Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “hull”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

The Drag of Airships : Drag of Bare Hulls II

The extension of wind tunnel tests of models of airship hulls to full scale requires an extension from a VL of the order of less than 500 sq.ft./sec., to that of 80000 sq.ft./sec., where V = air speed, feet per second, L = length in feel of the particular form of hull. The reason for this research was to furnish the airship designer with a method for finding the VL curve of any conventional type of hull, using data obtained from actual performance of airships flown prior to 1926.

Havill, Clinton H↗

A Complete Tank Test of a Model of Flying-boat Hull - N.A.C.A. Model 16

A model of a 2-step flying-boat hull, of the type generally used in England, was tested according to the complete method described in the N.A.C.A. Technical Note No. 464. The lines of this model were taken from offsets given by Mr. William Munro in Flight, May 29, 1931. The data cover the range of loads, speeds, and trim angles that may be of use in applying the hull form to the design of any seaplane. The results are reduced to nondimensional form to aid application to design problems and facilitate comparison with the performance of other hulls. The water characteristics of Model 16 are compared with those of Model 11-A, which is representative of current American practice. The results show that when the two forms are applied to a given seaplane design under optimum conditions for each, the performance of Model 16 will be somewhat inferior to that of Model 11-A.

Shoemaker, James H↗

Complete tank tests of two flying-boat hulls with pointed steps - N.A.C.A. Models 22-A and 35

This note presents the results of complete tank test of N.A.C.A. Models 22-A and 35, two flying-boat hulls of the deep pointed-step type with low dead rise. Model 22-A is a form derived by modification of Model 22, the test results of which are given in N.A.C.A. Technical Note No. 488. Model 35 is a form of the same type but has a higher length-beam ratio than either Model 22 or 22-A. Take-off examples are worked out using data from these tests and a previous test of a conventional model applied to an arbitrary set of design specifications for a 15,000-pound flying boat. The comparison of these examples shows both pointed-step models to be superior to the conventional form, and Model 35 to be the better of the two. Model 35 is applied to a hypothetical 100,000-pound flying boat of the twin-hull type and performance calculations are made both for take-off and range. The results indicate that the high performance of this type of hull will enable the designer to use higher wing and power loadings than are found in current practice, with a resulting increase in range and pay load.

Shoemaker, James M↗

A General Tank Test of a Model of the Hull of the British Singapore IIC Flying Boat

A general test was made in the N.A.C.A. tank of a 1/12-size model of the hull of the British Singapore IIC flying boat loaned by the Director of Research, British Air Ministry. The results are given in charts and are compared with the results of tests of a model of an American flying-boat hull, the Sikorsky S-40. The Singapore hull has a greater hump resistance but a much lower high-speed resistance than the S-40.

Dawson, John R↗

Tank tests of two models of flying-boat hulls to determine the effect of ventilating the step

The results of tests made in the N.A.C.A. tank on two models of flying-boat hulls to determine the effect of ventilating the step are given graphically. The step of N.A.C.A. model 11-C was ventilated in several different ways and it was found that the resistance of the normal form is not appreciably affected by artificial ventilation in any of the forms tried. Further tests made with the depth of the step of model 11-C reduced likewise show no appreciable effect on the resistance from ventilation of the step. Tests were made on a model of the hull of the Navy P3M-1 flying-boat hull both with and without ventilation of the step. It was found that the discontinuity which is obtained in the resistance curves of this model is eliminated by ventilating the step.

Dawson, John R↗

A complete tank test of a flying-boat hull with a pointed step -N.A.C.A. Model No. 22

The results of a complete tank test of a model of a flying-boat hull of unconventional form, having a deep pointed step, are presented in this note. The advantage of the pointed-step type over the usual forms of flying-boat hulls with respect to resistance at high speeds is pointed out. A take-off example using the data from these tests is worked out, and the results are compared with those of an example in which the test data for a hull of the type in general use in the United States are applied to a flying boat having the same design specifications. A definite saving in take-off run is shown by the pointed-step type.

Shoemaker, James M↗

Tank Tests of NACA Model 40 Series of Hulls for Small Flying Boats and Amphibians

The NACA model 40 series of flying-boat hull models consists of 2 forebodies and 3 afterbodies combined to provide several forms suitable for use in small marine aircraft. One forebody is the usual form with hollow bow sections and the other has a bottom surface that is completely developable from bow to step. The afterbodies include a short pointed afterbody with an extension for the tail surfaces, a long afterbody similar to that of a seaplane float but long enough to carry the tail surfaces, and a third obtained by fitting a second step in the latter afterbody. The various combinations were tested in the NACA Tank by the general method over a suitable range of loadings. Fixed-trim tests were made for all speeds likely to be used and free-to-trim tests were made at low speeds to slightly beyond the hump speed. The characteristics of the hulls at best trim angles have been deduced from the data of the tests at fixed trim angles and are given in the form of nondimensional coefficients applicable to any size hull.

