SEARCH · Engineering Papers

Results for “imbibition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Coreflood Tests to Evaluate Enhanced Oil Recovery Potential of Wettability-Altering Surfactants for Oil-Wet Heterogeneous Carbonate Reservoirs

Summary Oil-wetness and heterogeneity are two main factors that result in low oil recovery (OR) by waterflood in carbonate reservoirs. The injected water is likely to flow through high-permeability regions and bypass the oil in the low-permeability matrix. In this study, systematic coreflood tests were carried out in both “homogeneous” cores and “heterogeneous” cores with a wettability-altering surfactant. The homogeneous coreflood tests were conducted to evaluate surfactant retention, as well as to compare tertiary surfactant flooding with secondary surfactant flooding. The heterogeneous coreflood test was proposed to model bypassing in low-permeability matrix during waterfloods, and dynamic imbibition of surfactant into the low-permeability matrix. Surfactant retention results suggest that retention increases as initial oil saturation decreases. The retention of selected surfactant in the target reservoir cores was measured to be within a range of 0.07–0.12 mg/g-rock, which is economically acceptable. The results of homogeneous coreflood tests showed that both secondary waterflood and secondary surfactant flood can achieve high OR (>50%) from relatively homogeneous oil-wet cores. A shut-in phase after the surfactant injection resulted in a surge in oil production, which suggests that enough time should be given for wettability alteration by surfactants. The results of heterogeneous coreflood tests showed that more oil is bypassed in the tighter matrix by waterflood if the permeability is higher in the flooded layer and this bypassed oil is the target for the wettability-altering surfactant floods. Slow wettability-altering surfactant injection leads to imbibition into bypassed regions. When the oil-wet carbonate reservoirs have large unswept regions after waterflood, wettability-altering surfactants can significantly improve OR if enough time is given for imbibition.

Engineering↗

DOE OSTI2022

FY22 Progress on Multicontinuum Methods in Containment

Estimation of two-phase fluid flow properties is important to understand and predict water and gas movement through the vadose zone for agricultural, hydrogeological, and engineering applications, such as containment transport and/or containment of gases in the subsurface. To estimate rock fluid flow properties and subsequently predict physically realistic processes such as patterns and timing of water, gas, and energy (e.g., heat) movement in the subsurface, laboratory spontaneous water imbibition with simultaneous temperature measurement and numerical modeling methods are presented in the FY22 progress report. A multiple-overlapping-continua conceptual model is used to explain and predict observed complex multi-phenomenological laboratory test behavior during spontaneous imbibition experiments. This report primarily addresses two complexities that arise during the experiments: 1) capturing the late-time behavior of spontaneous imbibition tests with dual porosity; and 2) understanding the thermal perturbation observed at or ahead of the imbibing wetting front, which are associated with adsorption of water in initially dry samples. We use numerical approaches to explore some of these issues, but also lay out a plan for further laboratory experimentation and modeling to best understand and leverage these unique observations.

58 GEOSCIENCES↗

DOE OSTI2022

Using Direct Numerical Simulation of Pore-Level Events to Improve Pore-Network Models for Prediction of Residual Trapping of CO2

Direct numerical simulation and pore-network modeling are common approaches to study the physics of two-phase flow through natural rocks. For assessment of the long-term performance of geological sequestration of CO 2 , it is important to model the full drainage-imbibition cycle to provide an accurate estimate of the trapped CO 2 . While direct numerical simulation using pore geometry from micro-CT rock images accurately models two-phase flow physics, it is computationally prohibitive for large rock volumes. On the other hand, pore-network modeling on networks extracted from micro-CT rock images is computationally efficient but utilizes simplified physics in idealized geometric pore elements. This study uses the lattice-Boltzmann method for direct numerical simulation of CO 2 -brine flow in idealized pore elements to develop a new set of pore-level flow models for the pore-body filling and snap-off events in pore-network modeling of imbibition. Lattice-Boltzmann simulations are conducted on typical idealized pore-network configurations, and the interface evolution and local capillary pressure are evaluated to develop modified equations of local threshold capillary pressure of pore elements as a function of shape factor and other geometrical parameters. The modified equations are then incorporated into a quasi-static pore-network flow solver. The modified model is applied on extracted pore-network of sandstone samples, and saturation of residual trapped CO 2 is computed for a drainage-imbibition cycle. The modified model yields different statistics of pore-level events compared with the original model; in particular, the occurrence of snap-off in pore-throats is reduced resulting in a more frontal displacement pattern along the main injection direction. Compared to the original model, the modified model is in closer agreement with the residual trapped CO 2 obtained from core flow experiments and direct numerical simulation.

