Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high burnup”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Investigating the Role of Accident Tolerant Cladding on Source Term Reduction for High-Burnup PWRs Using MELCOR

The use of accident tolerant fuel (ATF) cladding can increase coping times during and beyond design basis accidents. While such gains may be incremental, they provide a margin that can potentially be recovered to enable high-burnup (HBU) operation. Realizing such a margin requires demonstrating that the combination of HBU and ATF has not led to an overall increase in source term. This study investigates the influence of cladding technology (Zr-based, Cr-coated Zr, and FeCrAl) and fuel cycle length (18 and 24 months) on radiological dose at the boundary of the exclusion zone for a four-loop pressurized water reactor to investigate whether ATF claddings can provide such benefits. We analyze a recovered large break loss-of-coolant accident scenario to investigate the impact of transient timescale on the benefits of such coping time increases. The simulations have been performed using the MELCOR and MELCOR Accident Consequence Code System codes. For the cases analyzed, increased fuel cycle length did not necessarily increase radionuclide release and hydrogen generation, as these were found to be sensitive to the core power distribution. Similarly, off-site dose consequence is dominated by short-lived radionuclides that tend to saturate earlier in the burnup, so higher burnup operation did not necessarily increase the source term for the phenomena and transients analyzed here. Delays in recovery of the lowpressure safety injection system increase hydrogen production and radionuclide release, especially between 780 s and 1620 s, due to the nonlinear oxidation and core degradation behavior. Results show that Cr-coated Zr enhances safety by delaying heatup and gap release. Here, when uncertainty propagation on oxidation properties is considered, FeCrAl exhibits the lowest overall radionuclide release and off-site dose throughout the spectrum. However, while the considered “base model” performance is superior under delayed injection scenarios, upper-bound cases display hydrogen generation risk comparable to the Zr-based cladding.

Accident Tolerant Fuel↗
DOE OSTI2024

Thermal Conductivity Degradation in High Burnup U-Pu-Zr Fuel

Recent advancements in the characterization of irradiated U-Pu-Zr fuels have revealed complexities that challenge existing understanding of constituent redistribution. Traditionally, models have proposed three concentric regions within the fuel, each characterized by distinctive phases and porosity. However, through detailed analysis of high burnup U-Pu-Zr, we discovered the presence of four distinct constituent redistribution regions. Particularly novel is the observation of significant Pu redistribution, a previously unreported phenomenon that necessitates a reevaluation of current models. This work aims to delve deeper into these findings, seeking to correlate mesoscale measurements of thermal diffusivity and respective thermal conductivity with the phases present in each redistribution region. To achieve this objective, we employed mesoscale thermoreflectance methods using the unique, Idaho National Laboratory (INL) developed, Thermal Conductivity Microscope (TCM) at INL’s Irradiated Materials Characterization Laboratory. The TCM employs two tightly focused lasers: one for heating to generate periodic thermal waves in the substrate, and another spatially separated probe laser to detect changes in the optical reflectivity of the gold-coated substrate resulting from thermal wave diffusion. We conducted several thermal diffusivity measurements within each region of constituent redistribution of a U-19Pu-10Zr fuel pin cross section irradiated to 11 at. % burnup. The TCM measurement positions strategically aligned with transmission electron microscopy (TEM) lift-out locations previously collected from the fuel sample. Complementary microstructural analysis techniques such as optical and scanning electron microscopy (OM/SEM), electron probe microanalysis for chemical compositions, and TEM-based selective area electron diffraction (SAED) analysis for crystallographic insights into each phase were also utilized. This comprehensive approach allowed us to correlate local thermal diffusivity data with microstructural characteristics, enabling the computation of local thermal conductivity at each position. The significance of this contribution lies in its pioneering use of the TCM for ternary fuel mesoscale examination, shedding light on the previously overlooked effects of Pu redistribution on local thermal conductivity. By informing current models capturing constituent redistribution and heat transfer, our findings pave the way for more accurate predictions of metallic fuel performance. Moreover, this work sets the stage for future comparisons with similar TCM examinations on U-19Pu-10Zr fuels at ultra-low burnup, facilitating a comprehensive understanding of thermal property changes across different burnup levels. Ultimately, our study not only enriches our understanding of the thermophysical properties of individual redistribution regions within U-Pu-Zr fuel but also offers valuable insights for the design and operational parameters of proposed next-generation fast reactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Comparative post-irradiation examination of high burnup U-19Pu-10Zr: Assessing steady-state irradiation behavior against historical and modeled fuel performance

