SEARCH · Engineering Papers

Results for “grid impact analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Extended operating range of the 30-cm ion thruster with simplified power processor requirements

A two grid 30 cm diameter mercury ion thruster was operated with only six power supplies over the baseline J series thruster power throttle range with negligible impact on thruster performance. An analysis of the functional model power processor showed that the component mass and parts count could be reduced considerably and the electrical efficiency increased slightly by only replacing power supplies with relays. The input power, output thrust, and specific impulse of the thruster were then extended, still using six supplies, from 2660 watts, 0.13 newtons, and 2980 seconds to 9130 watts, 0.37 newtons, and 3820 seconds, respectively. Increases in thrust and power density enable reductions in the number of thrusters and power processors required for most missions. Preliminary assessments of the impact of thruster operation at increased thrust and power density on the discharge characteristics, performance, and lifetime of the thruster were also made.

Rawlin, V. K.↗

NASA NTRS1987

Utilization of satellite data in mesoscale modeling of severe weather

The Visible Infrared Spin Scan Radiometer Atmospheric Sounder (VAS) data were used to model the 36 hour cyclogenesis period over the Pacific Ocean. Various combinations of VAS data, conventional radiosonde data, and gridded data from the National Weather Service global analysis were used in successive-correction and variational objective-analysis procedures. The Penn State/NCAR mesoscale model was used to test the impact of the VAS data on a 12 hour forecast of convective precipitation in the midweastern U.S.

Warner, Thomas T.↗

NASA NTRS2017

Finite Element Simulation of Three Full-Scale Crash Tests for Cessna 172 Aircraft

The NASA Emergency Locator Transmitter Survivability and Reliability (ELT-SAR) project was initiated in 2013 to assess the crash performance standards for the next generation of emergency locator transmitter (ELT) systems. Three Cessna 172 aircraft were acquired to perform crash testing at NASA Langley Research Center's Landing and Impact Research Facility. Full-scale crash tests were conducted in the summer of 2015 and each test article was subjected to severe, but survivable, impact conditions including a flare-to-stall during emergency landing, and two controlled-flight-into-terrain scenarios. Full-scale finite element analyses were performed using a commercial explicit solver, ABAQUS. The first test simulated impacting a concrete surface represented analytically by a rigid plane. Tests 2 and 3 simulated impacting a dirt surface represented analytically by an Eulerian grid of brick elements using a Mohr-Coulomb material model. The objective of this paper is to summarize the test and analysis results for the three full-scale crash tests. Simulation models of the airframe which correlate well with the tests are needed for future studies of alternate ELT mounting configurations.

Mason, Brian H.↗

NASA NTRS2019

Sketch-To-Solution: An Exploration of Viscous CFD with Automatic Grids

Numerical simulation of the Reynolds-averaged Navier–Stokes (RANS) equations has become a critical tool for the design of aerospace vehicles. However, the issues that affect the grid convergence of three dimensional RANS solutions are not completely understood, as documented in the AIAA Drag Prediction Workshop series. Grid adaption methods have the potential for increasing the automation and discretization error control of RANS solutions to impact the aerospace design and certification process. The realization of the CFD Vision 2030 Study includes automated management of errors and uncertainties of physics-based, predictive modeling that can set the stage for ensuring a vehicle is in compliance with a regulation or specification by using analysis without demonstration in flight test (i.e., certification or qualification by analysis). For example, the Cart3D inviscid analysis package has automated Cartesian cut-cell gridding with output-based error control. Fueled by recent advances in the fields of anisotropic grid adaptation, error estimation, and geometry modeling, a similar work flow is explored for viscous CFD simulations; where a CFD application engineer provides geometry, boundary conditions, and flow parameters, and the sketch-to-solution process yields a CFD simulation through automatic, error-based, grid adaptation.