Kohanpur, Amir H.↗

DOE OSTI2021

Influence of interfacial responses of Berea Sandstone in low-salinity waterflooding environments

Wetting conditions and fluid-fluid interfacial properties are essential to understanding oil recovery in the context of low-salinity and smart waterflooding. Many have deemed wettability alteration to be the dominant interaction, while some highlight the importance of fluid-fluid interactions. In some rock-fluid systems, benefits from the use of additives can arise to favor hydrocarbon production. Understanding the balance between the fluid-fluid and rock-fluid interactions when utilizing additives is crucial to evaluate benefits in improved efficiency. Ultimately, this understanding will shed light on recovery mechanisms. Regarding oil recovery, previous studies indicate that the injection of a naphthenic acid (NA) blend dissolved in an injection brine improves oil recovery in Berea Sandstone, particularly under low-salinity conditions. Interfacial rheology results for the brine-oil interface correlated well with the recovery response. This observation was speculated to serve as a potential improved recovery mechanism through oil-trapping suppression. However, the said studies did not evaluate potentially concurrent rock wettability alteration during recovery or the initial wetting condition. The purpose of this work is to determine the production behavior in systems with NAs, namely NA-10 (3-Cyclohexanepropinoic acid), NA-14 (Cyclopentane carboxylic acid), NA-18 (Cyclohexane carboxylic acid), and NA-mix (Naphthenic acid mixture), at different initial wetting conditions under spontaneous imbibition. In addition, we tested the NAs ability to alter wettability in Berea Sandstone and determine each “additive’s” capacity to improve recovery. Here, time-domain nuclear magnetic resonance (TD-NMR), contact angle, and Amott cell tests, i.e. spontaneous imbibition, were used to analyze the influence of the selected naphthenic acids on oil displacement under different initial wetting conditions. Our results indicate that individual naphthenic acids indeed have potential as additives in low-salinity waterflooding for oil-wet systems while negatively impacting recovery in water-wet systems. However, results suggest that the evolution of the interfacial properties and wettability conditions are equally important on the recovery behavior.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2024

Integrated experimental studies of pore structure and fluid uptake in the Bossier Shale in eastern Texas, USA

Within the Haynesville-Bossier Shale complex, the Bossier Shale has not been extensively studied by either industry and academia, despite it being an unconventional gas reservoir and a potential caprock for carbon storage in the underlaying Haynesville Shale. The lack of knowledge of the complex pore structures and fluid-rock interactions hinders the effective extraction of gas and the characterization of fluid reservoirs and sealing capacity. Integrated experimental studies of pore structure and fluid-rock interactions were conducted in seven Bossier Shale core samples collected in eastern Texas. Petrographic, geochemical, and petrophysical properties such as mineral composition, organic richness, thermal maturity, porosity, pore/pore throat diameter distribution, water-accessible pores, liquid water imbibition, and water vapor adsorption were characterized using complementary approaches of thin-section petrography, scanning electron microscopy, X-ray diffraction, total organic matter, pyrolysis, mercury intrusion porosimetry, nuclear magnetic resonance, (Ultra-) small angle X-rays scattering as well as small angle neutron scattering with deuterated liquids and contrast variation. Further, the results show that the thermally mature Bossier Shales are composed of mixed argillaceous mudstone, mixed mudstone, and mixed carbonate mudstone. The shale contains both organic and inorganic pores, with porosities of 3.24-9.37 %, pore-to-throat ratios of 1.65 to 19.4, and water-accessible pores accounting for 28.7-72.6 % of total pores. Approaches of liquid water imbibition and water vapor adsorption, with and without direct contact of water with shale samples, indicate that liquid water first enters the nano-sized pores under high capillary pressures, and water vapor adsorption is mainly controlled by both clay minerals and pores with diameters less than 10 nm. These findings contribute to a better understanding of pore structures and water-shale interactions and their controlling factors in the Bossier Shale.

