Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “inner layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Isothermal and Cyclic Oxidation of Haynes 282 Processed by Electron Beam Melting (EBM) and Laser Powder Bed Fusion (LPBF) in Dry Air at 800 and 950°C

Here, the isothermal and cyclic oxidation behavior of Haynes 282 (H282) processed by laser powder bed fusion and electron beam melting was compared to its cast counterpart during exposures in air at 800 and 950°C. The specific microstructure of the AM alloys compared to coarse-grain cast 282 resulted in differences in oxidation rates, internal oxidation and spallation behavior. At 800°C, faster Ti diffusion to the surface due to the smaller grain size of the AM alloys led to Ti doping of the Cr 2 O 3 scale and faster oxidation rates. The higher density of grain boundaries also resulted in more pronounced internal oxidation. At 950°C, a duplex Cr 2 O 3 scale was observed with a dense inner layer and porous cracked outer layer with embedded TiO 2 particles. The impact of the external and internal oxide compositions and oxidation-induced elemental depletions on the oxidation lifetime, creep properties and spallation behavior is discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Electrochemical stability, physical, and electronic properties of thermally pre-formed oxide compared to artificially sputtered oxide on Fe thin films in aqueous chloride

Here the electrochemical stability and corrosion behavior of the thermally pre-oxidized and sputter deposited variant of an oxide single-crystalline Fe thin film were compared. Thermal oxides formed Fe 2 O 3 over an inner layer of Fe 3 O 4 while the sputtered oxides were found to have grown Fe 3 O 4 instead of the target stoichiometry of Fe 2 O 3 . Oxide films of both types were stable in pH=9.3 borate buffer solution, however, were altered in pH=9.3, 0.1 M NaCl solution in the case of thermally pre-oxidized Fe thin film. The stability of the oxide differed in pH=4, 0.1 M NaCl where sputtered Fe films were more stable against acidic chemical dissolution than the thermally formed Fe oxide film. These differences were traced by AC/DC electrochemical analysis including electronic defect densities, and molecular identity characterized by ex-situ X-ray photoelectron spectroscopy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Design and evaluation of large area strip sensor prototypes for the ATLAS Inner Tracker detector

The ATLAS community is facing the last stages prior to the production of the upgraded silicon strip Inner Tracker for the High-Luminosity Large Hadron Collider. An extensive Market Survey was carried out in order to evaluate the capability of different foundries to fabricate large area silicon strip sensors, satisfying the ATLAS specifications. The semiconductor manufacturing company, Infineon Technologies AG, was one of the two foundries, along with Hamamatsu Photonics K.K., that reached the last stage of the evaluation for the production of the new devices. The full prototype wafer layout for the participation of Infineon, called ATLAS17LS-IFX, was designed using a newly developed Python-based Automatic Layout Generation Tool, able to rapidly design sensors with different characteristics and dimensions based on a few geometrical and technological input parameters. Here we present the layout design process and the results obtained from the evaluation of the new Infineon large area sensors before and after proton and neutron irradiations, up to fluences expected in the inner layers of the future ATLAS detector.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Fragmentation of photovoltaic backsheets after accelerated weathering exposure

The backsheet of a photovoltaic (PV) module functions primarily to provide safe operation through electrical insulation and protect the interior from environmental exposure. For most applications, backsheets consist of opaque, but highly reflective, films that protect inner layers from degradation from ultraviolet (UV) light. Backsheets can fail if they delaminate or form cracks under strain. In a PV module, the maximum strains that can be applied are only on the order of a few percent. The greatest strains are likely to be highly localized around topographical features. Therefore, to assess the likelihood of a crack being initiated in a backsheet, we apply small amplitude strains to backsheet films under microscopic examination using a laser scanning confocal microscope. Furthermore, this allows us to monitor both the depth and density of cracks as well as the onset strain. Here we perform these measurements after exposure to UV light.

