Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Neutron detector development for high-rate neutron reflectometry at the Second Target Station of Oak Ridge National Laboratory

The Second Target Station (STS) at the Oak Ridge National Laboratory Spallation Neutron Source (SNS) is expected to produce a neutron source that is the brightest in the world, having a significantly higher peak brightness compared to the First Target Station (FTS), where the reflectometry instruments already fall short of being able to handle the highest available flux by a factor of ~100. The neutron reflectometers at the SNS FTS are not suitable for the reflectometers planned for the SNS STS because of its unprecedentedly high peak brightness and the already limited capabilities of these instruments at high count rates. Furthermore, the high rate instruments that are now under development are expected to underperform with regard to gamma sensitivity, meaning that signal-to-noise will be reduced and they will be unable to measure weaker reflectance phenomena in the presence of the significant prompt gamma flash at SNS. To address these challenges, we conducted research to advances associated instruments, techniques, and capabilities for the SNS STS reflectometers. More specifically, we investigated the development of a scalable, 2-D positive-sensitive, pixelated, scintillator-based neutron detector module based on a newly developed scintillator. The work has potential for impact on future neutron reflectometry instruments and neutron science performed at the SNS STS. In particular, the improved background rejection capability of the developed detector could extend the available experimental dynamic Q range, allowing it to measure weak reflectance phenomena.

reflectometry, radiation instrumentation, neutron ↗
DOE OSTI2025

Constant-Overhead Fault-Tolerant Bell-Pair Distillation Using High-Rate Codes

We present a fault-tolerant Bell-pair distillation scheme achieving constant overhead through high-rate quantum low-density parity-check (qLDPC) codes. Our approach maintains a constant distillation rate equal to the code rate while requiring no additional overhead beyond the physical qubits of the code. Full circuit-level analysis demonstrates fault-tolerance for input Bell-pair infidelities below a threshold ∼10%, readily achievable with near-term capabilities. Unlike previous proposals, our scheme keeps the output Bell pairs encoded in qLDPC codes at each node, eliminating unencoding overhead and enabling direct use in distributed quantum applications through recent advances in qLDPC computation. These results establish qLDPC-based distillation as a practical route toward resource-efficient quantum networks and distributed quantum computing.

quantum communication, protocols & technology↗
DOE OSTI2022

Novel Co‐Catalytic Activities of Solid and Liquid Phase Catalysts in High‐Rate Li‐Air Batteries

Abstract Li‐air batteries are considered strong candidates for the next‐generation energy storage systems designed for electrical transportation. However, low cyclability and current rates are two major drawbacks that hinder them from further realization. These issues necessitate the discovery of novel materials to significantly enhance the redox process of discharge products. In this study, a novel catalytic system comprised of tin sulfide (SnS) nanoflakes as a solid catalyst and tin iodide (SnI 2 ) as a dual‐functional electrolyte additive is discovered. This system enables operating the battery at high current rates up to 10 000 mA g −1 (corresponding to 1 mA cm −2 ). The SnS catalyst shows outstanding catalytic activity for both oxygen reduction and evolution reactions compared to carbon, noble metals, and other transition metal dichalcogenides. It also exhibits good structural integrity at high rates. The computations indicate numerous possible oxygen reduction sites without oxygen dissociations on the SnS surface through solution mechanism that is likely responsible for the formation of Li 2 O 2 . The calculations also indicate that the role of the SnI 2 is not only reacting with the lithium anode to provide protection but reducing the charge potential by promoting catalytic decomposition of the Li 2 O 2 . This work provides new novel additives for designing high‐rate Li‐air batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

Enabling stable and high-rate cycling of a Ni-rich layered oxide cathode for lithium-ion batteries by modification with an artificial Li⁺-conducting cathode-electrolyte interphase

Ni-rich LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM811) cathodes are investigated to realize high energy density Li ion batteries for long life electric vehicle applications. However, capacity decay and thermal instability due to cathode-electrolyte interfacial degradation remain challenges that require sophisticated surface stabilization methods to address. Here, we propose a strategy, for the first time, to form an artificial Li + -conducting cathode-electrolyte interphase (ALCEI) on the NCM811 cathode surface using a nucleophilic reaction between polysulfides and vinylene carbonate (VC). Furthemore, the as-formed ALCEI layer simultaneously protects the NCM particles from electrolyte corrosion and facilitates Li + ion transport, thus enabling stable and high rate cycling of NCM811. As a result, the ALCEI-modified NCM811 cathode exhibits a high capacity (211.6 mA h g -1 at 0.1C), notable rate capability (134 mA h g -1 at 10C), and superior cycle stability (94.2% over 200 cycles at 1C). These results underscore the use of interfacial engineering in high voltage cathode material development and provide a feasible strategy for stabilizing Ni-rich cathode interfaces in practical Li ion battery applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Performance of photosensors in a high-rate environment for gas Cherenkov detectors

