and below by this pulsating form of hydrodynamic instability. Indeed, nonsteady modes of combustion have been observed at low pressures in hydroxylammonium nitrate (HAN)-based liquid propellants, which often exhibit negative pressure sensitivities. While nonsteady combustion may correspond to secondary and higher-order bifurcations above the cellular boundary, it may also be a manifestation of this pulsating type of hydrodynamic instability. In the present work, a nonzero temperature sensitivity is incorporated into our previous asymptotic analyses. This entails a coupling of the energy equation to the previous purely hydrodynamic problem, and leads to a significant modification of the pulsating boundary such that, for sufficiently large values of the temperature-sensitivity parameter, liquid-propellant combustion can become intrinsically unstable to this alternative form of hydrodynamic instability. For simplicity, further attention is confined here to the inviscid version of the problem since, despite the fact that viscous and surface-tension effects are comparable, the qualitative nature of the cellular boundary remains preserved in the zero-viscosity limit, as does the existence of the pulsating boundary. The mathematical model adopts the classical assumption that there is no distributed reaction in either the liquid or gas phases, but now the reaction sheet, representing either a pyrolysis reaction or an exothermic decomposition at the liquid/gas interface, is assumed to depend on local conditions there.

Margolis, S. B.↗

NASA NTRS2003

The TP53 dependence of radiation-induced chromosome instability in human lymphoblastoid cells

The dose and TP53 dependence for the induction of chromosome instability were examined in cells of three human lymphoblastoid cell lines derived from WIL2 cells: TK6, a TP53-normal cell line, NH32, a TP53-knockout created from TK6, and WTK1, a WIL2-derived cell line that spontaneously developed a TP53 mutation. Cells of each cell line were exposed to (137)Cs gamma rays, and then surviving clones were isolated and expanded in culture for approximately 35 generations before the frequency and characteristics of the instability were analyzed. The presence of dicentric chromosomes, formed by end-to-end fusions, served as a marker of chromosomal instability. Unexposed TK6 cells had low levels of chromosomal instability (0.002 +/- 0.001 dicentrics/cell). Exposure of TK6 cells to doses as low as 5 cGy gamma rays increased chromosome instability levels nearly 10-fold to 0.019 +/- 0.008 dicentrics/cell. There was no further increase in instability levels beyond 5 cGy. In contrast to TK6 cells, unexposed cultures of WTK1 and NH32 cells had much higher levels of chromosome instability of 0.034 +/- 0.007 and 0.041 +/- 0.009, respectively, but showed little if any effect of radiation on levels of chromosome instability. The results suggest that radiation exposure alters the normal TP53-dependent cell cycle checkpoint controls that recognize alterations in telomere structure and activate apoptosis.

Non-NASA Center↗

NASA NTRS1999

Critical target and dose and dose-rate responses for the induction of chromosomal instability by ionizing radiation

To investigate the critical target, dose response and dose-rate response for the induction of chromosomal instability by ionizing radiation, bromodeoxyuridine (BrdU)-substituted and unsubstituted GM10115 cells were exposed to a range of doses (0.1-10 Gy) and different dose rates (0.092-17.45 Gy min(-1)). The status of chromosomal stability was determined by fluorescence in situ hybridization approximately 20 generations after irradiation in clonal populations derived from single progenitor cells surviving acute exposure. Overall, nearly 700 individual clones representing over 140,000 metaphases were analyzed. In cells unsubstituted with BrdU, a dose response was found, where the probability of observing delayed chromosomal instability in any given clone was 3% per gray of X rays. For cells substituted with 25-66% BrdU, however, a dose response was observed only at low doses (<1.0 Gy); at higher doses (>1.0 Gy), the incidence of chromosomal instability leveled off. There was an increase in the frequency and complexity of chromosomal instability per unit dose compared to cells unsubstituted with BrdU. The frequency of chromosomal instability appeared to saturate around approximately 30%, an effect which occurred at much lower doses in the presence of BrdU. Changing the gamma-ray dose rate by a factor of 190 (0.092 to 17.45 Gy min(-1)) produced no significant differences in the frequency of chromosomal instability. The enhancement of chromosomal instability promoted by the presence of the BrdU argues that DNA comprises at least one of the critical targets important for the induction of this end point of genomic instability.

