Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high cycle fatigue”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

The Grain Boundary Relaxation (GBR) Approach for Manufacturing High Strength Nanocrystalline Lightweight Metals

The overarching goal of the project was to conduct research and development work as proposed in the Statement of Project Objective (SOPO) of the award document DE-FE-0009116. The project had 4 tasks and 12 milestones. All the milestone deliverables were completed. The accomplishments of the project objectives and technical discussions are described in Sections 3 and 4, respectively. The modeling and simulation work indicated that to increase the strength and stability of nanocrystalline aluminum (Al), selection of dopants, such as Mg, is necessary. It was predicted that the crystallite size should be less than 50 nm to give high strength. On the basis of modeling, cryo-milling of Al was conducted with the addition of Mg as a function of different times. The crystallite size of the cryo-milled powders was determined by XRD and TEM. Both measurements showed that the actual crystallite size of the grain was <40 nm. The thermal stability of the grain size was established as a function of temperature. It was established that the grain size was < 50 nm up to 500C. The crystallite size of the bulk sample prepared by spark plasma sintering (SPS) and cold spray (CS) additive manufacturing was less than <40 nm. The mechanical properties of the bulk samples prepared by SPS and CS, showed excellent microhardness, good tensile properties (>200 MPa) with moderate ductility and improved fatigue performance. Adding yttria stabilized zirconia (YSZ) improved the build thick of the CS sample, however the YSZ was getting embedded into the sample. A highly dense SPS samples sent for 3rd party testing to the Innovation Testing Services showed a minimum hardness of 180 HV with an average tensile strength of 512.5 MPa. The high cycle fatigue tests also showed an endurance limit of 179.5 MPa. The Energy cost evaluations showed an overall energy cost of around $\$$17.05 for the cryomilling and SPS processes and the total manufacturing cost calculations of $\$$78.14 for 1 kg of sample. The energy cost to prepare a Kg of CS sample is $\$$17.60 and the overall manufacturing cost is $\$$86.85.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Fatigue of laser powder bed fusion processed 17-4 stainless steel using prior process exposed powder feedstock

The rapid pace of development seen in the metal additive manufacturing (AM) process of laser powder-bed fusion (LPBF) requires in-step advances in processes qualification to enable full-scale adoption. This particularly applies to quantifying how powder feedstock conditions impact end-component quality. Here this study examines how in-machine 17-4 stainless steel powder feedstocks are affected by prior LPBF processes, and how these effects impact subsequent builds. Examinations of powder morphology, chemistry, flowability, and rheology were conducted to characterize the powder conditions. The resultant effects of powder feedstock condition on produced component quasi-static tensile and high-cycle fatigue properties were analyzed. Fatigue life was analyzed using a reliability modeling approach that enabled a robust statistical comparison of life. Powder characteristics were found to evolve with powder exposure to prior LPBF processes, particularly in the extremes of powder size distribution and measures of bulk flow. No significant effects of these changes on tensile properties were observed. Reliability modeling methods, including the lognormal and Weibull distributions as well as the empirical survival function, are shown to be effective tools for modeling fatigue variability in LPBF manufactured components. Through these tools, fatigue life was found to be invariant with changes in powder condition.

42 ENGINEERING↗
DOE OSTI2020

Optimizing Piezoelectric Material Location and Size for Multiple-Mode Vibration Reduction of Turbomachinery Blades

Modern turbomachinery blades have extremely low inherent damping, which can lead to high transient vibrations and failure through high-cycle fatigue. Smart materials enable vibration reduction while meeting strict blade requirements such as weight and aerodynamic efficiency. In particular, piezoelectric-based vibration reduction offers the potential to reduce vibration semi-actively while simultaneously harvesting sufficient energy to power the implementation. The placement and the size of the piezoelectric material is critical to the vibration reduction capabilities of the system. Furthermore, the implementation should target multiple vibration modes. In this study, we develop a procedure to optimize electromechanical coupling across multiple vibration modes for a representative turbomachinery blade with surface-mounted piezoelectric patches. Experimental validation demonstrates good coupling across three targeted modes with a single piezoelectric patch. Placing the piezoelectric material in regions of high signed strain energy for all targeted modes enables vibration reduction across all of the targeted modes.