We report the solenoidal large intensity device (SoLID) at Jefferson Lab will push the boundaries of luminosity for a large-acceptance detector, which necessitates the use of a light-gas threshold Cherenkov counter for online event selection. Due to the high luminosity, the single-photon background rate in this counter can exceed 160 kHz/cm 2 at the photosensors. Therefore, it is essential to validate the high-rate limits of the planned photosensors and readout electronics in order to mitigate the risk of failure. We report on the design and an early set of studies carried out using a small Cherenkov counter in a high-rate environment up to 60 kHz/cm 2 , in Hall C at Jefferson Lab. Commercially available multi-anode photomultipliers (MaPMT) and low-cost large-area picosecond photodetectors (LAPPD) were tested using the JLab FADC250 modules for readout. The test beam results show that the MaPMT array and the internal stripline LAPPD can detect and identify single-electron and pair-production events in high-rate environments. Due to its higher quantum efficiency, the MaPMT array provided a better separation between the single-electron and the pair-production events compared to the internal stripline LAPPD. A GEANT4 simulation confirms the beam test performance of our counter device.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Porous Two-dimensional Iron-Cyano Nanosheets for High-rate Electrochemical Nitrate Reduction

Ammonia (NH 3 ) is an essential ingredient in agriculture and a promising source of clean energy as a hydrogen carrier. The current major method for ammonia production, however, is the Haber–Bosch process that leads to massive energy consumption and severe environmental issues. Compared with nitrogen (N 2 ) reduction, electrochemical nitrate reduction reaction (NO 3 RR), with a higher NH 3 yield rate and Faradaic efficiency, holds promise for efficient NH 3 production under ambient conditions. To achieve efficient NO 3 RR, electrocatalysts should exhibit high selectivity and Faradaic efficiency with a high NH 3 yield rate. In this work, we developed two-dimensional (2D) iron-based cyano-coordination polymer nanosheets (Fe-cyano NSs) following in situ electrochemical treatment for high-rate NO 3 RR. Owing to the strong adsorption of nitrate on Fe0 active sites generated via topotactic conversion and in situ electroreduction, 2D Fe-cyano electrocatalyst exhibits high catalytic activity with a yield rate of 42.1 mg h –1 mgcat –1 and a Faradaic efficiency of over 90% toward NH 3 production at –0.5 V (vs reversible hydrogen electrode, RHE). Further electrochemical characterizations revealed that superhydrophilic surface and enhanced electrochemical surface area of the 2D porous nanostructures also contributed to the high-rate NO 3 RR activity. Finally, an electrolyzer toward NO 3 RR and oxygen evolution reaction (OER) in a two-electrode configuration is constructed based on 2D Fe-cyano, achieving an energy efficiency of 26.2%. This work provides an alternative methodology toward topotactic conversion of transition metal nanosheets for NO 3 RR and reveals the often-overlooked contribution of hydrophilicity of the catalysts for high-rate electrocatalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Bioadaptive Ni single atoms unlock high rate microbial electrosynthesis of isopropanol from CO 2

Hybrid systems that integrate electrochemical CO 2 reduction with microbial upgrading offer a viable route to high value organic compounds from CO 2 at ambient conditions. However, electrocatalyst deactivation in microbial growth media remains a key barrier, limiting efficiency and increasing cost. Here we show that a bioadaptive single-atom nickel catalyst (Ni SAC), coupled with genetically engineered Clostridium ljungdahlii, enables robust electrosynthesis of isopropanol (IPA) from CO 2 via a CO-mediated pathway. Instead of relying on H 2 as an electron carrier, the system applies high-rate CO formation in complex growth media, maintaining a tunable CO Faradaic efficiency up to 92%, which is 9.4 to 52.7 times greater than conventional Ag catalysts. This performance supports stable IPA production at current density of 10.8 A/m 2 and production rate of 161.3 mg/L/day. In situ Raman and X-ray absorption spectroscopy, together with theoretical calculations, indicate that the Ni SAC can resist competing organic adsorption and retain its coordination structure during CO 2 reduction in bioelectrolytes, providing a mechanistic basis for the catalyst stability and integrated process performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

High-Rate and Low-Temperature Fabrication of Cu(In,Ga)Se 2 Solar Cells Using AgBr Induced Recrystallization

We present results demonstrating a three-stage, high-rate, low-temperature deposition process for Cu(In,Ga)Se 2 solar cells including a recrystallization step after the second stage, catalyzed by AgBr. The entire deposition and recrystallization process takes place below 450 °C in less than 15 min. Device results with efficiencies exceeding 16% are shown. Here, we achieve very high levels of grain growth and a greater than a 5% absolute increase in device performance because of the recrystallization step relative to an identical process not involving AgBr.

