Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “hole insertion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

Thermal Systems and Materials Testing

During my internship, I was involved in Boeing Thermal System/M&P, which handles maintenance and repairs of shuttle tiles, blankets, gap fillers, etc. One project I took part in was the revision of TPS-227, a repair process to tiles that entailed drilling out tile damage and using a cylindrical insert to fill the hole. The previous specification used minimal adhesive for application and when the adhesive cured, there would be several voids in the adhered material, causing an unsatisfactory bond. The testing compared several new methods and I analyzed the number of voids produced by each method to determine which one was most effective at eliminating void space. We revised the original process to apply a light adhesive coat to the top 25% of the borehole and a heavy coat to 100% of the insert. I was also responsible for maintaining the subnominal bond database, which records all unsatisfactory SIP (Strain Isolator Pad) bonds. I then archived each SIP physically for future referral data and statistics. In addition, I performed post-flight tile inspections for damages and wrote dispositions to have these tiles repaired. This also included writing a post-flight damage report for a section of Atlantis and creating summarized repair process guidelines for orbiter technicians.

Aguirre, Nathan↗
DOE OSTI2023

Simulated impact of fill tube geometry on recent high-yield implosions at the National Ignition Facility

Inertial confinement fusion capsules fielded at the National Ignition Facility are filled with deuterium and tritium fuel by means of a fill tube. The fill tube introduces a low-density pathway into the fuel region of the capsule that allows high Z contaminant to invade the hot spot during the course of the implosion. A recent series of nominally identical high-yield implosions on the NIF has exhibited significant variability in performance. We evaluate the impact of the fill tube in these implosions computationally to determine whether variations in fill tube geometry could have contributed to this variability. The main contrast between the fill tube geometry in the six shots was the outer diameter of the capsule bore hole, a conical hole into which the fill tube is inserted. In our simulations, the geometry of the bore hole can play a significant role in the development of nonlinear flows seeded by the fill tube. Additionally, we find that the amount of space between the bore hole and the fill tube is the primary factor that determines the amount of contaminant jetted into the hot spot by the fill tube and, in turn, the level of yield reduction due to the fill tube in our simulations. As a consequence, some capsules with 5 μm fill tubes are predicted to outperform capsules with 2 μm fill tubes. We also find that micrometer-scale changes to bore hole size can impact fusion yields by up to four times near the ignition threshold. Nevertheless, simulation trends do not reproduce experimental yield trends, suggesting that the fill tube geometry was not the primary factor contributing to the observed variability in performance and that the fill tube could be masking sensitivity to other asymmetries such as other micrometer-scale capsule defects like voids that were not included in our simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1997

A Novel Silicon Micromachined Integrated MCM Thermal Management System

"Micromachining" is a chemical means of etching three-dimensional structures, typically in single- crystalline silicon. These techniques are leading toward what is coming to be referred to as MEMS (Micro Electro Mechanical Systems), where in addition to the ordinary two-dimensional (planar) microelectronics, it is possible to build three-dimensional n-ticromotors, electrically- actuated raicrovalves, hydraulic systems and much more on the same microchip. These techniques become possible because of differential etching rates of various crystallographic planes and materials used for semiconductor n-ticrofabfication. The University of Cincinnati group in collaboration with Karl Baker at NASA Lewis were the first to form micro heat pipes in silicon by the above techniques. Current work now in progress using MEMS technology is now directed towards the development of the next generation in MCM (Multi Chip Module) packaging. Here we propose to develop a complete electronic thermal management system which will allow densifica6on in chip stacking by perhaps two orders of magnitude. Furthermore the proposed technique will allow ordinary conu-nercial integrated chips to be utilized. Basically, the new technique involves etching square holes into a silicon substrate and then inserting and bonding commercially available integrated chips into these holes. For example, over a 100 1/4 in. by 1 /4 in. integrated chips can be placed on a 4 in. by 4 in. silicon substrate to form a Multi-Chip Module (MCM). Placing these MCM's in-line within an integrated rack then allows for three-diniensional stacking. Increased miniaturization of microelectronic circuits will lead to very high local heat fluxes. A high performance thermal management system will be specifically designed to remove the generated energy. More specifically, a compact heat exchanger with milli / microchannels will be developed and tested to remove the heat through the back side of this MCM assembly for moderate and high heat flux applications, respectively. The high heat load application of particular interest in mind is the motor controller developed by Martin Marietta for Nasa to control the thruster's directional actuators on space vechicles. Work is also proposed to develop highly advanced and improved porous wick structures for use in advanced heat loops. The porous wick will be micromachined from silicon using MEMS technology, thus permitting far superior control of pore size and pore distribution (over wicks made from sintered n-ietals), which in turn is expected to led to significantly improved heat loop performance.