36 MATERIALS SCIENCE↗
DOE OSTI2024

High-Power Targetry R&D for Next-Generation Accelerator Target Facilities

Beam-intercepting devices such as beam windows and particle-production targets are critical components of accelerator target facilities for High Energy Physics (HEP) experiments. The high-power, pulsed structure of the particle beams used for these experiments leads to thermal shock and high-cycle fatigue in addition to radiation damage resulting from the accumulated particle fluence. This can lead to degradation of the target system s mechanical and thermal properties; considerably reducing their lifetimes and presenting substantial challenges to reliable operation of multi-MW class facilities. Recently several major accelerator facilities have been forced to operate at reduced power levels due to target survivability concerns. Furthermore, at Fermilab it is planned to increase the neutrino production beam power up to 2.4 MW in coming years. Therefore, timely R&D on the irradiated behavior of target system materials is critical to efficient operation of accelerator facilities and full utilization of recent accelerator power upgrades for HEP research. This talk will begin with an overview of high-power targetry, and the significant challenges presented by beam power increases expected for future HEP experiments. We will then cover several past materials irradiation studies that have been completed by the High-Power Targetry R&D group at Fermilab and its collaborators on common accelerator and target materials such as graphite, beryllium, titanium, and tungsten. Finally, we will conclude with a discussion of two novel materials investigations under way within the group; high-entropy alloys for beam window applications, and electrospun nanofibers to serve as particle production targets.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Surface smoothing for laser powder-bed Ti-6Al-4V by a transient liquid phase

Surface roughness is the primary driver of fatigue for additively manufactured metals. To address surface roughness, this work introduces a new method to smooth features beyond line-of-sight without material removal. The method applies a coating that triggers local surface remelting by activating a eutectic reaction during heat treatment. The associated liquid phase then wets and isothermally solidifies into a smoother surface. For Ti-6Al-4V fabricated with laser powder bed fusion, samples with and without TLP smoothing (using a Cu coating) were characterized with a suite of techniques, including mechanical testing, electron backscatter diffraction, synchrotron X-ray tomography, and fractography. TLP smoothing reduced surface roughness by 80% and amplified compressive residual stress at the surface by about 50%. With statistically equivalent virtual microstructures, crystal plasticity scrutinized the roles of phases, porosity, and surface roughness. Although the tensile strain-to-failure was reduced to 1% strain, the TLP smoothing process increased high-cycle fatigue strength by about 20% compared to control samples, pointing to future opportunities to optimize the new process through various coating compositions and heat treatment schedules. Overall, this work establishes a new paradigm for treating surfaces of materials for smoothness and compressive residual stress.

Additive manufacturing↗
DOE OSTI2024

Quantitative analysis of three-dimensional fatigue crack path selection in Mg alloy WE43 using high-energy X-ray diffraction microscopy

Fatigue short-cracks in Mg alloys display complex growth behavior due to high plastic anisotropy and crack path dependence on local microstructural features. In this study, the three-dimensional crystallography of short-crack paths in Mg alloy WE43 was characterized by mapping near-field high-energy X-ray diffraction microscopy (HEDM) reconstructed grain maps to high-resolution X-ray CT reconstructions of the fracture surfaces in the crack initiation and short-crack growth regions of six ultrasonic fatigue specimens. Crack–grain–boundary intersections were analyzed at 81 locations across the six crack paths. The basal intragranular, non-basal intragranular, or intergranular character of short-crack growth following each boundary intersection was correlated to crystallographic and geometric parameters of the trailing and leading grains, three-dimensional grain boundary plane, and advancing crack front. The results indicate that crack paths are dependent on the combined crystallographic and geometric character of the local microstructure, and crack path prediction can be improved by use of dimensionality reduction on subsets of high-linear-correlation microstructural parameters.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Micropolar deep material network