Here, the development of next-generation sodium-cooled fast reactors necessitates comprehensive research on metallic fuels to maximize economic performance while ensuring safe operation. In this study, we investigated the steady-state irradiation behavior of two high burnup U-19Pu-10Zr fuel pins, DP-36 and DP-40, in preparation for planned safety testing. Post-irradiation examination (PIE) was performed to quantify fuel column elongation, regions of low-density at the top of the fuel column, pin deformation, fission product distribution, fractional fission gas release, microstructural evolution, and fuel constituent redistribution. Benchmarking against existing PIE data from U-19Pu-10Zr fuel pins irradiated in EBR-II revealed consistent patterns in fuel column elongation and cladding diametral strain. However, both pins exhibited longer low-density structures, and destructive examination of DP-36 revealed more complex constituent redistribution patterns compared to previously reported data for ternary fuel pins. The steady-state irradiation of both pins was also modeled using BISON. Comparisons of PIE results with modeled predictions showed overall agreement in fractional fission gas release but consistent overestimation of axial and radial swelling due to gaseous and solid swelling models. These findings underscore the critical importance of pre-test characterization on test and sibling pins to accurately capture steady-state fuel behavior ahead of transient testing, thus establishing a baseline for post-test comparison. Additionally, these analyses identified key data gaps that warrant further investigation to improve the understanding and prediction of fuel swelling, thereby enhancing the synergy between modeling and experimental efforts in supporting accident testing.

BISON↗
DOE OSTI2025

Effects of grain size and porosity on cladding failure in high-burnup UO 2 : A sensitivity and uncertainty study

Isotopic taggants are being studied to aid in the provenance assessment of nuclear materials. However, these taggants must be selected such that they do not adversely affect fuel performance during normal operation or accident scenarios. Taggants are known to affect the fuel’s grain size and porosity. In the work described in this paper, the BISON fuel performance code was used to assess the potential effects of taggants (i.e., grain size and porosity) on fuel rod behavior and cladding failure during a high-burnup, large-break loss-of-coolant accident. Here, 281 individual fuel rods from the same reactor core were modeled for a sensitivity study, a parametric study, and uncertainty quantification. The cladding failure predictions often exhibited stochastic behavior. After additional study, it was found that the cladding failure model is highly sensitive to residual error inherent to numerical approximation solvers. Some strategies to mitigate this sensitivity are discussed. The study found no relationship between known taggant effects and cladding failure status. However, taggants were found to affect the time and location of failure in certain rods. In conclusion, future work to continue investigating and validating these findings is briefly discussed.

Doped UO 2↗
DOE OSTI2024

Status Report on Characterization of High Burnup Fuel with Advanced Nondestructive Pulsed Neutron PIE

Characterizing irradiated or spent nuclear fuels with pulsed neutron techniques provides microstructural data such as phase fractions as well as crystallographic data, e.g. lattice parameters, from diffraction analysis. Diffraction characterization is complemented by spatially resolved mapping of isotope densities from energy-resolved neutron imaging, in particular neutron absorption resonance imaging, and overall bulk isotope assay with better sensitivity for minority isotopes from neutron absorption resonance spectroscopy without spatial resolution. Furthermore, after characterization at ambient condition, heating of irradiated or spent fuel will allow to characterize differences of e.g. lattice thermal expansion or phase transition temperature and kinetics compared to fresh fuel as well as enable the study of disappearance of irradiation defects. This data enables benchmarking of predictions of properties of irradiated fuels for which otherwise experimental data is sparse. The effort described here strives to characterize a section cut from a high-burnup fuel. Volumes smaller than entire fuel pellets or rodlets as proposed here, e.g. sections cut from a fuel pellet, to pave the way to characterize entire pellets or rodlets in the future.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Using X-ray spectrum imaging to quantify fission gas in high-burnup UO2 fuel