Parkinson, John B↗

A fast adaptive convex hull algorithm on two-dimensional processor arrays with a reconfigurable BUS system

A bus system that can change dynamically to suit computational needs is referred to as reconfigurable. We present a fast adaptive convex hull algorithm on a two-dimensional processor array with a reconfigurable bus system (2-D PARBS, for short). Specifically, we show that computing the convex hull of a planar set of n points taken O(log n/log m) time on a 2-D PARBS of size mn x n with 3 less than or equal to m less than or equal to n. Our result implies that the convex hull of n points in the plane can be computed in O(1) time in a 2-D PARBS of size n(exp 1.5) x n.

Olariu, S.↗

Corn fiber hulls as a food additive or animal feed

The present invention provides a novel animal feed or food additive that may be made from thermochemically hydrolyzed, solvent-extracted corn fiber hulls. The animal feed or food additive may be made, for instance, by thermochemically treating corn fiber hulls to hydrolyze and solubilize the hemicellulose and starch present in the corn fiber hulls to oligosaccharides. The residue may be extracted with a solvent to separate the oil from the corn fiber, leaving a solid residue that may be prepared, for instance by aggolmerating, and sold as a food additive or an animal feed.

Abbas, Charles↗

Using Big Area Additive Manufacturing to directly manufacture a boat hull mould

Big Area Additive Manufacturing (BAAM) is a large-scale, 3D printing technology developed by Oak Ridge National Laboratory's Manufacturing Demonstration Facility and Cincinnati, Inc. The ability to quickly and cost-effectively manufacture unique moulds and tools is currently one of the most significant applications of BAAM. This work details the application of a BAAM system to fabricate a 10.36 m (34 ft) catamaran boat hull mould. The goal of this project was to explore the feasibility of using BAAM to directly manufacture a mould without the need for thick coatings. The mould was printed in 12 individual sections over a five-day period. After printing, the critical surfaces of the mould were CNC-machined, the sections were assembled, and a final hull was manufactured using the mould. As a result, the success of this project illustrates the time and cost savings of BAAM in the fabrication of large moulds.

3D printing↗

Aerodynamic Characteristics of a Refined Deep-step Planing-tail Flying-boat Hull with Various Forebody and Afterbody Shapes

An investigation was made in the Langley 300-mph 7- by 10-foot tunnel to determine the aerodynamic characteristics of a refined deep-step planing-tail hull with various forebody and afterbody shapes and, for comparison, a streamline body simulating the fuselage of a modern transport airplane. The results of the tests indicated that the configurations incorporating a forebody with a length-beam ratio of 7 had lower minimum drag coefficients than the configurations incorporating a forebody with length-beam ratio of 5. The lowest minimum drag coefficients, which were considerably less than that of a conventional hull and slightly less than that of a streamline body, were obtained on the length-beam-ratio-7 forebody, alone and with round center boom. Drag coefficients and longitudinal- and lateral-stability parameters presented include the interference of a 21-percent-thick support wing.

SEAPLANES - GENERAL STUDIES↗

EBR-II Driver Fuel Cladding Hull Analytical Data

Sharing EBR-II driver fuel cladding hull data with General Atomics under NDA No. 20NDA155. Data share is needed to advance discussions regarding process technologies to decontaminate separated cladding hulls

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Cellulose Fiber Isolation and Characterization from Sweet Blue Lupin Hull and Canola Straw

In this study, cellulose fibers were removed from crop by-products using a combination of sodium hydroxide treatment followed by acidified sodium chlorite treatment. The objective was to obtain high recovery of cellulose by optimizing treatment conditions with sodium hydroxide (5–20%, 25–75 °C and 2–10 h) followed by acidified sodium chlorite (1.7%, 75 °C for 2–6 h) to remove maximum lignin and hemicellulose, as well as to investigate the effect of lignin content of the starting materials on the treatment efficiency. Samples were characterized for their chemical composition, crystallinity, thermal behavior and morphology to evaluate the effects of treatments on the fibers’ structure. The optimum sodium hydroxide treatment conditions for maximum cellulose recovery was at 15% NaOH concentration, 99 °C and 6 h. Subsequent acidified sodium chlorite treatment at 75 °C was found to be effective in removing both hemicellulose and lignin, resulting in higher recovery of cellulose in lupin hull (~ 95%) and canola straw (~ 93%). The resultant cellulose fibers of both crop by-products had increased crystallinity without changing cellulose I structure (~ 68–73%). Improved thermal stabilities were observed with increased onset of degradation temperatures up to 307–318 °C. Morphological investigations validated the effectiveness of treatments, revealing disrupted cell wall matrix and increased surface area due to the removal of non-cellulosics. The results suggest that the optimized combination of sodium hydroxide and acidified sodium chlorite treatments could be effectively used for the isolation of cellulose fibers from sweet blue lupin hull and canola straw, which find a great number of uses in a wide range of industrial applications.