This study extends the Deep Material Network (DMN), a physics-informed machine learning framework, to predict the homogenized mechanical response of composite materials with micropolar (Cosserat-type) constitutive behavior. This extension incorporates microstructure-dependent size effects, enabling accurate, efficient, and size-aware predictions for composites with complex internal architectures. While traditional, direct numerical simulation micropolar models effectively capture size effects by introducing extra local degrees of freedom, they bring significant computational challenges, particularly for multiscale analyses relevant to engineering applications. The micropolar DMN developed in this paper achieves high accuracy while significantly reducing computation time compared to micropolar direct numerical simulations. This advancement enables multiscale analyses and parameter studies that were previously impractical, such as high-cycle fatigue simulations and comprehensive investigations of internal length scale effects notably in size-dependent plastic response and the optimization of lattice structures. By uniting microstructure-sensitive modeling, physics-driven learning, and scalable surrogate modeling, the micropolar DMN paves the way for accelerated material design, large-scale parametric studies, and the reliable incorporation of size-dependent effects across a wide range of engineering applications, including optimization and next-generation composite design.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Enhancing functionalities in carbon fiber composites by titanium dioxide nanoparticles

Carbon fiber composite's high specific strength makes it incredibly useful for structural applications. However, their low strain-to-failure can be problematic in structural applications that can potentially see high strain conditions or high fatigue cycles resulting in sudden, catastrophic failure. This is further complicated by damage manifesting within the composite thus not showing damage indicators on the surface. Therefore, monitoring the structural integrity and strain history of the composite in application by itself—while maintaining positive composite performance—is vital to ensure safe operation. In this study, a homogeneous dispersion of TiO 2 nanoparticles on carbon fiber is demonstrated to generate a piezoresistive carbon fiber polymer matrix composite with enhanced self-sensing capabilities. The nanoparticle-embedded composites also exhibited superior strength and damping potential compared to the nanoparticle-free composites. The apparent interlaminar shear strength increased by up to 15% and the damping loss factor increased by an average of 150% while the piezoresistive sensitivity increased by up to 180% with the addition of a small weight fraction of nanoparticles to the fiber surface. These results demonstrate an approach to simultaneously improve the sensing capabilities, damping behavior and mechanical strength of carbon fiber composites by simply adding nanoparticles in the fiber sizing using a commercially scalable deposition method.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Thermal-striping analysis methodology for sodium-cooled reactor design

Computational fluid dynamics simulations have been performed to study the applicability of engineering CFD methods for thermals striping analysis. Thermal striping is the fluctuating temperature profile in a solid caused by fluctuating fluid temperature, and the resulting fluctuating thermal stresses cause high cycle fatigue and eventual material failure. Here this study presents the methodology for thermal striping analysis that including a transient conjugate heat transfer RANS model and benchmark the results against a sodium triple jet experiment. The multiphysics calculations are implemented to analyze the thermal stresses in the solid domain caused by the coupled heat transfer between the fluid and solid domains. Validation data from a liquid sodium triple jet experiment include time-averaged temperature measurements and power spectra of the temperature signal. The numerical results agree well with these experimental measures, demonstrating key features such as the dominant frequency of temperature fluctuations. The applicability of a low-cost wall treatment method is demonstrated, enabling key computational savings. Finally, the performance of two finite element stress analysis software packages is compared, and the validity of the lower-cost method is confirmed. These results demonstrate the applicability of engineering methods for computational thermal striping calculations, enabling thermal striping estimations in large fluid systems such as the core of a Sodium-cooled nuclear reactor.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