Analysis of fission gas bubbles (FGBs) in light-water reactor (LWR) fuel is needed to improve the understanding and predictive capability of fuel evolution under normal- and transient conditions. One of the most important parameters of a FGB is the pressure of the gas, primarily Xe, inside it. Bubble volume and location (inter- vs. intragranular) are important considerations as well. However, experimental analysis of such bubbles is challenging due to their small size and embedded nature, and usefulness of the data requires large numbers be analyzed. This paper proposes a method to measure the pressure of Xe bubbles using X-ray spectrum imaging (XSI) in scanning transmission electron microscopy (STEM). From X-ray generation and instrumental parameters, the number of Xe atoms yielding a given number of Xe L-series X-ray counts is estimated, and then from the estimated volume of the bubble the Xe density is estimated, which can then be converted to pressure via an equation-of-state. We apply the method to XSI datasets from high burnup (HBu) fuel from North Anna 1 reactor in as-irradiated and post-LOCA-test conditions and find Xe pressures in the FGBs clustered around 1 GPa.

Parish, Chad [ORNL] (ORCID:0000000312097439)↗
DOE OSTI2025

Design and full core fuel performance assessment of high burnup cores for 4-loop PWRs

Increasing the fuel discharge burnup of current light water reactors (LWRs) promises reductions in fuel cycle and/or operations costs. By assuming a constant core power density, the economic gain is enabled by better fuel utilization and/or an increased capacity factor. In this effort to investigate greater than 62 MWd/kgU maximum rod average burnup for 110+ kW/l core power density, two core designs have been developed for a standard 17x17, 193 fuel assemblies pressurized water reactor (PWR). The levelized unit cost methodology is employed to evaluate fuel cycle, operation and maintenance, and capital cost impacts and to examine the economic viability of both core design pathways. Core design and optimization are performed using the commercial STUDSVIK code package. Fuel performance analysis is realized in full core configuration via auditing FRAPCON4.1, FAST1.2, and the high-fidelity code BISON. To provide a realistic assessment, the core design process takes into consideration best practices in current PWR core design. It features acceptable performance in terms of various core design constraints on maximum allowable peaking and boron concentration. Gadolinia (Gd2O3) is used as a burnable poison with a maximum of 9 wt% concentration while feeding 89 or 77 fuel assemblies in a 3-batch refueling scheme. Full core fuel performance simulation, which allows for characterization of relevant fuel temperatures, plenum pressures, stresses, and strains, is performed with respect to two bounding burnup levels. Such performance is potentially licensable for the 18-month high burnup core (<68 MWd/kgU peak pin), while it is more challenging for the 24-month high burnup core design pathway (<75 MWd/kgU peak pin). Maximum rod plenum pressure is identified as the most limiting fuel performance parameter. Here, while the scope of the present study focuses on the steady-state plus overpower conditions, the acceptability of the new discharge burnup has to be further assessed by considering uncertainties and impacts under accident scenarios in the future.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

HIGH BURNUP FUEL-COOLANT INTERACTION ANALYSIS SUPPORTING FUEL SAFETY TESTING AT IDAHO NATIONAL LABORATORY

In the near future, experiments on HBu fuel under loss-of-coolant accident (LOCA) and reactivity-initiated accident (RIA) conditions will be performed within the Transient Reactor Test Facility (TREAT) at Idaho National Laboratory (INL). These experiments will be performed using the Transient Water Irradiation System for TREAT (TWIST) experiment vehicle. To support these experiments, analysis of fuel-coolant interaction (FCI) energetics is underway. This paper discusses FCIs in the context of light water reactor (LWR) safety, differentiating between the severe accident focus of commercial reactors and experimental RIA test programs where FCIs have occurred. However, it is highlighted that as the nuclear industry aims for increased burnup limits, the FCI events observed in RIA test programs may become relevant to commercial LWR safety analysis. The paper then presents developments to the UW-FCI computer program to enable simulation of FCIs initiated by solid fuel particles dispersing into the coolant during RIAs.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Supplement Analysis for the Proposed Shipment of High Burnup Research Cask to Idaho National Laboratory for Research and Development Purposes