58 GEOSCIENCES↗

DOE OSTI2022

Effect of a nanoparticle on wettability alteration and wettability retainment of carbonate reservoirs

The oil recovery in many carbonate reservoirs is low due to oil-wetness and heterogeneity. In this study, nanoparticles are evaluated for altering the wettability of oil-wet limestones and their properties are compared with those of an anionic surfactant. A surface-modified silica nanoparticle (SiNP) with a negative zeta potential was found to be aqueous stable in brines. Wettability studies showed that the SiNP cannot change the wettability of an initially oil-wet calcite plate, but SiNP treated calcite surface can remain water-wet after aging in oil. Spontaneous imbibition tests confirmed the observations of wettability tests and showed that a SiNP treated carbonate core retained its water-wettability during oil injection and aging. The imbibition into a SiNP treated and oil aged core was comparable to that in a water-wet core. However, SiNP was not able to remove the oil layers in initially oil-wet cores and imbibe water into these cores. In contrast, the anionic surfactant could alter the oil-wet carbonate rocks to a more water-wet condition, but failed to prevent the water-wet surface from getting oil-wet during oil-aging. The results suggest that the SiNP can be injected into wettability-altered (water-wet) reservoirs/regions to help retain the water-wettability during the long-term oil production. The 0.5 wt% SiNP dispersions transported through 18 mD limestone cores without any plugging. The SiNP retention was measured to be 2.5 mg/m 2 , much higher than that of the anionic surfactant.

02 PETROLEUM↗

DOE OSTI2025

Unsteady- and Steady-State Relative Permeability Study with X-ray and Acoustic Monitoring for CO 2 Storage in Deep Saline Aquifers

In this study, we link the multiphase flow measurements with controls of sedimentary structures (e.g., heterogeneity and anisotropy) on relative permeability to variations in ultrasonic velocities for two deep saline aquifer formations (Entrada and Bluff Sandstones) in the San Juan Basin of the Southwestern USA. The rock specimens were extracted from outcrop sites near Durango, CO, USA. They have distinct differences in grain size, cementation composition, and individual chemical amounts, despite both formations being eolian sandstones. We performed a series of unsteady- and steady-state CO 2 -brine relative permeability experiments under capillary-controlled displacement rates. Unsteady-state experiments were conducted at 71 °C and 9.65 MPa; steady-state experiments were conducted at 85 °C and 22.8 MPa and 89 °C and 24.1 MPa for the Bluff and Entrada Sandstones, respectively. During the unsteady experiments, X-ray computed tomography was used to visualize multiphase flow in porous media and quantify saturations during brine drainage under various flow rates. Scan images and saturation profiles indicate that the CO 2 distribution in the pore volume was strongly impacted by the presence of high-angle cross-laminations, heterogeneous rock structure, and direction of bedding orientation. Those factors contribute to dramatic and quick initial breakthroughs and affect the overall saturation dynamics. Steady-state relative permeability tests were conducted at net flow rates of 1 mL/min for both brine drainage and imbibition. During the experimental steps, the CO 2 fractional flow was increased and decreased for both drainage and imbibition scenarios to mimic the front when CO 2 contacts brine and behind the front when brine enters space previously occupied by CO 2 . It was found that compressional velocity decreased, while shear waves slightly increased as brine saturation decreased. The hysteresis effects for the relative permeability and acoustic velocities were distinct. Furthermore, the CO 2 /brine front stability is quantified by applying a mobility ratio approach to spot saturations at which the boundary line between fluids becomes uneven. The results presented in this work can potentially boost the quality and precision of forecasts for the CO 2 storage projects in which the vertical and horizontal core-scale heterogeneity and anisotropy impact the plume migration within host reservoirs.

carbon dioxide (CO2)↗

DOE OSTI2025

The Impact of Naphthenic Acids on Dynamic Fluid–Fluid Interactions: Implication for Enhanced Oil Recovery