The Physical and Engineering Limits of Coupled In situ TEM Experiments

Almost all future energy systems (advanced nuclear reactors, fusion energy system, concentrating solar-thermal power (CSP), and wind technologies) are limited by degradation of key material systems exposed to multiple environmental stressors. The degradation during exposure to high temperatures, radiation, mechanical loading, and chemical attack is often dictated by mechanisms active at the microstructural level. The nature of these mechanisms and the associated variations between sequential and concurrent interplay can be explored if the transmission electron microscope (TEM) is utilized as a toolbox for exploration [1]. One such tool developed at Sandia National Laboratories to couple several of these environments is the In situ Ion Irradiation TEM (I3TEM) [2]. Several studies over the last decade utilizing this tool have shown that the scientific intuition developed over decades of sequential experiments is not always a good indicator of concurrent mechanisms or failure routes. This presentation will highlight the recent and planned additions into the I3TEM facility of a Waviks gas injection system and Raman system, respectively, as can be seen in Fig. 1, permitting environmental degradation from gas species leaked into the pole piece region during quantitative mechanical loading (indentation, monotonic loading, high temperature creep, irradiation induced creep, and high-cycle fatigue); multi-beam ion irradiation (energies ranging from 1 keV to 48 MeV and species from H to Au); laser exposure (20 W and 1064 nm), or various combinations thereof that are already possible [3]. This addition permits the facility to explore both sequential or concurrently the four axes of stressors: thermal, mechanical, radiation, and chemical. This information can be directly coupled to modeling, expediting the refinement and validation of both atomistic and mesoscale models.

degradation↗
DOE OSTI2022

Bayesian optimized collection strategies for fatigue strength testing

Abstract A statistical framework is presented enabling optimal sampling and analysis of constant life fatigue data. Protocols using Bayesian maximum entropy sampling are built based on conventional staircase and stress step methods, reducing the requirement of prior knowledge for data collection. The Bayesian Staircase method shows improved parameter estimation efficiency, and the Bayesian Stress Step method shows equal accuracy to the standard method at larger step size allowing experimentalists to lessen concerns of loading history. Statistical methods for determining model suitability are shown, highlighting the influence of protocol. Experimental validation is performed, showing the applicability of the methods in laboratory testing.

36 MATERIALS SCIENCE↗
DOE OSTI2024

High Strength Aluminum Additive Manufacturing

High-strength aluminum alloys for elevated temperature applications are desirable to replace heavier and more expensive titanium alloys. However, most aluminum alloys lose a large fraction of their strength at temperatures above approximately 200°C. ORNL has designed DuAlumin-3D, an alloy with nominal composition Al-9Ce-4Ni-0.5Mn-1Zr (wt.%), which utilizes the high cooling rates in additive manufacturing (AM) to achieve a refined microstructure, and thermally stable mechanical properties. DuAlumin-3D was fabricated by laser powder bed fusion and tested for its tensile mechanical properties across a range of temperature, and for its room temperature high-cycle fatigue resistance. The alloy was tested in both the as-printed and heat treated conditions, and both parallel and perpendicular to the AM build direction. The alloy was found to have anisotropic mechanical behavior in the as-printed state, but the anisotropy significantly decreased (both for tensile and fatigue properties) following heat treatment. The tensile properties significantly out-performed benchmark wrought 2219-T61 across a wide temperature range. The room temperature fatigue performance was approximately similar to 2219-T61.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Advanced Coating Compositions and Microstructures to Improve Uptime and Operational Flexibility in Cyclic, Low-Load Thermal Utility Plants