14 SOLAR ENERGY↗
DOE OSTI2024

Chemical state of nickel nanoparticles during the oxygen evolution reaction in a carbonate-bicarbonate buffer solution

The chemical state of nickel anodes during the oxygen evolution reaction can impact their electrocatalytic performance. Here, X-ray photoelectron and absorption spectroscopies reveal the chemical state of nickel nanoparticles under oxygen evolution reaction conditions in amildly alkaline carbonate-bicarbonate buffer solution. Ni 2+ and Ni 3+ species are observed at the reaction onset potential with a 7:4 ratio, with no remaining metallic nickel. These species include NiO, which increasingly converts to other Ni 2+ and Ni 3+ species once the potential is increased above the onset potential. Conversely, when a 20-nm-thick nickel film is used instead of nickel nanoparticles, a significant amount of metallic nickel remains in the inner layers. Nickel nanoparticles also undergo significant morphological and structural changes during the reaction, as evidenced by ex situ transmission electron microscopy. Amorphization of the nanoparticles is attributed to significant H 2 O incorporation, with the oxygen intensity increasing both in operando and ex situ measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Revisiting the validity of eddy viscosity models for predicting airflow over water waves

In this study, we revisit the validity of eddy viscosity models for predicting wave-induced airflow disturbances over ocean surface waves. We first derive a turbulence curvilinear model for the phase-averaged Navier–Stokes equations, extending the work of Cao, Deng & Shen (2020 J. Fluid Mech. 901, A27), by incorporating turbulence stress terms previously neglected in the linearised viscous curvilinear model. To verify our formulation, we perform a priori tests by numerically solving the model using mean wind and turbulence stress profiles from large-eddy simulations (LES) of airflow over waves across various wave ages. Results show that including turbulence stress terms improves wave-induced airflow predictions compared with the previous viscous curvilinear model. We further show that using a standard mixing-length eddy viscosity yields inaccurate predictions at certain wave ages, as it fails to capture wave-induced turbulence, which fundamentally differs from mean shear-driven turbulence. The LES data show that accurate representations of wave-induced stresses require a complex-valued eddy viscosity. The maximum magnitude of this eddy viscosity scales as ∼𝑢 𝜏 ⁢𝜁 𝑖𝑛𝑛𝑒𝑟 , where 𝑢 𝜏 is the friction velocity and 𝜁 𝑖𝑛𝑛𝑒𝑟 is the inner-layer thickness, the height at which the eddy-turnover time matches the wave advection time scale. This scaling aligns with the prediction by Belcher & Hunt (1993 J. Fluid Mech. 251, 109–148). Overall, the findings demonstrate that traditional eddy viscosity models are inadequate for capturing wave-induced turbulence. More sophisticated turbulence models are essential for the accurate prediction of airflow disturbances and form drag in wind–wave interaction models.

16 TIDAL AND WAVE POWER↗
DOE OSTI2024

Exploiting Saturation Regimes and Surface Effects to Tune Composite Design: Single Platelet Nanocomposites of Peptoid Nanosheets and CaCO 3

Mineral-polymer composites found in nature exhibit exceptional structural properties essential to their function, and transferring these attributes to the synthetic design of functional materials holds promise across various sectors. Biomimetic fabrication of nanocomposites introduces new pathways for advanced material design and explores biomineralization strategies. This study presents a novel approach for producing single platelet nanocomposites composed of CaCO 3 and biomimetic peptoid (N-substituted glycines) polymers, akin to the bricks found in the brick-and-mortar structure of nacre, the inner layer of certain mollusc shells. The significant aspect of the proposed strategy is the use of organic peptoid nanosheets as the scaffolds for brick formation, along with their controlled mineralization in solution. Here, we employ the B28 peptoid nanosheet as a scaffold, which readily forms free-floating zwitterionic bilayers in aqueous solution. The peptoid nanosheets were mineralized under consistent initial conditions (σ calcite = 1.2, pH 9.00), with variations in mixing conditions and supersaturation profiles over time aimed at controlling the final product. Nanosheets were mineralized in both feedback control experiments, where supersaturation was continuously replenished by titrant addition and in batch experiments without a feedback loop. Complete coverage of the nanosheet surface by amorphous calcium carbonate was achieved under specific conditions with feedback control mineralization, whereas vaterite was the primary CaCO 3 phase observed after batch experiments. Thermodynamic calculations suggest that time-dependent supersaturation profiles as well as the spatial distribution of supersaturation are effective controls for tuning the mineralization extent and product. We anticipate that the control strategies outlined in this work can serve as a foundation for the advanced and scalable fabrication of nanocomposites as building blocks for nacre-mimetic and functional materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