NASA Discipline Radiation Health↗

NASA NTRS2011

Analyses of Injection-Coupled Combustion Instability from J-2X Gas Generator Development

During development of the gas generator for the liquid oxygen/liquid hydrogen propellant J-2X rocket engine, combustion instabilities were observed near the frequency of the first longitudinal acoustic mode of the hot gas combustion chamber duct. These instabilities were similar to intermediate-frequency or buzz-type instabilities as described in historical programs, except for several aspects: 1) the frequencies were low, in the realm of chug; 2) at times the instability oscillation amplitudes were quite large, with peak-to-peak amplitudes exceeding 50% of the mean chamber pressure along with the appearance of harmonics; 3) the chamber excitation was related to but not exactly at the first longitudinal combustion chamber acoustic mode; and 4) the injector provided mass flow rate oscillations induced by capacitance and inertance effects in the injector rather than by organ pipe resonances of the coaxial oxidizer posts. This type of combustion instability is referred to as "injection coupling" because one critical driving source of the instability is mass flow rate oscillations from the injector. However, the type of injection coupling observed here is different than observed in previous instances of buzz instability with coaxial injectors, because of the lower frequencies and lack of influence from the oxidizer post organ pipe resonances. Test data and preliminary analyses of the initial combustion instabilities were presented in several papers at the 5th Liquid Propulsion Subcommittee meeting. Since that time, additional hot-fire tests with several new hardware configurations have been conducted, and additional analyses have been completed. The analytical models described in previous papers have been updated to include the influences of new geometrical configurations, including a different oxidizer injector manifold configuration and a branch pipe in the hot gas duct that supplies gaseous helium during the start transient to pre-spin the turbine. In addition, the analysis methodology has been revisited to evaluate the potential influence of a combustion response as well as an injection response.

Hulka, James R.↗

NASA NTRS2020

Streak Instability Analysis for BOLT Configuration

The BOLT configuration designed for an upcoming flight experiment exemplifies the complexities of hypersonic boundary layer transition in the presence of multiple and potentially interacting instability mechanisms. A numerical study of the boundary layer instabilities over this configuration has been performed with the goal of applying state-of-the-art tools in multidimensional stability analysis that complement the other ongoing research related to the BOLT flight campaign. Specifically, the paper outlines modal instability characteristics of the boundary layer streaks adjacent to the minor-axis symmetry plane of a 1/3 rd scale BOLT configuration that was tested in the low-disturbance hypersonic wind tunnel at Purdue University and both quiet and conventional tunnels at Texas A&M University (TAMU). The basic state computations agree well with the heat flux measurements in the Purdue quiet tunnel as well as with the off-body velocity field described in a previous DNS study at the University of Minnesota. The encouraging agreement between the predicted frequency spectra of the streak instability in the region of increased boundary layer thickness and the surface pressure spectra measured during the TAMU experiments suggests that these streak instabilities may play an important role during the transition process near the symmetry plane. The modest value of the predicted peak N-factor (N max ≈ 5) for the streak instabilities provides a potential explanation for why transition is not observed under quiet flow conditions, but may occur in a noisy wind tunnel. Similar instability analyses are performed for the flight configuration at two selected flow conditions from the ascent portion of the planned flight trajectory. The predicted values of the peak N-factor suggest that transition onset in the vicinity of the center plane is possible at the ascent time of t = 26.98 seconds (N max ≈ 12.5 at X/L = 0.77), but the streak instabilities weaken sufficiently at the later time of t = 28.88 seconds (N max ≈ 11.5 at X/L ≈ 1.00) and are less likely to cause transition at that time.

Laminar turbulent transition↗

NASA NTRS2016

Mixing the Solar Wind Proton and Electron Scales: Effects of Electron Temperature Anisotropy on the Oblique Proton Firehose Instability

The double adiabatic expansion of the nearly collisionless solar wind plasma creates conditions for the firehose instability to develop and efficiently prevent the further increase of the plasma temperature in the direction parallel to the interplanetary magnetic field. The conditions imposed by the firehose instability have been extensively studied using idealized approaches that ignore the mutual effects of electrons and protons. Recently, more realistic approaches have been proposed that take into account the interplay between electrons and protons, unveiling new regimes of the parallel oscillatory modes. However, for oblique wave propagation the instability develops distinct branches that grow much faster and may therefore be more efficient than the parallel firehose instability in constraining the temperature anisotropy of the plasma particles. This paper reports for the first time on the effects of electron plasma properties on the oblique proton firehose (PFH) instability and provides a comprehensive vision of the entire unstable wave-vector spectrum, unifying the proton and the smaller electron scales. The plasma β and temperature anisotropy regimes considered here are specific for the solar wind and magnetospheric conditions, and enable the electrons and protons to interact via the excited electromagnetic fluctuations. For the selected parameters, simultaneous electron and PFH instabilities can be observed with a dispersion spectrum of the electron firehose (EFH) extending toward the proton scales. Growth rates of the PFH instability are markedly boosted by the anisotropic electrons, especially in the oblique direction where the EFH growth rates are orders of magnitude higher.

plasmas↗

NASA NTRS2021

A Computational Analysis of Boundary Layer Instability over the BOLT Configuration