Previous coreflooding results and wettability analyses in our group show that injection of naphthenic-acid-enriched water can improve oil recovery over traditional waterflooding. This observation is still a subject of research efforts without a definitive explanation. Naphthenic acids (NA) have been reported to drive wettability alteration and increase the water–oil interface elasticity. These alterations depend on the NA carbon number and aqueous-phase salinity, among other conditions, as reported in the literature. Smart-water flooding (SWF) research often links recovery to the initial wettability condition, being higher for initially oil-wet rock. SWF refers to a technique in which the aqueous-phase ion composition or/and salinity are changed to maximize oil recovery. Given NAs’ complex solution behavior, selecting acid combinations that prompt oil recovery is a difficult objective. The aim of this research is to determine the effects of select naphthenic acids on the oil–water interfacial rheology and wettability alteration and how these interfacial effects are associated with oil recovery under spontaneous imbibition. NAs were selected based on their carbon number, molecular structure, and solubility in the saline solution used in this research. We aimed at exploring which NAs should be used to regulate interfacial properties so as to either increase oil recovery or accelerate production. Time-domain nuclear magnetic resonance, interfacial dilatational rheology, and liquid-bridge experiments, i.e., proxy of snap-off, were conducted. A baseline was established using results obtained with a previously tested sulfate-rich aqueous phase, shown to be effective in recovering oil. Results show that NA14 and N18 increase the water–oil interfacial viscoelasticity and induce interfacial healing but led to different recovery factors. N10, while effective at inducing water wetness in oil-wet rock, is ineffective at increasing the recovery factor. We concluded that wettability and oil–water interfacial rheology are not exclusive, and instead they can synergistically favor EOR benefits. Moreover, oil recovery benefits under spontaneous imbibition are shown to depend strongly on the initial wettability conditions.

Medina-Rodriguez, Bryan X. (ORCID:0000000262922831↗

DOE OSTI2025

Fluid/Fluid Interfacial Areas Measured for Different Non-Wetting/Wetting Fluid Pairs in Natural Porous Media

This study examined the impact of fluid type and grain diameter on the interfacial area between different pairs of non-wetting and wetting fluids in natural porous media. Synchrotron X-ray microtomography was used to obtain high-resolution, three-dimensional images of multi-phase porous media systems. Multiple porous media, comprising a range of physical and geochemical properties, were used in this study. The four pairs of non-wetting/wetting fluids used were dense OIL/water, light OIL/water, air/dense OIL, and air/water. Images were obtained over a broad range of wetting phase saturation and for both wetting phase drainage and imbibition conditions. The results showed that for each fluid pair, the total (capillary + film) interfacial area increased with decreasing wetting fluid saturation. Interfacial areas were similar among all fluid pairs for a given porous medium. They were also similar for drainage and imbibition conditions. The maximum specific interfacial area (A m ) was shown to correlate well with inverse median grain diameter. The physical properties of the porous medium appear to have a greater influence on the magnitude of specific total interfacial area for a given saturation than fluid properties or wetting phase history.

NAPL↗

NASA NTRS1994

Gravity-regulated formation of the peg in developing cucumber seedlings

It has been proposed that peg formation in the vascular transition region (TR zone) between the hypocotyl and the root in Cucurbitaceae seedlings is a gravimorphogenetic phenomenon. Initiation of the peg became visible 36 h after imbibition when cucumber (Cucumis sativus L. cv. Burpee Hybrid II) seeds were germinated in a horizontal position at 24 degrees C in the dark. Simultaneously, sedimented amyloplasts (putative statoliths) were apparent in the sheath cells surrounding the vascular strands, and in the cortical cells immediately adjacent to them, in the TR zone. In contrast, the other cortical cells, some of which were destined to develop into the peg, contained amyloplasts which were not sedimented. These results suggest that the graviperception mechanism for peg formation may be like that of statoliths in shoot gravitropism. By 48 h following imbibition, the cells of the TR zone still had sedimented amyloplasts but had lost their sensitivity to gravity, possibly because of their maturation.