Kleb, William L.↗

NASA NTRS2023

The optimization of model ensemble composition and size can enhance the robustness of crop yield projections

Linked climate and crop simulation models are widely used to assess the impact of climate change on agriculture. However, it is unclear how ensemble configurations (model composition and size) influence crop yield projections and uncertainty. Here, we investigate the influences of ensemble configurations on crop yield projections and modeling uncertainty from Global Gridded Crop Models and Global Climate Models under future climate change. We performed a cluster analysis to identify distinct groups of ensemble members based on their projected outcomes, revealing unique patterns in crop yield projections and corresponding uncertainty levels, particularly for wheat and soybean. Furthermore, our findings suggest that approximately six Global Gridded Crop Models and 10 Global Climate Models are sufficient to capture modeling uncertainty, while a cluster-based selection of 3-4 Global Gridded Crop Models effectively represents the full ensemble. The contribution of individual Global Gridded Crop Models to overall uncertainty varies depending on region and crop type, emphasizing the importance of considering the impact of specific models when selecting models for local-scale applications. Our results emphasize the importance of model composition and ensemble size in identifying the primary sources of uncertainty in crop yield projections, offering valuable guidance for optimizing ensemble configurations in climate-crop modeling studies tailored to specific applications.

Agriculture↗

NASA NTRS1993

Blasim: A computational tool to assess ice impact damage on engine blades

A portable computer called BLASIM was developed at NASA LeRC to assess ice impact damage on aircraft engine blades. In addition to ice impact analyses, the code also contains static, dynamic, resonance margin, and supersonic flutter analysis capabilities. Solid, hollow, superhybrid, and composite blades are supported. An optional preprocessor (input generator) was also developed to interactively generate input for BLASIM. The blade geometry can be defined using a series of airfoils at discrete input stations or by a finite element grid. The code employs a coarse, fixed finite element mesh containing triangular plate finite elements to minimize program execution time. Ice piece is modeled using an equivalent spherical objective that has a high velocity opposite that of the aircraft and parallel to the engine axis. For local impact damage assessment, the impact load is considered as a distributed force acting over a region around the impact point. The average radial strain of the finite elements along the leading edge is used as a measure of the local damage. To estimate damage at the blade root, the impact is treated as an impulse and a combined stress failure criteria is employed. Parametric studies of local and root ice impact damage, and post-impact dynamics are discussed for solid and composite blades.

Reddy, E. S.↗

NASA NTRS1999

Thermal Analysis of Magnetically-Coupled Pump for Cryogenic Applications

Magnetically-coupled pump is under evaluation at Kennedy Space Center for possible cryogenic applications. A major concern is the impact of low temperature fluid flows on the pump performance. As a first step toward addressing this and related issues, a computational fluid dynamics and heat transfer tool has been adopted in a pump geometry. The computational tool includes (i) a commercial grid generator to handle multiple grid blocks and complicated geometric definitions, and (ii) an in-house computational fluid dynamics and heat transfer software developed in the Principal Investigator's group at the University of Florida. Both pure-conduction and combined convection-conduction computations have been conducted. A pure-conduction analysis gives insufficient information about the overall thermal distribution. Combined convection-conduction analysis indicates the significant influence of the coolant over the entire flow path. Since 2-D simulation is of limited help, future work on full 3-D modeling of the pump using multi-materials is needed. A comprehensive and accurate model can be developed to take into account the effect of multi-phase flow in the cooling flow loop, and the magnetic interactions.

Senocak, Inanc↗

NASA NTRS2012

Preliminary Results of a U.S. Deep South Warm Season Deep Convective Initiation Modeling Experiment using NASA SPoRT Initialization Datasets for Operational National Weather Service Local Model Runs