The complex boundary layer flow over the BOLT flight configuration is known to exhibit multiple and potentially interacting instability mechanisms. This paper represents a continuation of our numerical investigation of the flow instabilities over the main test surface of the BOLT configuration by using state-of-the-art tools in multidimensional instability analysis. Specifically, the paper extends our previous computations by considering the separate effects of a nonzero angle of attack and a nonzero yaw on the modal instability characteristics of the boundary layer streaks adjacent to the minor-axis symmetry plane, specifically near both ends of the azimuthal region of a thick boundary layer in the middle, where this region rapidly changes to a thinner boundary layer on either side. At the t = 28.8767 s condition from the ascent part of the anticipated flight trajectory with a flight Mach number of M ∞ = 5.53 and unit Reynolds number of 4.25 x 10 6 /m, either type of departure from the design condition is shown to have a considerable impact on the structure of the basic state rollup within the region of interest and, hence, also on the amplification characteristics of instability waves within the resulting streaks. Yet, for a yaw angle of β = 4 degrees, the computations indicate only a slight reduction with respect to the peak N-factor of nearly 11 at the design condition of zero degrees yaw and zero degrees angle of attack. In contrast, an angle of attack equal to α = 4 degrees, the peak N-factor decreases to nearly 6 on the leeward side and increases above 16 on the windward side, making the onset of transition highly likely on the windward side. Computations also highlight the role of streak instabilities that originate as Mack mode disturbances and also demonstrate the potential pitfalls in using surface pressure sensors alone to gauge the magnitude of instability amplification.

Boundary layer transition↗

NASA NTRS2021

A Computational Analysis of Boundary Layer Instability over the BOLT Configuration (Effect of Nonzero AoA and Yaw)

The complex boundary layer flow over the BOLT flight configuration is known to exhibit multiple and potentially interacting instability mechanisms. This paper represents a continuation of our numerical investigation of the flow instabilities over the main test surface of the BOLT configuration by using state-of-the-art tools in multidimensional instability analysis. Specifically, the paper extends our previous computations by considering the separate effects of a nonzero angle of attack and a nonzero yaw on the modal instability characteristics of the boundary layer streaks adjacent to the minor-axis symmetry plane, specifically near both ends of the azimuthal region of a thick boundary layer in the middle, where this region rapidly changes to a thinner boundary layer on either side. At the t = 28.8767 s condition from the ascent part of the anticipated flight trajectory with a flight Mach number of M ∞ = 5.53 and unit Reynolds number of 4.25 x 10 6 /m, either type of departure from the design condition is shown to have a considerable impact on the structure of the basic state rollup within the region of interest and, hence, also on the amplification characteristics of instability waves within the resulting streaks. Yet, for a yaw angle of β = 4 degrees, the computations indicate only a slight reduction with respect to the peak N-factor of nearly 11 at the design condition of zero degrees yaw and zero degrees angle of attack. In contrast, an angle of attack equal to α = 4 degrees, the peak N-factor decreases to nearly 6 on the leeward side and increases above 16 on the windward side, making the onset of transition highly likely on the windward side. Computations also highlight the role of streak instabilities that originate as Mack mode disturbances and also demonstrate the potential pitfalls in using surface pressure sensors alone to gauge the magnitude of instability amplification.

Boundary layer transition↗

NASA NTRS1981

Effect of gravity on coupled convective and interfacial instabilities during directional solidification

Instabilities occurring during the directional constant-rate solidification of a dilute solution of tin in lead are investigated as a function of gravity with particular emphasis on small constant gravitational accelerations. Two types of instabilities have been identified: (1) convective type that corresponds to long wavelengths, and (2) morphological type that corresponds to short wavelengths. These instabilities are coupled but while the convective instabilities depend strongly on gravity, the morphological instabilities are practically independent of gravity. For low velocities, the convective instabilities occur at much lower solute concentrations than the morphological instabilities, whereas at high velocities the reverse is true.

Coriell, S. R.↗

NASA NTRS1984

Radiative tearing - Magnetic reconnection on a fast thermal-instability time scale

Two energy modification mechanisms which are known to occur in sheared magnetic fields are the tearing and thermal instabilities. These processes can be studied separately with formalisms incorporating just the effective driving mechanism of interest (finite resistivity for the tearing mode and unstable radiation for the thermal mode). A model which includes both effects, and a temperature-dependent resistivity, indicates that modified forms of these two instabilities may coexist for identical physical conditions. When they are isolated computationally, one can show that their limiting growth rates are approximately those of the uncoupled instabilities. The spatial structure and energy content of these two new hybrid processes are then individually examined and are found to differ considerably from those obtained from separate treatments of the driving mechanisms. The faster radiative instability, which has a hydromagnetically scaled growth rate like the condensation mode of the thermal instability, is shown to involve a substantial amount of magnetic field reconnection. This can be partially explained by a large temperature drop (or resistivity rise) at the X-point. The island width of the Coulomb-coupled radiative mode is 30 percent of that produced by a comparable level of the slower tearing instability. In addition, the perturbed magnetic energy in the radiative instability is 5 times that of the perturbed thermal energy, indicating an appreciable modification of the initial magnetic structure.

Steinolfson, R. S.↗