NASA Program Space Biology↗

DOE OSTI2020

A spatial-statistical investigation of surface expressions associated with cyclic steaming in the Midway-Sunset Oil Field, California

In the Midway Sunset Oil Field in Central California, operators inject steam into the shallow diatomite formation to enhance heavy oil recovery through imbibition, wettability alteration, and viscosity reduction, among other mechanisms. The injected steam, however, does not always remain in the reservoir or return through the wells. In two zones in the study area, the steam comes out at the surface, creating sinkholes, seeps, and steam outlets. These phenomena, called “surface expressions,” pose safety and environmental hazards. Even though these surface expressions are a widespread problem in Central California, they are not well documented and understood. Possible causes of the surface expressions include: high injection pressure, structurally controlled flow patterns, leakage of steam through old improperly abandoned wells, high injection volumes, or flow along naturally occurring faults, among other possible factors. This work examines attributes of the zones with surface expressions in order to determine factors that may contribute to their occurrence. Spatial statistical analysis using logistic regression, random forests, and classification trees is used to explore the relationship between the surface expressions and geological and production-related attributes. The results point to a significant spatial correlation between the surface expressions and two predictors: concentration of plugged wells and geologic seal thickness. The results guide follow-up studies to further investigate the role of well abandonment and seal thickness in the occurrence of surface expressions.

02 PETROLEUM↗

DOE OSTI2023

Impact of controlled prewetting on part formation in binder jet additive manufacturing

Binder jetting is an additive manufacturing process that bonds powder through selectively depositing binder by inkjet printing. The part is then extracted and densified by sintering and/or infiltration. The process offers low costs and fast build rates, but properties can be poor due to residual porosity after sintering. The inkjet printing process may contribute to this residual porosity by creating large pores. The droplet kinetic energy ejects some powder particles from the bed and rearranges others. Particle ejection and rearrangement are theorized to create porous regions in binder-jetted parts. In this work, small amounts of moisture are added to the spread powder before printing and the impact on part formation, part properties, and printing parameters measured with varied droplet spacing, droplet velocity, and print frequency. Moisture is added by applying an atomized fluid mixture to the powder between layer spreading and binder printing. The fluid mixture partially evaporates but leaves a stable residue to increase cohesion and enhance imbibition. Moisture addition to the powder increases the range of droplet spacings for line formation while reducing particle ejection, powder rearrangement, and balling in layer and multilayer parts. Excessive moisture addition decreases the effective saturation of printed lines, but saturation in 3D parts is less impacted. Increased surface roughness in the first few layers of a print was also mitigated with prewetting. Finally, high-speed X-ray imaging verified prewetting reduction in particle ejection and rearrangement.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Concrete shrinkage and creep under drying/wetting cycles

Concrete shrinkage and creep under variable hydric conditions are important factors for the safety and durability of concrete especially in nuclear reactor or nuclear waste storage background. A large (and long – more than 900 days) experimental campaign, conducted on two different concretes, has therefore been designed to study the strains of non loaded and loaded concretes submitted to drying and liquid water imbibition cycles. For the purposes of comparison, concrete strains and mass variations during drying only (50% RH) and/or following cycles of drying/rewetting were also recorded. This allowed the identification of desiccation shrinkage, basic creep and drying creep at 10 MPa of axial stress. Important results were found and have shown that the final mass and strain are not deeply modified by the introduction of a rewetting phase either for a loaded or a non loaded material.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Prediction of moisture transfer in cement-based materials: Use of a porous network model to access transfer parameters

Knowing the water transport phenomena is fundamental for understanding the durability of cement-based materials. The moisture content within cementitious materials is of primary importance because it has a direct influence on mechanical (shrinkage, creep) and chemical (penetration of aggressive agents) degradation. Many models based on the determination of the transfer properties of the material under study already exist but require fitting of the parameters to find the experimental kinetics. Transfer parameters are generally estimated from the empirical approaches developed for soils by Van Genuchten and the water vapour diffusion reduction factor is often calculated via Millington's semi-empirical model. In this paper, we make a proposal to improve the prediction of moisture transfer, through mechanisms such as drying, capillary imbibition and water vapour permeability in cement-based materials, by using a porous network model to access the transfer parameters.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Chemical and isotopic evolution of flowback fluids from the Utica Gas Shale Play, Eastern Ohio USA