The initiation of deep convection during the warm season is a forecast challenge in the relative high instability and low wind shear environment of the U.S. Deep South. Despite improved knowledge of the character of well known mesoscale features such as local sea-, bay- and land-breezes, observations show the evolution of these features fall well short in fully describing the location of first initiates. A joint collaborative modeling effort among the NWS offices in Mobile, AL, and Houston, TX, and NASA s Short-term Prediction Research and Transition (SPoRT) Center was undertaken during the 2012 warm season to examine the impact of certain NASA produced products on the Weather Research and Forecasting Environmental Modeling System. The NASA products were: a 4-km Land Information System data, a 1-km sea surface temperature analysis, and a 4-km greenness vegetation fraction analysis. Similar domains were established over the southeast Texas and Alabama coastlines, each with a 9 km outer grid spacing and a 3 km inner nest spacing. The model was run at each NWS office once per day out to 24 hours from 0600 UTC, using the NCEP Global Forecast System for initial and boundary conditions. Control runs without the NASA products were made at the NASA SPoRT Center. The NCAR Model Evaluation Tools verification package was used to evaluate both the forecast timing and location of the first initiates, with a focus on the impacts of the NASA products on the model forecasts. Select case studies will be presented to highlight the influence of the products.

Medlin, Jeffrey M.↗

NASA NTRS2012

Characterization of Turbulent Latent and Sensible Heat Flux Exchange Between the Atmosphere and Ocean in MERRA

Turbulent fluxes of heat and moisture across the atmosphere-ocean interface are fundamental components of the Earth's energy and water balance. Characterizing both the spatiotemporal variability and the fidelity of these exchanges of heat and moisture is critical to understanding the global water and energy cycle variations, quantifying atmosphere-ocean feedbacks, and improving model predictability. This study examines the veracity of the recently completed NASA Modern-Era Retrospective analysis for Research and Applications (MERRA) product with respect to its representation of the surface turbulent heat fluxes. A validation of MERRA turbulent heat fluxes and near-surface bulk variables at local, high-resolution space and time scales is achieved by making comparisons to a large suite of direct observations. Both in situ and satellite-observed gridded surface heat flux estimates are employed to investigate the spatial and temporal variability of the surface fluxes with respect to their annual mean climatologies, their seasonal covariability of near-surface bulk parameters, and their representation of extremes. The impact of data assimilation on the near-surface parameters is assessed through evaluation of incremental analysis update tendencies produced by the assimilation procedure. It is found that MERRA turbulent surface heat fluxes are relatively accurate for typical conditions but have systematically weak vertical gradients in moisture and temperature and have a weaker covariability between the near-surface gradients and wind speed than found in observations. This results in an underestimate of the surface latent and sensible heat fluxes over the western boundary current and storm track regions. The assimilation of observations mostly acts to bring MERRA closer to observational products by increasing moisture and temperature near the surface and decreasing the near-surface wind speeds. The major patterns of spatial and temporal variability of the turbulent heat fluxes produced by MERRA compare favorably to observationally based estimates. However, MERRA is distinct in terms of amplitude. These results suggest that MERRA is likely to be a valuable resource for a number of research applications though, as with all turbulent flux estimates, systematic issues should be taken into account

Robert, J. Brent↗

NASA NTRS2012

Characterization of Turbulent Latent and Sensible Heat Flux Exchange Between the Atmosphere and Ocean in MERRA

Turbulent fluxes of heat and moisture across the atmosphere-ocean interface are fundamental components of the Earth s energy and water balance. Characterizing both the spatiotemporal variability and the fidelity of these exchanges of heat and moisture is critical to understanding the global water and energy cycle variations, quantifying atmosphere-ocean feedbacks, and improving model predictability. This study examines the veracity of the recently completed NASA Modern-Era Retrospective analysis for Research and Applications (MERRA) product with respect to its representation of the surface turbulent heat fluxes. A validation of MERRA turbulent heat fluxes and near-surface bulk variables at local, high-resolution space and time scales is achieved by making comparisons to a large suite of direct observations. Both in situ and satellite-observed gridded surface heat flux estimates are employed to investigate the spatial and temporal variability of the surface fluxes with respect to their annual mean climatologies, their seasonal covariability of near-surface bulk parameters, and their representation of extremes. The impact of data assimilation on the near-surface parameters is assessed through evaluation of incremental analysis update tendencies produced by the assimilation procedure. It is found that MERRA turbulent surface heat fluxes are relatively accurate for typical conditions but have systematically weak vertical gradients in moisture and temperature and have a weaker covariability between the near-surface gradients and wind speed than found in observations. This results in an underestimate of the surface latent and sensible heat fluxes over the western boundary current and storm track regions. The assimilation of observations mostly acts to bring MERRA closer to observational products by increasing moisture and temperature near the surface and decreasing the near-surface wind speeds. The major patterns of spatial and temporal variability of the turbulent heat fluxes produced by MERRA compare favorably to observationally based estimates. However, MERRA is distinct in terms of amplitude. These results suggest that MERRA is likely to be a valuable resource for a number of research applications though, as with all turbulent flux estimates, systematic issues should be taken into account.