DOE needs to continue with the HBUSFDP and transfer the HBURC to a facility capable of examination and testing of HBU SNF. These types of facilities do not exist at NAPS but are available at DOE national laboratories. The removal and eventual opening of the TN-32B research cask will provide DOE with the opportunity to gather data that will support continued safe storage of SNF at existing nuclear power plants, or a future federal consolidated storage facility. This effort will also help build public trust and confidence by demonstrating DOE’s ability to safely and securely transport commercial SNF using the certified Atlas rail consist.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Impact of recent ENDF nuclear data update, high initial enrichment and high burnup fuel on critical experiments applicability determination via the integral index c k for burnup credit validation

In 2012, NUREG/CR-7109 reported on the validation of burnup credit calculations involving major and minor actinides and major fission products which was investigated for pressurized and boiling water reactor (PWR and BWR) fuel enrichments up to 5 wt% 235 U and assembly-average burnups up to 60 GWd/MTU. Recently, there has been interest in increasing the maximum enrichment used in PWR fuel as high as 8 wt% 235 U and correspondingly increasing the maximum assembly-average burnups to approximately 75 GWd/MTU. These proposed increases in enrichment and burnup necessitate reinvestigation of the validation basis for k eff calculations for this expanded application space. Additionally, the 2012 study was performed by using the Evaluated Nuclear Data File (ENDF)/B-VII.0 nuclear data with the SCALE 6 covariance library, and the effects of using the newly released ENDF/B-VII.1 and ENDF/B-VIII.0 nuclear data and covariance libraries should be evaluated. In this work, published in NUREG/CR-7309 in 2025, the validation assessment was performed consistently with NUREG/CR-7109: modeling irradiated fuel assemblies in the Generic Burnup Credit (GBC)-32 cask defined in NUREG/CR-6747. The TSUNAMI-3D sequence was used to generate sensitivity data for the application model, and the data were compared with sensitivity data from select benchmark models. The integral parameter c k is the metric of similarity used in this study and is consistent with NUREG/CR-7109, where a c k value in excess of 0.8 indicates sufficient similarity for use in validation. A new set of benchmark experiments with sensitivity data has been assembled for this effort. The number of experiments with available sensitivity data is now 2,104, compared to 474 in NUREG/CR-7109. This increase was facilitated by the efforts of the Nuclear Energy Agency to generate sensitivity data for a majority of the experiments in the International Criticality Safety Benchmark Evaluation Project (ICSBEP) Handbook to supplement the data available in the Oak Ridge National Laboratory (ORNL) Verified, Archived Library of Inputs and Data (VALID). The complete set of benchmarks considered here includes experiments for low-enriched uranium (LEU), intermediate enriched uranium (IEU), and a mixture of uranium and plutonium (MIX) from the ICSBEP Handbook and VALID, as well as ORNL models of the Haut Taux de Combustion (HTC) experiments and other potentially relevant models not included in VALID. The updated similarity study shows that none of the extended burnup and higher enrichment combinations considered show a significant decrease in the number of potentially applicable experiments, meaning sufficient critical experiments exist for the validation of BUC criticality safety calculations, with initial enrichments up to 8 wt% 235 U and burnups up to 80 GWd/MTU. Additionally, both the ENDF/B-VII.1 and ENDF/B-VIII.0 nuclear data libraries can be used for validation since the number of critical experiments applicable for validation increases for most cases with the most recent nuclear data compared to the previous one. As in previous BUC validation studies, the French HTC experiments are the most similar in a majority of the application cases studied, especially from representative discharge burnups ranging from 40 to 80 GWd/MTU. In conclusion, these results match the conclusions presented in NUREG/CR-7109 regarding validation of the primary actinides in BUC analyses.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

High-Burnup Spent Fuel Data Project Sibling Pin Test Campaign Closeout Summary

The Used Fuel Disposition Campaign (UFDC) was established within the United States (U.S.) Department of Energy (DOE) Office of Nuclear Energy (NE) to conduct research and development (R&D) activities associated with storage, transportation, and disposal of used or spent nuclear fuel (UNF or SNF) and high-level radioactive waste.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Characterization of Fuel Cladding Chemical Interaction on a High Burnup U-10Zr Metallic Fuel via Electron Energy Loss Spectroscopy Enhanced by Machine Learning