For this work, hydraulic fracturing flowback fluids were collected from two Utica/Point Pleasant well pads in eastern Ohio. One site was in the wet gas zone (UPPW), while the site ~50 km south consisted of four wells on the same pad in the dry gas zone (UPPS). Samples of input fluids also were collected before and during hydraulic fracturing. Flowback fluids are Na-Ca-Cl brines with total dissolved salt (TDS) concentrations that increase over several months from ~100 to 200 g/L. The slightly higher TDS of the dry gas fluids are in part due to recycled flowback used as input fluids, and in part due to lower volume of water used in hydraulic fracturing. Concentrations of most major ions (Ca 2+ , Mg 2+ , Na + , Sr2 + , Fe, Mn, Cl – , Br – ) are similar for the five wells sampled, although small but systematic changes occur in the major element ratios over time. Most notably, an increase in the Sr/Cl ratio corresponds to an increase in the 87 Sr/ 86 Sr ratio in the fluids, suggesting interactions with a more radiogenic Sr source in the subsurface. Dissolved Ba concentrations and Ra activities were different between the two sites, reflecting a high SO 4 2– fluid used at the UPPW site, and water-rock reactions occurring during hydraulic fracturing at the UPPS site. Water oxygen (δ 18 O) and hydrogen (δD) isotopes for input fluids used in the UPPW4 well and fresh water used for the UPPS wells fall on the Global Meteoric waterline (GMWL). Flowback fluids from both sites are relatively enriched in δ 18 O and δD compared to the input, but do not appear to follow a simple mixing trend, suggesting reaction and isotopic exchange with carbonates and fractionation due to imbibition in the rock. Cl isotopes, δ 37 Cl in the FP fluids varied from ~ –0.43 to +0.13‰, the largest variation was observed in the earlier stages of flowback, while in the later stages δ 37 Cl exhibited a small but systematic increase over time, suggesting diffusion control of isotopic composition. Some of the trace species measured (dissolved Fe, Mn, thiosulfate and organic acids) do not follow the same trends as the major ions, suggesting contributions from input fluids, or microbially mediated reactions are exerting control on their concentrations. Input water chemistry exerts an important control on the Sr and Ba concentrations in flowback water. High SO 4 2– in the input fluids used for hydraulically fracturing the wet gas well leads to precipitation of barite-celestite in flowback fluids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

The impact of capillary heterogeneity on CO 2 flow and trapping across scales

Capillary heterogeneity has been identified over the last decade as a key control on subsurface CO 2 flow behavior during geological CO 2 sequestration. These heterogeneities can be formed in all sedimentary rocks, ranging from slight variations in the sand grain sizes to extensive sequences of interbedded sands, shales, and limestones. Capillary heterogeneity has been largely, although not entirely, overlooked in subsurface flow modeling because it is assumed to only directly influence fluid redistribution over scales of centimeters to meters. However, even small-scale fluid movements can result in dramatic impacts on the mobility and trapping of the CO 2 over kilometers. Therefore, neglecting capillary heterogeneity at multiple scales could potentially lead to errors in modeling and predicting field-scale plume migration. In this review paper, we aim to provide a consistent overview to (1) establish that capillary heterogeneity can have a major impact on CO 2 plume migration, (2) establish the respective length scales at which capillary heterogeneity matters, and (3) provide guidance for numerical modeling. This review covers pertinent literature and extracts key observations from the core to the field scales. Experimental studies have shown that millimeter-decimeter scale capillary heterogeneity can cause the so-called capillary heterogeneity trapping in addition to pore-scale residual trapping. Even at such a small scale, capillary heterogeneity can already lead to complex upscaled constitutive relationships, such as flow-rate dependent and anisotropic relative permeability, which affects field-scale CO 2 migration even when field-scale heterogeneities are present. Under gravity-dominated flow regimes, centimeter-meter scale capillary heterogeneity can entrap a significant amount of CO 2 at field scale, not just after imbibition but also during drainage. In certain cases, the presence of capillary heterogeneity can even completely stop the vertical movement of the CO 2 plume, hence greatly reducing leakage risks. At meter-kilometer scale, the influence of capillary heterogeneity is more pronounced and can hinder or redirect CO 2 migration in both lateral and vertical directions. The impact of capillary heterogeneity across multiple spatial scales poses a great challenge in modeling CO 2 migration at field scale, because it is practically impossible to build a field-scale earth model with grid blocks at millimeter scale. We recommend a hierarchical modeling approach to address this challenge. At field scale, earth models are built to capture geological features and heterogeneities in high but still practical grid resolutions. For each facies or rock type of the field-scale model, high- resolution meter-scale “conceptual” models are built with millimeter-scale grid blocks to capture representative fine-scale bedding geometries and heterogeneities in various environments of deposition, bridging the gap from subcore scale to the size of a field-scale simulation grid block. Upscaling is then used to preserve the smaller-scale flow dynamics of various rock types in field-scale simulations. Here, future work is needed to (1) refine, improve, and validate the hierarchical modeling approach; (2) build libraries of fine-scale bedding models for facies in various environments of deposition; (3) quantify multiscale capillary heterogeneity effects under subsurface uncertainties; (4) gain learning from different storage formations; and (5) establish best practices that balance accuracy and computational speed.