Kazmierczak, M. J.↗
DOE OSTI2022

A discussion on various experimental methods of impact ionization coefficient measurement in GaN

Impact ionization coefficients play a critical role in semiconductors. In addition to silicon, silicon carbide and gallium nitride are important semiconductors that are being seen more as mainstream semiconductor technologies. As a reflection of the maturity of these semiconductors, predictive modeling has become essential to device and circuit designers, and impact ionization coefficients play a key role here. Recently, several studies have measured impact ionization coefficients. We dedicated the first part of our study to comparing three experimental methods to estimate impact ionization coefficients in GaN, which are all based on photomultiplication but feature characteristic differences. The first method inserts an InGaN hole-injection layer, the accuracy of which is challenged by the dominance of ionization in InGaN, leading to possible overestimation of the coefficients. The second method utilizes the Franz–Keldysh effect for hole injection but not for electrons, where the mixed injection of induced carriers would require a margin of error. The third method uses complementary p–n and n–p structures that have been at the basis of this estimation in Si and SiC and leans on the assumption of a constant electric field, and any deviation would require a margin of error. In the second part of our study, we evaluated the models using recent experimental data from diodes demonstrating avalanche breakdown.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1966

Thermocouples easily installed in hard-to- get-to places

Thermocouple wires attached to charged capacitors are inserted in a drilled hole. An electric charge fuses the thermocouple wires to the host material. This method has shown excellent results in fusing nichrome, chromel, Inconel, and stainless steel wires to nickel, beryllium, iron, steel, Inconel, and stainless steel.

Guenther, F. G.↗
NASA NTRS1974

Stresses in dome-shaped shells of revolution with discontinuities at the apex

Asymptotic solutions of Novozhilov's equations of shells of revolution are derived for axisymmetric and first harmonic loadings. The solutions obtained are valid throughout the shallow and nonshallow regions. Stresses in dome shaped shells of revolution with a discontinuity in the form of a circular hole, a circular rigid insert, or a nozzle at the apex have been investigated. Numerical results are obtained for spheres, ellipsoids, and paraboloids, containing a discontinuity under a internal pressure and moment. Curves depicting stress distributions are given. The influence of three types of discontinuity on the stresses of the shells is also given.

Chen, C. H.↗
NASA NTRS1986

Precise-Conductance Valve Insert

Valve modification provides two operating modes fully open and small, precise leak. Copper insert with radially oriented holes allows small, controllable, precise effusion rate when valve closed or nearly unobstructed flow when valve open. Numerous applications in surface physics, vacuum physics, materials science, gas kinetics, thin films, and other areas of research requiring measured flows of gas into or out of system.

Outlaw, R. A.↗
NASA NTRS1986

Measurement of contact angle in a clearance-fit pin-loaded hole

A technique which measures load-contact variation in a clearance-fit, pin-loaded hole is presented in detail. A steel instrumented pin, which activates a make-or-break electrical circuit in the pin-hole contact region, was inserted into one aluminum and one polycarbonate specimen. The resulting load-contact variations are indicated schematically. The ability to accurately determine the arc of contact at any load was crucial to this measurement. It is noted that this simple experimental technique is applicable to both conducting and nonconducting materials.