14 SOLAR ENERGY↗
DOE OSTI2026

High-rate heavy-ion tracking using MWPCs and PPACs with an Anti-Discharge Unit

This work reports on the development of two robust, heavy-ion beam tracking concepts operating at low pressure (< 15 Torr) for high rate applications (> 200 kHz). The first concept consists of a Multi-Wire Proportional Counter (MWPC) with a central anode consisting of 12 μm Au-plated Tungsten wires spaced 1 mm from each other. The anode grid is sandwiched between two segmented cathodes aligned orthogonally in the two dimensions for (x,y) particle localization. The second detector is a Parallel-Plate Avalanche Counter (PPAC) that uses the same readout geometry as the MWPC, but replaces the wire anode with a 150 nm silver layer deposited on both sides of a thin (< 1 mg/cm 2 ) polypropylene foil. Additionally, the bias circuitry for the PPAC anode central foil is equipped with an Anti-Discharge Unit (ADU) to prevent transitions from proportional operation to streamer formation, thereby avoiding damaging discharges. The localization capability of both detectors was tested with a low-rate alpha-particle source (241-Am). A position resolution of < 1 mm (FWHM) was achieved under stable, high-gas-gain (> 1000) operating conditions. Their performance in terms of detection efficiency as a function of the isotope charge (Z) was determined by irradiating the detectors with a cocktail beam (Z ≤ 15) with energy of ∼ 100 MeV/u. Full detection efficiency is maintained for all available fragments under optimal operational conditions (i.e., voltage bias). Full detection efficiency was achieved at rates above 200 kHz by irradiating the detectors with a 1 cm diameter 238 U beam at an energy of 143 MeV/u.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Lithium vanadium oxide (Li 1.1 V 3 O 8 ) thick porous electrodes with high rate capacity: utilization and evolution upon extended cycling elucidated via operando energy dispersive X-ray diffraction and continuum simulation

The phase distribution of lithiated LVO in thick (~500 μm) porous electrodes (TPEs) designed to facilitate both ion and electron transport was determined using synchrotron-based operando energy dispersive X-ray diffraction (EDXRD). Probing 3 positions in the TPE while cycling at a 1C rate revealed a homogeneous phase transition across the thickness of the electrode at the 1st and 95th cycles. Additionally, continuum modelling indicated uniform lithiation across the TPE in agreement with the EDXRD results and ascribed decreasing accessible active material to be the cause of loss in delivered capacity between the 1st and 95th cycles. The model was supported by the observation of significant particle fracture by SEM consistent with loss of electrical contact. Overall, the combination of operando EDXRD, continuum modeling, and ex situ measurements enabled a deeper understanding of lithium vanadium oxide transport properties under high rate extended cycling within a thick highly porous electrode architecture.

25 ENERGY STORAGE↗
DOE OSTI2025

Development of a High-Rate Lithium-Air Battery Using a Gaseous CO 2 Reactant

Li-air batteries are considered a potential alternative to Li-ion batteries for transportation applications due to their high theoretical specific energy. Most works in this area focus on use of O 2 as the reactant. However, newer concepts for using gaseous reactants (such as CO 2 , which has a theoretical specific energy density of 1,876 Wh/kg) provide opportunities for further exploration. The main objective of this project was the development of a novel strategy that enables operation of Li-CO 2 batteries at high-capacity and high-rate, with a long-cycle-life. The team was able to: (1) Synthesize two novel transition metal chalcogenide (TMC) catalysts that work in synergy with ionic liquid-based electrolytes to enhance the efficiency of reactions during discharge and charge processes; (2) Fabricate high-porosity cathode electrodes with 3D printing to increase electrode surface area and gas permeability; (3) Develop a multiscale modeling framework that integrates Density Functional Theory (DFT), Ab-Initio Molecular Dynamics (AIMD), classical Molecular Dynamics (MD), and Finite Element Analysis (FEA) to investigate atomic and cell-level properties of Li-CO 2 batteries; (4) Assemble a stackable Li-CO 2 pouch-cell able to deliver a capacity of >200 mAh. These achievements were realized through an integrated approach based on materials synthesis, testing, characterization, analysis, and computation. This project produced a thorough understanding of key chemical, electronic, and kinetic parameters that govern the operation of Li- CO 2 batteries in realistic conditions. The methodologies employed, and the insight generated, will be valuable beyond advancing the field of Li-CO 2 batteries