Capillary heterogeneity↗

DOE OSTI2020

On electrolyte wetting through lithium-ion battery separators

The wettability by electrolyte is a critical characteristic of lithium-ion battery separators since electrolyte absorption is essential for ionic transport. Most importantly, fast absorption of electrolyte facilitates the electrolyte filling and wetting processes during the battery assembly. However, theoretical or experimental investigation of separator wettability has rarely been reported, and thus very little quantitative data can be found in the existing literature. Here, innovative experimental techniques and associated analytical models have been developed to fully characterize the electrolyte wetting behavior through battery separators. Both in-plane and through-plane imbibition processes are investigated. The results show that, electrolyte needs significantly longer time to wet separators than it does for commercial electrodes. The wetting rate depends significantly on the pore size, porosity, and micro-structure of the separators. Electrolyte in-plane wetting is only observed in the separators manufactured by the wet process. Increasing separator porosity and pore size is shown to be substantially increasing through-plane wetting rate. In addition, ceramic coating is shown to increase in-plane wetting but retard through-plane wetting.

25 ENERGY STORAGE↗

DOE OSTI2021

Microfracture-pore structure characterization and water-rock interaction in three lithofacies of the Lower Eagle Ford Formation

The microfracture-pore structures and water-rock interactions of eight samples of three typical lithofacies (three limestone, three wackestone, and two mudstone) from the Lower Eagle Ford Formation have been investigated using an integrated methodology. The methods used were X-ray diffraction (XRD), total organic carbon (TOC) content, pyrolysis, thin-section petrography, scanning electron microscopy (SEM), mercury intrusion porosimetry (MIP), spontaneous water imbibition, and water vapor & nitrogen physisorption. Petrophysical properties such as organic richness, maturity, mineral composition, types and patterns of microfractures and pores, porosity, pore-throat size distribution, pore size distribution, pore connectivity, water adsorption and desorption behavior were determined from these methods, and the results compared among the three lithofacies. For example, the three limestone EAS samples and three wackestone DM samples show a low porosity range from 2.02–3.35%, whereas the two mudstone VRU samples exhibit a much large average porosity of 11.7% by MIP results. Nitrogen physisorption results show that pore size distributions have a good similarity in N2 adsorption volume for the samples with similar lithology. Microfractures are morphologically divided into seven types, with their definitions & pictorial examples presented and possible formation mechanisms proposed. In addition, the water vapor physisorption behavior and their controlling factors are discussed. Here, the water adsorption capacity shows a positive relationship (R 2 = 0.90) with clay content and a negative relationship (R 2 = 0.99) with carbonate content. In general, this integrated study of microfracture-pore structure characterization and water-rock interaction provides some insights of water vapor adsorption behavior in different lithofacies and whether microfractures could be an important pathway for fluid flow.

58 GEOSCIENCES↗