Roberts, J. Brent↗

NASA NTRS1984

Observing system simulation experiments related to space-borne Lidar wind profiling. Part 1: Forecast impacts of highly idealized observing systems

Simulation experiments comparing the relative importance of an idealized LIDAR wind profiling system with idealized temperature and pressure sounding systems on 12 h forecasts are studied for three "nature' fields representing the true evolving atmospheric states. The three fields are obtained respectively from: (1) a long integration of the GLAS 4th Order Model (4 deg lat x 5 deg lon x 9 levels), (2) a continuous sequence of NMC operational analysis and, (3) a long integration of the ECMWF high resolution (1.875 deg 1 lat x 1.875 deg lon x 15 layers) operational forecast model. These fields are interpolated to the grid of the GLAS model and used for simulating the observed global analysed fields of winds, temperature, moisture and surface pressure. The same interpolated fields are also used for verification of forecast impact. The effects of clouds, aerosol concentrations, and instrument accuracies on the simulated observation will be discussed.

Halem, M.↗

NASA NTRS2019

Geometry Modeling for Unstructured Mesh Adaptation

The quantification and control of discretization error is critical to obtaining reliable simulation results. Adaptive mesh techniques have the potential to automate discretization error control, but have made limited impact on production analysis workflow. Recent progress has matured a number of independent implementations of flow solvers, error estimation methods, and anisotropic mesh adaptation mechanics. However, the poor integration of initial mesh generation and adaptive mesh mechanics to typical sources of geometry has hindered adoption of adaptive mesh techniques, where these geometries are often created in Mechanical Computer- Aided Design (MCAD) systems. The difficulty of this coupling is compounded by two factors: the inherent complexity of the model (e.g., large range of scales, bodies in proximity, details not required for analysis) and unintended geometry construction artifacts (e.g., translation, uneven parameterization, degeneracy, self-intersection, sliver faces, gaps, large tolerances be- tween topological elements, local high curvature to enforce continuity). Manual preparation of geometry is commonly employed to enable fixed-grid and adaptive-grid workflows by reducing the severity and negative impacts of these construction artifacts, but manual process interaction inhibits workflow automation. Techniques to permit the use of complex geometry models and reduce the impact of geometry construction artifacts on unstructured grid workflows are models from the AIAA Sonic Boom and High Lift Prediction are shown to demonstrate the utility of the current approach.

Park, Michael A.↗

NASA NTRS1984

Calculation of two- and three-dimensional transonic cascade flow field using the Navier-Stokes equations

A Navier-Stokes analysis employing the time-dependent Linearized Block Implicit scheme (LBI) was applied to two-dimensional and three-dimensional transonic turbulent cascade flows. In general, the geometrical configuration of the turbine blade impacts both the grid construction procedure and the implementation of the numerical algorithm. Since modern turbine blades of interest are characterized by very blunt leading edges, rounded trailing edges and high stacking angles, a robust grid construction procedure is required that can accommodate the severe body shape while resolving regions of large flow gradients. A constructive O-type grid generation technique, suitable for cascades with rounded trailing edges, was developed and used to construct the C3X turbine cascade coordinate grid. Two-dimensional calculations were performed employing the Navier-Stokes procedure for the C3X turbine cascade, and the predicted pressure coefficients and heat transfer rates were compared with the experimental data. Three-dimensional Navier-Stokes calculations were also performed.