Prabhakaran, R.↗
NASA NTRS1987

Lightning discharge protection rod

A system for protecting an in-air vehicle from damage due to a lighning strike is disclosed. It is an extremely simple device consisting of a sacrificial graphite composite rod, approximately the diameter of a pencil with a length of about five inches. The sacrificial rod is constructed with the graphite fibers running axially within the rod in a manner that best provides a path of conduction axially from the trailing edge of an aircraft to the trailing end of the rod. The sacrificial rod is inserted into an attachment hole machined into trailing edges of aircraft flight surfaces, such as a vertical fin cap and attached with adhesive in a manner not prohibiting the conduction path between the rod and the aircraft. The trailing end of the rod may be tapered for aerodynamic and esthetic requirements. This rod is sacrificial but has the capability to sustain several lightning strikes and still provide protection.

Bryan, Charles F., Jr.↗
NASA NTRS1990

Connecting Multiple Wires To A Single Through Hole

Small cup enables more than one wire to be soldered to plated through hole in printed-circuit board. Made of brass plated with silver. Inserted in eyelets or plated through holes and swaged onto boards. Used on breadboard circuits and on newly-manufactured circuit boards. Useful in modification of circuit boards, where they serve as convenient attachment points for jumper wires and leads of added components.

Cortes, Reuben, G.↗
NASA NTRS1977

Two measures of performance in a peg-in-hole manipulation task with force feedback

The results are described from two manipulators on a peg-in-hole task, which is part of a continued effort to develop models for human performance with remote manipulators. Task difficulty is varied by changing the diameter of the peg to be inserted in a 50 mm diameter hole. An automatic measuring system records the distance between the tool being held by the manipulator and the receptacle into which it is to be inserted. The data from repeated insertions are processed by computer to determine task times, accumulated distances, and trajectories. Experiments with both the MA-11 cable-connected master-slave manipulator common to hot cell work and the MA-23 servo-controlled manipulator (with and without force feedback) are described. Comparison of these results with previous results of the Ames Manipulator shows that force feedback provides a consistent advantage.

Hill, J. W.↗
NASA NTRS1991

Repairing A Shaft Prone To Fatigue

Shaft of hydraulic motor now outlives its bearings. Procedure for repairing John Deere Series 50 (or equivalent) hydraulic motor solves problem posed by common type of fatigue failure of shaft. Includes forming internally threaded hole in end of shaft, inserting double-threaded end stud, and adding washers and collars.

Sharp, Roger A.↗
NASA NTRS1992

Avoiding space robot collisions utilizing the NASA/GSFC tri-mode skin sensor

A capacitance based proximity sensor, the 'Capaciflector' (Vranish 92), has been developed at the Goddard Space Flight Center of NASA. We had investigated the use of this sensor for avoiding and maneuvering around unexpected objects (Mahalingam 92). The approach developed there would help in executing collision-free gross motions. Another important aspect of robot motion planning is fine motion planning. Let us classify manipulator robot motion planning into two groups at the task level: gross motion planning and fine motion planning. We use the term 'gross planning' where the major degrees of freedom of the robot execute large motions, for example, the motion of a robot in a pick and place type operation. We use the term 'fine motion' to indicate motions of the robot where the large dofs do not move much, and move far less than the mirror dofs, such as in inserting a peg in a hole. In this report we describe our experiments and experiences in this area.