25 ENERGY STORAGE↗
DOE OSTI2023

Development of a large array of Silicon Drift Detectors for high-rate synchrotron fluorescence spectroscopy

An array of small-area Silicon Drift Detectors (SDD), named Hera, has been developed at Brookhaven National Laboratory (BNL) in the past few years. Its primary application is high-rate spectroscopy at synchrotrons. Each SDD pixel is a 1 mm × 1 mm square to match the footprint of the original diode-based pixel detector called Maia, which was developed for the same application. The replacement of the diode with an SDD allows for better energy resolution at short shaping times and an increased stability of the detector. 32, 96, and 384-channel arrays were designed and fabricated and achieved a Full Width Half Maximum (FWHM) as low as 176 eV at 5.9 keV with peaking time of 1 μs at -13°C. The sensor design, simulation, fabrication, its readout system, and its spectroscopic performance are reported.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

A High-Rate Lithium Manganese Oxide-Hydrogen Battery

Rechargeable hydrogen gas batteries show promises for the integration of renewable yet intermittent solar and wind electricity into the grid energy storage. Here, we describe a rechargeable, high-rate, and long-life hydrogen gas battery that exploits a nanostructured lithium manganese oxide cathode and a hydrogen gas anode in an aqueous electrolyte. The proposed lithium manganese oxide-hydrogen battery shows a discharge potential of ~1.3 V, a remarkable rate of 50 C with Coulombic efficiency of ~99.8%, and a robust cycle life. A systematic electrochemical study demonstrates the significance of the electrocatalytic hydrogen gas anode and reveals the charge storage mechanism of the lithium manganese oxide-hydrogen battery. This work provides opportunities for the development of new rechargeable hydrogen batteries for the future grid-scale energy storage.

25 ENERGY STORAGE↗
DOE OSTI2023

A High‐Rate Li–CO 2 Battery Enabled by 2D Medium‐Entropy Catalyst

Abstract Lithium‐air batteries based on CO 2 reactant (Li–CO 2 ) have recently been of interest because it has been found that reversible Li/CO 2 electrochemistry is feasible. In this study, a new medium‐entropy cathode catalyst, (NbTa) 0.5 BiS 3 , that enables the reversible electrochemistry to operate at high rates is presented. This medium entropy cathode catalyst is combined with an ionic liquid‐based electrolyte blend to give a Li–CO 2 battery that operates at high current density of 5000 mA g −1 and capacity of 5000 mAh g −1 for up to 125 cycles, far exceeding reported values in the literature for this type of battery. The higher rate performance is believed to be due to the greater stability of the multi‐element (NbTa) 0.5 BiS 3 catalyst because of its higher entropy compared to previously used catalysts with a smaller number of elements with lower entropies. Evidence for this comes from computational studies giving very low surface energies (high surface stability) for (NbTa) 0.5 BiS 3 and transmission electron microscopystudies showing the structure being retained after cycling. In addition, the calculations indicate that Nb‐terminated surface promotes Li–CO 2 electrochemistry resulting in Li 2 CO 3 and carbon formation, consistent with the products found in the cell. These results open new direction to design and develop high‐performance Li–CO 2 batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Transition Metal Dichalcogenides as Effective Catalysts for High-Rate Lithium–Sulfur Batteries

In today’s renaissance of high energy density secondary batteries, lithium-sulfur (Li-S) batteries represent one of the most promising candidates for the next generation of renewable energy storage systems, due to sulfur’s high theoretical specific capacity of 1675 mAh g -1 and high earth abundance. However, despite decades of study, the issues associated with capacity fade via the polysulfide shuttle and sluggish kinetics remain. Through a rigorous and detailed electrochemical study of lithium polysulfides via rotating disk electrode voltammetry (RDE), we have investigated the kinetics of the redox reactions, and explored candidate catalysts to potentially overcome/mitigate the polysulfide shuttle effect. From these RDE studies, supported by comprehensive electronic-structure calculations of conversion-type surface reactions, we determined that WSe 2 can effectively catalyze the polysulfide redox reaction, though further studies are necessary to improve overall Li-S battery performance.