Weinberg, B. C.↗

NASA NTRS2022

The Lower Thermospheric Winter-To-Summer Meridional Circulation: 1: Driving Mechanism

In this study, the mechanism driving the narrow lower-thermospheric winter-to-summer meridional circulation is thoroughly investigated for the first time using the Specified Dynamics configuration runs of the Whole Atmosphere Community Climate Model eXtended (SD-WACCMX) simulations and the TIMED Doppler Interferometer (TIDI) observations. The mean meridional circulation in the SD-WACCMX is qualitatively consistent with the TIDI measurements, though the magnitude in the SD-WACCMX is about 50% weaker. The lower-thermospheric winter-to-summer circulation is mainly driven by the resolved wave forcing, including the tides and internally generated inertia gravity waves (GWs). The momentum forcing from the parameterized sub-grid scale GWs is not as significant as the resolved wave forcing in driving the lower-thermospheric meridional circulation. The GW parameterization scheme in the SD-WACCMX only includes GWs with phase velocities in the range of ±45 m/s, which might result in most of the parameterized sub-grid GWs dissipating and breaking in the mesosphere and hardly impacting the lower thermosphere. Only including slow GWs in the SD-WACCMX parameterization could potentially lead to the underestimation of the meridional wind in the model. Analysis also indicates the lower-thermospheric meridional circulation is stronger in the summer hemisphere, which is attributed to the hemispheric asymmetry in the resolved wave momentum forcing. This study underlines the importance of the whole atmosphere coupling through wave propagation and dissipation. This understanding can guide the model development with an accurate representation of underlying physical processes in the mesosphere and lower thermosphere which drives the lower-thermospheric circulation as well as the overall dynamics of this region.

Jack C. Wang↗

NASA NTRS2012

Evaluation of the Relative Contribution of Observing Systems in Reanalyses: Aircraft Temperature Bias and Analysis Innovations

Reanalyses have become important sources of data in weather and climate research. While observations are the most crucial component of the systems, few research projects consider carefully the multitudes of assimilated observations and their impact on the results. This is partly due to the diversity of observations and their individual complexity, but also due to the unfriendly nature of the data formats. Here, we discuss the NASA Modern-Era Retrospective analysis for Research and Applications (MERRA) and a companion dataset, the Gridded Innovations and Observations (GIO). GIO is simply a post-processing of the assimilated observations and their innovations (forecast error and analysis error) to a common spatio-temporal grid, following that of the MERRA analysis fields. This data includes in situ, retrieved and radiance observations that are assimilated and used in the reanalysis. While all these disparate observations and statistics are in a uniform easily accessible format, there are some limitations. Similar observations are binned to the grid, so that multiple observations are combined in the gridding process. The data is then implicitly thinned. Some details in the meta data may also be lost (e.g. aircraft or station ID). Nonetheless, the gridded observations should provide easy access to all the observations input to the reanalysis. To provide an example of the GIO data, a case study evaluating observing systems over the United States and statistics is presented, and demonstrates the evaluation of the observations and the data assimilation. The GIO data is used to collocate 200mb Radiosonde and Aircraft temperature measurements from 1979-2009. A known warm bias of the aircraft measurements is apparent compared to the radiosonde data. However, when larger quantities of aircraft data are available, they dominate the analysis and the radiosonde data become biased against the forecast. When AMSU radiances become available the radiosonde and aircraft analysis and forecast error take on an annual cycle. While this supports results of previous work that recommend bias corrections for the aircraft measurements, the interactions with AMSU radiances will also require further investigation. This also provides an example for reanalysis users in examining the available observations and their impact on the analysis. GIO data is presently available alongside the MERRA reanalysis.