A pushered capsule implosion as an alternate approach to the ignition regime for inertial confinement fusion

We report in inertial confinement fusion, the threshold for ignition is a highly dynamic quantity as the sources and sinks of power in the hot spot can vary rapidly. In this article, we consider the ignition condition as a race between heating and disassembly rates and make use of a prior solution to the fusion hot-spot thermodynamics to develop a Lawson-like ignition criteria for pressure × confinement time (p-τ) vs temperature. Low-Z capsule designs reach the temperature for this threshold using as much of the shell as feasible as ablator but then are limited in τ by low stagnated mass. An alternate approach, the pushered single shell (PSS) design [D. D.-M. Ho, S. MacLaren, and Y. Wang, “High-yield implosions via radiation trapping and high rho-R,” paper presented at the 60th Annual Meeting of the APS Division of Plasma Physics, 2018], introduces a dense inner layer of Mo-Be alloy that is smoothly graded outward to pure Be, increasing the confinement time at stagnation and lowering the temperature requirement at the ignition threshold. Here, we describe a PSS ignition design for the National Ignition Facility and use the theory as well as simulations to compare it with the low-Z capsule approach. Additionally, we show how an adjustment to the design is used to anticipate the effects of mixing at the fuel–ablator interface.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

First bromine doped cryogenic implosion at the National Ignition Facility

We report on the first experiment dedicated to the study of nuclear reactions on dopants in a cryogenic capsule at the National Ignition Facility (NIF). This was accomplished using bromine doping in the inner layers of the CH ablator of a capsule identical to that used in the NIF shot N140520. The capsule was doped with 3 × 1016 bromine atoms. The doped capsule shot, N170730, resulted in a DT yield that was 2.6 times lower than the undoped equivalent. The Radiochemical Analysis of Gaseous Samples (RAGS) system was used to collect and detect 79Kr atoms resulting from energetic deuteron and proton ion reactions on 79Br. RAGS was also used to detect 13N produced dominantly by knock-on deuteron reactions on the 12C in the ablator. High-energy reaction-in-flight neutrons were detected via the 209Bi(n,4n)206Bi reaction, using bismuth activation foils located 50 cm outside of the target capsule. The robustness of the RAGS signals suggests that the use of nuclear reactions on dopants as diagnostics is quite feasible.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Numerical investigation of active control of tearing mode by magnetic coils and the role of Δ'

Magnetic feedback stabilization of the tearing mode (TM) is numerically investigated, utilizing the MARS-F code (Liu et al 2000 Phys. Plasmas 7 3681) for toroidal tokamak equilibria. With control coil configurations assumed in this study, magnetic feedback partially or fully stabilizes the TM, with either vanishing or finite equilibrium pressure. The best control is achieved by the combination of internal active coils and internal poloidal sensors. The internal and external tearing indices are evaluated for the close-loop system, based on the MARS-F computed mode eigenvalue and eigenfunction, respectively. In the absence of the favorable curvature effect, these two indices are real-valued and quantitatively agree well with each other. For the equilibrium with finite pressure gradient at the mode rational surface, the favorable average curvature effect becomes important and the close-loop tearing index also becomes complex-valued, partly due to interaction of the feedback system with the dissipative wall eddy current response. Isolating the inner layer and outer region response to magnetic feedback, with either proportional or proportional-derivative actions, allows to establish that feedback stabilization of the TM occurs mainly due to modification of the behavior of the external ideal solution, further confirming the analytic result reported in He et al 2021 Phys. Plasmas 28 012504.