Fuel cladding chemical interaction (FCCI) is one of the main performance limiting factors for metallic nuclear fuels. The interaction destabilizes the martensitic microstructure and deteriorates mechanical properties of HT-9 cladding. The detection of low atomic number elements (Z<10) and overlapping of elemental peaks can be problematic in interpreting energy dispersive X-ray spectroscopy (EDS) data. Electron energy loss spectroscopy (EELS) provides precise elemental edge energy values and can detect elements with a low atomic number. This work utilizes EELS to study the distribution of lanthanides and light elements at the interaction region. The sample was prepared from the FCCI region of a U-10Zr (wt.%) solid fuel with HT-9 cladding, irradiated to a burnup of 13.2 at.%. Processing the EELS data included three major steps: 1) enhance the signal to noise ratio by denoising the spectrum with principal component analysis (PCA) method, removing background and performing deconvolution; 2) identify chemical elements with core energy loss edges; 3) confirm different phases using a popular machine learning method, K-means. This work presents qualitative assessment of lanthanides and light elements like carbon (C) and oxygen (O) enhanced by the application of machine learning algorithms. By comparing with EDS elemental maps, EELS provides higher resolution chemical maps, reveals the distribution of carbon at the interaction region supporting the formation of zirconium carbide, a rind-like microstructure feature that was proposed to mitigate the chemical interaction. Furthermore, the plasmon peak map was also found to indicate an energy shift associated with the formation of phases/compounds. K-means clustering method was used on the processed electron energy loss (EEL) spectrum to automatically reveal different phases. The resulting clustered maps from K-means clustering align well with elemental maps confirming certain phases, especially Fe-Ce and Zr-C, in the FCCI region.

EELS↗
DOE OSTI2026

Full-core high-burnup BWR LOCA fuel performance analysis and FFRD susceptibility

The susceptibility of the boiling water reactor (BWR) Limerick Unit 1 to fuel fragmentation, relocation, and dispersal during a postulated large-break loss-of-coolant accident (LBLOCA) was calculated using a multiphysics framework. The simulations include full-core, rod-resolved neutronic, thermal hydraulic, and fuel performance models using the VERA, TRACE, and BISON codes. This work focused on the transient BISON simulations, which include both the normal operation and LBLOCA periods in the same simulations. Cladding integrity was assessed using two correlations that are included with BISON. make page break Several new BWR-specific features were recently added to BISON. This work represents the first time these features have been included in a core-scale set of simulations. This study hence evaluates the performance of these new models for an operating reactor with realistic operating conditions. Simulation results showed that cladding integrity was maintained (i.e., no rods burst). Finally, future work to improve BWR and PWR predictions using this framework is suggested.

BISON↗
DOE OSTI2025

Core Physics Characteristics of Extended Enrichment and High Burnup Boiling Water Reactor Fuel

This paper presents the highlights of boiling water reactor (BWR) core physics studies performed at Oak Ridge National Laboratory as part of a series of studies conducted to compare low-enriched uranium (LEU) with LEU+ fuel. The studies analyzed isotopic fuel content, lattice parameters (Phase 1), and core physics (Phase 2) to identify challenges in operation, storage, and transportation for BWRs and pressurized water reactors (PWRs). Because of a lack of publicly available lattice and core designs for modern BWR fuel assemblies and reactor cores, several optimized lattice designs were generated, and different core loading strategies were investigated. Twelve optimized lattice designs with 235 U enrichments ranging from 1.6% to 9% and gadolinia loadings ranging from 3 to 8 wt% were used to model axial enrichment and geometry variations in fuel assemblies for core designs. Each core shares a common set of approximations in design and analysis to allow for consistent comparisons between LEU and LEU+ fuel. The objective is to highlight anticipated changes in core behavior with respect to the reference LEU core. The results of this study show that the differences in LEU and LEU+ core reactor physics characteristics are less significant than the differences in lattice physics characteristics reported in the Phase 1 studies.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