Bosilovich, Michael G.↗

NASA NTRS2024

Influence of SMAP Soil Moisture Retrieval Assimilation on Runoff Estimation Across South Asia

This study was designed to characterize and quantify the influence of surface soil moisture assimilation on estimated runoff (surface flow and baseflow) and hydraulically-routed streamflow across three large river basins in South Asia that are at risk of impending water stress. Soil Moisture Active Passive (SMAP) surface soil moisture retrievals were assimilated into the Noah-MP land surface model. The gridded runoff was hydraulically routed to obtain volumetric streamflow values for a river network using a runoff routing module (Hydrological Modeling and Analysis Platform, HyMAP). The open loop (OL, model-only) and data assimilated (DA, includes soil moisture retrieval assimilation) Noah-MP runoff estimates highlighted the improvements in estimated total runoff across irrigated areas. Soil moisture assimilation impacted baseflow more relative to surface runoff. The HyMAP-based OL and DA streamflow generally underestimated the streamflow at upstream stations and overestimated the streamflow at downstream stations within the Indus basin due to missing physics related to reservoir operations. For stations located in the Ganges–Brahmaputra basins, the OL and DA estimation performance varied. The OL and DA results showed that the assimilation of soil moisture retrievals improves gridded runoff and volumetric streamflow across irrigated areas. Considerable relative change in streamflow (>70% increase in magnitude relative to OL) is noted after assimilation across the highly irrigated lower Indus basin and high precipitation regions in Bangladesh. Improving the modeling system’s representativeness of ground conditions via inclusion of water management information could improve large-scale streamflow modeling across South Asia.

soil moisture↗

NASA NTRS1985

Dynamic and static initialization of a mesoscale model using VAS satellite data

Various mesoscale weather forecast model initialization procedures were tested in seven simulation forecasts for a 12 hr period in July 1981. Attention was given to the impacts of using as input radiosonde data, VISSR Atmospheric Sounder (VAS) data and a combination of VAS and data from a smoothed global analysis. The data were assimilated with successive correction objective analysis procedures. The model had a 60 km horizontal grid-length resolution, 14 layers in the vertical, and accounted for short- and long-wave energy in the surface energy budget but not in the atmosphere. Conventional data were used for the mass and moisture fields. The trials showed that VAS data enhanced the predictions of the temperature and mass variables, while winds were least accurately predicted when VAS data were entered in the initializations. Finally, statically initialized precipitation forecasts from radiosonde and/or VAS data exhibited equal skill.

Beauchamp, J. G.↗

NASA NTRS2012

Integrating NASA Satellite Data Into USDA World Agricultural Outlook Board Decision Making Environment To Improve Agricultural Estimates

The USDA World Agricultural Outlook Board (WAOB) is responsible for monitoring weather and climate impacts on domestic and foreign crop development. One of WAOB's primary goals is to determine the net cumulative effect of weather and climate anomalies on final crop yields. To this end, a broad array of information is consulted. The resulting agricultural weather assessments are published in the Weekly Weather and Crop Bulletin, to keep farmers, policy makers, and commercial agricultural interests informed of weather and climate impacts on agriculture. The goal of the current project is to improve WAOB estimates by integrating NASA satellite precipitation and soil moisture observations into WAOB's decision making environment. Precipitation (Level 3 gridded) is from the TRMM Multi-satellite Precipitation Analysis (TMPA). Soil moisture (Level 2 swath and Level 3 gridded) is generated by the Land Parameter Retrieval Model (LPRM) and operationally produced by the NASA Goddard Earth Sciences Data and Information Services Center (GBS DISC). A root zone soil moisture (RZSM) product is also generated, via assimilation of the Level 3 LPRM data by a land surface model (part of a related project). Data services to be available for these products include GeoTIFF, GDS (GrADS Data Server), WMS (Web Map Service), WCS (Web Coverage Service), and NASA Giovanni. Project benchmarking is based on retrospective analyses of WAOB analog year comparisons. The latter are between a given year and historical years with similar weather patterns and estimated crop yields. An analog index (AI) was developed to introduce a more rigorous, statistical approach for identifying analog years. Results thus far show that crop yield estimates derived from TMPA precipitation data are closer to measured yields than are estimates derived from surface-based precipitation measurements. Work is continuing to include LPRM surface soil moisture data and model-assimilated RZSM.

Teng, William↗