Physics↗
DOE OSTI2023

Enhancing Qubit Readout with Autoencoders

In addition to the need for stable and precisely controllable qubits, quantum computers take advantage of good readout schemes. Superconducting qubit states can be inferred from the readout signal transmitted through a dispersively coupled resonator. Here, this work proposes a readout classification method for superconducting qubits based on a neural network pretrained with an autoencoder approach. A neural network is pretrained with qubit readout signals as autoencoders in order to extract relevant features from the data set. Afterward, the pretrained-network inner-layer values are used to perform a classification of the inputs in a supervised manner. We demonstrate that this method can enhance classification performance, particularly for short- and long-time measurements where more traditional methods present inferior performance.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

X-ray and Neutron Radiography for Quantitative Material Reconstructions

Radiography is a powerful tool to determine the interior structure of objects. X-ray radiography is widely used and provides high-resolution images, though X-rays have limited transmission through materials of high atomic number (Z) and density. In contrast, neutrons can penetrate many materials that are heavily attenuating to X-rays, such as metals, providing contrast in the inner layers of highly attenuating items. Past work has shown the value in using both X-ray and neutron radiography for estimating material thicknesses, though that work was limited to simulated data. Here, we demonstrate quantitative material reconstructions using experimental X-ray and neutron radiography data from lab-based systems, accurately modeling radiography system responses to within a few percent to enable quantitative measures of material thickness. We demonstrate the utility of neutron radiography and X-ray radiography for these quantitative reconstructions and introduce methods for using their complementarity to improve image quality and optimize experimental design.

Gilbert, Andrew J.↗
DOE OSTI2020

“Mirror” magnet experiment for quench studies, quench analysis techniques development and in support of superconducting magnet modeling

In order to progress on various research points related to superconducting magnets, we suggest performing series of tests with induced and natural quenches on a mirror magnet, probably using a “11 T” coil. The “mirror” is to have voltage taps instrumented on half the strands, on both coil ends. It is to be instrumented with multiple spot-heaters, of the order of ten, in designated pole-turn areas. Instrumentation is to include quench antenna array facing the inner coil surface, as well as acoustic sensors on the inner layer pole. Further, acoustic sensors at the magnet ends and an acoustic calibration transducer are to be installed. Thus, we are to test sensitivity and precision of acoustic and quench antenna (QA) array sensors, both at close proximity to the coil, and we are to test and commission acoustic on-magnet real-time “calibration”. New or extended DAQ will be tested as well. In addition to diagnostic development, the purpose of the magnet experiment is to investigate current redistribution in the coil, both during quenching and in operating conditions; to assess voltage build up across strands and in the coil segments during quenching, to explore voltage signature differentiation between different type of quenches; to improve modeling of processes during quenching and for magnet design purposes. In this experiment, we expect to be able to characterize the processes during a quench in unprecedented details.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Applying protective coatings to optical fibers

Apparatus, systems, and methods that provide coats on a glass optical fiber including of an inner layer and an outer layer. The method includes two steps. First, a conductive polymer coating is applied to the optical fiber as it is being produced. Second, a protective coating is applied to that conductive polymer coating. The conductive polymer coating is applied immediately after the fiber is drawn from preform to fiber.