25 ENERGY STORAGE↗
DOE OSTI2024

Synergizing superwetting and architected electrodes for high-rate water splitting

Water splitting is one of the most promising technologies for generating green hydrogen. To meet industrial demand, it is essential to boost the operation current density to industrial levels, typically in the hundreds of mA cm -2 . However, operating at these high current densities presents significant challenges, with bubble formation being one of the most critical issues. Efficient bubble management is crucial as it directly impacts the performance and stability of the water splitting process. Superwetting electrodes, which can enhance aerophobicity, are particularly favorable for facilitating bubble detachment and transport. By reducing bubble contact time and minimizing the size of detached bubbles, these electrodes help prevent blockage and maintain high catalytic efficiency. Here, in this review, we aim to provide an overview of recent advancements in tackling bubble-related issues through the design and implementation of superwetting electrodes, including surface modification techniques and structural optimizations. We will also share our insights into the principles and mechanisms behind the design of superwetting electrodes, highlighting the key factors that influence their performance. Our review aims to guide future research directions and provides a solid foundation for developing more efficient and durable superwetting electrodes for high-rate water splitting.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Highly Loaded Sulfur Cathode, Coated Separator and Gel Electrolyte for High Rate Li-Sulfur Batteries

As one of DOE Battery 500 Seedling projects, Cornell University and EIC Labs investigated and developed i) highly loaded sulfur cathodes (> 3 mg/cm 2 ), ii) hybrid separators, and iii) gel ceramic electrolytes (GCE) to mitigate the low rate capability, shuttling effect and limited cycle life in high performance Li-Sulfur batteries. Scalable nanomanufacturing processes such as air-controlled electrospray (ACES) and gas-assisted electrospinning (GAES) have been utilized to develop directly deposited electrodes and polymer/ceramic hybrid separators. First, in the development of highly loaded cathodes, alternating layers of sulfur impregnated mesoporous carbon and graphene were fabricated via ACES and the resulting layered cathodes and coated separators exhibit higher capacity and capacity retention (about 1,000 mAh/g capacity with less than 0.02% fade/cycles) than single layer cathode or cathode prepared by conventional slurry cast. Alternating layer approach via ACES has been applied to high loading systems (3 - 5 mg S/cm 2 ), demonstrating the potential to increase sulfur utilization and capacity retention. We have also incorporated iron oxides (Fe 3 O 4 ) into S/mesoporous carbon/graphene cathodes to enhance sulfur utilization and mitigation of polysulfide shuttling. and the effect of Fe 3 O 4 in mesoporous carbon and Gr is highly pronounced at high C rates of 1C and 2C cycling performance. To further improve the cathodes at high rates, graphene nanoribbons (GNR) which can promote ion transport were incorporated in the cathode, resulting in 550 mAh/g at 5C/5C rates. Hybrid Li-ion/Li-S cathodes has also been explored to better engage unreacted polysulfides during charge/discharge. S/LFP hybrid cathodes offer higher sulfur utilization and enhanced rate capability, as well as higher areal loading. This study suggests inclusion of iron phosphide (Fe2P) which can chemically interact with polysulfides can further enhance sulfur utilization and mitigation of soluble polysulfides at high rates. Secondly, in the development of hybrid separators, we first employed graphene coating on the commercial polyolefin separators, which exhibits higher capability, better capacity retention and enhanced rate capability. To improve the rate capability with enhanced safety features such as thermal stability and nonflammability, we developed polymer/ceramic hybrids based on thermally stable polyimide (PI) and room temperature curable ceramic precursors such as organopolysilazane (OPSZ) or polysilsesquioxanes (PSSQ), which exhibit no shrinkages up to 300 ºC and non-flammability. To improve mechanical properties and electrochemical stability, polybenzimidazole (PBI) and alumina have been incorporated in polymer/ceramic hybrid separator, replacing PI and OPSZ/PSSQ, respectively. Finally, the gel ceramic electrolyte (GCE) based on ceramic cross linkers have been applied to make Li-S cells even safer and also to mitigate the polysulfide shuttling further. The resulting gel ceramic electrolyte offers improved capacity retention and rate capability, and also effectively mitigates polysulfide shuttling which was also confirmed by modeling. Inclusion of high ion conducting additives into GCE together with polymer/ceramic hybrid separators exhibit the higher ionic conductivity than liquid electrolyte with commercial polyolefin separator. We demonstrated that the developed highly loaded sulfur cathodes, polymer/ceramic hybrid separators and gel ceramic electrolyte can effectively mitigate the low rate capability, shuttling effect and limited cycle life in high performance Li-Sulfur batteries with improved safety.

25 ENERGY STORAGE↗