GE, the University of Tennessee, and Oak Ridge National Laboratory collaborated from 2020 to 2023 developing two key technologies for improving the viability of fuel switching and load following in thermal utility plants: a) cost-effective weld overlay compositions for boiler tubing b) cathodic arc coatings that deliver improvements in both erosion resistance and oxidation resistance in high temperature steam for HP turbine blades The team worked through a robust, logical project map to de-risk these two technologies and advance them from TRL 3 to TRL 6. For the cost-effective weld overlay, the team developed a ferritic filler material which was fabricated at a vendor for 18% the average market cost of Inconel 625 wire, had a corrosion rate 3x lower in conditions simulating a biomass-fired superheater and 10x lower in conditions simulating a coal-fired superheater, and was fabricated into prototype overlaid tubing that passed ASME requirements including transverse bending, dye penetrant inspection, and ASTM G-76 evaluation. For the cathodic arc coatings applied to steam turbine blades, the team developed a novel composition that was successfully transferred to a qualified vendor. The vendor was able to produce coated prototypes with 4x the as-deposited erosion resistance and 10.4x the post-steam-exposure erosion resistance of the TiN coating the vendor currently applies on GE steam turbine components, without significantly increasing process cost. These coated prototypes also passed a GE inspection and showed favorable performance in high temperature erosion, nanoindentation, sliding wear, scratch adhesion, and high cycle fatigue testing. If successfully deployed by GE, it is anticipated that the technologies will enable the following: • 25%-50% increase in time between outages for both boilers and HP turbines. • 50% decrease in cost for weld overlay on a per foot basis relative to todays NiCr alloys. • Adequate oxidation resistance and erosion for HP turbine inlet steam at >620°C and >220 bar. • No need for changes in component supply chain or any notable Capital Expenditures. 5 Decreasing component cost, increasing performance, and extending time between outages represent direct value propositions to GE and their customers. For the American consumer, these objectives translate into increased grid reliability (fewer unexpected outages), decreased Levelized Cost of Electricity, and improved environmental health (low-loading/load following to accelerate penetration of renewables). The results also have implications for wear resistant tooling, wire arc additive manufacturing, more durable components for syngas cleanup, and deployment of more efficient thermochemical pathways for carbon negative fuel production

09 BIOMASS FUELS↗
DOE OSTI2025

Corrosion Fatigue Life Evaluation of 17-4PH in Support of Water Filled Turbine Hubs

High cycle corrosion fatigue (HCCF) life S-N tests were conducted on wrought 17-4PH in various water environments under accelerated testing conditions. For tests conducted in aerated Columbia River water and in aerated ASTM Type IV water, at ~10 6 cycles, the HCCF stress amplitude was ~70% of the value in air. For deaerated water, the value was ~80%. These values are consist with the small amount of literature data on HCCF life of 17-4PH in water environments. The measured fatigue life both in air and water are much better than the ASME trend curve of high cycle fatigue life of moderate and high strength steels. Measured values were also much better than found in a hydropower-relevant study in the literature on cast 17-4PH. The effect of Amersite 61W on HCCF life was evaluated and found to cause very low times to specimen failure compared to all other water environments.

13 HYDRO ENERGY↗
DOE OSTI2021

Thermal Stability and Lattice Strain Evolution of High-Nb-Containing TiAl Alloy under Low-Cycle-Fatigue Loading

The micromechanical behavior and the effect of temperature on the micromechanical mechanism of high-Nb-containing TiAl alloy during low-cycle fatigue still remain uncertain. Herein, in situ and ex situ synchrotron-based high-energy X-ray (HEXRD) experiment results reveal that the gamma and omega(o) phases suffer compressive lattice strains but the lattice strain in the alpha(2) phase evolves from tensile to compressive during low-cycle fatigue at 900 degrees C. In addition, the three phases suffer compressive lattice strains during cooling to room temperature, which could result in larger compressive lattice strains in gamma and omega(o) phases and the change of the lattice strain state in the alpha(2) phase. The peak-broadening results show gamma recrystallization is dominant in the interrupted low-cycle-fatigue samples, whereas inhomogeneous deformation occurs in the failed low-cycle-fatigue samples. The performed synchrotron diffraction experiments offer a deeper insight into the phase transformations and micromechanism of TiAl alloy during low-cycle fatigue.

cyclic stress-strain behavior↗
DOE OSTI2022

Fatigue Behavior and Mechanisms of High-Entropy Alloys

Fatigue failures of structural materials pose enormous risks to in-service structures, as well as human lives. The development of advanced durable structural materials with fatigue resistance has important social impact. The novel concept of high-entropy alloys (HEAs) has engendered considerable attention due to their exhibited unusual mechanical properties, and correspondingly opening a new road to design fatigue-resistant structural materials. Here, the present work discusses and reviews the current findings on fatigue behavior and mechanisms of HEAs. Based on the understanding of fatigue-resistant favorable deformation mechanisms in HEAs, the perspectives from the viewpoint of materials design are provided to advance the development of fatigue-resistant HEAs, and future works are also suggested.

36 MATERIALS SCIENCE↗