Calta, Nicholas P.↗
DOE OSTI2024

TRISO PARTICLE FUEL POLISHING PROCESS COMPARISON

The investigation of the TRISO coated particles is important in terms of verification the quality of the nuclear fuel samples before placing them in the reactor core. To determine the degree of damage to the coated particles, the samples must be properly polished in order to uncover the inner layers. The poster presents a comparison of two polishing methods. Mechanical polishing method, which is used frequently for sample preparations generates additional mechanical damages in the studied fuel particle, thus directly affecting the experimental results. Due to that, a novel way to polish the samples is presented - an ionic polishing method. Based on the obtained results, it was concluded that the ion polishing method is better because the level of interference with the structures of the individual layers of the tested samples is much lower than with the mechanical method.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Low temperature cofired ceramic substrates and fabrication techniques for the same

A low temperature cofired ceramic substrate comprises a plurality of dielectric layers, at least one inner conductor layer, a plurality of bond pads, and a solder mask. The dielectric layers are formed from ceramic material and placed one on top of another to form a stack. The inner conductor is formed from electrically conductive paste and positioned on an upper surface of at least one inner dielectric layer. The bond pads are positioned on an outer surface of the stack. Each bond pad is formed from a plurality of conductive sublayers of thin film metal stacked one on top of another, with each conductive sublayer being formed from a different metal. The solder mask is positioned on the same outer surface of the stack as the bond pads and includes a plurality of openings, with each opening exposing at least a portion of one of the bond pads.

42 ENGINEERING↗
DOE OSTI2023

Imaging solid–electrolyte interphase dynamics using operando reflection interference microscopy

The quality of the solid–electrolyte interphase is crucial for the performance of most battery chemistries, but its formation dynamics during operation are not well understood due to a lack of reliable operando characterization techniques. Herein, we report a dynamic, non-invasive, operando reflection interference microscope to enable the real-time imaging of the solid–electrolyte interphase during its formation and evolution processes with high sensitivity. The stratified structure of the solid–electrolyte interphase formed during four distinct steps includes the emergence of a permanent inner inorganic layer enriched in LiF, a transient assembly of an interfacial electrified double layer and a consequent emergence of a temporary outer organic-rich layer whose presence is reversible with electrochemical cycling. Reflection interference microscope imaging reveals an inverse correlation between the thicknesses of two interphasial subcomponents, implying that the permanent inorganic-rich inner layer dictates the organic-rich outer layer formation and lithium nucleation. In conclusion, the real-time visualization of solid–electrolyte interphase dynamics provides a powerful tool for the rational design of battery interphases.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

First graded metal pushered single shell capsule implosions on the National Ignition Facility

Graded metal pushered single shell (PSS) capsules are predicted to be a viable alternative to low-Z capsule indirect drive inertial confinement fusion (ICF) implosions for achieving high fusion yields [MacLaren et al., Phys. Plasmas 28, 122710 (2021)]. The first experiments with Be/Cr-graded metal PSS capsules indicate that the implementation of the principle design feature, the graded density inner metal layer, has succeeded in producing a stable implosion with performance in agreement with predictions. With 50% Cr concentration in the pusher, PSS capsules have greater than ~2× higher shell densities during stagnation for enhanced core confinement and radiation trapping at ~35% lower shell implosion velocities than low-Z capsules. High-energy >30 keV inflight shell radiography recorded 215 km/s implosion velocities and show that implosion Legendre mode P 2 asymmetry can be tuned via inner-to-outer beam wavelength separation, similar to other implosions. Shell radiographs and neutron core images show similar P 2 asymmetry, suggesting no symmetry swings between peak implosion velocity and stagnation times. Despite the modest implosion velocities, gas-filled deuterium–tritium capsule implosions generate 10 15 neutron yields at relatively modest core ion temperatures of 2.75 keV, indicating that in spite of the high-density inner layer, the implosions have been stabilized by the design density gradient. When compared with hydrodynamic simulations, the measured yield-over-simulated is 35% due to fuel–pusher mix and other perturbations such as the capsule fill tube. Finally, simple analytical scalings of hot spot pressure and neutron yield show that PSS implosions reach similar performance at lower implosion velocities and higher shell densities to low-Z ICF capsules.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