Prinz, F. B. S.↗
NASA NTRS2012

Microwave Extraction of Volatiles for Mars Science and ISRU

The greatest advantage of microwave heating for volatiles extraction is that excavation can be greatly reduced. Surface support operations would be simple consisting of rovers with drilling capability for insertion of microwaves down bore holes to heat at desired depths. The rovers would also provide support to scientific instruments for volatiles analysis and for volatiles collection and storage. The process has the potential for a much lower mass and a less complex system than other in-situ processes. Microwave energy penetrates the surface heating within with subsequent sublimation of water or decomposition of volatile containing minerals. On Mars the volatiles should migrate to the surface to be captured with a cold trap. The water extraction and transport process coupled with atmospheric CO2 collection could readily lead to a propellant production process, H2O + CO2 yields CH4 + O2.

Ethridge, Edwin C.↗
NASA NTRS1994

Quick connect fastener

A quick connect fastener and method of use is presented wherein the quick connect fastener is suitable for replacing available bolts and screws, the quick connect fastener being capable of installation by simply pushing a threaded portion of the connector into a member receptacle hole, the inventive apparatus being comprised of an externally threaded fastener having a threaded portion slidably mounted upon a stud or bolt shaft, wherein the externally threaded fastener portion is expandable by a preloaded spring member. The fastener, upon contact with the member receptacle hole, has the capacity of presenting cylindrical threads of a reduced diameter for insertion purposes and once inserted into the receiving threads of the receptacle member hole, are expandable for engagement of the receptacle hole threads forming a quick connect of the fastener and the member to be fastened, the quick connect fastener can be further secured by rotation after insertion, even to the point of locking engagement, the quick connect fastener being disengagable only by reverse rotation of the mated thread engagement.

Weddendorf, Bruce↗
NASA NTRS2004

Tool for Insertion of a Fiber-Optic Terminus in a Connector

A tool has been developed for the special purpose of inserting the terminus of an optical fiber in a cable connector that conforms to NASA Specification SSQ- 21635. What prompted the development of the tool was the observation that because of some aspects of the designs of fiber-optic termini and of springs, sealing rings, and a grommet inside the shell of such a connector, there is a tendency for the grommet to become damaged and detached from the sealing rings during installation. It is necessary to ensure the integrity of the grommet for proper sealing and proper functioning of the connector. The special-purpose tool provides the needed protection for the grommet. The grommet-protection tool resembles a funnel into which an axial slit has been cut (see figure). Prior to insertion, the grommet-protection tool is rolled so that one side of the slit overlaps the other side. The rolled-up grommet-protection tool is inserted in one of the connector holes that accommodate the fiber-optic termini and is pushed in until the flange (the wider of the two conical portions) of the tool becomes seated on the connector grommet. Then a special-purpose installation tool is inserted in the flange of the grommet-protection tool and pressed in until it becomes seated in the flange. This operation expands the narrower of the two conical portions of the grommet-protection tool. The installation tool is removed and the grommet-protection tool remains expanded due to the flat surfaces on the axial slit. By use of a standard contact-insertion tool, a fiber-optic terminus is inserted, through the grommet-protection tool, into the connector cavity. By use of a pair of forceps or needle-nose pliers, the grommet-protection tool is then pulled out of the cavity. Finally, the grommet-protection tool is removed from around the installed fiber-optic cable by pulling the cable through the axial slit. Unlike in some prior procedures for installing the fiber-optic termini in the connector, the procedure that involves the use of the present grommet-protection tool does not include the use of lubricants that can contaminate the interior of the connector. The grommet-protection tool is made of a fluoropolymer, taking advantage of the flexibility of such polymers and further taking advantage of the inherent slipperiness of fluoropolymers. Although the tool is designed primarily for insertion of a fiber-optic terminus, it might also be useful for extracting a previously installed fiber-optic terminus.

King, Wes↗
NASA NTRS1990

Nonobstructive Damping For Parts Vibrating In Flows

Vibration-prone parts in fast-flowing liquids or gases damped by simple provision: drill or cast small holes in them and fill holes with particles. Particles absorb vibration energy without obstructing flow. Damping holes add little to cost of manufacturing parts. Reduces masses of parts because masses of inserted particles less than materials removed to make holes.

Panossian, Hagop V.↗