09 BIOMASS FUELS↗

Extended convex hull-based distributed optimal energy flow of integrated electricity-gas systems

Integrated electricity and gas systems are constructed to facilitate the gas-fired generation, and the distributed operation of these integrated systems have received much attention due to the increased emphasis on data security and privacy between different agencies. This paper proposes an extended convex hull based method to address optimal energy flow problems for the integrated electricity and gas systems in a distributed manner. First, a multi-block electricity-gas system model is constructed by dividing the whole system into N blocks considering both physical and regional differences. This multi-block model is then convexified by replacing the nonconvex gas transmission equation with the extended convex hull-based constraints. The Jacobi-Proximal alternating direction method of multipliers algorithm is adopted to solve the convexified model and minimize its operation cost. Finally, the feasibility of the optimal solution for the convexified model is checked, and a sufficient condition is developed. If the sufficient condition is satisfied, the optimal solution for the original nonconvex problem can be recovered from that for the convexified problem. Simulation results demonstrate that the proposed method is tractable and effective in obtaining feasible optimal solutions for multi-block optimal energy flow problems.

24 POWER TRANSMISSION AND DISTRIBUTION↗

New England Aqua Ventus I: 100% Hull Design (Final Technical Report)

This report serves as the final technical report for the US Department of Energy (DOE) award DE-EE0006713 (Award 6713). The project is titled “New England Aqua Ventus I Offshore Wind Advanced Technology Demonstration Project 100% Front-End Engineering and Design (FEED)”. The New England Aqua Ventus I (NEAV) project demonstrates a unique prestressed concrete semi-submersible floating hull technology, called VolturnUS. The technology is applicable to harness nearly 60% of the US offshore wind resource within 50 miles of the coast. The hull will be demonstrated at full-scale with a commercial scale wind turbine connected to the grid in the Northeast US off Monhegan Island, Maine for 20 years.

17 WIND ENERGY↗

The NASA Floater: 15MW Ultra-Light Concrete Hull with Sea-Water Ballast Tuned Mass Damper

In this project, UMaine developed the VolturnUS+ platform; a new 15MW+ ultra-light-weight, corrosion-resistant, concrete floating offshore wind turbine (FOWT) equipped with novel patent pending Heel Tank damping technology. UMaine developed this damping technology to reduce FOWT motions using existing onboard sea-water ballast, which has been integrated into the concrete cruciform hull resulting in reduced platform rigid body motions leading to a lighter hull, increased turbine performance, and a lower LCOE.

17 WIND ENERGY↗

Synthesis and Characterization of Soy Hull Biochar-Based Flexible Polyurethane Foam Composites

Flexible polyurethane foams are a diverse class of materials encompassing furniture, packaging, automotive, and many other industrial and domestic applications. Polyurethane foams are synthesized by the addition of polyols and isocyanates; however, the petroleum origin and toxic nature of isocyanates have driven many to look for more sustainable routes to production. Renewable fillers have emerged as a biobased resource to decrease the carbon footprint of this widely used polymeric material. In this study, soy hulls, as mass-produced, industrial by-products of soybean production, were used to create a biochar beneficial in the synthesis of flexible polyurethane foam composites. The addition of soy hull biochar was found to maintain the compression properties of foams at a decreasing isocyanate index, reducing the amount of isocyanates needed for production. In addition, the addition of biochar decreased the flammability of foams, important for many applications where consumer safety is important. The results point to the ability to create safer, more sustainable, and even more cost-effective polyurethane foams through the reduction in isocyanate use while maintaining the properties of this important class of polymers.

Chemistry↗

Tank tests of a model of a flying-boat hull with a fluted bottom

A 1/5-scale model of a flying-boat hull having flutes in the bottom both forward and aft of the step (NACA model 19) was tested to determine its water performance. The model was also tested after the successive removal of the flutes on the afterbody and forebody. The results from these tests are compared with those from tests of a model of the hull of the Navy PN-8 flying boat and it is concluded that the fluted-bottom model and its modifications are inferior to the model of the PN-8.

Dawson, John R↗